Oxidation of As(III) by MnO2 in the absence and presence of Fe(II) under acidic conditions

Oxidation of As(III) by natural manganese (hydr)oxides is an important geochemical reaction mediating the transformation of highly concentrated As(III) in the acidic environment such as acid mine drainage (AMD) and industrial As-contaminated wastewater, however, little is known regarding the presence of dissolved Fe(II) on the oxidation process. In this study, oxidation of As(III) in the absence and presence of Fe(II) by MnO₂ under acidic conditions was investigated. Kinetic results showed that the presence of Fe(II) significantly inhibited the removal of As(III) (including oxidation and sorption) by MnO₂ in As(III)-Fe(II) simultaneous oxidation system even at the molar ratio of Fe(II):As(III) = 1/64:1, and the inhibitory effects increased with the increasing ratios of Fe(II):As(III). Such an inhibition could be attributed to the formation of Fe(III) compounds covering the surface of MnO₂ and thus preventing the oxidizing sites available to As(III). On the other hand, the produced Fe(III) compounds adsorbed more As(III) and the oxidized As(V) on the MnO₂ surface with an increasing ratio of Fe(II):As(III) as demonstrated in kinetic and XPS results. TEM and EDX results confirmed the formation of Fe compounds around MnO₂ particles or separated in solution in Fe(II) individual oxidation system, Fe(II) pre-treated and simultaneous oxidation processes, and schwertmannite was detected in Fe(II) individual and Fe pre-treated oxidation processes, while a new kind of mineral, probably amorphous FeOHAs or FeAsO₄ particles were detected in Fe(II)-As(III) simultaneous oxidation process. This suggests that the mechanisms are different in Fe pre-treated and simultaneous oxidation processes. In the Fe pre-treated and MnO₂-mediated oxidation pathway, As(III) diffused through a schwertmannite coating formed around MnO₂ particles to be oxidized. The newly formed As(V) was adsorbed onto the schwertmannite coating until its sorption capacity was exceeded. Arsenic(V) then diffused out of the coating and was released into the bulk solution. The diffusion into the schwertmannite coating and the oxidation of As(III) and sorption of both As(V) and As(III) onto the coating contributed to the removal of total As from the solution phase. In the simultaneous oxidation pathway, the competitive oxidation of Fe(II) and As(III) on MnO₂ occurred first, followed by the formation of FeOHAs or FeAsO₄ around MnO₂ particles, and these poorly crystalline particles of FeOHAs and FeAsO₄ remained suspended in the bulk solution to adsorb As(III) and As(V). The present study reveals that the formation of Fe(III) compounds on mineral surfaces play an important role in the sorption and oxidation of As(III) by MnO₂ under acidic conditions in natural environments, and the mechanisms involved in the oxidation of As(III) depend upon how Fe(II) is introduced into the As(III)-MnO₂ system.     

Permanganate oxidation of arsenic(III): Reaction stoichiometry and the characterization of solid product

