斜向波浪作用下双层水平板式防波堤波浪荷载试验研究

In this study, systematic physical model tests were performed to investigate the wave forces on the twin-plate breakwater under irregular waves. Based on the experimental results, the effects of the relative plate width B/L,wave height Hs/D and incident angle θ0 on the wave forces were analyzed and discussed. The results showed that:(1) The envelopes of the total wave pressure were generally symmetrical along the direction of plate width under the incident angles(θ0) being 0°, 15°, 30°, 45° and 60°. In particular, the envelopes of wave pressure atθ0=30° were larger than all other cases.(2) The synchronous pressure distribution of the breakwater under oblique wave action was more complicated comparing to the normal incident waves.(3) Based on data analysis, an empirical formula was obtained to estimate the total vertical force of the twin-plate breakwater.This empirical formula can be a good reference for the design basis of engineering applications under specified wave conditions.     

波浪的物理模型

介绍了常用的实验室造波机原理，讨论了波浪模拟的流体力学问题。     

近岸波浪增水与近岸流的计算方法研究

本文针对实际波浪及地形的复杂性，提出了一套用于计算缓坡不规则地形上波浪增水与近岸流的数学模型。该模型采用经典的力学平衡机制，以二维不规则波浪为源动力，并着考虑了近岸波浪与波浪增水之间的相互作用，其物理背景符合工程应用的要求。     

圆弧面防波堤波浪力初步研究

圆弧面防波堤是在半圆形防波堤基础上开发的一种新型防波堤。首先通过与半圆形防波堤相同条件下的波浪试验,检验圆弧面防波堤的稳定性,并利用数值波浪水槽对圆弧面防波堤的水力特性进行初步研究,探求造成圆弧面防波堤与半圆形防波堤波浪力差别的主要原因。通过圆弧面防波堤与半圆形防波堤波浪力的对比试验,提出了圆弧面防波堤波浪力的简化计算方法,以半圆堤正向水平波浪力乘以一修正系数,在堤顶淹没情况下修正系数可取1.3,在堤顶出水情况下修正系数可取1.1。     

波浪经过网衣的特性研究

依据波浪理论,分析了波浪经过网衣后的流体特性和边界条件,研究了网衣的波浪水动力、波浪透射系数与网衣尺度、特征参数、波浪参数等的关系。设计预加张力放射系泊法进行网衣构件水槽波浪试验。试验构件由10种PE网衣和HDPE框架装配而成,试验工况是规则波,周期为0·8—2·0s,波高为50—250mm。结果表明,作用在网衣上的水平波浪力变化规律与波浪基本一致,呈现周期性和不对称性变化;波浪力变化曲线呈现司托克斯二阶波形状,波峰较陡,波谷较平坦,和波面图相似;网衣水平波浪力周期峰值大约与波高的2·6次方、波长的0·8次方成比例,与网衣宽度l线性相关;随着特征参数d/a增大,网衣波浪力呈线性增加变化,透射系数减少,网衣消浪能力主要集中在网衣水表层。同时设计多层网衣组合的柔性浮式防波堤波浪试验,其消浪能力除了与网衣尺寸、特征参数等相关以外,还与网衣间隔距离有一定的关系。水槽试验时波浪最小透射系数下降到71%左右,从经济、实用角度表明,可用网衣来制作能防护渔业设施的柔性浮式防波堤。     

工程海域波浪特征分析方法比较

通过选取两个典型海外工程项目案例,分别采用波浪特征参数法和波浪谱法对工程海域波浪条件进行分析,并比较这两种方法在作业波浪条件、波浪特征认知程度上的差异,以及对海港水域平面布置产生的影响。对于波浪能量在频域及方向上存在多峰谱情况的海域,基于全谱的波浪特征参数系列数据有可能出现以下两种情况:1)主峰波向掩盖次峰波向;2)主峰波向错配次峰周期。对于上述两种情况,若仅采用波浪特征参数法对工程海域作业波浪条件进行分析,并指导海港水域平面布置,则极可能忽略或误判个别敏感波向、关键频域段的部分波浪能量,从而误导设计,为后续项目运营埋下隐患。对于以上情形,宜采用波浪谱法深入分析工程海域波浪能量在整个频域及各个方向上的详细分布及构成,并对关键波向、关键频域段的波浪能量进行量化,评估其对海港水域平面布置的影响,从而最大程度地避免由于波浪输入条件误判带来的风险。     

