An improved calibration for tethered balloon wind measurements

A previously published technique for using tethered spherical balloons as anemometers for measuring light low-level winds has been further developed. Earlier data on the relationship between the aerodynamic drag coefficient and the Reynolds number of spherical rubber balloons were combined with a large number of new data and re-analysed; and the errors in the relationship were estimated. The results allowed a more accurate calculation of wind speed from the deflection of a tethered balloon from the vertical. When combined with a new technique for calculating the effects of the tether, this enabled light to moderate low-level winds at fixed heights up to 600 m or more to be measured with simple, cheap, and readily mobile equipment; and a slight modification of the technique allowed measurement of winds in and above fog. Wind speeds measured by the ballon technique showed reasonably good agreement with measurements by an anemometer carried beneath the balloon.Glossary of Symbols a, b, c Coefficients in the relationship between lnC _d and lnR - A Quantity under square root in solution for lnV whena0 - C _d Wind drag coefficient for balloon - C _dc Value ofC _d given by calibration curve of Table I - D Dynamic wind pressure force on balloon - F Buoyant free lift of balloon with load - Re Reynold's number of balloon (sphere) - R = Re/10⁵ - r Radius of sphere - T Tension in tether - V Wind speed - ₈₃() =(lnC _dc -lnC _d ) when 83° , or 0 for other - Error in lnC _d - Elevation of tether where attached to balloon - Elevation of balloon from ground tether point - Molecular viscosity of air - Ratio of circumference to diameter of circle - Density of air     

On the mean monthly equivalent potential temperature and rainfall in West Africa

Summary Rainfall in West Africa is examined in relation to monthly mean equivalent potential temperature ( _e )at the earth's surface. The study revealed that monthly mean equivalent potential temperature ( _e ) and monthly rainfall (R) generally decreased northwards from the equator.A good relationship existed betweenR and _e in the northern zone of West Africa (i.e., north of 7.5° N). No definite relationship existed in the southern zone. In the northern zone, the departure of _e from its annual mean ( ) first became positive about a month before the onset of the rains. Positive departures from ) generally resulted in more than normal (or average) rainfall in this zone. In general, little or no rainfall occurred in West Africa whenever _e was less than 320 K.

---

Zusammenfassung Der Niederschlag (MonatssummeR) in Westafrika wird in Zusammenhang mit der mittleren monatlichen Äquivalent-temperatur ( _e ) an der Erdoberfläche untersucht. Es zeigte sich, daß die Monatswerte beider Elemente im allgemeinen vom Äquator nach Norden abnehmen.ZwischenR und _e ergab sich für das nördliche Westafrika (nördlich von 7.5° N) eine gute, für die südliche Zone jedoch keine beweisbare Übereinstimmung. In der nördlichen Zone übertraf _e das Jahresmittel erstmals etwa einen Monat vor Beginn der Regenzeit. Positive Abweichungen vom mittleren _e hatten immer übernormalen Niederschlag in dieser Zone zur Folge. Dagegen gab es wenig oder keinen Niederschlag in Westafrika, wenn _e unter 320 K lag.

---

---

With 7 Figures     

Third- and fourth-order mixed moments of turbulent velocity and temperature fluctuations in the atmospheric surface layer

Fourth-order mixed moments of velocity and temperature fluctuations, measured within the atmospheric surface layer, are compared with results obtained by assuming the quasi-Gaussian approximation. Standard deviations of the products uw, u and w(u and w are the longitudinal and vertical velocity fluctuations; is the temperature fluctuation) are in good agreement with those obtained using the quasi-Gaussian assumption. Good agreement is also obtained between measured and Gaussian estimates of fourth-order moments including all three fluctuations u, w, Schwarz inequalities, commonly used in the clipping approximation in turbulence modelling, are found to provide bounds for third-order moments of w, that are too conservative. More reasonable, tighter, bounds for these moments are given by inequalities obtained by Lumley.     

Approximate Solutions For The Obukhov Length And The Surface Fluxes In Terms Of Bulk Richardson Numbers

Simple analytic approximate solutions arepresented for the set of equations that follows fromthe Monin–Obukhov flux-profile relationships using thestability functions of Dyer (unstable case) andBeljaars–Holtslag (stable case). Several publicationsare devoted to the same subject, however the currentapproach contains some new features, namely: (a) itappears to be more accurate for unstable situationsand (b) it applies also to the general case where windspeed (u) and potential temperature() are given at different levels. In order toillustrate the accuracy of the approach a comparisonwith the actual solutions is presented for someselected combinations of and u levelstypical for various practical applications.     

