基于中主应力修正关系的边坡稳定性分析

边坡稳定性分析时通常将应力条件简化为平面应变状态,采用三轴试验强度计算出的边坡稳定性偏于保守。在充分考虑中主应力物理含义及力学机制的基础上,将Mises屈服准则与Mohr-Coulomb（简称M-C）内切圆屈服准则进行匹配,得到了平面应变条件下土体屈服破坏时中主应力的理论修正关系,进而也得到了该条件下最大主应力与最小主应力的比值关系,从理论上证明了该比值关系是与土体平面应变破坏时内摩擦角成一定关系的常数,也在平面应变试验中得到了验证,从侧面反映出中主应力理论修正关系的合理性。由上述两种关系建立了土体平面应变破坏条件下的应力路径,结合Lade-Duncan强度准则,建立了平面应变条件下强度参数与三轴试验试验条件下强度参数转换公式,由该转换公式得到的平面应变条件下的强度参数与平面应变试验实测值误差在2%左右,大幅缩小了三轴试验实测值与平面应变试验实测值的误差。在均质边坡稳定分析中分别采用常规三轴试验强度值与由公式转换得到的平面应变强度值进行计算。研究结果表明,三轴试验条件下内摩擦角为10°～20°之间时,基于两种强度参数得出的安全系数相差不大;当三轴试验条件下内摩擦角大于20°时,平面应变条件下安全系数较三轴试验条件下提高19%左右,但该成果只在文中计算案例有效,两者误差的准确关系还有待于进一步研究。值得关注的是,由于平面应变条件下土体强度变大,边坡的临界滑面深度变浅了,其形态相应变陡。     

应力状态对粗粒料力学特性影响的大型真三轴试验

土石坝所处的应力状态较接近平面应变应力状态或三维应力状态,而常规三轴试验低估了粗粒料的力学性能。应用大型真三轴仪对常规三轴应力状态、平面应变应力状态和真三轴应力状态（ 0.25, 为中主应力系数, 、 、 分别为大、中、小主应力）下粗粒料的力学特性进行了压缩试验研究。试验结果表明：相同小主应力下,常规三轴试验、平面应变试验、真三轴试验的大、小主应力之差与大主应力方向应变的关系曲线依次变高变陡。某一试验加载条件下,体应变随球应力的增大而增大,初始剪切阶段增加较慢,随后呈线性增大,不同小主应力的体应变曲线较为接近。平面应变试验强度和真三轴试验强度比常规三轴试验强度有较大增长,真三轴试验强度增加百分比大于平面应变试验强度增加百分比。初始弹性模量随小主应力的增大呈线性增大。平面应变状态下中主应力系数随大主应力方向应变的增大而增大,初始剪切阶段增长较缓,之后近似呈线性增大。相同小主应力下,从常规三轴应力状态至平面应变应力状态再到真三轴应力状态,小主应力方向应变均为膨胀变形,且膨胀变形依次增大。同一试验加载条件下,小主应力较小时,应力比（偏应力与球应力之比）与偏应变的关系曲线位于上方。     

基于Lade-Duncan准则的平面应变强度公式

在弹性-理想塑性和相关联流动法则的假设下,基于Lade-Duncan准则,得到了平面应变破坏的中主应力条件,提出一种新的平面应变条件下的强度公式。该公式将平面应变条件和常规三轴压缩条件下的抗剪强度指标联系起来,只须通过常规三轴试验,就可确定平面应变条件下的内摩擦角和黏聚力,可以有效反映中主应力对平面应变内摩擦角的提高效应。证明了等效内摩擦角达到极大值的条件即为平面应变条件下无黏性土的破坏条件,以及绘制π平面上3种准则的几何关系,阐明平面应变强度公式的数学意义。最后,通过地基承载力试验结果验证了该公式的有效性。在使用规范方法或有限元软件进行平面应变计算时,该公式可考虑中主应力的影响,选取更为有效的抗剪强度指标。     

