Time and temperature dependency of carbon dioxide triggered metal(loid) mobilization in soil

Assessing the influence of CO₂ on soil and aquifer geochemistry is a task of increasing interest when considering risk assessment for geologic carbon sequestration. Leakage and CO₂ ascent can lead to soil acidification and mobilization of potentially toxic metals and metalloids due to desorption or dissolution reactions. We studied the CO₂ influence on an Fe(III) (oxyhydr)oxide rich, gleyic Fluvisol sampled in close vicinity to a Czech mofette site and compared the short-term CO₂ influence in laboratory experiments with observations on long-term influence at the natural site. Six week batch experiments with/without CO₂ gas flow at 3 different temperatures and monitoring of liquid phase metal(loid) concentrations revealed two main short-term mobilization processes. Within 1 h to 1 d after CO₂ addition, mobilization of weakly adsorbed metal cations occurred due to surface protonation, most pronounced for Mn (2.5–3.3 fold concentration increase, mobilization rates up to 278 ± 18 μg Mn kg_soil⁻¹ d⁻¹) and strongest at low temperatures. However, total metal(loid) mobilization by abiotic desorption was low. After 1–3 d significant Fe mobilization due to microbially-triggered Fe(III) (oxyhydr)oxide dissolution began and continued throughout the experiment (up to 111 ± 24 fold increase or up to 1.9 ± 0.6 mg Fe kg_soil⁻¹ d⁻¹). Rates increased at higher temperature and with a higher content of organic matter. The Fe(III) mineral dissolution was coupled to co-release of incorporated metal(loid)s, shown for As (up to 16 ± 7 fold, 11 ± 8 μg As kg_soil⁻¹ d⁻¹). At high organic matter content, re-immobilization due to resorption reactions could be observed for Cu. The already low pH (4.5–5.0) did not change significantly during Fe(III) reduction due to buffering from sorption and dissolution reactions, but a drop in redox potential (from > +500 mV to minimum +340 ± 20 mV) occurred due to oxygen depletion. We conclude that microbial processes following CO₂ induction into a soil can contribute significantly to metal(loid) mobilization, especially at optimal microbial growth conditions (moderate temperature, high organic carbon content) and should be considered for carbon sequestration monitoring and risk assessment.     

Wellbore cement fracture evolution at the cement–basalt caprock interface during geologic carbon sequestration

Composite Portland cement–basalt caprock cores with fractures, as well as neat Portland cement columns, were prepared to understand the geochemical and geomechanical effects on the integrity of wellbores with defects during geologic carbon sequestration. The samples were reacted with CO₂–saturated groundwater at 50 °C and 10 MPa for 3 months under static conditions, while one cement–basalt core was subjected to mechanical stress at 2.7 MPa before the CO₂ reaction. Micro-XRD and SEM–EDS data collected along the cement–basalt interface after 3-month reaction with CO₂–saturated groundwater indicate that carbonation of cement matrix was extensive with the precipitation of calcite, aragonite, and vaterite, whereas the alteration of basalt caprock was minor. X-ray microtomography (XMT) provided three-dimensional (3-D) visualization of the opening and interconnection of cement fractures due to mechanical stress. Computational fluid dynamics (CFD) modeling further revealed that this stress led to the increase in fluid flow and hence permeability. After the CO₂-reaction, XMT images displayed that calcium carbonate precipitation occurred extensively within the fractures in the cement matrix, but only partially along the fracture located at the cement–basalt interface. The 3-D visualization and CFD modeling also showed that the precipitation of calcium carbonate within the cement fractures after the CO₂-reaction resulted in the disconnection of cement fractures and permeability decrease. The permeability calculated based on CFD modeling was in agreement with the experimentally determined permeability. This study demonstrates that XMT imaging coupled with CFD modeling represent a powerful tool to visualize and quantify fracture evolution and permeability change in geologic materials and to predict their behavior during geologic carbon sequestration or hydraulic fracturing for shale gas production and enhanced geothermal systems.     