Permanganate (MnO₄⁻) has widely been used as an effective oxidant for drinking water treatment systems, as well as for in situ treatment of groundwater impacted by various organic contaminants. The reaction stoichiometry of As(III) oxidation by permanganate has been assumed to be 1.5, based on the formation of solid product, which is putatively considered to be MnO₂(s). This study determined the stoichiometric ratio (SR) of the oxidation reaction with varying doses of As(III) (3-300 μM) and MnO₄⁻ (0.5 or 300 μM) under circumneutral pH conditions (pH 4.5-7.5). We also characterized the solid product that was recovered ∼1 min after the oxidation of 2.16 mM As(III) by 0.97 mM MnO₄⁻ at pH 6.9 and examined the feasibility of secondary heterogeneous As(III) oxidation by the solid product. When permanganate was in excess of As(III), the SR of As(III) to Mn(VII) was 2.07 ± 0.07, regardless of the solution pH; however, it increased to 2.49 ± 0.09 when As(III) was in excess. The solid product was analogous to vernadite, a poorly crystalline manganese oxide based on XRD analysis. The average valence of structural Mn in the solid product corresponded to +III according to the splitting interval of the Mn3s peaks (5.5 eV), determined using X-ray photoelectron spectroscopy (XPS). The relative proportions of the structural Mn(IV):Mn(III):Mn(II) were quantified as 19:62:19 by fitting the Mn2p_3/2 spectrum of the solid with the five multiplet binding energy spectra for each Mn valence. Additionally, the O1s spectrum of the solid was comparable to that of Mn-oxide but not of Mn-hydroxide. These results suggest that the solid product resembled a poorly crystalline hydrous Mn-oxide such as (Mn^II_0.19Mn^III_0.62Mn^IV_0.19)₂O₃·nH₂O, in which Mn(II) and Mn(IV) were presumably produced from the disproportionation of aqueous phase Mn(III). Thermodynamic calculations also show that the formation of Mn(III) oxide is more favorable than that of Mn(IV) oxide from As(III) oxidation by permanganate under circumneutral pH conditions. Arsenic(III), when it remained in the solution after all of the permanganate was consumed, was effectively oxidized by the solid product. This secondary heterogeneous As(III) oxidation consisted of three steps: sorption to and oxidation on the solid surface and desorption of As(V) into solution, with the first step being the rate-limiting process as observed in As(III) oxidation by various Mn (oxyhydr)oxides reported elsewhere. We also discussed a potential reaction pathway of the permanganate oxidation of As(III).     

The oxidation of cobalt(II) adsorbed on manganese dioxide

X-ray photoelectron spectroscopy (XPS) measurements of cobalt adsorbed on MnO₂ reveal strong evidence that Co(II) has been oxidized to Co(III). The manganese spectra are characteristic of Mn(IV). Model calculations suggest that Co(II) cannot be oxidized by O₂ to Co(III) in bulk solution at seawater concentrations but that the oxidation can proceed in the presence of the strong electric field at the MnO₂-solution interface. Ni(II), however, cannot be oxidized at the interface except at very high concentrations. These calculations suggest that the oxidation of Co(II) can explain the geochemical separation of cobalt from nickel.     

Rapid photo-oxidation of Mn(II) mediated by humic substances

The oxidation of Mn(II) by O₂ to Mn(III) or Mn(IV) is thermodynamically favored under the pH and pO₂ conditions present in most near surface waters, but the kinetics of this reaction are extremely slow. This work investigated whether reactive oxygen species, produced through illumination of humic substances, could oxidize Mn at an environmentally relavent rate. The simulated sunlight illumination of a solution containing 200 μM Mn(II) and 5 mg/L Aldrich humic acid buffered at pH 8.1 produced ∼19 μM of oxidized Mn (MnO_x where x is between one and two) after 45 minutes. The major oxidants reponsible for this reaction appear to be photoproduced superoxide radical anion, O₂⁻, and singlet molecular oxygen, ¹O₂. The dependencies of MnO_x formation on Mn(II), humic acid, and H⁺ concentration were characterized. A kinetic model based largely on published rate constants was established and fit to the experimental data. As expected, analysis of the model indicates that the key reaction rate controlling MnO_x production is the rate of decomposition of a MnO₂⁺ complex formed from the reaction of Mn(II) with O₂⁻. This rate is strongly dependent on the Mn(II) complexing ligands in solution. The MnO_x production in the seawater sample taken from Bodega Bay, USA and spiked with 200 μM Mn(II) was well reproduced by the model. Extrapolations from the model imply that Mn photo-oxidation should be a significant reaction in typical surface seawaters. Calculated rates, 5.8 to 55 pM h⁻¹, are comparable to reported rates of biological Mn oxidation, 0.07 to 89 pM h⁻¹. Four fresh water samples that were spiked with 200 μM Mn(II) also showed significant MnO_x production. Based on these results, it appears that Mn photo-oxidation could constitute a significant, and apparently unrecognized geochemical pathway in natural waters.     

