Numerical investigation of avulsions in gravel-bed braided rivers

Gravel-bed braided rivers are highly energetic fluvial systems characterized by frequent in-channel avulsions, which govern the morphodynamics of such rivers and are essential for them to maintain a braided planform. However, the avulsion mechanisms within natural braided rivers remain unclear due to their complicated hydraulic and morphodynamic processes. Influenced by neighbouring channels, avulsions in braided rivers may differ from those of bifurcations in single-thread rivers, suggesting that avulsions should be studied within the context of the entire braid network. In this study, braiding evolution processes in gravel-bed rivers were simulated using a physics-based numerical model that considers graded bed-load transport by dividing sediment particles into multiple size fractions and vertical sediment sorting by dividing the riverbed into several vertical layers. The numerical model successfully produced braiding processes and avulsion activities similar to those observed in a laboratory river. Results show that bend evolution of the main channel was the fundamental process controlling the occurrence of avulsions in the numerical model, with a cyclic process of channel meandering by lateral migration that transitioned to a straight channel pattern by avulsion. The radius of bend curvature for triggering avulsions in the numerical model was measured and it was found that the highest probability for a channel bend to generate an avulsion occurs when its radius of curvature is approximately 2.0–3.3 times the average anabranch width. Other types of avulsion were also observed that did not occur specifically at meander bends, but upstream meander evolution indirectly influenced such avulsions by altering channel pattern and discharge to those locations. This study explored the processes and mechanisms of several types of avulsion, and proposed factors controlling their occurrence, namely increasing channel curvature, high shear stress, tributary discharge, riverbed gradient and upstream channel pattern, with high shear stress being a direct indicator. Furthermore, avulsions in a typical gravel-bed braided river, the Waimakariri River in New Zealand, were analysed using sequential Google Earth maps, which confirmed the conclusions derived from the numerical simulation.     

The role of salinity in fluvio-deltaic morphodynamics: A long-term modelling study

Salinity difference between terrestrial river discharge and oceanic tidal water plays a role in modifying the local flow field and, as a consequence, estuarine morphodynamics. Although widely recognized, recent numerical studies exploring the long-term morphological evolution of river-influenced estuaries with two-dimensional, depth-averaged models have mostly neglected salinity. Using a three-dimensional morphodynamic model, we aim to gain more insight into the effect of salinity on the morphodynamics of fluvio-deltaic systems. Model results indicate that the resultant estuarine morphology established after 600 years differs remarkably when a salinity gradient is included. A fan-shaped river-mouth delta exhibits less seaward expansion and is cut through by narrower channels when salinity is included. The inclusion of salinity tends to generate estuarine circulation, which favours landward sediment transport and hence limits the growth of the delta while enhancing the development of intertidal areas. The formation of deltaic channel–shoal patterns resulting from morphodynamic evolution tends to strengthen salinity stratification, which is characterized by an increased gradient Richardson number. The direction of the depth-averaged residual sediment transport over a tide may be opposite to the direction of residual velocity, indicating the significant influence of baroclinic effects on the net sediment transport direction (and hence morphological change). The effect of salinity on morphological evolution becomes less profound when the strength of tidal or fluvial forcing is dominant over the other. The effects of sediment type and flocculation, which are particularly important when salinity gradients are present, are also discussed. Overall, this study highlights that neglecting salinity to simulate long-term estuarine morphodynamics requires more careful justification, particularly when the environment is characterized by fine sediment types (favouring suspended transport), and relatively large river discharge and estuarine depth (favouring baroclinic effects). © 2020 John Wiley & Sons, Ltd.     

Experimental investigation of the morphodynamic response of riffles and pools to unsteady flow and increased sediment supply