Properties of spatial temperature derivatives in the atmospheric surface layer

A pair of parallel cold wires separated in either the vertical or lateral direction was used to obtain the three components _x, _y, _z of the temperature derivative in the streamwise, lateral and vertical directions, respectively. The average absolute skewness values of _x and _z are nonzero and approximately equal, while the skewness of _y is approximately zero. These results appear to be consistent with the presence of a large, three-dimensional organised structure in the surface layer. There is an apparent low-frequency contamination in the spectral density of _y and _z due mainly to small errors in estimating the sensitivity of the cold wires. The temperature derivatives were high-pass filtered, the filter being set to remove possible contributions from the large structure and to minimise low-frequency sensitivity contamination. The filtered rms ratios \~_x/\~_y and \~_x/\~_z were in the range 0.7 to 0.9, a result in qualitative agreement with that obtained in the laboratory boundary layer by Sreenivasan et al. (1977). The skewness of filtered _x or _z is negligible, consistent with local isotropy of small-scale temperature fluctuations and in support of the high wavenumber spectral isotropy discussed in Antonia and Chambers (1978).     

Local similarity of spectral and cospectral characteristics in the stable-continuous boundary layer

The local similarity theory, presented in the recent papers of Sorbjan (1986a, b), is extended by taking into consideration spectral (u, v, w, ) and cospectral (uw, w, u) densities in the stable-continuous boundary layer. The resulting universal expressions for spectra, cospectra and the reduced frequencies of their peaks are in agreement with empirical data from the Kansas 1968 surface-layer and Minnesota 1973 boundary-layer experiments. In addition, the universal functions for the structure parameters and the dissipation rates are also derived and shown to fit the empirical data well.On leave from Institute of Environmental Engineering, Warsaw Polytechnic University, 00653 Warsaw, Poland.     

Similarity of atmospheric Reynolds shear stress and heat flux fluctuations over a rough surface

Horizontal u and vertical w velocity fluctuations have been measured together with temperature fluctuations in the atmospheric surface layer, at a small height above a wheat crop canopy. Marginal probability density functions are presented for both individual fluctuations u, w, and for the instantaneous Reynolds stress uw, and heat fluxes w and u. Probability density functions of the velocity fluctuations deviate less significantly from the Gaussian form than the probability density of temperature. There appears to be closer similarity between statistics of the instantaneous heat fluxes than between the momentum flux and either of the heat fluxes investigated. The mean momentum flux receives equal contributions from the events referred to as ejections and sweeps in laboratory boundary layers. Sweeps provide the largest contribution to the heat fluxes.     

Diurnal variation of horizontal wind direction fluctuations in complex terrain at Geysers,Cal.

Horizontal diffusion in the surface layer is dependent on the standard deviation of wind direction fluctuations . Diurnal variation of this parameter in complex terrain was studied for the July 1979 Geysers, Cal., experiment using data from a network of 11 short meteorological towers in the 25 km² Anderson Creek watershed Valley side slopes are roughly 20 ° and maximum terrain difference is about 1 km.Values of for wind directions sampled for one hour at a height of 10 m are about 35 ° during the daytime. They slowly decrease to about 20 ° by 8 to 10 p.m. as stability increases but wind speeds are still relatively high. After 10 p.m. the drainage flow sets in at most stations, with speeds of 1 to 2 m s^-1, and average increases to about 30° during the period 11 p.m. to 6 a.m. In general, highest values of at night are associated with lowest values of wind speed and greatest static stability. This enhancement of by the terrain suggests that horizontal diffusion at night always conforms to that expected during nearly neutral stabilities. That is, Pasquill class D diffusion applies to the horizontal component all night in complex terrain.     

The stably stratified internal boundary layer for steady and diurnally varying offshore flow

A two-dimensional numerical mesoscale model is used to investigate the internal structure and growth of the stably stratified internal boundary layer (IBL) beneath warm, continental air flowing over a cooler sea. Two situations are studied — steady-state and diurnally varying offshore flow. In the steady-state case, vertical profiles of mean quantities and eddy diffusion coefficients (K) within the IBL show small, but significant, changes with increasing distance from the coast. The top of the IBL is well defined, with large vertical gradients within the layer and a maximum in the coast-normal wind component near the top. Well away from the coast, turbulence, identified by non-zero K, decreases to insignificant levels near the top of the IBL; the IBL itself is characterised by a critical value of the layer-flux Richardson number equal to 0.18. The overall behaviour of the mean profiles is similar to that found in the horizontally homogeneous stable boundary layer over land.A simple physical model is used to relate the depth of the layer h to several relevant physical parameters viz., x, the distance from the coast and U, the large-scale wind (both normal to the coastline) and g/, being the temperature difference between continental mixed-layer air and sea surface, is the mean potential temperature and g is the acceleration due to gravity. Excellent agreement with the numerical results is found, with h = 0.014x ^1/2 U (g/)^–1/2.In the diurnally varying case, the mean profiles within the IBL show only small differences from the steady-state case, although diurnal variations, particularly in the wind maximum, are evident within a few hundred kilometres of the coast. A mesoscale circulation normal to the coast, and superimposed upon the mean offshore flow, develops seawards of the coastline with maximum vertical velocities about sunset, of depth about 2 km and horizontal scale 500 km. The circulation is related to the advection, and subsequent decay, of daytime convective turbulence over the sea.     