Inter-relationships of MnO2 precipitation, siderophore-Mn complex formation, siderophore degradation, and iron limitation in Mn-oxidizing bacterial cultures

To examine the pathways that form Mn^(III) and Mn^(IV) in the Mn^(II)-oxidizing bacterial strains Pseudomonas putida GB-1 and MnB1, and to test whether the siderophore pyoverdine (PVD) inhibits Mn^(IV)O₂ formation, cultures were subjected to various protocols at known concentrations of iron and PVD. Depending on growth conditions, P. putida produced one of two oxidized Mn species - either soluble PVD-Mn^(III) complex or insoluble Mn^(IV)O₂ minerals - but not both simultaneously. PVD-Mn^(III) was present, and MnO₂ precipitation was inhibited, both in iron-limited cultures that had synthesized 26-50 μM PVD and in iron-replete (non-PVD-producing) cultures that were supplemented with 10-550 μM purified PVD. PVD-Mn^(III) arose by predominantly ligand-mediated air oxidation of Mn^(II) in the presence of PVD, based on the following evidence: (a) yields and rates of this reaction were similar in sterile media and in cultures, and (b) GB-1 mutants deficient in enzymatic Mn oxidation produced PVD-Mn^(III) as efficiently as wild type. Only wild type, however, could degrade PVD-Mn^(III), a process linked to the production of both MnO₂ and an altered PVD with absorbance and fluorescence spectra markedly different from those of either PVD or PVD-Mn^(III). Two conditions, the presence of bioavailable iron and the absence of PVD at concentrations exceeding those of Mn, both had to be satisfied for MnO₂ to appear. These results suggest that P. putida cultures produce soluble Mn^(III) or MnO₂ by different and mutually inhibitory pathways: enzymatic catalysis yielding MnO₂ under iron sufficiency or PVD-promoted oxidation yielding PVD-Mn^(III) under iron limitation. Since PVD-producing Pseudomonas species are environmentally prevalent Mn oxidizers, these data predict influences of iron (via PVD-Mn^(III) versus MnO₂) on the global oxidation/reduction cycling of various pollutants, recalcitrant organic matter, and elements such as C, S, N, Cr, U, and Mn.     

Aerobic oxidation of mackinawite (FeS) and its environmental implication for arsenic mobilization

Oxidation of mackinawite (FeS) and concurrent mobilization of arsenic were investigated as a function of pH under oxidizing conditions. At acidic pH, FeS oxidation is mainly initiated by the proton-promoted dissolution, which results in the release of Fe(II) and sulfide in the solution. While most of dissolved sulfide is volatilized before being oxidized, dissolved Fe(II) is oxidized into green rust-like precipitates and goethite (α-FeOOH). At basic pH, the development of Fe(III) (oxyhydr)oxide coating on the FeS surface inhibits the solution-phase oxidation following FeS dissolution. Instead, FeS is mostly oxidized into lepidocrocite (γ-FeOOH) via the surface-mediated oxidation without dissolution. At neutral pH, FeS is oxidized via both the solution-phase oxidation following FeS dissolution and the surface-mediated oxidation mechanisms. The mobilization of arsenic during FeS oxidation is strongly affected by FeS oxidation mechanisms. At acidic pH (and to some extent at neutral pH), the rapid FeS dissolution and the slow precipitation of Fe (oxyhydr)oxides results in arsenic accumulation in water. In contrast, the surface-mediated oxidation of FeS at basic pH leads to the direct formation of Fe (oxyhydr)oxides, which provides effective adsorbents for As under oxic conditions. At acidic and neutral pH, the solution-phase oxidation of dissolved Fe(II) accelerates the oxidation of the less adsorbing As(III) to the more adsorbing As(V). This study reveals that the oxidative mobilization of As may be a significant pathway for arsenic enrichment of porewaters in sulfidic sediments.     

