Influence of Quaternary paleoclimate change on the permeability of the loess–paleosol sequence in the Loess Plateau,northern China

Permeability differences in multi-cycle loess–paleosol aeolian sediments, which are still poorly understood, have the potential to significantly improve our understanding of climatic change during the glacial–interglacial periods of the Quaternary. In this study, the permeability of a well-preserved and continuous loess–paleosol sequence in the South Jingyang Plateau was investigated. Weathering intensity was inferred using a series of climate proxies including grain-size distribution, magnetic susceptibility and mineralogy. The results of laboratory tests showed that the average saturated hydraulic conductivity of loess layers is higher than that of paleosol layers. Also, clear differences between loess and paleosol were found in terms of depth variations of the vertical and horizontal saturated hydraulic conductivities. Differences in loess–paleosol were also found for other proxies for pedogenic weathering [i.e. clay content, sand content, Kd value (ratio of coarse silt to clay), magnetic susceptibility, dolomite content and the ratios of hornblende/illite and hornblende/chlorite]. Our results showed a high permeability of loess layers associated with weak pedogenic weathering during cold/dry paleoclimatic conditions in glacial stages. On the contrary, paleosol layers developed in a warm/humid climate during the interglacial stages experienced strong pedogenic weathering that resulted in lower permeability. Based on these results, we construct a connection between Quaternary climate change theory and the modern hydrological system. This provides a scientific basis for investigating the distribution and pollution of groundwater resources in the local region. © 2020 John Wiley & Sons, Ltd.     

The occurrence of a grassy vegetation over the Chinese Loess Plateau since the last interglacier: the molecular fossil record

A series of allochthonous and autochthonous molecular fossils were identified from the Holocene paleosol (S₀), Malan Loess and the top Lishi Loess (S₁) in Jiuzhoutai loess profile in Lanzhou through the GC/MS analysis. The allochthonous molecules were transported into the Plateau by the loess grains whilst the autochthonous molecules were related to the input of the local paleo-vegetation and could be used to reconstruct the paleo-vegetation. The distribution of the autochthonous n-alkanes was discriminated from the overlapping allochthonous homologues characterized by the CPI value of unity. The dominance of autochthonous C₃₁ n-alkane implicates the occurrence of a grassy vegetation over the Loess Plateau since the last interglacier. The warmest period of the Holocene, though dominated by grass, was additionally characterized by the relatively increased abundance of C₂₇ n-alkane indicative of woody plants. The desert plants might occur during the last glacier. The molecular fossil record is not contradictory with the recent phytolith data, denying the occurrence of a forest over the Plateau since the last interglacier. These data from the loess molecular stratigraphy indicate the importance of the discrimination of the autochthonous molecules from the allochthonous compounds.     

Carbon isotopic composition of modern soil and paleosol as a response to vegetation change on the Chinese Loess Plateau

The relationship between the carbon isotopic composition of paleosols and pale-ovegetation on the Loess Plateau is still unclear. One of the main reasons is that we are short of knowledge about the characteristics of the carbon isotopic composition of modern soil in this area. A preliminary investigation of the carbon isotopic compositions of the modern soil and the loess/paleosol sequence on the Loess Plateau shows that the carbon isotopic composition of modern soil is consistent with the distribution of modern plants on the Loess Plateau, where the ecosystem is dominated by a mixture of C4 and C3 plants. Comparing the δ13C values of modern soil and loess-paleosol sequences from the Xunyi profile, we conclude that C3 plants dominated the landscape during loess sediment stages, while C4 plants expanded during paleosol stages.     