Observed variations of σθ and σΦ in the nocturnal drainage flow in a deep valley

The variations of and in the drainage flow in the Brush Creek valley of western Colorado are investigated using data from Doppler acoustic sodars and instrumented towers. The data were obtained on two experimental nights during the 1984 ASCOT field study. There is good agreement between the variations derived from low-level observations of the sodars and those derived from the towers located throughout the valley. The observed hourly average and in the nocturnal drainage flow are about 20 ° to 25 ° and 5 °, respectively; these values are much larger than those generally observed over flat terrain during nighttime stable conditions. After sunrise (about 0600 MST), as the valley warms and the flow direction changes to up-valley, these parameters increase sharply to their peak values at about 0800 MST and then decrease to their normal daytime values after about two hours.In the drainage flow, the hourly average varies inversely with wind speed according to the relation u 0.7ms^-1. The vertical standard deviation is much less enhanced by complex terrain than the horizontal standard deviation. The observed values are predicted fairly well by the local similarity theory.Oak Ridge Associated Universities (ORAU) Summer Research Participant at ATDD in 1987 andOak Ridge Associated Universities (ORAU) Summer Research Participant at ATDD in 1987 and     

Eddy flux measurements over the ocean and related transfer coefficients

Eddy correlation measurements of vertical turbulent fluxes made during AMTEX 1975 are used to assess the reliability of flux prediction from established bulk transfer relations, using both surface-layer and planetary boundary-layer formulations. The surface-layer formulae predict momentum and latent heat fluxes to an accuracy comparable to the direct eddy correlation method, using transfer coefficients of C _DN (at 10m and in neutral conditions) increasing with wind speed, and a constant C _EN - 1.5 × 10 ^–3 . The data suggest C _CHN , for sensible heat, increases significantly with wind speed and is on average 30% lower than C _CEN The boundary-layer drag coefficient, C _GD , agrees within about 40% of recently published values using a vertically averaged geostrophic wind to the height of the lowest temperature inversion, corrected for trajectory curvature. Values of _* / from which C _CGH is derived, are in excellent agreement if the published values are modified to account for inappropriate surface temperatures used in their derivation. Preliminary values of C _GE are also presented.     

The use of σ T as a temperature scale in the atmospheric surface layer

The standard deviation of temperature _T is proposed as a temperature scale and as a velocity scale to describe the behaviour of turbulent flows in the Atmospheric Surface Layer (ASL), instead of _* andu _* of the Monin—Obukhov similarity theory, and ofT _f andU _f used for free convection stability conditions. On the basis of experimental evidence reported in the literature, it is shown that _T T _f andv _* U _f in the free convection region, and _{T *} andv _* U _* in nearneutral and stable conditions. This implies that the proposed scales can be applied for all stabilities. Furthermore, a new length scale is proposed and its relation with Obukhov length is given. Also, a simple semi-empirical expression is presented with which _T andv _* can be evaluated in a rather simple way. Some examples of practical applications are given, e.g., a stability classification for unstable conditions.     

A statistical-dynamical downscaling procedure for global climate simulations

Summary A statistical-dynamical downscaling procedure for global climate simulations is described. The procedure is based on the assumption that any regional climate is associated with a specific frequency distribution of classified large-scale weather situations. The frequency distributions are derived from multi-year episodes of low resolution global climate simulations. Highly resolved regional distributions of wind and temperature are calculated with a regional model for each class of large-scale weather situation. They are statistically evaluated by weighting them with the according climate-specific frequency. The procedure is exemplarily applied to the Alpine region for a global climate simulation of the present January climate.List of Symbols west-east mesh size in geographic coordinates south-north mesh size in geographic coordinates N number of large-scale weather classes n number of regional-scale event classes p pressure P probability Ø large-scale event regional-scale event q _v specific humidity potential temperature u west-east wind component v south-north wind componentAbbreviations AGL above ground level - LT local time - UTC universal time coordinated With 13 Figures     