Effects of freshwater Synechococcus sp. cyanobacteria pH buffering on CaCO3 precipitation: Implications for CO2 sequestration

In the present study, a mixed-flow steady-state bio-reactor was designed to biomineralize CO₂ as a consequence of photosynthesis from active Synechococcus sp. Dissolved CO₂, generated by constant air bubbling of inorganic and cyanobacteria stock solutions, was the only source of inorganic carbon. The release of hydroxide ion by cyanobacteria from photosynthesis maintained highly alkaline pH conditions. In the presence of Ca²⁺ and carbonate species, this led to calcite supersaturation under steady state conditions. Ca²⁺ remained constant throughout the experiments showing the presence of steady state conditions. Similarly, the Synechococcus sp. biomass concentration remained stable within uncertainty. A gradual pH decrease was observed for the highest Ca²⁺ condition coinciding with the formation of CaCO₃. The high degree of supersaturation, under steady-state conditions, contributed to the stabilization of calcite and maintained a constant driving force for the mineral nucleation and growth. For the highest Ca²⁺ condition a fast crystal growth rate was consistent with rapid calcite precipitation as suggested further by affinity calculations. Although saturation state based kinetic precipitation models cannot accurately reflect the controls on crystal growth kinetics or reliably predict growth mechanisms, the relatively reaction orders obtained from modeling of calcite precipitation rates as function of decreasing carbonate concentration suggest that the precipitation occurred via surface-controlled rate determining reactions. These high reaction orders support in addition the hypothesis that crystal growth proceeded through complex surface controlled mechanisms. In conclusion, the steady state supersaturated conditions generated by a constant cyanobacteria biomass and metabolic activity strongly suggest that these microorganisms could be used for the development of efficient CO₂ sequestration methods in a controlled large-scale environment.     

Use of mineral/solution equilibrium calculations to assess the potential for carnotite precipitation from groundwater in the Texas Panhandle,USA

This study investigated the potential for the uranium mineral carnotite (K₂(UO₂)₂(VO₄)₂·3H₂O) to precipitate from evaporating groundwater in the Texas Panhandle region of the United States. The evolution of groundwater chemistry during evaporation was modeled with the USGS geochemical code PHREEQC using water-quality data from 100 groundwater wells downloaded from the USGS National Water Information System (NWIS) database. While most modeled groundwater compositions precipitated calcite upon evaporation, not all groundwater became saturated with respect to carnotite with the system open to CO₂. Thus, the formation of calcite is not a necessary condition for carnotite to form. Rather, the determining factor in achieving carnotite saturation was the evolution of groundwater chemistry during evaporation following calcite precipitation. Modeling in this study showed that if the initial major-ion groundwater composition was dominated by calcium-magnesium-sulfate (>70 precent Ca + Mg and >50 percent SO₄ + Cl) or calcium-magnesium-bicarbonate (>70 percent Ca + Mg and <70 percent HCO₃ + CO₃) and following the precipitation of calcite, the concentration of calcium was greater than the carbonate alkalinity (2mCa⁺² > mHCO₃⁻ + 2mCO₃⁻²) carnotite saturation was achieved. If, however, the initial major-ion groundwater composition is sodium-bicarbonate (varying amounts of Na, 40–100 percent Na), calcium-sodium-sulfate, or calcium-magnesium-bicarbonate composition (>70 percent HCO₃ + CO₃) and following the precipitation of calcite, the concentration of calcium was less than the carbonate alkalinity (2mCa⁺² < mHCO₃^- + 2mCO₃⁻²) carnotite saturation was not achieved. In systems open to CO_2, carnotite saturation occurred in most samples in evaporation amounts ranging from 95 percent to 99 percent with the partial pressure of CO₂ ranging from 10^−3.5 to 10^−2.5 atm. Carnotite saturation occurred in a few samples in evaporation amounts ranging from 98 percent to 99 percent with the partial pressure of CO₂ equal to 10^−2.0 atm. Carnotite saturation did not occur in any groundwater with the system closed to CO₂.     