Rock magnetic properties of a loess-paleosol couple along an N-S transect in the Chinese Loess Plateau

We have conducted detailed rock magnetic experiments on samples from loess unit 8 (L8) and paleosol unit 8 (S8) in Jingbian, Yichuan and Duanjiapo loess sections along an N-S transect in the Chinese Loess Plateau. Major rock magnetic results are as follows: (i) An increase of high field susceptibility (χ_h) in the same level of loess or paleosol from north to south is observed, suggesting an enhancement of pedogenesis. (ii) The low field susceptibility(χL) in loess unit L8 is almost the same in three sections. In contrast, the χ_L of paleosol unit S8 in Yichuan is highest, and the χ_L of Duanjiapo is lower than that in Yichuan section, suggesting that there is not correlation between the χ_L and the degree of pedogenesis in loess-paleosols. (iii) With the increasing of χ_L, both the contents of the superparamagnetic (SP) and the ferrimagnetic grains in loess-paleosol increase, however, the enhancement of magnetic susceptibility is probably dependent more on the increase of the ferrimagnetic concentration than on a change in the grain size. (iv) The content of the maghemite in loess unit 8 increases from the northern to the southern part of the Chinese Loess Plateau, and is positively correlated with the pedogenesis of the loess.     

Seasonal variations in infiltrability of moss‐dominated biocrusts on aeolian sand and loess soil in the Chinese Loess Plateau

Biocrust effects on soil infiltration have attracted increasing attention in dryland ecosystems, but their seasonal variations in infiltrability have not yet been well understood. On the Chinese Loess Plateau, soil infiltrability indicated by saturated hydraulic conductivity (K_s) of biocrusts and bare soil, both on aeolian sand and loess soil, was determined by disc infiltrometer in late spring (SPR), midsummer (SUM), and early fall (FAL). Then their correlations with soil biological and physiochemical properties and water repellency index (RI) were analysed. The results showed that the biocrusts significantly decreased K_s both on sand during SPR, SUM, and FAL (by 43%, 66%, and 35%, respectively; P < .05) and on loess (by 42%, 92%, and 10%, respectively; P <.05). As compared with the bare soil, the decreased K_s in the biocrusted surfaces was mostly attributed to the microorganism biomass and also to the increasing content of fine particles and organic matter. Most importantly, both the biocrusts and bare soil exhibited significant (F ≥ 11.89, P ≤ .003) seasonal variations in K_s, but their patterns were quite different. Specifically, the K_s of bare soil gradually decreased from SPR to SUM (32% and 42% for sand and loess, respectively) and FAL (29% and 39%); the K_s of biocrusts also decreased from SPR to SUM (59% and 92%) but then increased in FAL (36% and 588%). Whereas the seasonal variations in K_s of the biocrusts were closely correlated with the seasonal variations in RI, the RI values were not high enough to point at hydrophobicity. Instead of that, the seasonal variations of K_s were principally explained by the changes in the crust biomass and possibly by the microbial exopolysaccharides. We conclude that the biocrusts significantly decreased soil infiltrability and exhibited a different seasonal variation pattern, which should be carefully considered in future analyses of hydropedological processes.     

Feasibility of grain-size analysis methods for determination of vertical hydraulic conductivity of streambeds

Accurate estimation of streambed vertical hydraulic conductivity (K_v) is of great importance in the analysis of water quantity exchange and solute transfer between a stream and its sediments. The paper analyzed the inaccuracy of hydraulic conductivity values of sediments derived from grain-size distribution (K_g), which were determined from eight empirical grain-size methods to represent streambed K_v. In this study, the values of K_v for a streambed were derived using falling-head standpipe permeameter tests conducted at eight study sites in the Elkhorn River, Nebraska, and the tested streambed columns were then collected for grain-size analysis by sieving. These empirical methods were used to calculate the K_g values of the streambed from grain-size distribution data of sediments. Unlike many other studies, this study verifies K_g from grain-size distribution with K_v from permeameter tests on the basis of the same samples of streambed sediments. The K_g values derived from the eight empirical methods were larger than the K_v from permeameter tests; there are five methods that give K_g values of about 3–6 times larger than these K_v. The K_g values from the Kozeny formula followed by the Hazen formula give the largest overestimation error if they are used to represent the K_v of the streambed. The USBR and Shepherd formulas generated K_g values close to K_v, but these K_g values are still larger in general than the K_v values. Moreover, the new values of coefficient C for the empirical formulas were revised so that they can be used to calculate the approximate K_v of a streambed. Among the eight methods, the ratios of the original C values to the average new C range from 1.3 to 5.9. It can be hypothesized that smaller C values must be used in the estimation of K_v for general soil samples if these empirical formulas are used to calculate K_v.     