Oxidative removal of Mn(II) from solution catalysed by the γ-FeOOH (lepidocrocite) surface

A laboratory study was undertaken to ascertain the role of surface catalysis in Mn(II) oxidative removal. γ-FeOOH, a ferric oxyhydroxide formed by O₂ oxidation of ferrous iron in solution, was studied in the following ways: surface charge characteristics by acid base titration, adsorption of Mn(II) and surface oxidation of Mn(II). A rate law was formulated to account for the effects of pH and the amount of surface on the surface oxidation rate of Mn(II). The presence of milli-molar levels of γ-FeOOH was shown to reduce significantly the half-life of Mn(II) in 0.7 M NaCl from hundreds of hours to hours. The numerical values of the surface rate constants for the γ-FeOOH and that reported for colloidal MnO₂ are comparable in order of magnitude.     

Heterogeneous Fe(II) oxidation and zeta potential

The determination of electrophoretic mobility and zeta potential was used as a diagnostic tool, alongside kinetic experiments, to delineate between three plausible mechanisms for the heterogeneous oxidation of Fe(II) by dissolved oxygen. One of these mechanisms is dependant on the positive surface charge that exists on Fe(III) (oxy)hydroxide surfaces at pH values below the Iso-Electric Point (IEP). However, this mechanism can be disputed as catalysis is observed on Fe(III) (oxy)hydroxide surfaces above the IEP despite a negative zeta potential. As well as an IEP shift an overall reduction of the magnitude of the zeta potential is observed in samples of field Fe(III) (oxy)hydroxide collected from the Taff Merthyr mine water treatment site in South Wales, UK. Low zeta potentials determined in mine water treatment systems will have beneficial effects for particle coagulation and settling in passive mine water treatment systems.     

Defining manganese(II) removal processes in passive coal mine drainage treatment systems through laboratory incubation experiments

Oxic limestone beds are commonly used for the passive removal of Mn(II) from coal mine drainage (CMD). Aqueous Mn(II) is removed via oxidative precipitation of Mn(III/IV) oxides catalyzed by Mn(II)-oxidizing microbes and Mn oxide (MnO_x) surfaces. The relative importance of these two processes for Mn removal was examined in laboratory experiments conducted with sediments and CMD collected from eight Mn(II)-removal beds in Pennsylvania and Tennessee, USA. Sterile and non-sterile sediments were incubated in the presence/absence of air and presence/absence of fungicides to operationally define the relative contributions of Mn removal processes. Relatively fast rates of Mn removal were measured in four of the eight sediments where 63–99% of Mn removal was due to biological oxidation. In contrast, in the four sediments with slow rates of Mn(II) removal, 25–63% was due to biological oxidation. Laboratory rates of Mn(II) removal were correlated (R² = 0.62) to bacterial biomass concentration (measured by phospholipid fatty acids (PLFA)). Furthermore, laboratory rates of Mn(II) removal were correlated (R² = 0.87) to field-scale performance of the Mn(II)-removal beds. A practical recommendation from this study is to include MnO_x-coated limestone (and associated biomass) from an operating bed as “seed” material when constructing new Mn(II)-removal beds.     

Preservation of water samples for arsenic(III/V) determinations: an evaluation of the literature and new analytical results

Published literature on preservation procedures for stabilizing aqueous inorganic As(III/V) redox species contains discrepancies. This study critically evaluates published reports on As redox preservation and explains discrepancies in the literature. Synthetic laboratory preservation experiments and time stability experiments were conducted for natural water samples from several field sites. Any field collection procedure that filters out microorganisms, adds a reagent that prevents dissolved Fe and Mn oxidation and precipitation, and isolates the sample from solar radiation will preserve the As(III/V) ratio. Reagents that prevent Fe and Mn oxidation and precipitation include HCl, H₂SO₄, and EDTA, although extremely high concentrations of EDTA are necessary for some water samples high in Fe. Photo-catalyzed Fe(III) reduction causes As(III) oxidation; however, storing the sample in the dark prevents photochemical reactions. Furthermore, the presence of Fe(II) or SO₄ inhibits the oxidation of As(III) by Fe(III) because of complexation reactions and competing reactions with free radicals. Consequently, fast abiotic As(III) oxidation reactions observed in the laboratory are not observed in natural water samples for one or more of the following reasons: (1) the As redox species have already stabilized, (2) most natural waters contain very low dissolved Fe(III) concentrations, (3) the As(III) oxidation caused by Fe(III) photoreduction is inhibited by Fe(II) or SO₄.     

