Deliniation of Weathering in the Çatalca Granite Quarry with the Very Low Frequency (VLF) Electromagnetic Method

Faulting and weathering can endanger quarry operations by decreasing the total reserve, quarry’s useful life and production value. We investigated weathering and faulting problems in the Çatalca granite quarry at Istanbul in Turkey, using the Very Low Frequency (VLF) method. VLF method is an electromagnetic method which is very successful in locating vertical discontinuities such as faults and fracture zones. This method measures the apparent resistivity of the rocks in the region, besides the electromagnetic parameters such as tilt angle and ellipcity. Apparent resistivity is a very sensitive parameter to water presence inside the pores and fractures of the rocks. This feature enables the VLF method to map the boundaries between the fresh and cracked granite and altered zones in the quarry. In this work we mapped the faults and weathered zones within the granite in Çatalca quarry and found a high resistivity zone at the central part of the survey area which may be suitable for production. This study also shows the efficiency of the VLF method in understanding the structural and textural features of a quarry and estimating zones with high quality rocks for production planning.     

Origin of honeycombs and related weathering forms in Oligocene Macigno Sandstone,Tuscan coast near Livorno,Italy

Two types of cavernous‐weathering features are exposed in the Oligocene Macigno Sandstone along 5 km of the Tuscan coast south of Livorno, Italy. Honeycomb cells (type 1 features) are typical closely spaced, more or less circular pits of centimetre scale that have been eroded 2 to 6 cm below the general surface of bedding planes or joints. ‘Aberrant honeycomb’ cells (type 2 features) are highly elongate, polygonal, or irregular ?at depressions of decimetre scale surrounded by walls rarely higher than 2 cm, some of which pass into long, free‐standing walls or tendrils. Thus, not all type 2 ‘honeycomb’ cells are fully enclosed. We measured the geometry of 551 honeycomb cells and examined various rock properties (microscopic texture and fabric, mineralogy, porosity, permeability, and chemical composition) to isolate factors that control the size, shape, distribution, and pattern of the honeycombs. Our goal was to narrow potential origins of the features and to understand their formation. The ubiquitous occurrence of sea salt in the honeycombs and scanning electron microscope evidence of physical weathering of silicates, especially micas, favours an origin for the honeycombs chie?y by salt weathering. Honeycombs do not form in siltstone, iron‐oxide‐impregnated sandstone, calcite‐cemented concretions, or in case‐hardened joints. Thus, salt weathering of type 1 and 2 honeycombs is not effective in very low permeability rocks. We propose for type 1 honeycombs that seawater is drawn into micropores of the sandstone and evolves into self‐organized diffusion cells (Turing patterns). Selective evaporation at the stationary nodes of diffusion cells, which form at the same site over time, leads to the precipitation of salt, then grains spall off, and pits are formed. The deepest pits (>40 mm) formed where Turing patterns consistently formed at the same sites. Although the walls are more porous and weathered than the host sandstone, they become selectively case hardened by an unidenti?ed component of low abundance. Initial honeycomb cell shape and gravity locally in?uenced type 1 honeycomb shapes. We suggest that type 2 honeycombs develop where diffusion‐controlled Turing patterns lead to case‐hardening along linear trends; gravity and rock fabric are important locally in in?uencing the orientation of the walls. Only type 2 cells are forming today, suggesting recent environmental changes. Gravity is not a fundamental control on honeycomb shape; in places it is a contributing factor. Pre‐existing depressions (quarry tool marks) have strongly in?uenced honeycomb shape locally. Copyright © 2004 John Wiley & Sons, Ltd.     