波浪在混合式海堤上的爬高

本文通过模型试验以及对影响波浪爬高诸主要因素的递推分析法,分析了波高、波长、平台宽、平台顶高程、斜坡坡比及相对水深等因素对混合式海堤上波浪爬高的影响,并给出了计算波浪爬高的经验公式。     

水流中波浪绕射折射数值计算与分析

提出了水深与流场缓变水域波浪传播数学模型－水流中依赖时间变量并考虑能耗的波浪“缓坡方程”及其等价的控制方程组,分析比较了无不流情况此理论模型与其相庆的两种抛物线型的差别,同时讨论了水流对波浪计算结果的影响。部分计算实例表明：该模型较其他模型能更好地适应河口三角洲大范围水域的波浪传播变形数值计算,且在强流河口呼近岸地区必须考虑水流对波浪影响,否则计算结果将严重失真。     

弧形防波堤波浪力试验研究

在圆筒形防波堤和V形防波堤的基础上,结合离岸堤后形成V形和半圆形连续出现的韵律海岸的地貌平面形态特点,提出一种前墙为连续的半圆筒形防波堤形式。通过在波浪水槽内进行规则波物理模型试验,探究这一新型防波堤的波压力分布规律及波高、周期、水深等因素对波压力的影响。将试验结果与海港水文公式和合田良实公式计算的理论值对比分析,给出了以合田良实公式的折减系数来拟合新型弧形防波堤波浪总水平力的计算公式。结果表明:新型弧形防波堤上的波压力随波高、周期的增大而增大,其水平波浪总力比同等尺度直墙少10%左右。     

波浪变形的数学模型

本文给出一个在复杂水深地形条件下计算包括折射和绕射效应的线性波浪变形数学模型。该模型用差分方法进行求解,并应用于兴化湾江阴岛码头及航道的波浪要素计算,所得结果与其他方法的结果进行比较。通过实际应用说明它是计算开阔海域波浪变形的有力工具。     

潜堤对波浪传播变形的物理模型试验研究

以不可渗透光滑潜堤为研究对象,基于波浪水槽试验,分析了规则波和不规则波通过淹没梯形潜堤时的波浪外部形态变化以及内部能量变化规律。探讨了不同波浪要素(周期、波高、淹没水深)对潜堤附近波高影响的变化规律。同时,探究了潜堤斜坡坡度、堤顶淹没水深对波浪频谱在频域分布的影响。研究结果表明:当波浪通过潜堤时,波浪主频能量衰减,波浪能量由低频向高频移动;潜堤斜坡坡度越大、堤顶水深越小,波浪主频能量衰减越剧烈;波浪通过潜堤后高频波能量占潜堤次生波能量的1%~30%。     

Calculation of Wave Pressure and Pressure Spectrum for Perforate-Pipe Breakwater

Standing waves are formed due to the reflection when waves meet vertical wall,thereforestrong structures are needed to keep the wall stability under the serious wave attack.For the improvementof the working condition and increase of the stability of the wall,the lower reflecting breakwaters have at-tracted close attention Reports mostly from Japanese researchers are often concerned with the wall ofcaisson equipped with open windows.In this paper a kind of hollow-pipe perforated breakwater is exam-ined which waves may partially perforate into the harbour basin.The wave in front of the wall can onlyform partial standing wave and wave force is reduced obviously.And the theoretical calculation of waveforce and analysis of wave force spectrum are all derived.Comparison between the results from theoreticalcalculation and hydraulic modeling shows reasonable agreement.     

挡板透空码头水平波浪力计算方法的探讨

目前,对透空式高桩梁板码头的桩基和墩柱波浪力的计算,现行《海港水文规范》中有相应的公式,但对一侧增设挡浪板及上部结构构件的透空式高桩梁板码头水平波浪力的计算,规范并没有明确规定相应的计算公式。从挡板透空码头设计中水平波浪力的计算分析入手,说明挡板波浪力采用不同计算方法的差异性,并针对某设计工程进行了实例分析,通过相关文献、现行规范及物理模型试验等三种不同方法所得计算结果的比较,探讨一种适合挡板透空码头的水平波浪力的计算方法,供工程设计时参考。     

Experimental Study of Wave Pressure on a Breakwater Pier

Test studies on the wave pressure on a breakwater pier show that the influence of transmissivewave pressure on the outside wall of the breakwater pier is considerable,when the width of the pier is notvery large.The variations of transmissive wave pressure on the breakwater pier with different widths arecompared and the relationship is obtained between relative transmitting distance b/L and wave pressurereduction factor K,which may be used in the design of similar breakwater piers.     