Gravel-bed rivers characteristically exhibit shallow riffles in wide sections and deeper pools where the channel becomes constricted and narrow. While rivers can adjust to changing flow and sediment supply through some combination of adjustments of channel slope, bed-surface sorting, and channel shape, the degree to which riffle-pools may adopt these changes in response to changing flows and sediment supplies remains unclear. This article presents results from a flume experiment investigating how constant- and variable-width channels adjust their morphology in response to changing flow and increased sediment supply. Two flume geometries were used: (1) constant-width and (2) variable-width, characterized by a sinusoidal pattern with a mean width equal to that of the first channel. The variable-width channel developed bed undulations in phase with the width, representing riffle-pools. The experiment consisted of three phases for each flume geometry: (1) steady flow, constant sediment supply; (2) unsteady flow, constant sediment supply; and (3) unsteady flow, doubled sediment supply. Unsteady flow was implemented in the form of repeated symmetrical stepped hydrographs, with a mean discharge equal to that in the steady flow phase. In all phases the bed and sediment supply were composed of a sand/gravel mixture ranging from 1 to 8 mm. In both the straight and variable-width channels, transitioning from steady flow to repeated hydrographs did not result in significant changes in bed morphology. The two channel geometries had different responses to increased sediment supply: the slope of the straight channel increased nearly 40%, while the variable-width channel reduced the relief between bars and pools and decreased the variability in cross-sectional elevation with a slight slope increase. Bar-pool relief varied with repeat discharge hydrographs. Pool elevation changed twice the distance of bar elevations, emphasizing the relevance of pool scour for riffle-pool self-maintenance in channels with width variations.     

The job of the river

Earth scientists have traditionally conceptualized rivers and streams as geomorphic machines, whose role is to transfer sediment and to sculpt the landscape. Steady‐state relationships between sediment supply and transport capacity have traditionally been considered normative in fluvial systems. Rivers are hydrological entities, however, whose function is to redistribute excess moisture on land. The geomorphic work of the river – erosion, transport, deposition, etc. – is a byproduct of the hydrological job of the river. There is therefore no reason to expect any particular relationship between sediment supply and transport capacity to develop as a normative condition in fluvial systems. The apparent steady‐state equilibrium slope adjustments of rivers are a byproduct of four basic phenomena: (1) hydraulic selection, which favors channels and branching networks over other flux patterns; (2) water flows along the available path of least resistance; (3) energy dissipation; and (4) finite relaxation times. Recognizing converging trends of stream power or slope and sediment supply as common (but far from inevitable) side effects rather than self‐regulation has important implications for interpreting and predicting fluvial systems, and for river management and restoration. Such trends are variable, transient, contingent, and far from universal. Where they occur, they are an emergent byproduct of fundamental physical mechanisms, not a goal function or attractor state. Copyright © 2009 John Wiley & Sons, Ltd.     

Recent channel adjustments in alluvial rivers of Tuscany,central Italy

Drastic channel adjustments have affected the main alluvial rivers of Tuscany (central Italy) during the 20th century. Bed‐level adjustments were identified both by comparing available topographic longitudinal profiles of different years and through field observations. Changes in channel width were investigated by comparing available aerial photographs (1954 and 1993–98). Bed incision represents the dominant type of vertical adjustment, and is generalized along all the fluvial systems investigated. The Arno River system is the most affected by bed‐level lowering (up to 9 m), whereas lower incision (generally less than 2 m) is observed along the rivers of the southern part of the region. Human disturbances appear to be the dominant factors of adjustments: the main phase of vertical change occurred during the period 1945–80, in concomitance with the phase of maximum sediment mining activity at the regional scale. The second dominant type of adjustment that involved most of the rivers in the region consists of a narrowing of the active channel. Based on measurements of channel width conducted on aerial photographs, 38% of the reaches analysed experienced a narrowing greater than 50% of the initial channel width. The largest values of channel narrowing were observed along initially braided or sinuous with alternate bars morphologies in the southern portion of the region. A regional scheme of channel adjustments is derived, based on initial channel morphology and on the amounts of incision and narrowing. Different styles of channel adjustments are described. Rivers that were originally sinuous with alternate bars to braided generally became adjusted by a moderate incision and a moderate to intense narrowing; in contrast, sinuous‐meandering channels mainly adjusted vertically, with a minor amount of narrowing. Copyright © 2003 John Wiley & Sons, Ltd.     

Riparian vegetation life stages control the impact of flood sequencing on braided river morphodynamics

