Tide model comparison over the Southwestern Atlantic Shelf

Sea surface height (SSH) as measured by satellites has become a powerful tool for oceanographic and climate related studies. Whereas in the open ocean good accuracy has been achieved, more energetic dynamics and a number of calibration problems have limited applications over continental shelves and near the coast. Tidal ranges in the Southwestern Atlantic (SWA) continental shelf are among the highest in the world ocean, reaching up to 12 m at specific locations. This fact highlights the relevance of the accuracy of the tidal correction that must be applied to the satellite data to be useful in the region. In this work, amplitudes and phases of tidal constituents are extracted from five global tide models and three regional models and compared to the corresponding harmonics estimated from coastal tide gauges (TGs) and satellite altimetry data. The Root Sum Square (RSS) of the misfit of the common set of the five tidal constituents solved by the models (M₂, N₂, S₂, K₁ and O₁) is higher than 18 cm close to the coast for two of the regional models and higher than 24.5 cm for the rest of the models considered. Both values are too high to provide an accurate estimation of geostrophic non-tidal currents from satellite altimetry in the coastal region. On the other hand, the global model with the highest spatial resolution has a RSS lower than 4.5 cm over the continental shelf even when the non-linear M₄ overtide is considered. Comparison with in-situ current measurements suggests that this model can be used to de-tide altimetry data to compute large-scale patterns of SSH and associated geostrophic velocities. It is suggested that a local tide model with very high resolution that assimilates in-situ and satellite data should meet the precision needed to estimate geostrophic velocities at a higher resolution both close to the coast and over the Patagonian shelf.     

Seasonal variation of the <Emphasis Type="Italic">M</Emphasis><Subscript>2</Subscript> tide

The seasonal cycle of the main lunar tidal constituent M ₂ is studied globally by an analysis of a high-resolution ocean circulation and tide model (STORMTIDE) simulation, of 19 years of satellite altimeter data, and of multiyear tide-gauge records. The barotropic seasonal tidal variability is dominant in coastal and polar regions with relative changes of the tidal amplitude of 5–10 %. A comparison with the observations shows that the ocean circulation and tide model captures the seasonal pattern of the M ₂ tide reasonably well. There are two main processes leading to the seasonal variability in the barotropic tide: First, seasonal changes in stratification on the continental shelf affect the vertical profile of eddy viscosity and, in turn, the vertical current profile. Second, the frictional effect between sea-ice and the surface ocean layer leads to seasonally varying tidal transport. We estimate from the model simulation that the M ₂ tidal energy dissipation at the sea surface varies seasonally in the Arctic (ocean regions north of 60°N) between 2 and 34 GW, whereas in the Southern Ocean, it varies between 0.5 and 2 GW. The M ₂ internal tide is mainly affected by stratification, and the induced modified phase speed of the internal waves leads to amplitude differences in the surface tide signal of 0.005–0.0150 m. The seasonal signals of the M ₂ surface tide are large compared to the accuracy demands of satellite altimetry and gravity observations and emphasize the importance to consider seasonal tidal variability in the correction processes of satellite data.     

Computing near coastal tidal dynamics from observations and a numerical model

A two-dimensional vertically integrated model of the North Sea is used to compute the distribution of M₂ and M₄ tidal elevations and currents over the region. Comparison of computed and observed elevations and currents in the area shows that the model can accurately reproduce the M₂ tide in the North Sea, although there are difficulties with the M₄ tide particularly in the northern North Sea.Comparison between model and a large number of observations collected in a shallow water region off the east coast of England, revealed that the model can accurately reproduce the tides even in near coastal regions, where model resolution problems can occur. Comparisons of computed and observed M₂ tidal energy fluxes in this region, show that model and observations agree to within the order of 10% (the error associated with the necessary interpolation of the observations in order to compute the energy flux).The problem of computing energy dissipation in the area by subtracting the energy fluxes into and out of the region is shown to be ill-conditioned in that the energy dissipation in the area is comparable to the error in the energy flux. Consequently for the sea region considered here it is not meaningful to compare this energy budget with energy dissipation due to bottom friction.Energy dissipation for the whole of the North Sea is computed using the numerical model and the geographical distribution of dissipation due to bottom friction is given for the M₂ tide.     