斜向波对直立式防波堤堤头作用的试验研究

直立式防波堤堤头在斜向波浪作用下波浪力的计算在现行的技术规范中尚属空白。通过物理模型试验给出了堤头结构设计所需的波压分布图，指出了波浪入射方向和地形对堤头所受波浪力的贡献有时可以超过波高和波周期，根据现行规范按波浪正向入射计算堤头所受的波浪力偏于安全。     

Calculation of Wave Reflection Coefficient for Perforated-Pipe Breakwater

The hollow-pipe perforated breakwater is of low reflection. In this paper the functions of reflection coefficients of both regular and random waves are theoretically derived, based on the concept of linear superimposition of reflected and incident waves and with the total flow rate continuity of integral form instead of the non-continuity of the boundary condition, and based on the concept of linear wave spectrum theory. Comparisons between theoretical results presented here and measurements of model tests show reasonable agreement.     

日照帆船港港域波高的数值计算

考虑波浪的浅水变化、折射、绕射、反射和破碎等现象的影响,以文氏谱作为输入谱,建立了浅水区域随机波浪传播变形的改进数值模型。对日照帆船港港域波高的数值计算结果表明:在没有越浪的情况下,计算值与物理模型试验观测值吻合。改进的数值模型成为求解港口水域波高的1种有效方法。     

Simplified Method for Calculating Standing Wave Pressure on Vertical Breakwater

Through numerical modeling, a kind of simplified calculating method for standing wave pressure on vertical face breakwater have been put forward. Not only the formulas proposed in this paper are simple in form and very easy in use, but also they possess continuity on the full range of standing wave. And more, the precision requiremennts of calculation can be satisfied to a certain extent in engineering practice.     

波浪与抛石潜堤相互作用的MPS法数值模型研究

为了研究波浪与抛石潜堤相互作用过程中大自由表面变形和堤内渗流等强非线性紊流运动问题,利用改进的MPS法,建立了模拟波浪与抛石潜堤相互作用的MPS法数值计算模型。模型将抛石潜堤假定为均质多孔介质,采用Drew的二相流运动方程描述多孔介质内外的流体运动;通过在动量方程中增加非线性阻力项,并引入亚粒子尺度紊流模型,模拟波浪与可渗结构物相互作用过程中的紊流运动。选取"U"型管中多孔介质内渗流过程和孤立波与可渗潜堤相互作用两个典型的渗流问题,通过将数值计算结果与理论解和实测值的对比分析,对所提出的MPS法紊流渗流模型的模拟精度进行验证。结果表明:基于改进的MPS法构建的垂向二维紊流渗流模型可以很好地再现"U"型管中多孔介质内渗流以及波浪作用下可渗潜堤内外的复杂流场,显著缓解流-固界面处的压力震荡与粒子分布不均匀问题,实现了较高的模拟精度。     

An Improved Coupling of Numerical and Physical Models for Simulating Wave Propagation

An improved coupling of numerical and physical models for simulating 2D wave propagation is developed in this paper. In the proposed model, an unstructured finite element model (FEM) based Boussinesq equations is applied for the numerical wave simulation, and a 2D piston-type wavemaker is used for the physical wave generation. An innovative scheme combining fourth-order Lagrange interpolation and Runge-Kutta scheme is described for solving the coupling equation. A Transfer function modulation method is presented to minimize the errors induced from the hydrodynamic invalidity of the coupling model and/or the mechanical capability of the wavemaker in area where nonlinearities or dispersion predominate. The overall performance and applicability of the coupling model has been experimentally validated by accounting for both regular and irregular waves and varying bathymetry. Experimental results show that the proposed numerical scheme and transfer function modulation method are efficient for the data transfer from the numerical model to the physical model up to a deterministic level.