A Tube Seepage Meter for In Situ Measurement of Seepage Rate and Groundwater Sampling

We designed and evaluated a “tube seepage meter” for point measurements of vertical seepage rates (q), collecting groundwater samples, and estimating vertical hydraulic conductivity (K) in streambeds. Laboratory testing in artificial streambeds show that seepage rates from the tube seepage meter agreed well with expected values. Results of field testing of the tube seepage meter in a sandy‐bottom stream with a mean seepage rate of about 0.5 m/day agreed well with Darcian estimates (vertical hydraulic conductivity times head gradient) when averaged over multiple measurements. The uncertainties in q and K were evaluated with a Monte Carlo method and are typically 20% and 60%, respectively, for field data, and depend on the magnitude of the hydraulic gradient and the uncertainty in head measurements. The primary advantages of the tube seepage meter are its small footprint, concurrent and colocated assessments of q and K, and that it can also be configured as a self‐purging groundwater‐sampling device.     

Mineral magnetic variation of the Jingbian loess/paleosol sequence in the northern Loess Plateau of China: Implications for Quaternary development of Asian aridification and cooling

A high-resolution mineral magnetic investigation has been carried out on the Jingbian loess/paleosol sequence at the northern extremity of the Chinese Loess Plateau. Results show that the magnetic assemblage is dominated by large pseudo-single domain and multidomain-like magnetite with associated maghemite and hematite. Variations in the ratios of SIRM_100mT/SIRM, SIRM_100mT/SIRM_30mT and SIRM_100mT/SIRM_60mT (SIRM is the saturation isothermal remanent magnetization; SIRM_nmT represents the residual SIRM after an n mT alternating field demagnetization) have been used to document regional paleoclimate change in the Asian interior by correlating the mineral magnetic record with the composite δ¹⁸O record in deep-sea sediments. The long-term up-section decreasing trend in those ratios in both loess and paleosol units has been attributed to a long-term decrease in the relative contributions of eolian hematite during glacial extrema and of pedogenic hematite during interglacial extrema, respectively, which reveals a long-term decreasing trend in chemical weathering intensity in both glacial-stage source region (the Gobi and deserts in northwestern China) and interglacial-stage depositional area (the Loess Plateau region). We further relate this long-timescale variation to long-term increasing aridification and cooling, during both glacial extrema in the dust source region and interglacial extrema in the depositional area, over the Quaternary period. Changes in those ratios are most likely due to Quaternary aridification and cooling driven by ongoing global cooling, expansion of the Arctic ice-sheet, and progressive uplift of the Himalayan–Tibetan complex during this period.     

Anisotropy and depth‐related heterogeneity of hydraulic conductivity in a bog peat. I: laboratory measurements

Anisotropy and heterogeneity of hydraulic conductivity (K) are suspected of greatly affecting rates and patterns of ground‐water seepage in peats. A new laboratory method, termed here the modified cube method, was used to measure horizontal and vertical hydraulic conductivity (K_h and K_v) of 400 samples of bog peat. The new method avoids many of the problems associated with existing field and laboratory methods, and is shown to give relatively precise measurements of K. In the majority of samples tested, K_h was much greater than K_v, indicating that the bog peat was strongly anisotropic. Log₁₀K_h, log₁₀K_v, and log₁₀ (K_h/K_v) were found to vary significantly with depth, although none of the relationships was simple. We comment on the scale dependency of our measurements. Copyright © 2002 John Wiley & Sons, Ltd.     