Distribution of arsenic and its mobility in shallow aquifer sediments from Ambikanagar, West Bengal, India

Sediments from a core retrieved during installation of a shallow drinking water well in Ambikanagar (West Bengal, India) were analyzed for various physical and chemical parameters. The geochemical analyses included: (1) a 4-step sequential extraction scheme to determine the distribution of As between different fractions, (2) As speciation (As³⁺ vs. As⁵⁺), and (3) C, N and S isotopes. The sediments have a low percentage of organic C and N (0.10-0.56% and 0.01-0.05%, respectively). Arsenic concentration is between 2 and 7 mg kg⁻¹, and it is mainly associated with the residual fraction, less susceptible to chemical weathering. The proportion of As³⁺ in these sediments is high and ranges from 24% to 74%. Arsenic in the second fraction (reducible) correlates well with Mn, and in the residual fraction As correlates well with several transition elements. The stable isotope results indicate microbial oxidation of organic matter involving SO₄ reduction. Oxidation of primary sulfide minerals and release of As from reduction of Fe-(oxy)hydroxides do not seem important mechanisms in As mobilization. Instead, the dominance of As³⁺ and presence of As⁵⁺ reducing microorganisms in this shallow aquifer imply As remobilization involving microbial processes that needs further investigations.     

Oxidation of aqueous Cr(III) at birnessite surfaces: constraints on reaction mechanism

X-ray Photoelectron Spectroscopy (XPS) was used to investigate oxidation of aqueous Cr(III) at the surface of 7 Å-birnessite [MnO_1.75(OH)_0.25]. Special emphasis was placed on detection of intermediate oxidation states of chromium due to their critical environmental significance. No previous studies have been able to identify these intermediate oxidation states of chromium (namely, Cr[IV] and Cr[V]) on mineral surfaces or in natural solutions. Mn(2p_3/2), Cr(2p_3/2) and O(1s) spectra of the reacted surfaces reveal that Mn(IV) of synthetic birnessite undergoes reductive dissolution in two steps. The first step involves Mn(IV) reduction to Mn(III),that forms at the oxide surface probably as an oxyhydroxide (MnOOH), and in the second step Mn(III) is reduced to Mn(II) that is subsequently taken into solution. Each reductive reaction step involves transfer of only one electron to the Mn ion. After Cr(III)_aq is adsorbed onto the MnO₂ surface, it undergoes oxidation in three separate steps, each involving the loss of one electron to Mn ions, so that Cr(IV), Cr(V) and Cr(VI) are produced. The intermediate reaction products, namely Mn(III), and Cr(V) were positively identified by XPS spectral analyses. Similarity in XPS binding energy values of Cr(III) and Cr(IV) as well as that of Cr(V) and Cr(VI), however, preclude separate identification of Cr(III) from Cr(IV) and Cr(VI) from Cr(V) multiplets on the near-surface of the solid. A parallel reaction scheme (exclusive of sorption reactions) best describes the birnessite-Cr(III)_aq redox reactions. The two parallel reactions proceed by separate mechanisms with a monodentate complex formed in one mechanism and a bidentate complex in another. The bulk of Cr(IV) probably is formed via the monodentate complex and Cr(V) via the bidentate complex. The rate expressions associated with these reactions display near-perfect correlation with changing surface abundances of Cr(IV) and Cr(V) as a function of reaction time. Copyright © 1999 Elsevier Science Ltd.     