Biogenic origin of coastal honeycomb weathering

Honeycomb weathering occurs in two environments in Late Cretaceous and Eocene sandstone outcrops along the coastlines of south‐west Oregon and north‐west Washington, USA, and south‐west British Columbia, Canada. At these sites honeycomb weathering is found on subhorizontal rock surfaces in the intertidal zone, and on steep faces in the salt spray zone above the mean high tide level. In both environments, cavity development is initiated by salt weathering. In the intertidal zone, cavity shapes and sizes are primarily controlled by wetting/drying cycles, and the rate of development greatly diminishes when cavities reach a critical size where the amount of seawater left by receding tides is so great that evaporation no longer produces saturated solutions. Encrustations of algae or barnacles may also inhibit cavity enlargement. In the supratidal spray zone, honeycomb weathering results from a dynamic balance between the corrosive action of salt and the protective effects of endolithic microbes. Subtle environmental shifts may cause honeycomb cavity patterns to continue to develop, to become stable, or to coalesce to produce a barren surface. Cavity patterns produced by complex interactions between inorganic processes and biologic activity provide a geological model of ‘self‐organization’. Surface hardening is not a factor in honeycomb formation at these study sites. Salt weathering in coastal environments is an intermittently active process that requires particular wind and tidal conditions to provide a supply of salt water, and temperature and humidity conditions that cause evaporation. Under these conditions, salt residues may be detectable in honeycomb‐weathered rock, but absent at other times. Honeycomb weathering can form in only a few decades, but erosion rates are retarded in areas of the rock that contain cavity patterns relative to adjacent non‐honeycombed surfaces. Copyright © 2010 John Wiley & Sons, Ltd.     

Laboratory simulation of the salt weathering of schist: II. Fragmentation of fine schist particles

Recent developments in long term landform evolution modelling have created a new demand for quantitative salt weathering data, and in particular data describing the size distribution of the weathered rock fragments. To enable future development of rock breakdown models for use in landscape evolution and soil production models, laboratory work was undertaken to extend existing schist/salt weathering fragmentation studies to include an examination of the breakdown of sub‐millimetre quartz chlorite schist particles in a seasonally wet tropical climate. Laser particle sizing was used to assess the impact of different experimental procedures on the resulting particle size distribution. The results reveal that salt weathering under a range of realistic simulated tropical wet season conditions produces a significant degree of schist particle breakdown. The fragmentation of the schist is characterized by splitting of the larger fragments into mid‐sized product with finer material produced, possibly from the breakdown of mid‐sized fragments when weathering is more advanced. Salinity, the salt addition method and temperature were all found to affect weathering rates. Subtle differences in mineralogy also produce variations in weathering patterns and rates. It is also shown that an increase in drying temperature leads to accelerated weathering rates, however, the geometry of the fracture process is not significantly affected. Copyright © 2006 John Wiley & Sons, Ltd.     

Patterns of damage in igneous and sedimentary rocks under conditions simulating sea‐salt weathering

A saline‐spray artificial ageing test was used to simulate the effects produced in granites and sedimentary rocks (calcarenites, micrites and breccia) under conditions in coastal environments. Three main points were addressed in this study: the durability of the different kinds of rock to salt decay, the resulting weathering forms and the rock properties involved in the weathering processes. For this, mineralogical and textural characterization of each of the different rocks was carried out before and after the test. The soluble salt content at different depths from the exposed surfaces was also determined. Two different weathering mechanisms were observed in the granite and calcareous rocks. Physical processes were involved in the weathering of granite samples, whereas dissolution of calcite was also involved in the deterioration of the calcareous rocks. We also showed that microstructural characteristics (e.g. pore size distribution), play a key role in salt damage, because of their influence on saline solution transport and on the pressures developed within rocks during crystallization. Copyright © 2003 John Wiley & Sons, Ltd.     