Numerical study of circulation on the inner Amazon Shelf

We studied the circulation on the coastal domain of the Amazon Shelf by applying the hydrodynamic module of the estuarine and coastal ocean model and sediment transport. The first barotropic experiment aimed to explain the major bathymetric effects on tides and those generated by anisotropy in sediment distribution. We analyzed the continental shelf response of barotropic tides under realistic bottom stress parametrization (C _d ), considering sediment granulometry obtained from a faciologic map, where river mud deposits and reworked sediments areas are well distinguished, among others classes of sediments. Very low C _d values were set in the fluid mud regions off the Amapá coast (1.0 10^???4), in contrast to values around 3.5 10^???3 for coarser sediment regions off the Pará coast. Three-dimensional experiments represented the Amazon River discharge and trade winds, combined to barotropic tide influences and induced vertical mixing. The quasiresonant response of the Amazon Shelf to the M₂ tide acts on the local hydrodynamics by increasing tidal admittance, along with tidal forcing at the shelf break and extensive fluid mud regions. Harmonic analysis of modeled currents agreed well with the analysis of the AMASSEDS observational data set. Tidal-induced vertical shear provided strong homogenization of threshold waters, which are subject to a kind of hydraulic control due to the topographic steepness. Ahead of the hydraulic jump, the low-salinity plume is disconnected from the bottom and acquires negative vorticity, turning southeastward. Tides act as a generator mechanism and topography, via hydraulic control, acts as a maintainer mechanism for the low-salinity frontal zone positioning. Tidally induced southeastward plume fate is overwhelmed by northwestward trade winds so that they, along with background circulation, probably play the most important role on the plume fate and variability over the Amazon Shelf.     

A numerical study of the barotropic tides and tidal energy distribution in the Indonesian seas with the assimilated finite volume coastal ocean model

The tides and tidal energetics in the Indonesian seas are simulated using a three-dimensional finite volume coastal ocean model. The high-resolution coastline-fitted model is configured to better resolve the hydrodynamic processes around the numerous barrier islands. A large model domain is adopted to minimize the uncertainty adjacent to open boundaries. The model results with elevation assimilation based on a simple nudge scheme faithfully reproduced the general features of the barotropic tides in the Indonesian Seas. The mean root-mean-square errors between the observed and simulated tidal constants are 2.3, 1.1, 2.4, and 1.5 cm for M₂, S₂, K₁, and O₁, respectively. Analysis of the model solutions indicates that the semidiurnal tides in the Indonesian Seas are primarily dominated by the Indian Ocean, whereas the diurnal tides in this region are mainly influenced by the Pacific Ocean, which is consistent with previous studies. Examinations of tidal energy transport reveal that the tidal energy for both of the simulated tidal constituents are transported from the Indian Ocean into the IS mainly through the Lombok Strait and the Timor Sea, whereas only M₂ energy enters the Banda Sea and continues northward. The tidal energy dissipates the most in the passages on both sides of Timor Island, with the maximum M₂ and K₁ tidal energy transport reaching about 750 and 650 kW m^–1, respectively. The total energy losses of the four dominant constituents in the IS are nearly 338 GW, with the M₂ constituent dissipating 240.8 GW. It is also shown that the bottom dissipation rate for the M₂ tide is about 1–2 order of magnitudes larger than that of the other three tidal components in the Indonesian seas.     