Impacts of post-depositional processes on rapid monsoon signals recorded by the last glacial loess deposits of northern China

Rapid East Asian Monsoon oscillations recorded by Chinese loess are thought to be dynamically linked to north Atlantic climate. However, few efforts have been made to assess the effects of post-depositional processes (e.g., surface mixing and pedogenesis) on loess paleoclimatic records. Here a detailed optically stimulated luminescence dating of a thick loess sequence from the western Loess Plateau is presented, offering a reliable chronology for last glacial deposits. Magnetic susceptibility and mean grain size records from three loess–paleosol sequences along a northwest–southeast transect are investigated to evaluate impacts of post-depositional processes on these loess-based proxy records. Our results indicate that: (1) loess sequences developed within the flat tableland of the central and western Loess Plateau are nearly continuous during the last glaciation; and (2) post-depositional processes have distinct impacts on rapid monsoon signals recorded in loess sequences from different regions. In the central Loess Plateau, rapid monsoon signals have been attenuated to various degrees depending on the sedimentation rate and pedogenic intensity. In the northwestern Loess Plateau, however, due to high sedimentation rate and relatively weak pedogenesis, high-resolution grain size oscillations reliably record rapid monsoon changes and can be well correlated to rapid climate changes recorded in the Greenland ice core and Hulu cave stalagmite.     

Hydraulic Conductivity Calibration of Logging NMR in a Granite Aquifer,Laramie Range,Wyoming

In granite aquifers, fractures can provide both storage volume and conduits for groundwater. Characterization of fracture hydraulic conductivity (K) in such aquifers is important for predicting flow rate and calibrating models. Nuclear magnetic resonance (NMR) well logging is a method to quickly obtain near-borehole hydraulic conductivity (i.e., K_NMR) at high-vertical resolution. On the other hand, FLUTe flexible liner technology can produce a K profile at comparable resolution but requires a fluid driving force between borehole and formation. For three boreholes completed in a fractured granite, we jointly interpreted logging NMR data and FLUTe K estimates to calibrate an empirical equation for translating borehole NMR data to K estimates. For over 90% of the depth intervals investigated from these boreholes, the estimated K_NMR are within one order of magnitude of K_FLUTe. The empirical parameters obtained from calibrating the NMR data suggest that “intermediate diffusion” and/or “slow diffusion” during the NMR relaxation time may occur in the flowing fractures when hydraulic aperture are sufficiently large. For each borehole, “intermediate diffusion” dominates the relaxation time, therefore assuming “fast diffusion” in the interpretation of NMR data from fractured rock may lead to inaccurate K_NMR estimates. We also compare calibrations using inexpensive slug tests that suggest reliable K_NMR estimates for fractured rock may be achieved using limited calibration against borehole hydraulic measurements.     

Measuring streambank erosion due to ground water seepage: correlation to bank pore water pressure,precipitation and stream stage

Limited information exists on one of the mechanisms governing sediment input to streams: streambank erosion by ground water seepage. The objective of this research was to demonstrate the importance of streambank composition and stratigraphy in controlling seepage flow and to quantify correlation of seepage flow/erosion with precipitation, stream stage and soil pore water pressure. The streambank site was located in Northern Mississippi in the Goodwin Creek watershed. Soil samples from layers on the streambank face suggested less than an order of magnitude difference in vertical hydraulic conductivity (K_s) with depth, but differences between lateral K_s of a concretion layer and the vertical K_s of the underlying layers contributed to the propensity for lateral flow. Goodwin Creek seeps were not similar to other seeps reported in the literature, in that eroded sediment originated from layers underneath the primary seepage layer. Subsurface flow and sediment load, quantified using 50 cm wide collection pans, were dependent on the type of seep: intermittent low‐flow (LF) seeps (flow rates typically less than 0·05 L min^?1), persistent high‐flow (HF) seeps (average flow rate of 0·39 L min^?1) and buried seeps, which eroded unconsolidated bank material from previous bank failures. The timing of LF seeps correlated to river stage and precipitation. The HF seeps at Goodwin Creek began after rainfall events resulted in the adjacent streambank reaching near saturation (i.e. soil pore water pressures greater than ?5 kPa). Seep discharge from HF seeps reached a maximum of 1·0 L min^?1 and sediment concentrations commonly approached 100 g L^?1. Buried seeps were intermittent but exhibited the most significant erosion rates (738 g min^?1) and sediment concentrations (989 g L^?1). In cases where perched water table conditions exist and persistent HF seeps occur, seepage erosion and bank collapse of streambank sediment may be significant. Copyright © 2007 John Wiley & Sons, Ltd.     