The prediction of dust erosion by wind: An interactive model

We have devised a partial differential equation for the prediction of dust concentration in a thin layer near the ground. In this equation, erosion (detachment), transport, deposition and source are parameterised in terms of known quantities. The interaction between a wind prediction model in the boundary layer and this equation affects the evolution of the dust concentration at the top of the surface layer. Numerical integrations are carried out for various values of source strength, ambient wind and particle size. Comparison with available data shows that the results appear very reasonable and that the model should be subjected to further development and testing.Notation (x, y, z, t) space co-ordinates and time (cm,t) - u, v components of horizontal wind speed (cm s^–1) - u _g, v_g components of the geostrophic wind (cm s^–1) - V=(u²+v²)^1/2 (cm s^–1) - (û v)= 1/(h – k) _k ^h(u, v)dz(cm s^–1) - V _* friction velocity (cm s^–1) - z ₀ roughness length (cm) - k ₁ von Karman constant =0.4 - V _d deposition velocity (cm s^–1) - V _g gravitational settling velocity (cm s^–1) - h height of inversion (cm) - k height of surface layer (cm) - potential temperature (°K) - _gr potential temperature at ground (°K) - _K potential temperature at top of surface layer (°K) - P pressure (mb) - P ₀ sfc pressure (mb) - C _p/C_v - (t)= /z lapse rate of potential temperature (°K cm^–1) - A(z) variation of wind with height in transition layer - B(z) variation of wind with height in transition layer - Cd drag coefficient - C _HO transfer coefficient for sensible heat - C dust concentration (g m^–3) - C _K dust concentration at top of surface layer (g m^–3) - D(z) variation with height of dust concentration - u, v, w turbulent fluctuations of the three velocity components (cm s^–1) - A ₁ constant coefficient of proportionality for heat flux =0.2 - Ri Richardson number - g gravitational acceleration =980 cm s^–2 - Re Reynolds number = - D _s thickness of laminar sub-layer (cm) - v molecular kinematic viscosity of air - coefficient of proportionality in source term - dummy variable - t time step (sec) - n time index in numerical equations On sabbatical leave at University of Aberdeen, Department of Engineering, September 1989–February 1990.     

Determination of similarity functions of the resistance laws for the planetary boundary layer using surface-layer similarity functions

Functional forms of the universal similarity functions A, B (for wind components parallel and normal to the surface stress), and C (for potential temperature difference) are determined based on the generalized theory of the resistance laws for the Planetary Boundary Layer (PBL). The similarity-profile functions for the surface layer are matched with the velocity and temperature-defect profiles that are assumed to have shapes modified by certain powers of nondimensional height z/h, where h is the PBL height. The powers of the outer-layer profile functions are determined, so that the functions become negligible in the surface layer. To close the temperature defect law, an assumption that the temperature gradient across the top of the PBL is continuous with the stratification of the overlying atmosphere is used. The result of this assumption is that nondimensional momentum and temperature profiles in the PBL can be described in terms of four basic ratios: (1) roughness ratio = /h (2) scale-height ratio =|f|h/u_*, (3) ambient stratification parameter =h/_*, and (4) stability parameter =h/L, where L is the Monin-Obukhov length, z₀ is the surface roughness, is the upper-air stratification, u _* is the friction velocity, and _* is the temperature scale at the surface. For stable conditions, the scale-height ratio can be related to the atmospheric stability and the upperair stratification, and the generalized similarity and Rossby number similarity theories become identical. Under appropriate boundary conditions, function A is explicitly dependent on the stability parameter , while B is a function of scale-height ratio , which in turn depends on the stability. Function C is shown to be dependent on the stability and the upper-air stratification, due to the closure assumption used for the temperature profile.The suggested functional forms are compared with other empirical approximations by several authors. The general framework used to determine the functional forms needs to be tested against good boundary-layer measurements.     

Seasonal variation of Σθ with wind speed,direction and stability

For an airport site near Visakhapatnam, India, and based on 10 years of data for the months of January, April, August and October, values of are given as a function of wind speed, wind direction and Pasquill diffusion category.     