Tidal circulation and energy dissipation in a shallow, sinuous estuary

The tidal dynamics in a pristine, mesotidal (>2 m range), marsh-dominated estuary are examined using moored and moving vessel field observations. Analysis focuses on the structure of the M ₂ tide that accounts for approximately 80% of the observed tidal energy, and indicates a transition in character from a near standing wave on the continental shelf to a more progressive wave within the estuary. A slight maximum in water level (WL) occurs in the estuary 10–20 km from the mouth. M ₂ WL amplitude decreases at 0.015 m/km landward of this point, implying head of tide approximately 75 km from the mouth. In contrast, tidal currents in the main channel 25 km inland are twice those at the estuary mouth. Analysis suggests the tidal character is consistent with a strongly convergent estuarine geometry controlling the tidal response in the estuary. First harmonic (M ₄) current amplitude follows the M ₂ WL distribution, peaking at mid-estuary, whereas M ₄ WL is greatest farther inland. The major axis current amplitude is strongly influenced by local bathymetry and topography. On most bends a momentum core shifts from the inside to outside of the bend moving seaward, similar to that seen in unidirectional river flow but with point bars shifted seaward of the bends. Dissipation rate estimates, based on changes in energy flux, are 0.18–1.65 W m⁻² or 40–175 μW kg^–1. A strong (0.1 m/s), depth-averaged residual flow is produced at the bends, which resembles flow around headlands, forming counter-rotating eddies that meet at the apex of the bends. A large sub-basin in the estuary exhibits remarkably different tidal characteristics and may be resonant at a harmonic of the M ₂ tide.     

Variability of baroclinic tidal currents on the Mackenzie Shelf,the Southeastern Beaufort Sea

Semidiurnal tidal currents on the outer shelf of the Mackenzie Shelf in the Beaufort Sea were found to be strongly influenced by the locally generated baroclinic tide. Two primary factors are involved in this process: (1) the sharp shelf break along the northeastern Mackenzie Shelf, promoting the generation of vigorous internal tidal waves; and (2) the proximity to critical latitudes for M₂ and N₂ motions locking these waves and preventing them from leaving the source region. As a result, internal tides are resonantly trapped between the shelf and critical latitudes. The physical properties and temporal variations of tidal motions were examined using current meter measurements obtained from 1987–1988 at four sites (SS1, SS2, SS3, and SS4) offshore of the shelf break at depths of ∼200 m. Each mooring had Aanderaa RCM4s positioned at ∼35 m below the surface and ∼50 m above the bottom. Complex demodulation was used to compute the envelopes (amplitude modulation) of these components. A striking difference in the variability of clockwise (CW) and counterclockwise (CCW) tidal currents was found. The CW tides are highly variable, have greater amplitude, exhibit a burst-like character associated with wind events and contain about 80% of the total energy of the semidiurnal tidal currents. In contrast, the CCW components have a more regular temporal regime with distinct monthly, fortnightly and 10-day modulation at astronomical periodicities associated with frequency differences M₂–N₂ (0.03629 cpd), S₂–M₂ (0.06773 cpd), and S₂–N₂ (0.10402 cpd). Significant horizontal correlation of the CW current envelopes was found only between stations near the northeast Mackenzie Shelf, indicating this to be the main area of baroclinic internal wave generation.     

Influence of the modified global ocean tide model with local tides of East and South China Seas on load gravity in China and its neighbor area

Introduction With the development of science and technology, the accuracy of gravity measurement is im-proved. The gravity observation with FG5 gravimeter has reached accuracy of μ magnitude. And the high accurate superconducting gravimeter can detect the tiny signal of 10?2 μ magnitude in frequency domain. With the high-accuracy gravity observation on Earth′s surface, the Earth′s tidal parameters can be determined precisely. And the observations can also be used to invert the struc-ture…     

A model study of tidal distributions in the Celtic and Irish Sea regions determined with finite volume and finite element models