Carbonation of lignite fly ash at ambient T and P in a semi-dry reaction system for CO2 sequestration

The global rise in atmospheric greenhouse gas concentrations calls for practicable solutions to capture CO₂. In this study, a mineral carbonation process was applied in which CO₂ reacts with alkaline lignite ash and forms stable carbonate solids. In comparison to previous studies, the assays were conducted at low temperatures and pressures and under semi-dry reaction conditions in an 8 L laboratory mixing device. In order to find optimum process conditions the pCO₂ (10-20%), stirring rate (500-3000 rpm) and the liquid to solid ratio (L/S = 0.03-0.36 L kg⁻¹) were varied. In all experiments a considerable CO₂ uptake from the gas phase was observed. Concurrently the solid phase contents of Ca and Mg (hydr)oxides decreased and CaCO₃ and MgCO₃ fractions increased throughout the experiments, showing that CO₂ was stabilized as a solid carbonate. The carbonation reaction depends on three factors: Dissolution of CO₂ in the liquid phase, mobilization of Ca and Mg from the mineral surface and precipitation of the carbonate solids. Those limitations were found to depend strongly on the variation of the process parameters. Optimum reaction conditions could be found for L/S ratios between 0.12 and 0.18, medium stirring velocities and pCO₂ between 10% and 20%.Maximum CO₂ uptake by the solid phase was 4.8 mmol g⁻¹ after 120 min, corresponding to a carbonation efficiency for the alkaline material of 53% of the theoretical CO₂ binding capacity. In comparison to previous studies both CO₂ uptake and carbonation efficiencies were in a similar range, but the reaction times in the semi-dry process were considerably shorter. The proposed method additionally allows for a more simple carbonation setup due to low T and P, and produces an easier to handle product with low water content.     

Carbonation of alkaline paper mill waste to reduce CO2 greenhouse gas emissions into the atmosphere

The global warming of Earth’s near-surface, air and oceans in recent decades is a direct consequence of anthropogenic emission of greenhouse gases into the atmosphere such as CO₂, CH₄, N₂O and CFCs. The CO₂ emissions contribute approximately 60% to this climate change. This study investigates experimentally the aqueous carbonation mechanisms of an alkaline paper mill waste containing about 55 wt% portlandite (Ca(OH)₂) as a possible mineralogical CO₂ sequestration process. The overall carbonation reaction includes the following steps: (1) Ca release from portlandite dissolution, (2) CO₂ dissolution in water and (3) CaCO₃ precipitation. This CO₂ sequestration mechanism was supported by geochemical modelling of final solutions using PHREEQC software, and observations by scanning electron microscope and X-ray diffraction of final reaction products. According to the experimental protocol, the system proposed would favour the total capture of approx. 218 kg of CO₂ into stable calcite/ton of paper waste, independently of initial CO₂ pressure. The final product from the carbonation process is a calcite (ca. 100 wt%)-water dispersion. Indeed, the total captured CO₂ mineralized as calcite could be stored in degraded soils or even used for diverse industrial applications. This result demonstrates the possibility of using the alkaline liquid–solid waste for CO₂ mitigation and reduction of greenhouse effect gases into the atmosphere.     