With riverine flooding set to be more frequent in many parts of the world as a result of climate change, the interactions between fluvial morphodynamics and riparian vegetation may depend in part on the sequence of flood events. This paper describes a laboratory study of the geomorphic adjustment of a braided river to sequences of floods across five different strengths of braidplain vegetation. By using alfalfa as a proxy for braidplain vegetation, the differing plant life stages were used to represent the varying strengths of biogeomorphic feedbacks across the floods. Boundary conditions were constrained by sets of experimental runs with both equilibrium sediment loads and deficit loads. Changes in bed topography were monitored and assessed using a detailed digital elevation model, digital imagery and continuous monitoring of the transported sediment. Results demonstrate that in absence of plant colonization, vegetation placed the rivers in a non-equilibrium condition, in which riparian vegetation encouraged the development of new channels, increased the system channel width and enhanced topographic irregularity, these effects being more noticeable during the low-flow periods. The morphodynamics was found to be less sensitive to variations in flood discharges as the vegetation influence (strength) increased from minimum to maximum, until vegetation began to die back and the impacts of flood sequences became yet again evident. Although the overall sediment transport rate was reduced under full-grown vegetation conditions, the presence of the mature plants across the braid bars resulted in the greatest channel scour depths. Results are considered in light of expected changes in flood frequency with climate and likely morphodynamic responses of river systems as a result.     

Relationship between the equilibrium morphology of river islands and flow-sediment dynamics based on the theory of minimum energy dissipation

River islands are vital geomorphic units in alluvial rivers, and the variation of their morphology and position plays a significant role in regulating flow-sediment transport and channel stability. Based on the theories of minimum energy dissipation theory of fluid movement and river morphodynamics, this study uses the river islands in anabranching channels to analyze the relationship between the shape coefficient of river island and the flow-sediment dynamics under stable equilibrium conditions...     

Response of A Gravel - Bed River To Dam Closure: Insights From Sediment Transport Processes And Channel Morphodynamics

This work deals with the impacts of dams on large gravel -bed rivers in terms of altering coarse transport regimes and the relationship with river morphodynamics. Using data collected by a tracer -based monitoring programme carried out in a 4 -km -long study sector of the Parma River (Italy), located downstream from a relatively recently established dam, we applied a virtual velocity approach to estimate the coarse bed material load at four river cross -sections. Monitoring and calculation results provided new insights into the impacts of the dam on streambed material mobility and the sediment regime over the 17 -month calculation period. A longitudinal gradient of effects was observed along the study sector. Sections located closer to the dam are characterized by more evident impacts due to deficits in coarse sediment input from upstream. Sediment mobility here is strongly altered, especially in the highly armoured main channel, and the overall bed material load is extremely low. A partial recovery of sediment dynamics was observed at the sections located further from the dam, where estimates indicate higher sediment yield. The observed longitudinal trend in the coarse sediment transport regime matches the morphology, as the river shifts downstream from a sinuous configuration with alternate bars to a wandering one. The novel insights into alteration of coarse sediment dynamics and the relationship with river morphodynamics are potentially applicable to many other fluvial contexts affected by similar impoundments. © 2019 John Wiley & Sons, Ltd.     

Controls of alluvial cover formation,morphology and bedload transport in a sinuous channel with a non-alluvial boundary

The alluvial cover in channels with non-alluvial beds is a major morphologic feature in these rivers and has important geomorphic and ecologic functions. Although controls on the extent of the alluvial cover have been previously researched, little is known about the role of channel meanders in shaping the three-dimensional morphology and bedload transport rates in these rivers. Flume experiments were conducted in a fixed-bed sinuous channel scaled from an engineered urban river. A fully graded sediment supply mixture was fed into the bare channel at rates ranging between 0.3 and 1.2 times the estimated channel capacity under constant discharge. The three-dimensional morphology and surface texture of the alluvial cover were captured using photogrammetry, and the sediment output was periodically measured and sieved. A stable alluvial cover was achieved under all sediment supply conditions that coincided with a sediment transport equilibrium. The sediment supply rate controlled the final areal extent, mass and volume of the alluvial cover, while cover developed as a periodic series of stable bars ‘fixed’ by the channel planform. The alluvial cover development followed consistent trajectories relative to angular position around bends but developed to a greater degree and higher elevation with increasing sediment supply. The stable cover extent had a logarithmic relationship with the relative sediment supply, while the final mass, volume and bar height had linear relationships. The final channel morphology was characterized by fine-textured point bars with flat tops and steep margins connected by coarse riffle features. The outside of banks between bend apexes remained bare, even at sediment supply conditions exceeding the channel capacity. The length of the exposed outer banks followed predictable linear relationships with the total cover extent. Insights from this study can provide guidance for the management of channels with non-alluvial boundaries and provide validation for models of sinuous bedrock channel abrasion. © 2020 John Wiley & Sons, Ltd.     