粉细砂的真三轴试验与强度特性

采用柔性真三轴仪对上海粉细砂进行了一系列不同中主应力系数条件下的真三轴试验,针对中主应力对粉细砂强度特性的影响进行了系统分析。基于真三轴试验结果对Mohr-Coulomb强度准则的形状函数进行了改进,并采用试验结果对强度准则进行验证。结果表明,建立在真三轴试验基础上的强度准则能更准确地反映砂土三维应力状态下的强度特性。     

考虑中间主应力Hoek-Brown强度准则及其适用性

为考虑中间主应力对岩石极限破坏强度作用,在广义Hoek-Brown强度准则幂率项中添加定量表征中间主应力项,构建新的三维Hoek-Brown强度准则。该准则在主应力空间是通过3个角点外接Hoek-Brown准则包络面的曲六面体,在 空间包络线是幂律型曲线。通过与Hoek-Brown准则、Drucker-Prager准则和Mogi准则分别对4组真三轴压缩强度试验数据的拟合对比分析,探讨其反映中间主应力效应的适用性。结果表明,修正的Hoek-Brown强度准则拟合试验数据效果总体最好,Mogi准则次之,Hoek-Brown准则和Drucker-Prager准则较差。从而修正的Hoek-Brown强度准则最适用于粗面岩、大理岩和花岗岩等硬脆性岩石的真三轴强度预测及中间主应力影响规律描述。     

粉质黏土的真三轴试验及强度特性研究

为研究复杂应力路径下粉质黏土强度特性,利用TSW-40型土壤真三轴仪,开展了不同试验条件下粉质黏土的真三轴试验。研究了真三维应力状态下粉质黏土应力-应变曲线变化规律,探讨了含水率、固结围压和中主应力比等试验条件对粉质黏土强度的影响规律,对比分析了真三维应力状态下 平面上粉质黏土试验值与Mohr-Coulomb（简称M-C）强度准则和双剪强度准则的差异。研究结果表明：真三维应力状态下粉质黏土的广义剪应力-剪应变曲线主要表现为应变硬化型。粉质黏土强度随中主应力比和固结围压的增大而增大,随着含水率的增大而减小。 平面上粉质黏土的强度包络线随静水压力 的增大向外逐渐扩展,随含水率 的增大向内逐渐收缩。 平面上M-C强度极限线和双剪强度屈服极限线与试验值对比分析表明,M-C强度准则描述土体强度时结果偏小,采用双剪强度准则时结果偏大。     

平面应变状态下边坡安全系数的近似求解

Mohr—Coulomb屈服准则不考虑中间主应力对材料强度的贡献,是一个保守的强度屈服准则,在近似平面应变状态下,匹配于Mohr-Coulomb屈服准则的Drucker-Prager屈服准则能给出边坡安全系数偏保守一些的估计;相对而言,Matsuoka—Nakai和Lade-Duncan屈服准则均考虑了中间主应力对土体强度的影响,在近似平面应变状态下,匹配于Matsuoka-Nakai和Lade-Duncan屈服准则的Drucker-Prager屈服准则能给出岩土类材料较为合理的破坏强度预测,土体的抗剪强度能被更有效地发挥出来,因而借助这些转化的Drucker-Prager屈服准则能给出平面应变状态下土坡安全系数较为合理和真实的预测。文中的边坡稳定算例证实了这些观点。     

冻结砂不同应力路径三轴试验强度和变形分析

为研究冻土在复杂应力路径下的力学特性,利用自主研发的冻土三轴仪,进行了广义三轴压缩应力状态、平面应变应力状态和真三轴应力状态下的压缩试验,分析了冻结砂在不同应力状态下的强度演化规律和变形特性。试验结果表明：当小主应力相同时,冻结砂在广义三轴压缩应力状态、平面应变应力状态和真三轴应力状态下的强度和应力-应变曲线的斜率依次增大,小主应力对冻土的强度起到提高作用;小主应力方向始终产生膨胀变形;体应变随着大主应变的增加呈现先剪缩后剪胀的趋势,且在同一试验类型下,小主应力对体应变影响程度较小;同一试验加载条件下,小主应力越小,偏应力与球应力之比的位置越高;从广义三轴压缩应力状态至平面应变应力状态再到真三轴应力状态,试样的破坏强度依次提升。     