Modeling of coal bed methane (CBM) production and CO2 sequestration in coal seams

A mathematical model was developed to predict the coal bed methane (CBM) production and carbon dioxide (CO₂) sequestration in a coal seam accounting for the coal seam properties. The model predictions showed that, for a CBM production and dewatering process, the pressure could be reduced from 15.17 MPa to 1.56 MPa and the gas saturation increased up to 50% in 30 years for a 5.4 × 10⁵ m² of coal formation. For the CO₂ sequestration process, the model prediction showed that the CO₂ injection rate was first reduced and then slightly recovered over 3 to 13 years of injection, which was also evidenced by the actual in seam data. The model predictions indicated that the sweeping of the water in front of the CO₂ flood in the cleat porosity could be important on the loss of injectivity. Further model predictions suggested that the injection rate of CO₂ could be about 11 × 10³ m³ per day; the injected CO₂ would reach the production well, which was separated from the injection well by 826 m, in about 30 years. During this period, about 160 × 10⁶ m³ of CO₂ could be stored within a 21.4 × 10⁵ m² of coal seam with a thickness of 3 m.     

Contribution of a sewage sludge application to the short-term carbon sequestration across a wide range of agricultural soils

The atmospheric levels of carbon dioxide (CO₂) and other greenhouse gases (GHGs) have increased dramatically since the industrial revolution. The atmospheric enrichment with CO₂ and other GHGs has resulted in multiple negative consequences: such as the increase in the average temperature and the rise of the sea level. Hence, there is a growing interest in developing feasible methods to reduce the atmospheric levels of these gases. One of these strategies is to enhance C sequestration through the increase of soil organic carbon (SOC) pool by the amendment of agricultural soils with sewage sludge. However, there is considerable uncertainty about the effects (positive or negative) of sewage sludge applications on the SOC pool. Thus, a simple approach developed under laboratory conditions is presented to discern the effect of a single sewage sludge application of 50 t ha⁻¹ on the short-term SOC pool in 60 contrasting agricultural soils. The role of soil factors in the C sequestration of the recently added carbon was also studied. The application of sewage sludge supposed a mean increase of 1.7 ± 1.6 g SOC kg⁻¹, with peak increases of up to 3.8 g SOC kg⁻¹ and decreases of up to 4.6 g SOC kg⁻¹. The initial SOC contents conditioned the C sequestration after sewage sludge application, and no other soil property was related.     

Economic analysis of carbon dioxide sequestration in powder river basin coal

Unminable coalbeds are potentially large storage reservoirs for the sequestration of anthropogenic CO₂ and offer the benefit of enhanced methane production, which can offset some of the costs associated with CO₂ sequestration. The objective of this paper is to study the economic feasibility of CO₂ sequestration in unminable coal seams in the Powder River Basin of Wyoming. Economic analyses of CO₂ injection options are compared. Results show that injecting flue gas to recover methane from CBM fields is marginally economical; however, this method will not significantly contribute to the need to sequester large quantities of CO₂. Separating CO₂ from flue gas and injecting it into the unminable coal zones of the Powder River Basin seam is currently uneconomical, but can effectively sequester over 86,000 tons (78,200 Mg) of CO₂ per acre while recovering methane to offset costs. The cost to separate CO₂ from flue gas was identified as the major cost driver associated with CO₂ sequestration in unminable coal seams. Improvements in separations technology alone are unlikely to drive costs low enough for CO₂ sequestration in unminable coal seams in the Powder River Basin to become economically viable. Breakthroughs in separations technology could aid the economics, but in the Powder River Basin they cannot achieve the necessary cost reductions for breakeven economics without incentives.     

The hydromagnesite playas of Atlin, British Columbia, Canada: A biogeochemical model for CO2 sequestration