The critical role of climate and saprolite weathering in landscape evolution

Landscapes evolve in response to external forces, such as tectonics and climate, that influence surface processes of erosion and weathering. Internal feedbacks between erosion and weathering also play an integral role in regulating the landscapes response. Our understanding of these internal and external feedbacks is limited to a handful of field‐based studies, only a few of which have explicitly examined saprolite weathering. Here, we report rates of erosion and weathering in saprolite and soil to quantify how climate influences denudation, by focusing on an elevation transect in the western Sierra Nevada Mountains, California. We use an adapted mass balance approach and couple soil‐production rates from the cosmogenic radionuclide (CRN) ¹⁰Be with zirconium concentrations in rock, saprolite and soil. Our approach includes deep saprolite weathering and suggests that previous studies may have underestimated denudation rates across similar landscapes. Along the studied climate gradient, chemical weathering rates peak at middle elevations (1200–2000 m), averaging 112·3 ± 9·7 t km^–2 y^–1 compared to high and low elevation sites (46·8 ± 5·2 t km^?2 y^?1). Measured weathering rates follow similar patterns with climate as those of predicted silica fluxes, modeled using an Arrhenius temperature relationship and a linear relationship between flux and precipitation. Furthermore, chemical weathering and erosion are tightly correlated across our sites, and physical erosion rates increase with both saprolite weathering rates and intensity. Unexpectedly, saprolite and soil weathering intensities are inversely related, such that more weathered saprolites are overlain by weakly weathered soils. These data quantify exciting links between climate, weathering and erosion, and together suggest that climate controls chemical weathering via temperature and moisture control on chemical reaction rates. Our results also suggest that saprolite weathering reduces bedrock coherence, leading to faster rates of soil transport that, in turn, decrease material residence times in the soil column and limit soil weathering. Copyright © 2009 John Wiley & Sons, Ltd.     

The influence of solar‐induced thermal stresses on the mechanical weathering of rocks in humid mid‐latitudes

The role of solar‐induced thermal stresses in the mechanical breakdown of rock in humid‐temperate climates has remained relatively unexplored. In contrast, numerous studies have demonstrated that cracks in rocks found in more arid mid‐latitude locations exhibit preferred northeast orientations that are interpreted to be a consequence of insolation‐related cracking. Here we hypothesize that similar insolation‐related mechanisms may be efficacious in humid temperate climates, possibly in conjunction with other mechanical weathering processes. To test this hypothesis, we collected rock and crack data from a total of 310 rocks at a forested field site in North Carolina (99 rocks, 266 cracks) and at forested and unforested field sites in Pennsylvania (211 rocks, 664 cracks) in the eastern United States. We find that overall, measured cracks exhibit statistically preferred strike orientations (47° ± 16), as well as dip angles (52° ± 24°), that are similar in most respects to comparable datasets from mid‐latitude deserts. There is less variance in strike orientations for larger cracks suggesting that cracks with certain orientations are preferentially propagated through time. We propose that diurnally repeating geometries of solar‐related stresses result in propagation of those cracks whose orientations are favorably oriented with respect to those stresses. We hypothesize that the result is an oriented rock heterogeneity that acts as a zone of weakness much like bedding or foliation that can, in turn, be exploited by other weathering processes. Observed crack orientations vary somewhat by location, consistent with this hypothesis given the different latitude and solar exposure of the field sites. Crack densities vary between field sites and are generally higher on north‐facing boulder‐faces and in forested sites, suggesting that moisture‐availability also plays a role in dictating cracking rates. These data provide evidence that solar‐induced thermal stresses facilitate mechanical weathering in environments where other processes are also likely at play. Copyright © 2015 John Wiley & Sons, Ltd.     

Field evidence for the influence of weathering on rock erodibility and channel form in bedrock rivers

Erosion processes in bedrock‐floored rivers shape channel cross‐sectional geometry and the broader landscape. However, the influence of weathering on channel slope and geometry is not well understood. Weathering can produce variation in rock erodibility within channel cross‐sections. Recent numerical modeling results suggest that weathering may preferentially weaken rock on channel banks relative to the thalweg, strongly influencing channel form. Here, we present the first quantitative field study of differential weathering across channel cross‐sections. We hypothesize that average cross‐section erosion rate controls the magnitude of this contrast in weathering between the banks and the thalweg. Erosion rate, in turn, is moderated by the extent to which weathering processes increase bedrock erodibility. We test these hypotheses on tributaries to the Potomac River, Virginia, with inferred erosion rates from ~0.1 m/kyr to >0.8 m/kyr, with higher rates in knickpoints spawned by the migratory Great Falls knickzone. We selected nine channel cross‐sections on three tributaries spanning the full range of erosion rates, and at multiple flow heights we measured (1) rock compressive strength using a Schmidt hammer, (2) rock surface roughness using a contour gage combined with automated photograph analysis, and (3) crack density (crack length/area) at three cross‐sections on one channel. All cross‐sections showed significant (p < 0.01 for strength, p < 0.05 for roughness) increases in weathering by at least one metric with height above the thalweg. These results, assuming that the weathered state of rock is a proxy for erodibility, indicate that rock erodibility varies inversely with bedrock inundation frequency. Differences in weathering between the thalweg and the channel margins tend to decrease as inferred erosion rates increase, leading to variations in channel form related to the interplay of weathering and erosion rate. This observation is consistent with numerical modeling that predicts a strong influence of weathering‐related erodibility on channel morphology. Copyright © 2017 John Wiley & Sons, Ltd.     