非饱和土三剪强度准则及验证

基于材料三剪强度准则和非饱和土力学特性,提出了非饱和土的单应力变量和双应力变量三剪强度准则,并对其做了特征分析。分析表明,通过改变准则中的主应力影响系数b,所提准则就可以对其他强度准则进行非线性近似表达。在π平面的极限线中,所提强度准则覆盖了由内边界的单剪强度准则到外边界的三剪统一强度准则之间的所有外凸区域。因此,其适用于各种复杂应力状态下的非饱和土体,也能反映非饱和土单轴抗拉抗压强度不等的特征。另外,还用其他文献的真三轴试验数据对所提准则做了试验验证,其中,非饱和黏土砂的真三轴试验值与中主应力影响系数b=0.6时的三剪强度准则预测值吻合较好,双应力变量下准则的预测值比单应力变量下的预测值更符合试验值;非饱和黄土真三轴试验值与中主应力影响系数b=0.2时的三剪强度准则预测值吻合较好,两种应力变量下的三剪强度准则预测值差别较小。     

空心圆柱砂岩真三轴试验研究

利用岩石空心圆柱扭剪试验系统针对灰砂岩进行真三轴试验研究,分别开展控制（σ2-σ3）（σ2为中间主应力,σ3为最小主应力）条件压缩试验和恒σ3、变σ2条件压缩试验,对灰砂岩的应力-应变规律、强度特性及破坏特征进行详细分析,并进一步探讨了中间主应力效应,最小主应力效应,应力洛德角效应以及强度准则的适用性。研究结果表明：岩石空心圆柱扭剪试验系统能够实现真三轴应力状态的模拟,相较于常规的实现方式,该方法可避免端部摩擦的影响;内外围压的压差对岩石强度有很大影响,尤其是在高围压下,较大的压差使得岩石强度迅速弱化导致剧烈破坏;中间主应力对岩石强度影响显著且具有区间效应,最小主应力对岩石强度有强化作用,该特点对于实际工程开挖岩体的高效及时支护具有重要的指导意义;进一步地,根据所获试验结果对现阶段用于描述岩石力学特性的强度准则进行分析,认为采用指数强度准则能合理反映岩石真三轴应力状态,具有较好的适用性,可用来评价实际工程中岩石的强度特征。     

Influences of loading direction and intermediate principal stress ratio on the initiation of strain localization in cross-anisotropic sand

Since cross-anisotropic sand behaves differently when the loading direction or the stress state changes, the influences of the loading direction and the intermediate principal stress ratio (b = (σ ₂ ? σ ₃)/(σ ₁ ? σ ₃)) on the initiation of strain localization need study. According to the loading angle (angle between the major principal stress direction and the normal of bedding plane), a 3D non-coaxial non-associated elasto-plasticity hardening model was proposed by modifying Lode angle formulation of the Mohr–Coulomb yield function and the stress–dilatancy function. By using bifurcation analysis, the model was used to predict the initiation of strain localization under plane strain and true triaxial conditions. The predictions of the plane strain tests show that the major principal strain at the bifurcation points increases with the loading angle, while the stress ratio decreases with the loading angle. According to the loading angle and the intermediate principal stress ratio, the true triaxial tests were analyzed in three sectors. The stress–strain behavior and the volumetric strain in each sector can be well captured by the proposed model. Strain localization occurs in most b value conditions in all three sectors except for those which are close to triaxial compression condition (b = 0). The difference between the peak shear strength corresponding to the strain localization and the ultimate shear strength corresponding to plastic limit becomes obvious when the b value is near 0.4. The influence of bifurcation on the shear strength becomes weak when the loading direction changes from perpendicular to the bedding plane to parallel. The bifurcation analysis based on the proposed model gives out major principal strain and peak shear strength at the initiation of strain localization; the given results are consistent with experiments.     