氧化锰矿物的生物成因及其性质的研究进展

土壤中的氧化锰矿物是原生矿物风化和成土过程的产物,是最具反应活性的一类矿物,决定着环境中许多物质的形态、迁移和转化,在元素生物地球化学循环中起着重要的作用,其形成机制和环境效应备受关注。已有的研究表明,环境中氧化锰的形成与微生物作用紧密相关,微生物作用可使自然环境中的Mn(Ⅱ)氧化速率提高105倍。参与Mn(Ⅱ)氧化的微生物在环境中广泛存在,已知的典型锰氧化细菌分布在变形菌门、放线菌门或厚壁菌门,它们均通过胞外聚合物中的多铜氧化酶来催化氧化Mn(Ⅱ)。细菌氧化Mn(II)成Mn(Ⅳ)是酶催化的两个连续的快速单电子传递过程,Mn(Ⅲ)在溶液中以与酶结合的瞬时中间态出现。生物形成氧化锰的最初形态为层状锰矿物,与δ-MnO2或酸性水钠锰矿很类似,且结晶弱,粒径小,锰氧化度高,结构中的八面体空穴多,因而比化学形成的氧化锰具有更强的吸附、氧化等表面活性。环境中Mn(Ⅱ)微生物氧化及形成的Mn(Ⅲ)中间体与碳、氮、硫等生命元素的地球化学循环的关系令人关注。     

Adsorption and surface oxidation of Fe(II) on metal (hydr)oxides

The Fe(II) adsorption by non-ferric and ferric (hydr)oxides has been analyzed with surface complexation modeling. The CD model has been used to derive the interfacial distribution of charge. The fitted CD coefficients have been linked to the mechanism of adsorption. The Fe(II) adsorption is discussed for TiO₂, γ-AlOOH (boehmite), γ-FeOOH (lepidocrocite), α-FeOOH (goethite) and HFO (ferrihydrite) in relation to the surface structure and surface sites. One type of surface complex is formed at TiO₂ and γ-AlOOH, i.e. a surface-coordinated Fe²⁺ ion. At the TiO₂ (Degussa) surface, the Fe²⁺ ion is probably bound as a quattro-dentate surface complex. The CD value of Fe²⁺ adsorbed to γ-AlOOH points to the formation of a tridentate complex, which might be a double edge surface complex. The adsorption of Fe(II) to ferric (hydr)oxides differs. The charge distribution points to the transfer of electron charge from the adsorbed Fe(II) to the solid and the subsequent hydrolysis of the ligands that coordinate to the adsorbed ion, formerly present as Fe(II). Analysis shows that the hydrolysis corresponds to the hydrolysis of adsorbed Al(III) for γ-FeOOH and α-FeOOH. In both cases, an adsorbed M(III) is found in agreement with structural considerations. For lepidocrocite, the experimental data point to a process with a complete surface oxidation while for goethite and also HFO, data can be explained assuming a combination of Fe(II) adsorption with and without electron transfer. Surface oxidation (electron transfer), leading to adsorbed Fe(III)(OH)₂, is favored at high pH (pH > ∼7.5) promoting the deprotonation of two Fe_III-OH₂ ligands. For goethite, the interaction of Fe(II) with As(III) and vice versa has been modeled too. To explain Fe(II)-As(III) dual-sorbate systems, formation of a ternary type of surface complex is included, which is supposed to be a monodentate As(III) surface complex that interacts with an Fe(II) ion, resulting in a binuclear bidentate As(III) surface complex.     