An unstructured mesh tidal model of the west coast of Britain, covering the Celtic Sea and Irish Sea is used to compare tidal distributions computed with finite element (FE) and finite volume (FV) models. Both models cover an identical region, use the same mesh, and have topography and tidal boundary forcing from a finite difference model that can reproduce the tides in the region. By this means, solutions from both models can be compared without any bias towards one model or another. Two-dimensional calculations show that for a given friction coefficient, there is more damping in the FV model than the FE model. As bottom friction coefficient is reduced, the two models show comparable changes in tidal distributions. In terms of mesh resolution, calculations show that for the M₂ tide, the mesh is sufficiently fine to yield an accurate solution over the whole domain. However, in terms of higher harmonics of the tide, in particular the M₆ component, its small-scale variability in near-shore regions which is comparable to the mesh of the model, suggests that the mesh resolution is insufficient in the near-coastal regions. Even with a finer mesh in these areas, without detailed bottom topography and a spatial varying friction depending on bed types and bed forms, which is not available, model skill would probably not be improved. In addition in the near-shore region, as shown in the literature, the solution is sensitive to the form of the wetting/drying algorithm used in the model. Calculations with a 3D version of the FV model show that for a given value of k, damping is reduced compared to the 2D version due to the differences in bed stress formulation, with the 3D model yielding an accurate tidal distribution over the region.     

Tidal observations near an amphidrome

The signal to noise ratio in tidal data in the diurnal and semidiurnal frequency bands is ordinarily so large that the noise contribution to the tidal harmonic constants is unimportant. However, as the observational locations are selected progressively closer to an amphidrome (point of no tide), the signal to noise ratio decreases, making the tidal harmonic constants less dependable. Standard deviations in amplitude of M₂ and S₂ obtained from 12 29-day analyses of a year of tide data obtained at a standard tide station, estimated to be 280 and 550 km away from the amphidromes for these constituents in the eastern Caribbean, are roughly one-third of the mean amplitudes for these constituents; the standard deviations in epoch are 38° and 30° respectively. Therefore, a program to locate an amphidrome precisely is self-defeating and the location can only be approximated by a grid of tide observations spanning the geographic position and/or by longer series of observations, using higher resolution to increase the signal to noise ratio. Amplitudes of 0.64 cm and 1.24 cm were calculated for M₂ and S₂ from a one-month series of pelagic observations obtained very close to an inferred position of the M₂ amphidrome in the northeast Caribbean Sea.Abbreviations C&GS Coast and Geodetic Survey - CICAR Cooperative Investigation of the Caribbean and Adjacent Regions - IAPSO International Association for the Physical Sciences of the Ocean - ICOT Institute of Coastal Oceanography and Tides - IDOE International Decade of Ocean Exploration - NOAA National Oceanic and Atmospheric Administration - NOS National Ocean Survey - NSF National Science Foundation - SCOR Scientific Committee of Oceanic Research - UNESCO United Nations Educational, Scientific, and Cultural Organization     

Effect of stratification on tidal circulation over the Scotian Shelf and Gulf of St. Lawrence: a numerical study using a three-dimensional shelf circulation model

A three-dimensional shelf circulation model is used to examine the effect of seasonal changes in water-column stratification on the tidal circulation over the Scotian Shelf and Gulf of St. Lawrence. The model is driven by tidal forcing specified at the model’s lateral open boundaries in terms of tidal sea surface elevations and depth-averaged currents for five major tidal constituents (M₂, N₂, S₂, K₁, and O₁). Three numerical experiments are conducted to determine the influence of baroclinic pressure gradients and changes in vertical mixing, both associated with stratification, on the seasonal variation of tidal circulation over the study region. The model is initialized with climatological hydrographic fields and integrated for 16 months in each experiment. Model results from the last 12 months are analyzed to determine the dominant semidiurnal and diurnal tidal components, M₂ and K₁. Model results suggest that the seasonal variation in the water-column stratification affects the M₂ tidal circulation most strongly over the shelf break and over the deep waters off the Scotian Shelf (through the development of baroclinic pressure gradients) and along Northumberland Strait in the Gulf of St. Lawrence (through changes in vertical mixing and bottom stress). For the K₁ constituent, the baroclinic pressure gradient and vertical mixing have opposing effects on the tidal circulation over several areas of the study region, while near the bottom, vertical mixing appears to play only a small role in the tidal circulation.     