Anthropogenic greenhouse gas emissions may be offset by sequestering carbon dioxide (CO₂) through the carbonation of magnesium silicate minerals to form magnesium carbonate minerals. The hydromagnesite [Mg₅(CO₃)₄(OH)₂·4H₂O] playas of Atlin, British Columbia, Canada provide a natural model to examine mineral carbonation on a watershed scale. At near surface conditions, CO₂ is biogeochemically sequestered by microorganisms that are involved in weathering of bedrock and precipitation of carbonate minerals. The purpose of this study was to characterize the weathering regime in a groundwater recharge zone and the depositional environments in the playas in the context of a biogeochemical model for CO₂ sequestration with emphasis on microbial processes that accelerate mineral carbonation.Regions with ultramafic bedrock, such as Atlin, represent the best potential sources of feedstocks for mineral carbonation. Elemental compositions of a soil profile show significant depletion of MgO and enrichment of SiO₂ in comparison to underlying ultramafic parent material. Polished serpentinite cubes were placed in the organic horizon of a coniferous forest soil in a groundwater recharge zone for three years. Upon retrieval, the cube surfaces, as seen using scanning electron microscopy, had been colonized by bacteria that were associated with surface pitting. Degradation of organic matter in the soil produced chelating agents and acids that contributed to the chemical weathering of the serpentinite and would be expected to have a similar effect on the magnesium-rich bedrock at Atlin. Stable carbon isotopes of groundwater from a well, situated near a wetland in the southeastern playa, indicate that  12% of the dissolved inorganic carbon has a modern origin from soil CO₂.The mineralogy and isotope geochemistry of the hydromagnesite playas suggest that there are three distinct depositional environments: (1) the wetland, characterized by biologically-aided precipitation of carbonate minerals from waters concentrated by evaporation, (2) isolated wetland sections that lead to the formation of consolidated aragonite sediments, and (3) the emerged grassland environment where evaporation produces mounds of hydromagnesite. Examination of sediments within the southeastern playa–wetland suggests that cyanobacteria, sulphate reducing bacteria, and diatoms aid in producing favourable geochemical conditions for precipitation of carbonate minerals.The Atlin site, as a biogeochemical model, has implications for creating carbon sinks that utilize passive microbial, geochemical and physical processes that aid in mineral carbonation of magnesium silicates. These processes could be exploited for the purposes of CO₂ sequestration by creating conditions similar to those of the Atlin site in environments, artificial or natural, where the precipitation of magnesium carbonates would be suitable. Given the vast quantities of Mg-rich bedrock that exist throughout the world, this study has significant implications for reducing atmospheric CO₂ concentrations and combating global climate change.     

Contribution of a Dense Population of the Brittle Star <Emphasis Type="Italic">Acrocnida brachiata</Emphasis> (Montagu) to the Biogeochemical Fluxes of CO<Subscript>2</Subscript> in a Temperate Coastal Ecosystem

The production of organic matter and calcium carbonate by a dense population of the brittle star Acrocnida brachiata (Echinodermata) was calculated using demographic structure, population density, and relations between the size (disk diameter) and the ash-free dry weight (AFDW) or the calcimass. During a 2-year survey in the Bay of Seine (Eastern English Channel, France), organic production varied from 29 to 50 g_AFDW m⁻² year⁻¹ and CaCO₃ production from 69 to 104 g_CaCO3 m⁻² year⁻¹. Respiration was estimated between 1.7 and 2.0 mol_CO2 m⁻² year⁻¹. Using the molar ratio (ψ) of CO₂ released: CaCO₃ precipitated, this biogenic precipitation of calcium carbonate would result in an additional release between 0.5 and 0.7 mol_CO2 m⁻² year⁻¹ that represented 23% and 26% of total CO₂ fluxes (sum of calcification and respiration). The results of the present study suggest that calcification in temperate shallow environments should be considered as a significant source of CO₂ to seawater and thus a potential source of CO₂ to the atmosphere, emphasizing the important role of the biomineralization (estimated here) and dissolution (endoskeletons of dead individuals) in the carbon budget of temperate coastal ecosystems.     