Holocene climate changes in westerly-dominated areas of central Asia: Evidence from optical dating of two loess sections in Tianshan Mountain,China

Optical dating was applied to two loess-paleosol sections (Lujiaowan and Shuixigou) from the northern piedmont of Tianshan Mountain, Xinjiang province, China. The two sections are over 200 km apart and have a similar depositional sequence, which consists of two paleosol layers embedded by one loess layer. Two difficulties were met in optical dating. First, because the sections are located on the slope of the mountain, it was found that some cliff debris, with coarse grains (>200 μm), were mixed with the eolian sediments by rainfall, especially in the paleosol layers. Second, the optically stimulated luminescence (OSL) signals of quartz grains from the deposits were too dim to obtain a reliable equivalent dose (D_e). The 63–90 μm K-feldspar grains were separated to decrease the debris portion, and they yielded bright infrared stimulated luminescence (IRSL) signals. A multiple-elevated-temperature post-IR IRSL (MET-pIRIR) procedure was applied to determine D_e. Comparing the optical dating ages of the two sections, the Lujiaowan (LJW) and Shuixigou (SXG) sections recorded almost the same depositional process during the Holocene. The ages of the two loess layers (2.44–3.38 ka at LJW; 2.47–4.36 ka at SXG) suggested that one drought event happened widely in this westerly dominated area. The same drought event 2.5–3.5 ka ago also happened in the Chinese Loess Plateau (CLP), where the summer monsoon dominated. However, the paleosol development period (6.6–4 ka) in the study area was distinguished from the monsoon dominated area (8–4 ka), which suggests an arid early Holocene in the westerly area.     

Variation in soil saturated hydraulic conductivity along the hillslope of collapsing granite gullies

Saturated hydraulic conductivity (K_s) affects the soil hydrological process and is influenced by many factors that exhibit strong spatial variations. To accurately measure K_s and its scale, spatial variability and relationship with collapsing gullies, we analysed four double-ring infiltrometer diameters in three soil layers during in situ experiments designed to measure K_s in two typical collapsing gullies (three slope sites) in Tongcheng County of China. The results showed that K_s increased with increasing inner ring diameter, but no significant difference existed between inner diameters of 30 and 40 cm. The K_s in red soil layers was higher than that in sandy soil layers, the transition layers had the lowest values. K_s also varied with slope position, gradually decreasing with distance from the gully head. The suggestion is that the spatial variation in K_s is affected not only by the intrinsic soil properties but also by the interaction with the collapsing gully.     

Quantifying the surface covering,binding and bonding effects of biological soil crusts on soil detachment by overland flow