The contribution of aeolian processes to fluvial sediment yield from a desert watershed in the Ordos Plateau,China

In arid zones, many active aeolian dunes terminate at ephemeral and perennial desert rivers. The desert rivers show very high rates of sediment transport that cause deleterious downstream effects on the river system and ecology. High sediment loading has been attributed to severe water erosion of sparsely covered watersheds during infrequent but heavy rainfall. Although aeolian erosion is known to lead to high rates of wind‐blown sand transport, direct confirmation of whether the aeolian processes accelerate or inhibit fluvial sediment loss is lacking. Here, we show that an aeolian‐fluvial cycling process is responsible for the high rate of suspended sediment transport in a Sudalaer ephemeral desert channel in the Ordos Plateau of China. Frequent aeolian processes, but low frequency (once every 3 years on average) flooding, occur in this region. Wind‐blown saltating grains appeared to be unable to cross the desert channel because of interruption of channel‐induced recirculating air flow, and therefore tended to settle in the channel during the windy seasons, leading to channel narrowing. During flooding, this narrowed channel was found to yield a threefold increase in suspended sediment loading and a 3.4‐fold increase in the weight percentage of the 0.08–0.2 mm sediment fraction on 18 July 2012. Loss of stored aeolian sand due to channel erosion accounted for about half of the total sediment yield in this watershed. These findings show that aeolian processes play an essential role in accelerating the sediment yield from a watershed characterized by aeolian‐fluvial interplay and also suggest that the drier the region and the greater the aeolian process, the more the aeolian process contributes to fluvial sediment yield. Copyright © 2013 John Wiley & Sons, Ltd.     

A coupled hierarchical modeling approach to simulating the geomorphic response of river systems to anthropogenic climate change

Anthropogenic climate change is expected to change the discharge and sediment transport regime of river systems. Because rivers adjust their channels to accommodate their typical inputs of water and sediment, changes in these variables can potentially alter river morphology. In this study, a hierarchical modeling approach was developed and applied to examine potential changes in reach‐averaged bedload transport and spatial patterns of erosion and deposition for three snowmelt‐dominated gravel‐bed rivers in the interior Pacific Northwest. The modeling hierarchy was based on discharge and suspended‐sediment load from a basin‐scale hydrologic model driven by a range of downscaled climate‐change scenarios. In the field, channel morphology and sediment grain‐size data for all three rivers were collected. Changes in reach‐averaged bedload transport were estimated using the Bedload Assessment of Gravel‐bedded Streams (BAGS) software, and the Cellular Automaton Evolutionary Slope and River (CAESAR) model was used to simulate the spatial pattern of erosion and deposition within each reach to infer potential changes in channel geometry and planform. The duration of critical discharge was found to control bedload transport. Changes in channel geometry were simulated for the two higher‐energy river reaches, but no significant morphological changes were found for a lower‐energy reach with steep, cohesive banks. Changes in sediment transport and river morphology resulting from climate change could affect the management of river systems for human and ecological uses. Copyright © 2015 John Wiley & Sons, Ltd.     

Least action principle,equilibrium states,iterative adjustment and the stability of alluvial channels

The energy based least action principle (LAP) has proven to be very successful for explaining natural phenomena in both classical and modern physics. This paper briefly reviews its historical development and details how, in three ways, it governs the behaviour and stability of alluvial rivers. First, the LAP embodies the special stationary equilibrium state of motion and so its incorporation with the principle of energy conservation explains why so many optimizing hypotheses have been proposed in fluvial geomorphology. Second, the variational approach underlying the LAP provides a more straightforward and simpler fuzzy‐object orientated method for solving river regime problems than do the various complex Newtonian formulations. Third, it is shown that in fluvial systems with surplus energy the surplus can be expended with slope and/or channel geometry adjustments, with the degree of channel geometry adjustment quantified by the dimensionless numbers F for depth dominated adjustment and H for width/depth dominated adjustment. Different planforms are preferred at different energy levels, with H providing a quantitative measure of the flow's efficiency for moving sediment. In rivers with insufficient energy, the interactions of endogenous and exogenous factors are shown to be capable, in certain circumstances, of achieving a stationary equilibrium condition which acts as the attractor state. Importantly, this study describes how iterative changes enable systems to achieve such a stable equilibrium. Copyright © 2007 John Wiley & Sons, Ltd.     