Geochemical and mineralogical aspects of sulfide mine tailings

Tailings generated during processing of sulfide ores represent a substantial risk to water resources. The oxidation of sulfide minerals within tailings deposits can generate low-quality water containing elevated concentrations of SO₄, Fe, and associated metal(loid)s. Acid generated during the oxidation of pyrite [FeS₂], pyrrhotite [Fe_(1−x)S] and other sulfide minerals is neutralized to varying degrees by the dissolution of carbonate, (oxy)hydroxide, and silicate minerals. The extent of acid neutralization and, therefore, pore-water pH is a principal control on the mobility of sulfide-oxidation products within tailings deposits. Metals including Fe(III), Cu, Zn, and Ni often occur at high concentrations and exhibit greater mobility at low pH characteristic of acid mine drainage (AMD). In contrast, (hydr)oxyanion-forming elements including As, Sb, Se, and Mo commonly exhibit greater mobility at circumneutral pH associated with neutral mine drainage (NMD). These differences in mobility largely result from the pH-dependence of mineral precipitation–dissolution and sorption–desorption reactions. Cemented layers of secondary (oxy)hydroxide and (hydroxy)sulfate minerals, referred to as hardpans, may promote attenuation of sulfide-mineral oxidation products within and below the oxidation zone. Hardpans may also limit oxygen ingress and pore-water migration within sulfide tailings deposits. Reduction–oxidation (redox) processes are another important control on metal(loid) mobility within sulfide tailings deposits. Reductive dissolution or transformation of secondary (oxy)hydroxide phases can enhance Fe, Mn, and As mobility within sulfide tailings. Production of H₂S via microbial sulfate reduction may promote attenuation of sulfide-oxidation products, including Fe, Zn, Ni, and Tl, via metal-sulfide precipitation. Understanding the dynamics of these interrelated geochemical and mineralogical processes is critical for anticipating and managing water quality associated with sulfide mine tailings.     

The mechanisms of Co(II) oxidation on synthetic birnessite

Studies of the adsorption of Co(II) on synthetic birnessite have been carried out at pH 4, 6, 7, 8 and 10. At pH values of 4, 6 and 7 cobalt(II) is oxidized to Co(III) while at pH 8 and 10 surface cobalt corresponds to Co(II). The Co(II) produced at pH 8 and 10 appears to be Co(OH)₂ produced via precipitation on the MnO₂ surface. The oxidizing agent is identified as surface Mn(IV) from a comparison of x-ray photoelectron spectroscopic results for samples prepared at pH 6.5 under anaerobic and aerobic conditions. The identification of Mn(III) is accomplished by comparing the Mn 2p core electron binding energies and the Mn 3s multiplet splitting values with the results for a variety of manganese oxides.     

The effect of silica and natural organic matter on the Fe(II)-catalysed transformation and reactivity of Fe(III) minerals

The Fe(II)-catalysed transformation of synthetic schwertmannite, ferrihydrite, jarosite and lepidocrocite to more stable, crystalline Fe(III) oxyhydroxides is prevented by high, natural concentrations of Si and natural organic matter (NOM). Adsorption isotherms demonstrate that Si adsorbs to the iron minerals investigated and that increasing amounts of adsorbed Si results in a decrease in isotope exchange between aqueous Fe(II) and the Fe(III) mineral. This suggests that the adsorption of Si inhibits the direct adsorption of Fe(II) onto the mineral surface, providing an explanation for the inhibitory effect of Si on the Fe(II)-catalysed transformation of Fe(III) minerals. During the synthesis of lepidocrocite and ferrihydrite, the presence of equimolar concentrations of Si and Fe resulted in the formation of 2-line ferrihydrite containing co-precipitated Si in both cases. Isotope exchange experiments conducted with this freeze-dried Si co-precipitated ferrihydrite species (Si-ferrihydrite) demonstrated that the rate and extent of isotope exchange between aqueous Fe(II) and solid ⁵⁵Fe(III) was very similar to that of 2-line ferrihydrite formed in the absence of Si and which had not been allowed to dry. In contrast to un-dried ferrihydrite formed in the absence of Si, Si-ferrihydrite did not transform into a more crystalline Fe(III) mineral phase over the 7-day period of investigation. Reductive dissolution studies using ascorbic acid demonstrated that both dried Si-ferrihydrite and un-dried 2-line ferrihydrite were very reactive, suggesting these species may be major contributors to the rapid release of dissolved iron following flooding and the onset of conditions conducive to reductive dissolution in acid sulphate soil environments.     