Experimental identification of CO2–water–rock interactions caused by sequestration of CO2 in Westphalian and Buntsandstein sandstones of the Campine Basin (NE-Belgium)

Geological sequestration of CO₂ is one of the options studied to reduce greenhouse gas emissions. Although the feasibility of this concept is proven, apart from literature data on modelling still little is known about the CO₂–water–rock interactions induced by CO₂-injection.To evaluate the effect of CO₂–water–rock interactions on three sandstone aquifers in NE-Belgium an experimental setup was built. Eighteen experiments were performed in which sandstones were exposed to supercritical CO₂. CO₂–water–rock interactions were deduced from the evolution of aqueous concentrations of 25 species and a thorough characterisation of the sandstones before and after treatment. The results show that dissolution of ankerite/dolomite and Al-silicates could enhance porosity/permeability. The observed precipitation of end-member carbonates could increase storage capacity if it exceeds carbonate dissolution. Precipitation of the latter and of K-rich clays as observed, however, can hamper the injection.     

The CO2 system in rivers of the Australian Victorian Alps: CO2 evasion in relation to system metabolism and rock weathering on multi-annual time scales

The patterns of dissolved inorganic C (DIC) and aqueous CO₂ in rivers and estuaries sampled during summer and winter in the Australian Victorian Alps were examined. Together with historical (1978–1990) geochemical data, this study provides, for the first time, a multi-annual coverage of the linkage between CO₂ release via wetland evasion and CO₂ consumption via combined carbonate and aluminosilicate weathering. δ¹³C values imply that carbonate weathering contributes ∼36% of the DIC in the rivers although carbonates comprise less than 5% of the study area. Baseflow/interflow flushing of respired C3 plant detritus accounts for ∼50% and atmospheric precipitation accounts for ∼14% of the DIC. The influence of in river respiration and photosynthesis on the DIC concentrations is negligible. River waters are supersaturated with CO₂ and evade ∼27.7 × 10⁶ mol/km²/a to ∼70.9 × 10⁶ mol/km²/a CO₂ to the atmosphere with the highest values in the low runoff rivers. This is slightly higher than the global average reflecting higher gas transfer velocities due to high wind speeds. Evaded CO₂ is not balanced by CO₂ consumption via combined carbonate and aluminosilicate weathering which implies that chemical weathering does not significantly neutralize respiration derived H₂CO₃. The results of this study have implications for global assessments of chemical weathering yields in river systems draining passive margin terrains as high respiration derived DIC concentrations are not directly connected to high carbonate and aluminosilicate weathering rates.     

Charging time of tight gas in the Upper Paleozoic of the Ordos Basin,central China

The Upper Paleozoic section contains a tight gas sandstone reservoir (of 2.75 × 10¹² m³) in the Ordos Basin, central China. The measured porosities (< 10%) and permeabilities (generally < 1 mD) are the result of significant mechanical and chemical compaction and precipitation of carbonate, quartz and authigenic clay cements. Fluid inclusion geochemistry and kinetic modeling (generation of gaseous components and δ¹³C₁) were integrated to constrain the timing of gas charge into the tight reservoir. The modeling results indicate that the natural gases in the present reservoir are similar to gases liberated from quartz inclusions in both composition and stable carbon isotope values and also similar to gas generated from Upper Paleozoic coal. The similar geochemistry suggests that an important phase of quartz cementation must have occurred after gas emplacement in the reservoirs during regional uplift at the end of the Cretaceous. The latest carbonate cement, postdating quartz cementation, consumed most of the late CO₂ generated from coal at high maturity (R_O > 1.7%) and reduced the reservoir quality dramatically. On the contrary, tight sandstones from non-producing areas have fluid inclusions that were trapped in quartz cements much earlier. These data indicate that natural gas migrated into the Upper Paleozoic reservoir when it still retained high porosity and permeability. The reservoir continued to experience porosity and permeability reduction from continued quartz and carbonate cementation after gas charging due to low gas saturation. Comparison of the relative timing of gas charging with that of sandstone cementation can help to predict areas of risk during tight gas exploration and development.     