Biological soil crusts (BSCs) have impacts on soil detachment process through surface covering, and binding and bonding (B&B) mechanisms, which might vary with successional stages of BSCs. This study was conducted to quantify the effects of surface covering, binding and bonding of BSCs on soil detachment capacity by overland flow in a 4 m long hydraulic flume with fixed bed. Two dominant BSC types, developed well in the Loess Plateau (the early successional cyanobacteria and the later successional moss), were tested using natural undisturbed soil samples collected from the abandoned farmlands. Two treatments of undisturbed crusts and one treatment of removing the above‐ground tissue of BSCs were designed for each BSC type. For comparison, bare loess soil was used as the baseline. The collected soil samples were subjected to flow scouring under six different shear stresses, ranging from 6.7 to 21.2 Pa. The results showed that soil detachment capacity (D_c) and rill erodibility (K_r) decrease with BSC succession, and the presence of BSCs obviously increased the critical shear stress, especially for the later successional moss crust. For the early successional cyanobacteria crust, D_c was reduced by 69.2% compared to the bare loess soil, where 37.7% and 31.5% are attributed to the surface covering and B&B, respectively. For the later successional moss crust, D_c decreased by 89.8% compared to the bare loess soil, where 68.9% and 20.9% contributed to the surface covering and B&B, respectively. These results are helpful in understanding the influencing mechanism of BSCs on soil erosion and in developing the process‐based erosion models for grassland and forestland. Copyright © 2017 John Wiley & Sons, Ltd.     

An Integrated Laboratory Method to Measure and Verify Directional Hydraulic Conductivity in Fine‐to‐Medium Sandy Sediments

The constant‐head permeameter test (CHPT) is widely used in sandy samples as a standard method in the laboratory to investigate hydraulic conductivity (K). However, it neither can be used to consistently determine directional hydraulic conductivity (DHC) nor guarantee the comparability of measured K values of samples with different sizes. Therefore, this paper proposes an integrated laboratory method, called modified CHPT (MCHPT), for the efficient determination and verification of consistent DHC values in fine‐to‐medium sandy sediments, based on a new methodological framework. A precise and standardized procedure for preparing the experimental setup of MCHPT was conducted, based on the integrated experimental setup of CHPT and tracer tests. Moreover, a formula was yielded for the time‐optimized sample saturation control. In comparison with grain size‐based methods, the validity of consistent K_h and K_v values determined by MCHPT was convincing.     

Horizontal hydraulic conductivity of shallow streambed sediments and comparison with the grain‐size analysis results

Streambed horizontal hydraulic conductivity (K_h) has a substantial role in controlling exchanges between stream water and groundwater. We propose a new approach for determining K_h of the shallow streambed sediments. Undisturbed sediment samples were collected using tubes that were horizontally driven into streambeds. The sediment columns were analysed using a permeameter test (PT) on site. This new test approach minimizes uncertainties due to vertical flow in the vicinity of test tube and stream stage fluctuations in the computation of the K_h values. Ninety‐eight PTs using the new approach were conducted at eight sites in four tributaries of the Platte River, east‐central Nebraska, USA. The K_h values were compared with the nondirectional hydraulic conductivity values (K_g) determined from 12 empirical grain‐size analysis methods. The grain‐size analysis methods used the same sediment samples as K_h tests. Only two methods, the Terzaghi and Shepherd methods, yielded K_g values close to the K_h values. Although the Sauerbrei method produced a value relatively closer to K_h than other nine grain‐size analysis methods, the values from this method were not as reliable as the methods of Terzaghi and Shepherd due to the inconsistent fluctuation of the average estimates at each of the test sites. The Zunker, Zamarin, Hazen, Beyer, and Kozeny methods overestimated K_h, while the Slichter, US Bureau of Reclamation (USBR), Harleman, and Alyamani and Sen methods underestimated K_h. Any of these specific grain‐size methods might yield good estimates of streambed K_h at some sites, but give poor estimates at other sites, indicating that the relationship between K_g and K_h is significantly site dependent in our study. Copyright © 2011 John Wiley & Sons, Ltd.     