结构性黄土的剪切带及强度特性的真三轴试验研究

采用西安理工大学自主研发的真三轴仪,对西安白鹿原黄土进行了不同中主应力比值、不同固结围压的试验研究,探讨了黄土剪切带形成与峰值强度、中主应变与大主应变关系曲线、体应变与大主应变关系曲线特征点之间的联系以及子午平面、 平面上的强度变化规律。分析了真三轴应力条件下黄土强度变形规律和试样剪切带破坏模式和黄土在复杂应力状态下剪切带形成的判断依据和原因,研究表明,真三轴压缩原状黄土具有明显的剪切带,围压和中主应力比值较小时表现为软化,围压和中主应力比值较大时则表现为硬化;中主应变、体应变与大主应变关系曲线较为一致的转折点反映了土变形性状发生变化;与中主应变方向一致的剪切带两侧土结构块体产生相对滑移,剪切带开始形成和发展;土应变曲线的转折点可以作为土固结结构内剪切带形成的判断依据;子午平面上强度线呈线性变化规律, 平面上呈曲边三角形非线性变化规律,并且与 -SMP强度准则较为接近。不同应力条件下剪切带变化复杂的破坏模式与黄土原生的结构特征和加载共同作用的变化有密切联系。     

Predicting the initiation of static liquefaction of cross‐anisotropic sands under multiaxial stress conditions

Experimental evidence has shown that the liquefaction instability of sands can be affected by its material density, stress state, and inherent anisotropy. In order to predict the initiation of the static liquefaction of inherent cross‐anisotropic sands under multidimensional stress conditions, a rational constitutive model is needed. An elastoplasticity model able to capture the influences of intermediate principal stress ratio (b  = (σ ₂ ? σ ₃)/(σ ₁ ? σ ₃)) and loading direction on stress–strain relationships and volumetric properties was proposed. The yield function was formulated to be controlled by Lode angle, loading direction, and material state; the stress–dilatancy was a material state‐dependent function. After using the existing drained hollow cylinder tests to validate the proposed model, this model was used to simulate the existing undrained hollow cylinder tests. During this simulation, the second‐order work criterion was used to determine the initiation of static liquefaction. The results showed that an increase in both the intermediate principal stress ratio and the loading angle induces a decrease in the second‐order work. Static liquefaction is initiated more easily at a stress state with a large intermediate principal stress ratio and a large loading angle, and the mobilized friction angle at the instability points decreases with the intermediate principal stress ratio and the loading angle. Copyright © 2017 John Wiley & Sons, Ltd.     

基于SMP准则柱孔扩张问题相似解

以柱孔扩张理论为基础,将柱孔扩张后塑性区半径b作为时间刻度,引入扩孔速度概念,将塑性区内任意一点的应力、应变描述成塑性区半径b和柱孔扩张后扩张体单元距孔心距离r的函数,采用平面应变条件下无黏性土的SMP准则和不相关联流动法则,考虑到无黏性土的剪胀性,推导出柱孔扩张后极限扩张力 的相似解。通过参数分析表明,土体强度和剪胀性对塑性区半径和极限扩张力产生很大的影响,即随着土体强度和剪胀性的增加,极限扩张力明显增加,相应塑性区半径却随之减小。通过与基于摩尔-库仑准则解答进行对比分析表明,考虑中间主应力影响的SMP准则所得到的极限扩张力明显高于基于摩尔-库仑准则的解答。该解答为无黏性土中进行静力触探（CPT）试验和静压桩等岩土工程问题提供必要的理论依据。     