The nature and pattern of debris liberation by salt weathering: A laboratory study

A laboratory simulation of salt weathering was used to ascertain the effects of sodium sulphate and sodium carbonate under ‘Negev’ conditions using a single immersion technique. Three main points were addressed: what are the grain size and textural characteristics of the debris liberated from limestones and a sandstone, what do scanning electron microscope observations of the weathered samples tell us about the decay processes involved, and how does the rate of debris liberation change during the course of 100 cycles? The grain size characteristics of the liberated debris tended to be multimodal and were related to the original petrological characteristics of the rock. Large amounts of fines were produced which are believed to be analogous to the ‘rock flour’ of arid areas. Blistering was also observed. Scanning electron microscope analysis revealed differences in the style of attack for different rock types and salt treatments, and revealed the pattern of salt crystallization in pores and the nature of cracking. The rate of debris liberation tended to decline or remain constant through time. The reasons for this remain obscure, but it is evident that diurnal cycles of temperature and humidity change can cause continuing rock weathering long after the initial input of salt to the rock has taken place.     

Weathering and erosion of fractured bedrock systems

We explore the contribution of fractures (joints) in controlling the rate of weathering advance for a low‐porosity rock by using methods of homogenization to create averaged weathering equations. The rate of advance of the weathering front can be expressed as the same rate observed in non‐fractured media (or in an individual block) divided by the volume fraction of non‐fractured blocks in the fractured parent material. In the model, the parent has fractures that are filled with a more porous material that contains only inert or completely weathered material. The low‐porosity rock weathers by reaction‐transport processes. As observed in field systems, the model shows that the weathering advance rate is greater for the fractured as compared to the analogous non‐fractured system because the volume fraction of blocks is < 1. The increase in advance rate is attributed both to the increase in weathered material that accompanies higher fracture density, and to the increase in exposure of surface of low‐porosity rock to reaction‐transport. For constant fracture aperture, the weathering advance rate increases when the fracture spacing decreases. Equations describing weathering advance rate are summarized in the ‘List of selected equations’. If erosion is imposed at a constant rate, the weathering systems with fracture‐bounded bedrock blocks attain a steady state. In the erosional transport‐limited regime, bedrock blocks no longer emerge at the air‐regolith boundary because they weather away. In the weathering‐limited (or kinetic) regime, blocks of various size become exhumed at the surface and the average size of these exposed blocks increases with the erosion rate. For convex hillslopes, the block size exposed at the surface increases downslope. This model can explain observations of exhumed rocks weathering in the Luquillo mountains of Puerto Rico. Published 2017. This article is a U.S. Government work and is in the public domain in the USA     

Weathering of granitic rocks by chlorides: effect of the nature of the solution on weathering morphology

Five granites from NW Spain were subjected to two salt‐spray weathering tests under controlled atmospheric conditions. Granite samples were exposed to a sodium chloride solution in the first test and to a complex solution (sea water) in the second. Subsequent examination of the rocks by light and petrographic microscopy clearly demonstrated the development of different weathering morphologies in each test. The distribution of dissolved ions in samples taken at different depths from the weathered surfaces at the end of the experiments, and the changes in weight of the samples during the tests, also differed. In our opinion, these results were determined by the nature of the solution used; although sodium chloride is the predominant salt in sea water, the presence of other ions modifies its solubility, thereby varying the dynamics of mobility and precipitation and thus the weathering morphology that develops. Copyright © 2003 John Wiley & Sons, Ltd.     