Verifying the body tide at the Canary Islands using tidal gravimetry observations

Gravity tide records from El Hierro, Tenerife and Lanzarote Islands (Canarian Archipelago) have been analyzed and compared to the theoretical body tide model (DDW) of Dehant el al. (1999). The use of more stringent criterion of tidal analysis using VAV program allowed us to reduce the error bars by a factor of two of the gravimetric factors at Tenerife and Lanzarote compared with previous published values. Also, the calibration values have been revisited at those sites. Precise ocean tide loading (OTL) corrections based on up-to-date global ocean models and improved regional ocean model have been obtained for the main tidal harmonics O₁, K₁, M₂, S₂. We also point out the importance of using the most accurate coastline definition for OTL calculations in the Canaries. The remaining observational errors depend on the accuracy of the calibration of the gravimeters and/or on the length of the observed data series. Finally, the comparison of the tidal observations with the theoretical body tide models has been done with an accuracy level of 0.1% at El Hierro, 0.4% at Tenerife and 0.5% at Lanzarote.     

Fine grid tidal modeling of the Yellow and East China Seas

A fine grid tidal modeling experiment is carried out in order to investigate the tidal regimes for major five tidal constituents, the nonlinear tidal phenomena in terms of M₄ and MS₄ generation, and the independent tide by the tide generating force in the Yellow and East China Seas (YECS). In this study a two-dimensional numerical model based upon a subgrid-scale (SGS) stress modeling technique is used with the tide generating force included. The model was validated with recently observed tide and current data. The calculated tidal charts for tidal elevation show a generally good agreement with existing ones, with more accurate feature of the M₂ cotidal chart in comparison with both the observed data and the existing tidal charts. A careful comparison of the computed diurnal amplitude with observations suggests that the diurnal constituents seem to be overdamped especially in the Kyunggi Bay region, for the case when quadratic bottom friction law is used.Propagation features of the M₄(MS₄) tides are discussed in the YECS, based upon the analyses of the observed and calculated results. The amphidromic system of the M₄ is quite complicated and one noticeable characteristic is that the propagation direction of the M₄ tidal wave along the west coast of Korean peninsula is opposite to that of the M₂ tidal wave. This result coincides with observations. The propagation feature of the MS₄ is almost similar to that of the M₄, but with lesser amplitude. The responses of the M₄ tidal features to momentum diffusion term and depth-dependent form of the friction coefficient are also discussed.It is also shown that when the independent tide (Defant, 1960) arising from tide generating force (TGF) coexists with tidal waves (co-oscillating tide) arising from external boundary forcing, the TGF tidal waves are dissipated and their amphidromes tend to move westward. This may be interpreted as a process whereby the incident and reflected TGF tidal waves are damped by co-oscillating tide arising from external force at open boundaries. The TGF amplitude is found to be up to 10 cm and 4 cm in the Kyunggi Bay for the M₂ and S₂ constituents while those for all diurnal constituents are less than 1 cm over the entire model domain.     

On the influence of adequate Weddell Sea characteristics in a large-scale global ocean circulation model

Global ocean circulation models usually lack an adequate consideration of high-latitude processes due to a limited model domain or insufficient resolution. Without the processes in key areas of the global thermohaline circulation, the characteristics and flow of deep and bottom waters cannot be modeled realistically. In this study, a high-resolution (~20 km) ocean model focused on the Weddell Sea sector of the Southern Ocean is combined with a low-resolution (2^° × 2^°) global ocean model applying the state estimation technique. Temperature, salinity, and velocity data on two Weddell Sea sections from the regional model are used as constraints for the large-scale model in addition to satellite altimetry and sea-surface temperatures. The differences between the model with additional constraints and without document that the Weddell Sea circulation exerts significant influence on the course of the Antarctic Circumpolar Current with consequences for Southern Ocean water mass characteristics and the spreading of deep and bottom waters in the South Atlantic. Furthermore, a warming trend in the period 1993–2001 was found in the Weddell Sea and adjacent basins in agreement with float measurements in the upper Southern Ocean. Teleconnections to the North Atlantic are suggested but need further studies to demonstrate their statistical significance.     