Chemical effects of sulfur dioxide co-injection with carbon dioxide on the reservoir and caprock mineralogy and permeability in depleted gas fields

The most suitable candidates for subsurface storage of CO₂ are depleted gas fields. Their ability to retain CO₂ can however be influenced by the effect which impurities in the CO₂ stream (e.g. H₂S and SO₂) have on the mineralogy of reservoir and seal. In order to investigate the effects of SO₂ we carried out laboratory experiments on reservoir and cap rock core samples from gas fields in the northeast of the Netherlands. The rock samples were contained in reactor vessels for 30 days in contact with CO₂ and 100 ppm SO₂ under in-situ conditions (300 bar, 100 °C). The vessels also contained brine with the same composition as in the actual reservoir. Furthermore equilibrium modeling was carried out using PHREEQC software in order to model the experiments on caprock samples.After the experiments the permeability of the reservoir samples had increased by a factor of 1.2–2.2 as a result of dissolution of primary reservoir minerals. Analysis of the associated brine samples before and after the experiments showed that concentrations of K, Si and Al had increased, indicative of silicate mineral dissolution.In the caprock samples, composed of carbonate and anhydrite minerals, permeability changed by a factor of 0.79–23. The increase in permeability is proportional to the amount of carbonate in the caprock. With higher carbonate content in comparison with anhydrite the permeability increase is higher due to the additional carbonate dissolution. This dependency of permeability variations was verified by the modeling study. Hence, caprock with a higher anhydrite content in comparison with carbonate minerals has a lower risk of leakage after co-injection of 100 ppmv SO₂ with CO₂.     

Diel Aquatic CO<Subscript>2</Subscript> System Dynamics of a Bermudian Mangrove Environment

Mangrove ecosystems play an important, but understudied, role in the cycling of carbon in tropical and subtropical coastal ocean environments. In the present study, we examined the diel dynamics of seawater carbon dioxide (CO₂) and dissolved oxygen (DO) for a mangrove-dominated marine ecosystem (Mangrove Bay) and an adjacent intracoastal waterway (Ferry Reach) on the island of Bermuda. Spatial and temporal trends in seawater carbonate chemistry and associated variables were assessed from direct measurements of dissolved inorganic carbon, total alkalinity, dissolved oxygen (DO), temperature, and salinity. Diel pCO₂ variability was interpolated across hourly wind speed measurements to determine variability in daily CO₂ fluxes for the month of October 2007 in Bermuda. From these observations, we estimated rates of net sea to air CO₂ exchange for these two coastal ecosystems at 59.8 ± 17.3 in Mangrove Bay and 5.5 ± 1.3 mmol m⁻² d⁻¹ in Ferry Reach. These results highlight the potential for large differences in carbonate system functioning and sea-air CO₂ flux in adjacent coastal environments. In addition, observation of large diel variability in CO₂ system parameters (e.g., mean pCO₂: 390–2,841 μatm; mean pH_T: 8.05–7.34) underscores the need for careful consideration of diel cycles in long-term sampling regimes and flux estimates.     

Carbonate and carbon isotopic evolution of groundwater contaminated by produced water brine with hydrocarbons

The major ionic and dissolved inorganic carbon (DIC) concentrations and the stable carbon isotope composition of DIC (δ¹³C_DIC) were measured in a freshwater aquifer contaminated by produced water brine with petroleum hydrocarbons. Our aim was to determine the effects of produced water brine contamination on the carbonate evolution of groundwater. The groundwater was characterized by three distinct anion facies: HCO₃⁻-rich, SO₄²⁻-rich and Cl⁻-rich. The HCO₃⁻-rich groundwater is undergoing closed system carbonate evolution from soil CO_2(g) and weathering of aquifer carbonates. The SO₄²⁻-rich groundwater evolves from gypsum induced dedolomitization and pyrite oxidation. The Cl⁻-rich groundwater is contaminated by produced water brine and undergoes common ion induced carbonate precipitation. The δ¹³C_DIC of the HCO₃⁻-rich groundwater was controlled by nearly equal contribution of carbon from soil CO_2(g) and the aquifer carbonates, such that the δ¹³C of carbon added to the groundwater was −11.6‰. In the SO₄²⁻-rich groundwater, gypsum induced dedolomitization increased the ¹³C such that the δ¹³C of carbon added to the groundwater was −9.4‰. In the produced water brine contaminated Cl⁻-rich groundwater, common ion induced precipitation of calcite depleted the ¹³C such that the δ¹³C of carbon added to the groundwater was −12.7‰. The results of this study demonstrate that produced water brine contamination of fresh groundwater in carbonate aquifers alters the carbonate and carbon isotopic evolution.     