Element geochemistry of weathering profile of dolomitite and its implications for the average chemical composition of the upper-continental crust

Geochemical behavior of chemical elements is studied in a dolomitite weathering profile in upland of karst terrain in northern Guizhou. Two stages can be recognized during the process ofin situ weathering of dolomitite: the stage of sedentary accumulation of leaching residue of dolomitite and the stage of chemical weathering evolution of sedentary soil. Ni, Cr, Mo, W and Ti are the least mobile elements with reference to Al. The geochemical behavior of REE is similar to that observed in weathering of other types of rocks. Fractionation of REE is noticed during weathering, and the two layers of REE enrichments are thought to result from downward movement of the weathering front in response to changes in the environment. It is considered that the chemistry of the upper part of the profile, which was more intensively weathered, is representative of the mobile components of the upper curst at the time the dolomitite was formed, while the less weathered lower profile is chemically representative of the immobile constitution. Like glacial till and loess, the “insoluble” materials in carbonate rocks originating from chemical sedimentation may also provide valuable information about the average chemical composition of the upper continental crust.     

New challenges for tafoni research. A new approach to understand processes and weathering rates

Cavernous tafoni‐type weathering is a common and conspicuous global feature, creating artistic sculptures, which may be relevant for geochemical budgets. Weathering processes and rates are still a matter of discussion. Field evidence in the type locality Corsica revealed no trend of size variability from the coast to subalpine elevations and the aspect of tafoni seems to be governed primarily by the directions of local fault systems and cleavage, and only subordinately by wind directions or the aspect of insulation. REM analysis of fresh tafone chips confirmed mechanical weathering by the crystallization of salts, as conchoidal fracturing of quartz is observed. The salts are only subordinately provided by sea spray, as calcium and sodium sulfates rather than halite dominate even close to the coast. Characteristic element ratios compare well with aerosols from mixed African and European air masses. Sulfates are largely derived from Sahara dust, indicated by their sulfur isotopic composition. Salt crystals form by capillary rise within the rock and subsequent crystallization in micro‐cracks and at grain boundaries inside rain‐protected overhangs. Siderophile bacteria identified by raster electron microscopy (REM) analysis of tafone debris contribute to accelerated weathering of biotite and tiny sulfide ore minerals. By applying ¹⁰Be‐exposure dating, weathering rates of large mature tafone structures were found to be about an order of magnitude higher than those on the exposed top of the affected granite blocks. Copyright © 2010 John Wiley & Sons, Ltd.     

Laboratory simulation of the salt weathering of schist: 1. Weathering of schist blocks in a seasonally wet tropical environment

Data describing sediment generation focusing on the temporal evolution of size gradation are required for the prediction of long‐term landform evolution. This paper presents such data for the salt weathering of a quartz‐chlorite schist obtained from the Ranger Uranium Mine in northern Australia. Rock fragment samples are subjected to three different climate regimes: (1) a dry season climate; (2) a wet season climate (both based on observations at the Ranger site); and (3) an oven‐drying sequence designed to test the sensitivity of the weathering process by exposing the rocks to more extreme temperatures. Two MgSO₄ salt solutions are applied, one being typical of wet season runoff and the other a more concentrated solution. Salt solution is applied daily in the wet season experiments and once only at the beginning of the dry season experiments. Results of the experiments reveal four stages of weathering. The kinetics of each stage are described and related to the formation of sediment of different sizes. Wet season climate conditions are shown to produce greater moisture variability and lead to faster weathering rates. However, salt concentrations in the wet season are typically lower and so when climate is combined with observed salt concentrations, the dry and wet season experiments weather at approximately equal rates. Finally, small variations in rock properties were shown to have a large impact on weathering rates, leading to the conclusion that rock weathering experiments need to be carefully designed if results are to be used to help predict weathering behaviour at the landscape scale. Copyright © 2006 John Wiley & Sons, Ltd.     

Rock surface millimetre‐scale roughness and weathering of supratidal Mallorcan carbonate coasts (Balearic Islands)

Quantitative data on rock surface millimetre‐scale roughness are presented concerning the splash and spray geomorphologic domains of two coastal profiles developed on Mediterranean carbonate rocks. Differences of the roughness characteristics are attributed to rock properties, weathering agents and bioerosion. In the splash zone, roughness is related to sparsely distributed patterns of bioerosion, salt weathering and wave attack. In the spray zone, smooth surfaces seem to be the response to the solution processes that predominate, exerting a more homogenous influence on rock surface evolution. Copyright © 2006 John Wiley & Sons, Ltd.     