Modeling studies of tidal dynamics and the associated responses to coastline changes in the Bohai Sea,China

Over the past 30 years, reclamation projects and related changes have impacted the hydrodynamics and sediment transport in the Bohai Sea. Three-dimensional tidal current models of the Bohai Sea and the Yellow Sea were constructed using the MIKE 3 model. We used a refined grid to simulate and analyze the effects of changes in coastline, depth, topography, reclamation, the Yellow River estuary, and coastal erosion on tidal systems, tide levels, tidal currents, residual currents, and tidal fluxes. The simulation results show that the relative change in the amplitude of the half-day tide is greater than that of the full-day tide. The changes in the tidal amplitudes of M₂, S₂, K₁, and O₁ caused by coastline changes accounted for 27.76–99.07% of the overall change in amplitude from 1987 to 2016, and water depth changes accounted for 0.93–72.24% of the overall change. The dominant factor driving coastline changes is reclamation, accounting for 99.55–99.91% of the amplitude changes in tidal waves, followed by coastal erosion, accounting for 0.05–0.40% of the tidal wave amplitude changes. The contribution of changes in the Yellow River estuary to tidal wave amplitude changes is small, accounting for 0.01–0.12% of the amplitude change factor. The change in the highest tide level (HTL) is mainly related to the amplitude change, and the correlation with the phase change is small. The dominant factor responsible for the change in the HTL is the tide amplitude change in M2, followed by S2, whereas the influence of the K1 and O1 tides on the change in the HTL is small. Reclamation resulted in a decrease in the vertical average maximum flow velocity (V_VAM) in the Bohai Sea. Shallower water depths have led to an increase in the V_VAM; deeper water depths have led to a decrease in the maximum flow velocity. The absolute value of the maximum flow velocity gradually decreases from the surface to the bottom, but the relative change value is basically constant. The changes in the tidal dynamics of the Bohai Sea are proportional to the degree of change in the coastline. The maximum and minimum changes in the tidal flux appear in Laizhou Bay (P-LZB) and Liaodong Bay (P-LDB), respectively. The changes in the tidal flux are related to the change in the area of the bay. Due to the reduced tidal flux, the water exchange capacity of the Bohai Sea has decreased, impacting the ecological environment of the Bohai Sea. Strictly controlling the scale of reclamation are important measures for reducing the decline in the water exchange capacity of the Bohai Sea and the deterioration of its ecological environment.     

An inter-comparison of tidal solutions computed with a range of unstructured grid models of the Irish and Celtic Sea Regions