Monitoring and predicting channel change in a free‐evolving,small Alpine river: Ridanna Creek (North East Italy)

The recent (25 years) morphodynamics of a proglacial reach of the Ridanna Creek, North‐East Italy, evolving in the absence of human constraints, has been investigated by means of an intensive field activity and of the analysis of aerial photographs. The study reach mostly displays a braided morphology, with sharp downstream variations of valley gradient, sediment size and formative conditions within the main channel. These discontinuities are associated with different processes of channel adjustment at different timescales, which have been quantified by coupling hydrological with morphological information. Several processes of channel change and variations in braiding intensity have been documented along the whole reach and highlight how a regular, weakly meandering main channel may significantly affect the morphodynamics of the braided network. A first attempt to predict the morphological instability of this main channel at the observed spatial scales through existing linear theories of curved river channels shows a good agreement with field observations. Finally, the complete hydro‐morphodynamical characterization of such an undisturbed alpine river reach can provide a relevant contribution to the definition of reference conditions for Alpine rivers required by the EU Water Framework Directive. Copyright © 2007 John Wiley & Sons, Ltd.     

The influence of sediment supply on the channel morphology of upland streams: Howgill Fells,Northwest England

Previous work on stream channels in upland areas of Britain has demonstrated a close control over channel morphology and stability by the rate of coarse sediment supply from the hillslopes of the catchment. Streams fed by large amounts of coarse sediment develop unstable, wide, often braided channels, whereas those with limited coarse sediment supply develop stable, much narrower, often meandering channels. The sediment supply from hillslopes is controlled by thresholds of hillslope stability, storm event frequency, and the coupling between the hillslopes and the channel. Climatically-induced changes in any of these three factors may have implications for channel morphology and stability. This paper examines these implications in British upland fluvial systems, with particular reference to the Howgill Fells, Cumbria, in the contexts of the adjustment of stream channels to sediment supply from erosional gully systems, and their response to and recovery from major flood events.     

SEDIMENT-REMOVING CAPACITY AND RIVER MOTION DYNAMICS

l INTRODUCTIONT'he landscaPe is mainly shaPed by surface runoff of water through erosion and sedimentahon. mverflows cut the bed, scour the banks and silt the seas. All these are realized by moving sediment frOm oneplace to other places. The caPacity of the flow to remove sediment frOm one place to other places within ariver chanel is called sediment-removing caPacity. It differs frOm the well-defined sediment-capingcapacity For instance, steady flow carries sediment through the river …     

Multiple temporal scale relationships of bankfull discharge with streamflow and sediment transport in the Yellow River in China

This paper presents a study on the characteristics of multiple time scales of bankfull discharge and its delayed response to changes of flow conditions using continuous wavelet analysis for data from selected hydrological stations in the Yellow River basin. Results showed that bankfull discharge series had one or two dominant time scales. For example, the Huayuankou station in the lower reach of the Yellow River had two dominant time scales of 19-20 years and 545 years. The dominant time scales of the bankfull discharge series were generally consistent with the dominant time scales of water discharge and sediment concentration series, indicating that the channel morphology inherits the characteristics of the hydrological system in terms of multiple time scales. In addition, the wavelet coefficients of the bankfull discharge series had a phase difference in relation to those of the sediment concentration series, with a delay time that varied from 3 to 16 years at different sites. This delay time or relaxation time is a result of the delayed response of bankfull discharge to flow conditions, which was significant for channel adjustments in response to changes of flow conditions. The findings of the multiple time scales and the delayed response are of importance for further study of channel morphology of fluvial systems.     

Hydro‐morphodynamic evolution in a 90° movable bed discordant confluence with low discharge ratio

Confluences with low discharge and momentum ratios, where narrow steep tributaries with high sediment load join a wide low‐gradient main channel that provides the main discharge, are often observed in high mountain regions such as in the upper‐Rhone river catchment in Switzerland. Few existing studies have examined the hydro‐morphodynamics of this type of river confluence while considering sediment discharge in both confluent channels. This paper presents the evolution of the bed morphology and hydrodynamics as observed in an experimental facility with a movable bed. For that purpose, one experiment was carried out in a laboratory confluence with low discharge and momentum ratios, where constant sediment rates were supplied to both flumes. During the experiment, bed topography and water surface elevations were systematically recorded. When the bed topography reached a steady state (so‐called equilibrium) and the outgoing sediment rate approximated the incoming rate, flow velocity was measured at 12 different points distributed throughout the confluence, and the grain size distribution of the bed surface was analyzed. Typical morphodynamic features of discordant confluences such as a bank‐attached bar and a flow deflection zone are identified in this study. Nevertheless, the presence of a marked scour hole in the discordant confluence and distinct flow regimes for the tributary and main channel, differ from results obtained in previous studies. Strong acceleration of the flow along the outer bank of the main channel is responsible for the scour hole. This erosion is facilitated by the sediment discharge into the confluence from the main channel which inhibits bed armoring in this region. The supercritical flow regime observed in the tributary is the hydrodynamic response to the imposed sediment rate in the tributary. Copyright © 2015 John Wiley & Sons, Ltd.     