Weathering,erosion and sediment composition in a high‐gradient river,Calabria, Italy

Source rock lithology and immediate modifying processes, such as chemical weathering and mechanical erosion, are primary controls on fluvial sediment supply. Sand composition and Chemical Index of Alteration (CIA) of parent rocks, soil and fluvial sand of the Savuto River watershed, Calabria (Italy), were used to evaluate the modifications of source rocks through different sections of the basin, characterized by different geomorphic processes, in a sub‐humid Mediterranean climate. The headwaters, with gentle topography, produce a coarse‐grained sediment load derived from deeply weathered gneiss, having sand of quartzofeldspathic composition, compositionally very different from in situ degraded bedrock. Maximum estimated CIA values suggest that source rock has been affected significantly by weathering, and it testifies to a climatic threshold on the destruction of the bedrock. The mid‐course has steeper slopes and a deeply incised valley; bedrock consists of mica‐schist and phyllite with a very thin regolith, which provides large cobble to very coarse sand sediments to the main channel. Slope instability, with an areal incidence of over 40 per cent, largely supplies detritus to the main channel. Sand‐sized detritus of soil and fluvial sand is lithic. Estimated CIA value testifies to a significant weathering of the bedrock too, even if in this part of the drainage basin steeper slopes allow erosion to exceed chemical weathering. The lower course has a braided pattern and sediment load is coarse to medium–fine grained. The river cuts across Palaeozoic crystalline rocks and Miocene siliciclastic deposits. Sand‐sized detritus, contributed from these rocks and homogenized by transport processes, has been found in the quartzolithic distal samples. Field and laboratory evidence indicates that landscape development was the result of extensive weathering during the last postglacial temperature maximum in the headwaters, and of mass‐failure and fluvial erosional processes in the mid‐ and low course. Copyright © 2000 John Wiley & Sons, Ltd.     

A new technique for non‐destructive field measurement of rock‐surface strength: an application of the Equotip hardness tester to weathering studies

Tafone‐like depressions have developed on the Aoshima sandstone blocks used for a masonry bridge pier in the coastal spray zone. A thin layer of partial granular disintegration was found on the surface in depressions. To evaluate quantitatively the strength of the thin weathered layer, the hardness was measured at the surface of the sandstone blocks using both an Equotip hardness tester and an L‐type Schmidt hammer. Comparison of the two testing results indicates that the Equotip hardness value is more sensitive in evaluating the strength of a thin layer of weathered surface rock than the Schmidt hardness value. By applying two methods, i.e. both the repeated impact method and the single impact method, the Equotip tester can evaluate the strengths of fresh internal and weathered surficial portions of rocks having a thin weathering layer. Comparison of the two strengths enables evaluation of strength reduction due to weathering. Copyright © 2007 John Wiley & Sons, Ltd.     

Downvalley fining of hillslope sediment in an alpine catchment: implications for downstream fining of sediment flux in mountain rivers

The size distributions of sediment delivered from hillslopes to rivers profoundly influence river morphodynamics, including river incision into bedrock and the quality of aquatic habitat. Yet little is known about the factors that influence size distributions of sediment produced by weathering on hillslopes. We present results of a field study of hillslope sediment size distributions at Inyo Creek, a steep catchment in granitic bedrock of the Sierra Nevada, USA. Particles sampled near the base of hillslopes, adjacent to the trunk stream, show a pronounced decrease in sediment size with decreasing sample elevation across all but the coarsest size classes. Measured size distributions become increasingly bimodal with decreasing elevation, exhibiting a coarse, bouldery mode that does not change with elevation and a more abundant finer mode that shifts from cobbles at the highest elevations to gravel at mid elevations and finally to sand at low elevations. We interpret these altitudinal variations in hillslope sediment size to reflect changes in physical, chemical, and biological weathering that can be explained by the catchment's strong altitudinal gradients in topography, climate, and vegetation cover. Because elevation and travel distance to the outlet are closely coupled, the altitudinal trends in sediment size produce a systematic decrease in sediment size along hillslopes parallel to the trunk stream. We refer to this phenomenon as ‘downvalley fining.’ Forward modeling shows that downvalley fining of hillslope sediment is necessary for downstream fining of the long-term average flux of coarse sediment in mountain landscapes where hillslopes and channels are coupled and long-term net sediment deposition is negligible. The model also shows that abrasion plays a secondary role in downstream fining of coarse sediment flux but plays a dominant role in partitioning between the bedload and suspended load. Patterns observed at Inyo Creek may be widespread in mountain ranges around the world. © 2020 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