Carbonate precipitation in artificial soils as a sink for atmospheric carbon dioxide

Turnover of C in soils is the dominant flux in the global C cycle and is responsible for transporting 20 times the quantity of anthropogenic emissions each year. This paper investigates the potential for soils to be modified with Ca-rich materials (e.g. demolition waste or basic slag) to capture some of the transferred C as geologically stable CaCO₃. To test this principal, artificial soil known to contain Ca-rich minerals (Ca silicates and portlandite) was analysed from two sites across NE England, UK. The results demonstrate an average C content of 30 ± 15.3 Kg C m⁻² stored as CaCO₃, which is three times the expected organic C content and that it has accumulated at a rate of 25 ± 12.8 t C ha⁻¹ a⁻¹ since 1996. Isotopic analysis of the carbonates gave values between −6.4‰ and −27.5‰ for δ¹³C and −3.92‰ and −20.89‰ for δ¹⁸O, respectively (against V-PDB), which suggests that a combination of carbonate formation mechanisms are operating including the hydroxylation of gaseous CO₂ in solution, and the sequestration of degraded organic C with minor remobilisation/precipitation of lithogenic carbonates. This study implies that construction/development sites may be designed with a C capture function to sequester atmospheric C into the soil matrix with a maximum global potential of 290 Mt C a⁻¹.     

Climatic and lithologic controls on the temporal and spatial variability of CO2 consumption via chemical weathering: An example from the Australian Victorian Alps

A detailed geochemical study on river waters of the Australian Victorian Alps was carried out to determine: (i) the relative significance of silicate, carbonate, evaporite and sulfide weathering in controlling the major ion composition and; (ii) the factors regulating seasonal and spatial variations of CO₂ consumption via silicate weathering in the catchments. Major ion chemistry implies that solutes are largely derived from evaporation of precipitation and chemical weathering of carbonate and silicate lithologies. The input of solutes from rock weathering was determined by calculating the contribution of halite dissolution and atmospheric inputs using local rain and snow samples. Despite the lack of carbonate outcrops in the study area and waters being undersaturated with respect to calcite, the dissolution of vein calcite accounts for up to 67% of the total dissolved cations, generating up to 90% of dissolved Ca and 97% of Mg. Dissolved sulfate has δ³⁴S values of 16 to 20‰_CDT, indicating that it is derived predominantly from atmospheric deposition and minor gypsum weathering and not from bacterial reduction of FeS₂. This militates against sulphuric acid weathering in Victorian rivers. Ratios of Si vs. the atmospheric corrected Na and K concentrations range from ~ 1.1 to ~ 4.3, suggesting incongruent weathering from plagioclase to smectite, kaolinite and gibbsite.Estimated long-term average CO₂ fluxes from silicate weathering range from ~ 0.012 × 10⁶ to 0.039 × 10⁶ mol/km²/yr with the highest values in rivers draining the basement outcrops rather than sedimentary rocks. This is about one order of magnitude below the global average which is due to low relief, and the arid climate in that region. Time series measurements show that exposure to lithology, high physical erosion and long water–rock contact times dominate CO₂ consumption fluxes via silicate weathering, while variations in water temperature are not overriding parameters controlling chemical weathering. Because the atmospheric corrected concentrations of Na, K and Mg act non-conservative in Victorian rivers the parameterizations of weathering processes, and net CO₂ consumption rates in particular, based on major ion abundances, should be treated with skepticism.