Channel adjustments of the lower Trinity River,Texas, downstream of Livingston Dam

Channel cross‐sectional changes since construction of Livingston Dam and Lake Livingston in 1968 were studied in the lower Trinity River, Texas, to test theoretical models of channel adjustment, and to determine controls on the spatial extent of channel response. High and average flows were not significantly modified by the dam, but sediment transport is greatly reduced. The study is treated as an opportunistic experiment to examine the effects of a reduction in sediment supply when discharge regime is unchanged. Channel scour is evident for about 60 km downstream, and the general phenomena of incision, widening, coarsening of channel sediment and a decrease in channel slope are successfully predicted, in a qualitative sense, by standard models of channel response. However, there is no consistent channel response within this reach, as various qualitatively different combinations of increases, decreases or no change in width, depth, slope and roughness occur. These multiple modes of adjustment are predicted by the unstable hydraulic geometry model. Between about 60 km and the Trinity delta 175 km downstream of the dam, no morphological response to the dam is observed. Rather than a diminution of the dam's effects on fluvial processes, this is due to a fundamental change in controls of the fluvial system. The downstream end of the scour zone corresponds to the upstream extent of channel response to Holocene sea level rise. Beyond 60 km downstream, the Trinity River is characterized by extensive sediment storage and reduced conveyance capacity, so that even after dam construction sediment supply still exceeds transport capacity. The channel bed of much of this reach is near or below sea level, so that sea level rise and backwater effects from the estuary are more important controls on the fluvial system than upstream inputs. Copyright © 2005 John Wiley & Sons, Ltd.     

Active channel width as a proxy of sediment supply from mining sites in New Caledonia

Although the channel morphology of upland fluvial systems is known to be strongly controlled by sediment supply from hillslopes, it is still difficult to isolate this effect from the other controlling factors of channel forms, such as the sediment transport capacity (depending notably on the size of the catchment) and local conditions (e.g. confinement, riparian vegetation, valley-floor slope). The rivers in New Caledonia offer an interesting field laboratory to isolate the morphological effect of contrasted sediment supply conditions. Some of these rivers are known to be highly impacted by the coarse sediment waves induced by the mining of nickel deposits that started in the early 1870s, which was particularly intensive between the 1940s and 1970s. The propagation of the sediment pulses from the mining sites can be traced by the presence of wide and aggraded active channels along the stream network of nickel-rich peridotite massifs. A first set of 63 undisturbed catchments in peridotite massifs distributed across the Grande Terre was used to fit a classic scaling law between active channel width and drainage area. A second set of 86 impacted sites, where the presence of sediment waves was clearly attested by recent aerial imagery, showed systematically wider active channels, with a width ratio around 5 (established from the intercept ratio of width–area power laws). More importantly, this second set of disturbed sites confirmed that the residual of active channel widths, computed from the scaling law of undisturbed sites, is statistically positively related to the catchment-scale relative area of major mining sediment sources. It is therefore confirmed that the characterization of sediment supply conditions is crucial for the understanding of spatial patterns of active channel width, and this should be more thoroughly considered in morphological studies of rivers draining environments with contrasted geomorphic activities on hillslopes. © 2018 John Wiley & Sons, Ltd.     

Long-term morphological river response to hydrological changes

Hydrologic changes have a great impact on the long-term river morphology. The most common anthropic cause is the construction of dams, which often reduces both the discharge regime and sediment transport, producing a narrowing and degradation of the river bed. In this study we propose a simple, lumped morphodynamic model that describes fluvial cross-section dynamics consequent to changes in discharge and sediment transport induced by external factors. The model provides the temporal dynamics of the river width and bed quote. These dynamics result not to be trivial and can exhibit non monotonic behavior, with aggradations and degradations, and narrowing and widening. The model has been tested on real rivers using data obtained from field studies. The agreement between the outcomes and the data measured in the field works is always satisfactory.