Temporal variation of chemical and mechanical weathering in NE Iceland: Evaluation of a steady-state model of erosion

This study critically assesses the temporal sensitivity of the steady-state model of erosion that has been applied to chemical and mechanical weathering studies of volcanic islands and the continents, using only one sample from each catchment. The model assumes a geochemical mass balance between the initially unweathered rock of a drainage basin and the dissolved and solid loads of the river.Chemical composition of 178 samples of suspended and dissolved inorganic river constituents, collected in 1998–2002, were studied from five basaltic river catchments in NE Iceland. The Hydrological Service in Iceland has monitored the discharge and the total suspended inorganic matter concentration (SIM) of the glacial rivers for ~ four decades, making it possible to compare modelled and measured SIM fluxes.Concentration of SIM and grain size increased with discharge. As proportion of clay size particles in the SIM samples increased, concentrations of insoluble elements increased and of soluble decreased. The highest proportion of altered basaltic glass was in the clay size particles.The concentration ratio of insoluble elements in the SIM was used along with data on chemical composition of unweathered rocks (high-Mg basalts, tholeiites, rhyolites) to calculate the pristine composition of the original catchment rocks. The calculated rhyolite proportions compare nicely with area-weighted average proportions, from geological maps of these catchments.The calculated composition of the unweathered bedrock was used in the steady-state model, together with the chemical composition of the suspended and dissolved constituents of the river. Seasonal changes in dissolved constituent concentrations resulted in too low modelled concentrations of SIM_mod at high discharge (and too high SIM_mod at low discharge). Samples collected at annual average river dissolved load yielded SIM_mod concentrations close to the measured ones. According to the model, the studied rivers had specific mechanical denudation rates of 1.3–3.0 kg/m²/yr whereas the average measured rates were 0.8–3.5 kg/m²/yr which are among the highest on Earth.This study validates the use of a steady-state model of erosion to estimate mechanical weathering rates at the scale of a river catchment when the collected riverine dissolved load represents the average chemical composition over a mean hydrological year.     

A new method for determining weathering rates in weathering pits

Determining the rates of rock weathering is difficult because, firstly, the weathering rate of rocks is usually so slow that it is difficult to measure; secondly, it is also difficult to determine the start time and duration of weathering. The Shanxi River Valley in Fujian, China dried up after a reservoir was built upstream in 1959, and became a stone quarry site. Quarrying ceased in 1977, so a large amount of quarry wastes with artificially excavated surfaces were left in the valley. The concave-upward curved rocky surface, broken by manual excavation, easily contains rainwater in its central part, which was easily weathered into a more concave surface. Plaster mould casting was performed in situ on such a concave surface of an excavated stone rock in the valley and scanned with a high-precision 3D scanner to obtain 3D data of the concave-upward rock surface and its more concave middle part, which was considered as an initial weathering pit. The 3D model provided an in-depth understanding of the initial formation process of weathering pits, indicating that: (1) the average weathering rate of a weathering pit is 10.8 ± 0.49 cm ka⁻¹; (2) weathering pits are generally formed by standing water in depressions on a flat near-horizontal rock surface due to weathering actions involving water; (3) the deepening rate of a weathering pit is about four times greater than that of the surrounding area; (4) the growth of a weathering pit can begin in some small concavities on the flat rock surface without pre-existing depressions and gradually expands; (5) a weathering pit is generally wider than deep or with a flat bottom due to expansion with a lateral weathering rate that is greater than that of the vertical, and the lamination of the host rock is not necessary for the formation of flat-floored weathering pits. © 2020 John Wiley & Sons, Ltd.