Depth‐dependent hydraulic conductivity distribution patterns of a streambed

Characterization of streambed hydraulic conductivity from the channel surface to a great depth below the channel surface can provide needed information for the determination of stream‐aquifer hydrologic connectedness, and it is also important to river restoration. However, knowledge on the streambed hydraulic conductivity for sediments 1 m below the channel surface is scarce. This study describes a method that was used to determine the distribution patterns of streambed hydraulic conductivity for sediments from channel surface to a depth of 15 m below. The method includes Geoprobe's direct‐push techniques and Permeameter tests. Direct‐push techniques were used to generate the electrical conductivity (EC) logs and to collect sequences of continuous sediment cores from river channels, as well as from the alluvial aquifer connected to the river. Permeameter tests on these sediment cores give the profiles of vertical hydraulic conductivity (K_v) of the channel sediments and the aquifer materials. This method was applied to produce K_v profiles for a streambed and an alluvial aquifer in the Platte River Valley of Nebraska, USA. Comparison and statistical analysis of the K_v profiles from the river channel and from the proximate alluvial aquifer indicates a special pattern of K_v in the channel sediments. This depth‐dependent pattern of K_v distribution for the channel sediments is considered to be produced by hyporheic processes. This K_v‐distribution pattern implied that the effect of hyporheic processes on streambed hydraulic conductivity can reach the sediments about 9 m below the channel surface. Copyright © 2010 John Wiley & Sons, Ltd.     

The response law of far-field seismic ground motion of the Wenchuan earthquake and its damaging mechanism in the Loess Plateau

A series of housing collapses and other serious damage was caused by the 2008 Wenchuan M_S 8.0 earthquake in the seismic intensity Ⅵ areas of the Loess Plateau, which is hundreds of kilometers away from the epicenter, and which showed a remarkable seismic intensity anomaly. The seismic disasters are closely related to the seismic response characteristics of the site, therefore, the systematic study of the far-field seismic response law of the Wenchuan earthquake in the Loess Plateau is of great significance to prevent the far-field disaster of great earthquake. In this paper, the seismic acceleration records of several bedrock stations and loess stations from the seismogenic fault of the Wenchuan earthquake to the Loess Plateau were collected, and the attenuation law of ground motion along the propagation path and the characteristics of seismic response on the loess site are studied, and the mechanism of amplification effect of ground motion is analyzed based on the dynamic feature parameters of the loess site obtained through the HVSR method. Taking a typical loess site of thick deposit as the prototype, a series of shaking table tests of dynamic response of loess site models with different thicknesses were carried out. Amplification effect, spectral characteristics of acceleration in model sites were analyzed under the action of a far-field seismic wave of the Wenchuan earthquake. The results show that seismic attenuation on the propagation path along the NE strike of the seismogenic fault to the Loess Plateau is slower than that in other directions, and the predominant period range of ground motion on bedrock site of the Loess Plateau presents broadband characteristics. Because the natural periods of loess sites with thick deposits are within the predominant period range of bedrock input wave, loess sites appear significant amplification effect of ground motion, the horizontal acceleration of ground motion exceeds 0.1 ?g, the seismic intensity reaches 7°. The thicker the loess deposit is, the more significant the change of spectral characteristics of ground motion on loess sites, and the narrower the predominant period range of ground motion becomes, and the closer it is to the natural period of loess sites. Therefore, for some old houses on thick loess sites, the poor seismic performance and strong seismic response eventually led to their collapses and damages because their natural periods are very close to the predominant period of ground motion of the Wenchuan earthquake on thick loess sites; For these damaged high-rise buildings, the resonance effect might be the main reason for their damages because their natural periods are included in the predominant period range of ground motion of the Wenchuan earthquake on thick loess sites.These research results would provide a basis for seismic disasters prediction and evaluation and seismic design of construction engineering in the Loess Plateau.     

黄土高原西北缘末次冰期晚期以来黄土沉积物的岩石磁学性质

以黄土高原西北缘的靖远和古浪剖面(包含黄土层L1上部和占土壤层SO)作为研究对象,选取代表性样品进行磁化率、频率磁化率、热磁曲线、等温剩磁获得曲线和磁滞回线等测定.结果表明,靖远和古浪L1黄土和SO古土壤具有相似的岩石磁学特征.磁性矿物含量相对较低,载磁矿物均以磁铁矿为主,同时含有磁赤铁矿和赤铁矿,且SO占土壤中的磁赤...