平面应变条件下M-C材料屈服时的中主应力公式

基于Mohr-Coulomb准则,通过引入罗德角参数及Mohr-Coulomb准则平面应变等效广义Mises准则,推导了平面应变条件下材料屈服时的中主应力公式,并给出其与基于SMP准则（Spatial Mobiliaztion Piane）的平面应变中主应力公式之间的关系式。对平面应变条件下的条形地基进行了有限元数值模拟,计算结果验证了所推导的平面应变条件下M-C材料屈服时的中主应力公式的正确性,其公式为岩土体的强度和变形分析、中主应力的强度效应的进一步研究,以及Mohr-Coulomb准则的修正提供了有力的基础。     

Strength criterion for cross-anisotropic sand under general stress conditions

By incorporating the fabric effect and Lode’s angle dependence into the Mohr–Coulomb failure criterion, a strength criterion for cross-anisotropic sand under general stress conditions was proposed. The obtained criterion has only three material parameters which can be specified by conventional triaxial tests. The formula to calculate the friction angle under any loading direction and intermediate principal stress ratio condition was deduced, and the influence of the degree of the cross-anisotropy was quantified. The friction angles of sand in triaxial, true triaxial, and hollow cylinder torsional shear tests were obtained, and a parametric analysis was used to detect the varying characteristics. The friction angle becomes smaller when the major principal stress changes from perpendicular to parallel to the bedding plane. The loading direction and intermediate principal stress ratio are unrelated in true triaxial tests, and their influences on the friction angle can be well captured by the proposed criterion. In hollow cylinder torsional shear tests with the same internal and external pressures, the loading direction and intermediate principal stress ratio are related. This property results in a lower friction angle in the hollow cylinder torsional shear test than that in the true triaxial test under the same intermediate principal stress ratio condition. By comparing the calculated friction angle with the experimental results under various loading conditions (e.g., triaxial, true triaxial, and hollow cylinder torsional shear test), the proposed criterion was verified to be able to characterize the shear strength of cross-anisotropic sand under general stress conditions.     

Non‐coaxial elasto‐plasticity model and bifurcation prediction of shear banding in sands

Numerous constitutive models built on coaxial theory and validated under axi‐symmetric condition often describe the stress–stain relationships and predict the inceptions of shear banding in sands inaccurately under true triaxial condition. By adopting an elaborated Mohr–Coulomb yield function and using non‐coaxial non‐associated flow rule, a 3D non‐coaxial elasto‐plasticity model is proposed and validated by a series of true triaxial tests on loose sands. The bifurcation analysis of true triaxial tests on dense sands predicts the influence of the intermediate principal stress ratio on the onset of shear band accurately. The failure of soils is shown to be related to the formation of shear band under most intermediate principal stress ratio conditions except for those which are close to the axi‐symmetric compression condition. Copyright © 2009 John Wiley & Sons, Ltd.     

软岩洞室最优支护的广义SMP准则解与对比研究

现有洞室最优支护设计均基于Mohr-Coulomb（简称M-C）准则,不能真实反映岩石强度的中间主应力效应以及围岩的三向不等应力状态。基于广义SMP准则和稳定蠕变J3准则,考虑中间主应力对岩石强度的提高作用,建立了软岩洞室最优支护力与围岩允许最大位移的理论解答。洞室最优支护解答对M-C准则、外接圆Drucker-Prager（简称D-P）准则均具有很好的拓展性,且工程实例验证了其正确性。研究结果表明：3种强度准则结果间的差异实际反映的是对中间主应力效应的不同考虑,M-C准则和外接圆D-P准则对应的结果是两个极端情况,推荐选用广义SMP准则解答;岩石长期强度是洞室最优支护设计的关键参数,围岩凝聚力与内摩擦角的影响亦很显著,应合理测定岩石的强度参数并充分考虑变异性。