On Trajectory Curvature as a Selection Criterion for Valid Lagrangian Stochastic Dispersion Models

Recently Wilson and Flesch (Boundary-Layer Meteorology, 84, 411-426, 1997) suggested that the average increment d z to the orientation = arctan(w/u) of the Lagrangian velocity-fluctuation vector can be used to distinguish the better Lagrangian stochastic models within the well-mixed class. Here it is demonstrated that the specification of d z constitutes neither a sufficient or universally applicable criterion to distinguish the better Lagrangian stochastic models within the well-mixed class. The hypothesis made by Wilson and Flesch that Lagrangian stochastic models with /P_E irrotational are zero-spin models, having d z=0, is proven     

Turbulence mechanisms at an agricultural site

An extensive set of turbulence data from the 3- and 12-m heights taken over an agricultural site (Marsta, Sweden) are analyzed and compared with data from ideal sites.In unstable air, Monin-Obukhov similarity is found to be valid for the non-dimensional gradients of wind, _m , temperature, _h , and humidity, _e , for (only a few data), for _T /|T _*|,/ _E /|E _*| and for the non-dimensionalized inertial subrange spectra of temperature and humidity. Where comparison is possible, the unstable data also agree with those found in the Kansas study, with one remarkable exception, the inertial subrange constant of the temperature spectrum, ₁, being only 0.39, compared to the value 0.80 found at the Kansas site.On the stable side, most similarity predictions break down, with most of the data differing systematically from the corresponding Kansas results, the only exception being . The inertial subrange constants for temperature, ₁, and for humidity, ₁ are found to have the same values, 0.39 and 0.30, respectively, as they do on the unstable side. Remarkable similarity is found for the shape of the stable u- and - and e-spectra. In addition, this shape is found to be identical with that found in Kansas. The peak wavelength of the stable u-, and -spectra is found to be about four times larger than it is for the corresponding Kansas spectra. This is interpreted to be a result of the increased macro-roughness at the Marsta site as compared with that at the Kansas site. A possible explanation for the low ₁-value is discussed, suggesting that ₁ is not a universal constant, but instead dependent on the turbulent structure.     

Inferring the thermal-infrared hemispheric emission from a sparsely-vegetated surface by directional measurements

The thermal-infrared (longwave) emission from a vegetated terrain is generally anisotropic, i.e., the emission temperature varies with the view direction. If a directional measurement of temperature is considered to be equal to the effective temperature of the hemispheric emission, then the estimate of the latter can be significantly in error. The view-direction (zenith angle _eq ) at which the emission equivalence does hold is determined in our modeling study. In a two-temperature field-of-view (soil and plants), _eq falls in a narrow range depending on plant density and canopy architecture. _eq does not depend on soil and (uniform) plant temperatures nor on their ratio, even though the pattern of emission vs. the view direction depends crucially on this ratio. For a sparse canopy represented as thin, vertical cylindrical stalks (or vertical blades uniformly distributed in azimuth) with horizontal facets, _eq ranges from 48 to 53° depending on the optical density of the vertical elements alone. When plant elements are modeled as small spheres, _eq lies between 53 to 57° (for the same values of the canopy optical density). Only for horizontal leaves (a truly planophile canopy) is the temperature measured from any direction equal to the temperature of the hemispheric emission. When the emission temperature changes with optical depth within the canopy at a specified rate, _eq depends to some extent on that rate. For practically any sparsely vegetated surface, a directional measurement at the zenith angle of 50° offers an appropriate evaluation of the hemispheric emission, since the error in the estimate will, at most, only slightly exceed 1% (around 4 W m^–2). Estimates of the hemispheric emission through a nadir measurement, on the other hand, can be in error in some cases by about 10%, i.e., on the order of 40 W m^–2....by a small sample we may judge the whole piece... Miguel de Cervantes, 1605, inDon Quixote de la Mancha, Pt. I, Ch. 4     

Observation of lake breeze penetration and subsequent development of the thermal internal boundary layer for the Nanticoke II Shoreline Diffusion Experiment

The turbulent structure of the lake breeze penetration and subsequent development of the thermal internal boundary layer (TIBL) was observed using a kytoon-mounted ultrasonic anemometer-thermometer. The lake breeze penetrated with an upward rolling motion associated with the upward flow near the lake breeze front. After the lake breeze front passed, the behaviors of the velocity and temperature at the top of the lake breeze layer were similar to those found in convective boundary layers (CBL). Comparing _gq/_*, _u /w _* and _w /w _* between the present observation of TIBL development after the passage of the lake breeze front and CBL data from the literature, the /_* values showed reasonable agreement; however, _u /w _* and _w /W_* had smaller values in the TIBL than in the CBL at higher altitudes. This is due to the differences in the mean velocity profiles. While the CBL has a uniform velocity profile, the TIBL has a peak at lower elevation due to the lake breeze penetration; the velocity then decreases with height.Present address: The Institute of Behavioral Science, 1-35-7 Yoyogi, Tokyo 151, Japan.