Quantitative charge state analysis of manganese biominerals in aqueous suspension using scanning transmission X-ray microscopy (STXM)

We have applied Scanning Transmission Soft X-ray Microscopy (STXM) to investigate the charge state distribution of Mn in two kinds of Mn-biominerals, Mn nodules collected from Lake Michigan sediments and Mn precipitates formed by spores of a marine bacillus SG-1 under transport limited reaction conditions. A data analysis technique was developed, which allows for extraction of spatially resolved 2-d charge state maps of manganese on a submicron level. We find that the charge state of Mn dominates the spectral shape of L-edge spectra of environmentally important single oxidation state Mn minerals and that spectra of mixed oxidation state oxides can be modelled by a combination of appropriate single oxidation state reference spectra. Two-dimensional maps of charge state distributions clearly reveal domains of different oxidation states within single particles of Mn-micronodules. Spots of preferred accumulation of Mn(II) were found, which indicates biogenic precipitation of Mn(II)-species as a first step of nodule formation. The presence of Mn(III) in the studied sediment samples suggests the involvement of one-electron oxidation processes and reaction conditions which inhibit or slow down the disproportionation of Mn(III)-products. Under transport limited conditions, Mn oxidation products formed by spores of the marine bacillus SG-1 can vary from cell to cell. The presence of significant amounts of Mn(III) containing species points to the involvement of one-electron oxidation reactions as in the case of the micro-nodules. Our technique and the results obtained form a new basis for the mechanistic understanding of the formation of Mn biominerals in the environment.     

Biomineralization of lepidocrocite and goethite by nitrate-reducing Fe(II)-oxidizing bacteria: Effect of pH, bicarbonate, phosphate, and humic acids

Fe(III) solid phases are the products of Fe(II) oxidation by Fe(II)-oxidizing bacteria, but the Fe(III) phases reported to form within growth experiments are, at times, poorly crystalline and therefore difficult to identify, possibly due to the presence of ligands (e.g., phosphate, carbonate) that complex iron and disrupt iron (hydr)oxide precipitation. The scope of this study was to investigate the influences of geochemical solution conditions (pH, carbonate, phosphate, humic acids) on the Fe(II) oxidation rate and Fe(III) mineralogy. Fe(III) mineral characterization was performed using ⁵⁷Fe-Mössbauer spectroscopy and μ-X-ray diffraction after oxidation of dissolved Fe(II) within Mops-buffered cell suspensions of Acidovorax sp. BoFeN1, a nitrate-reducing, Fe(II)-oxidizing bacterium. Lepidocrocite (γ-FeOOH) (90%), which also forms after chemical oxidation of Fe(II) by dissolved O₂, and goethite (α-FeOOH) (10%) were produced at pH 7.0 in the absence of any strongly complexing ligands. Higher solution pH, increasing concentrations of carbonate species, and increasing concentrations of humic acids promoted goethite formation and caused little or no changes in Fe(II) oxidation rates. Phosphate species resulted in Fe(III) solids unidentifiable to our methods and significantly slowed Fe(II) oxidation rates. Our results suggest that Fe(III) mineralogy formed by bacterial Fe(II) oxidation is strongly influenced by solution chemistry, and the geochemical conditions studied here suggest lepidocrocite and goethite may coexist in aquatic environments where nitrate-reducing, Fe(II)-oxidizing bacteria are active.     

The natural attenuation of two acidic effluents in Tharsis and La Zarza-Perrunal mines (Iberian Pyrite Belt, Huelva, Spain)

The geochemical evolution of two acid mine effluents in Tharsis and La Zarza-Perrunal mines (Iberian Pyrite Belt, Huelva, Spain) has been investigated. In origin, these waters present a low pH (2.2 and 3.1) and high concentrations of dissolved sulphate and metals (Fe, Al, Mn, Cu, Zn, As, Cd, Co, Cr, Ni). However, the natural evolution of these acidic waters (which includes the bacterial oxidation of Fe(II) and the subsequent precipitation of Fe(III) minerals) represents an efficient mechanism of attenuation. This self-mitigating process is evidenced by the formation of schwertmannite, which retains most of the iron load and, by sorption, toxic trace elements like As. The later mixing with pristine waters rises the pH and favours the total precipitation of Fe(III) at pH 3.5 and, subsequently, Al compounds at pH 4.5, along with the sorption of trace metals (Mn, Zn, Cu, Cd, Co, Ni) until chemical equilibrium at circumneutral conditions is achieved.