Three finite element codes, namely TELEMAC, ADCIRC and QUODDY, are used to compute the spatial distributions of the M₂, M₄ and M₆ components of the tide in the sea region off the west coast of Britain. This region is chosen because there is an accurate topographic dataset in the area and detailed open boundary M₂ tidal forcing for driving the model. In addition, accurate solutions (based upon comparisons with extensive observations) using uniform grid finite difference models forced with these open boundary data exist for comparison purposes. By using boundary forcing, bottom topography and bottom drag coefficients identical to those used in an earlier finite difference model, there is no danger of comparing finite element solutions for “untuned unoptimised solutions” with those from a “tuned optimised solution”. In addition, by placing the open boundary in all finite element calculations at the same location as that used in a previous finite difference model and using the same M₂ tidal boundary forcing and water depths, a like with like comparison of solutions derived with the various finite element models was possible. In addition, this open boundary was well removed from the shallow water region, namely the eastern Irish Sea where the higher harmonics were generated. Since these are not included in the open boundary, forcing their generation was determined by physical processes within the models. Consequently, an inter-comparison of these higher harmonics generated by the various finite element codes gives some indication of the degree of variability in the solution particularly in coastal regions from one finite element model to another. Initial calculations using high-resolution near-shore topography in the eastern Irish Sea and including “wetting and drying” showed that M₂ tidal amplitudes and phases in the region computed with TELEMAC were in good agreement with observations. The ADCIRC code gave amplitudes about 30 cm lower and phases about 8° higher. For the M₄ tide, in the eastern Irish Sea amplitudes computed with TELEMAC were about 4 cm higher than ADCIRC on average, with phase differences of order 5°. For the M₆ component, amplitudes and phases showed significant small-scale variability in the eastern Irish Sea, and no clear bias between the models could be found. Although setting a minimum water depth of 5 m in the near-shore region, hence removing wetting and drying, reduced the small-scale variability in the models, the differences in M₂ and M₄ tide between models remained. For M₆, a significant reduction in variability occurred in the eastern Irish Sea when a minimum 5-m water depth was specified. In this case, TELEMAC gave amplitudes that were 1 cm higher and phases 30° lower than ADCIRC on average. For QUODDY in the eastern Irish Sea, average M₂ tidal amplitudes were about 10 cm higher and phase 8° higher than those computed with TELEMAC. For M₄, amplitudes were approximately 2 cm higher with phases of order 15° higher in the northern part of the region and 15° lower in the southern part. For M₆ in the north of the region, amplitudes were 2 cm higher and about 2 cm lower in the south. Very rapid M₆ tidal-phase changes occurred in the near-shore regions. The lessons learned from this model inter-comparison study are summarised in the final section of the paper. In addition, the problems of performing a detailed model–model inter-comparison are discussed, as are the enormous difficulties of conducting a true model skill assessment that would require detailed measurements of tidal boundary forcing, near-shore topography and precise knowledge of bed types and bed forms. Such data are at present not available.     

Earth tides observed by gravity and GPS in southeastern Alaska

We analyzed gravity data obtained in Juneau and global positioning system (GPS) data obtained from three PBO sites in southeastern Alaska (SE-AK), which are part of a US research facility called ‘EarthScope’, and we compared the obtained tidal amplitudes and phases with those estimated from the predicted tides including both effects of the body tide and ocean tide. Global tide models predict the ocean tides in this region of complex coastline and bathymetry. To improve the accuracy of prediction, we developed a regional ocean tide model in SE-AK.Our comparison results suggest: (1) by taking into account the ocean tide effect, the amplitude differences between the observation and the predicted body tide is remarkably reduced for both the gravity and displacement (e.g. for the M₂ constituent, 8.5–0.3 μGal, and 2.4–0.1 cm at the AB50 GPS site in Juneau in terms of the vector sum of three components of the north–south, east–west and up–down), even though the ocean tide loading is large in SE-AK. (2) We have confirmed the precise point positioning (PPP) method, which was used to extract the tidal signals from the original GPS time series, works well to recover the tidal signals. Although the GPS analysis results still contain noise due to the atmosphere and multipath, we may conclude that the GPS observation surely detects the tidal signals with the sub-centimeter accuracy or better for some of the tidal constituents. (3) In order to increase the accuracy of the tidal prediction in SE-AK, it is indispensable to improve the regional ocean tide model developed in this study, especially for the phase.     

Modelling tidally induced sediment-transport paths over the northwest European shelf: the influence of sea-level reduction

A three-dimensional model covering the northwest European Shelf and part of the adjacent Atlantic Ocean is used to examine the influence of water depth change upon the distribution of maximum tidal bed stress. The direction of bed stress is an indicator of sediment movement as bed load and various regions of convergence and divergence in good agreement with observations are identified. Calculations are performed with water depths reduced by 35 m, corresponding to 10 000 years before present (B.P.). Initially, the model is forced by only the M₂ tide, although subsequently five constituents, namely M₂, S₂, N₂, K₁ and O_1, are used for tidal forcing. Although the distribution of extreme bed stresses computed with only M₂ tidal forcing is comparable to that computed with five tides, the additional tidal constituents modify the magnitude of the bed stress. In particular the diurnal tides show regions of local enhanced current amplitude in the shelf-edge region with corresponding changes in bed stress. When water depths are reduced such that the North Sea and English Channel are separated, then there is a significant change in the tidal distribution in the shallow Southern Bight which influences bed-stress distributions and hence bed-load sediment transport in the area. Besides changes in shallow regions, the distribution of tides at the shelf edge is affected. A discussion of the limitations of the present coarse-grid model in shelf-edge regions and how it can be used to provide boundary conditions for limited-area three-dimensional models that can include stratification is presented. Also the importance of stratification for sediment movement at the shelf edge is briefly discussed.Responsible Editor: Phil Dyke     

The 18.6 yr nodal modulation in the tides of Southern European coasts

The nodal modulation of the diurnal (K₁ and O₁) and semi-diurnal (M₂ and K₂) tidal constituents at the coasts of the Mediterranean Sea and the eastern Atlantic is estimated and its spatial variability mapped. Fourteen hourly tide gauge records each spanning more than 18 years are considered in this analysis. Ten tide gauges are located in the Mediterranean Sea and four in the Bay of Biscay. The nodal modulation of the most energetic tidal constituent (M₂) reaches up to 5 cm at the eastern Atlantic coasts, while within the Mediterranean Sea its modulation is in general less than 1.1 cm. The largest K₂ nodal modulation found is 3.7 cm in the eastern Atlantic coasts. In the Mediterranean Sea, smaller modulation amplitudes, ranging between 0.4 and 1.4 cm are found. The K₁ tide constituent has the largest amplitude nodal modulation within the Mediterranean Sea of 1.9 cm in the north Adriatic Sea, which is also larger than the modulation of this constituent at the eastern Atlantic coasts. The O₁ tide constituent has the highest amplitude nodal modulation (1.4 cm) at the eastern Atlantic coasts. In the Mediterranean Sea the maximum value is 1 cm in the north Adriatic Sea.     

Earth tides observed by gravity and GPS in southeastern Alaska

We analyzed gravity data obtained in Juneau and global positioning system (GPS) data obtained from three PBO sites in southeastern Alaska (SE-AK), which are part of a US research facility called ‘EarthScope’, and we compared the obtained tidal amplitudes and phases with those estimated from the predicted tides including both effects of the body tide and ocean tide. Global tide models predict the ocean tides in this region of complex coastline and bathymetry. To improve the accuracy of prediction, we developed a regional ocean tide model in SE-AK.Our comparison results suggest: (1) by taking into account the ocean tide effect, the amplitude differences between the observation and the predicted body tide is remarkably reduced for both the gravity and displacement (e.g. for the M₂ constituent, 8.5–0.3 μGal, and 2.4–0.1 cm at the AB50 GPS site in Juneau in terms of the vector sum of three components of the north–south, east–west and up–down), even though the ocean tide loading is large in SE-AK. (2) We have confirmed the precise point positioning (PPP) method, which was used to extract the tidal signals from the original GPS time series, works well to recover the tidal signals. Although the GPS analysis results still contain noise due to the atmosphere and multipath, we may conclude that the GPS observation surely detects the tidal signals with the sub-centimeter accuracy or better for some of the tidal constituents. (3) In order to increase the accuracy of the tidal prediction in SE-AK, it is indispensable to improve the regional ocean tide model developed in this study, especially for the phase.