Geochemistry and isotopes of fluids from sulphur springs, Valles Caldera, New Mexico

Detailed geochemistry supported by geologic mapping has been used to investigate Sulphur Springs, an acid-sulfate hot spring system that issues from the western flank of the resurgent dome inside Valles Caldera. The most intense activity occurs at the intersection of faults offsetting caldera-fill deposits and post-caldera rhyolites. Three geothermal wells in the area have encountered pressures <1 MPa and temperatures of 200°C at depths of 600 to 1000 m. Hot spring and fumarole fluids may discharge at boiling temperatures with pH 1.0 and SO₄ 8000 mg/l. These conditions cause argillic alterations throughout a large area.Non-condensible gases consist of roughly 99% CO₂ with minor amounts of H₂S, H₂, and CH₄. Empirical gas geothermometry suggests a deep reservoir temperature of 215 to 280°C. Comparison of ¹³C and ¹⁸O between CaCO₃ from well cuttings and CO₂ from fumarole steam indicates a fractionation temperature between 200 and 300°C by decarbonation of hydrothermally altered Paleozoic limestone and vein calcite in the reservoir rocks. Tritium concentrations obtained from steam condensed in a mudpot and deep reservoir fluids (Baca #13, 278°C) are 2.1 and 1.0 T.U. respectively, suggesting the steam originates from a reservoir whose water is mostly >50 yrs old. Deuterium contents of fumarole steam, deep reservoir fluid, and local meteoric water are practically identical even though ¹⁸O contents range through 4‰, thus, precipitation on the resurgent dome of the caldera could recharge the hydrothermal system by slow percolation. From analysis of D and ¹⁸O values between fumarol steam and deep reservoir fluid, steam reaches the surface either (1) by vaporizing relatively shallow groundwater at 200°C or (2) by means of a two-stage boiling process through an intermediate level reservoir at roughly 200°C.Although many characteristics of known vapor-dominated geothermal systems are found at Sulphur Springs, fundamental differences exist in temperature and pressure of our postulated vapor-zone. We propose that the reservoir beneath Sulphur Springs is too small or too poorly confined to sustain a “true” vapor-dominated system and that the Sulphur Springs system may be a “dying” vapor-dominated system that has practically boiled itself dry.     

Thermal areas on Kilauea and Mauna Loa Volcanoes, Hawaii

Active thermal areas are concentrated in three areas on Mauna Loa and three areas on Kilauea. High-temperature fumaroles (115–362° C) on Mauna Loa are restricted to the summit caldera, whereas high-temperature fumaroles on Kilauea are found in the upper East Rift Zone (Mauna Ulu summit fumaroles, 562° C), middle East Rift Zone (1977 eruptive fissure fumaroles), and in the summit caldera. Solfataric activity that has continued for several decades occurs along border faults of Kilauea caldera and at Sulphur Cone on the southwest rift zone of Mauna Loa. Solfataras that are only a few years old occur along recently active eruptive fissures in the summit caldera and along the rift zones of Kilauea. Steam vents and hot-air cracks also occur at the edges of cooling lava ponds, on the summits of lava shields, along faults and graben fractures, and in diffuse patches that may reflect shallow magmatic intrusions.     

Geological evolution of a pleistocene rhyolitic center — Sierra La Primavera, Jalisco, México

The Sierra La Primavera volcanic complex consists of late Pleistocene comenditic lava flows and domes. ash-flow tuff, air-fall pumice, and cold caldera-lake sediments. The earliest lavas were erupted about 120,000 years ago, and were followed approximately 95,000 years ago by the eruption of about 20 km³ of magma as ash flows that form the compositionally-zoned Tala Tuff. Collapse of the roof zone of the magma chamber led to the formation of a shallow 11-km-diameter caldera. It soon filled with water, forming a caldera lake in which sediment began to collect. At about the same time, two central domes erupted through the middle of the lake and a “giant pumice horizon”, an important stratigraphic marker, was deposited. Shortly thereafter ring domes erupted along two parallel arcs: one along the northeast portion of the ring fracture, and the other crossing the middle of the lake. All these events occurred during a period of approximately 5,000–10,000 years. Sedimentation continued and a period of volcanic quiescence was marked by the deposition of some 30 m of fine-grained ashy sediments virtually free from pumice lapilli. Approximately 75,000 years ago, a new group of ring domes erupted at the southern margin of the lake. These domes are lapped by only 10–20 m of sediments, as uplift resulting from renewed insurgence of magma brought an end to the lake. This uplift culminated in the eruption, beginning approximately 60,000 years ago, of aphyric lavas along a southern arc. The youngest of these lavas erupted approximately 20,000–30,000 years ago.The four major fault systems in the Sierra La Primavera are related to caldera collapse or to uplift caused by the insurgence of the southern are magma. Steam vents and larga-discharge 65°C hot springs are associated with the faulting. Calculated equilibrium temperatures of the geothermal fluids are 170°C, but temperatures in excess of 240°C have been encountered in an exploratory drill hole.A seismic survey showed attenuation of both S and P waves within the caldera, P waves attenuated more severely than S waves. The greatest attenuation is associated with an area of steam vents, and the rapid lateral variations in attenuation suggest that they are produced by a shallow geothermal system rather than by underlying magma.     

Guagua pichincha volcano, Ecuador: fluid geochemistry in volcanic surveillance

The densely populated metropolitan area of Quito is located on the slopes of the active Guagua Pichincha volcano at only 10 km from the crater. Recently, the Italian Ministry of Foreign Affairs sponsored a project for the mitigation of volcanic hazard in this area. The geochemical study carried out as part of this project was aimed at constructing a geochemical model of the zone for use in volcanic surveillance.According to this geochemical model, a hydrothermal aquifer (T = 200–240°C), fed both by meteoric waters and by fluids released by a magma body, lies at shallow levels beneath Guagua Pichincha crater. The crater fumaroles are essentially fed by steam boiled off from the hydrothermal aquifer. The high flow rate fumaroles located in the dome area show significant SO₂ contents, which suggest a relatively high contribution of magmatic fluids in the zone of the aquifer feeding them. The absence of SO₂ in the fumarolic discharges near the southern crater wall indicates instead that the magmatic fluids dissolve entirely into the aquifer here. The hot springs located at the western end of the crater represent the lateral discharge of the hydrothermal aquifer.On the basis of this model, it is likely that an increment in the flux of both the magmatic fluids and the heat from a magma body produces an increase, albeit small, of the pressure-temperature conditions of the hydrothermal system and consequent changes in flow rate and fluid chemistry of the fumarolic vents. In particular, total sulphur and possibly hydrochloric acid may increase in all the vents and sulphur dioxide may appear in other fumarolic discharges. The varying thermodynamic conditions in the hydrothermal aquifer can be evaluated on the basis of the equilibria among carbon species and hydrogen. Only minor delayed changes are expected in the physical-chemical characteristics of the springs located at the western end of the crater.     

Geology of the platanares geothermal area, Departamento de Copán, Honduras

The Platanares geothermal area, Departamento de Copán, Honduras, is located within a graben that is complexly faulted. The graben is bounded on the north by a highland composed of Paleozoic (?) metamorphic rocks in contact with Cretaceous - Tertiary redbeds of unknown thickness. These are unconformably overlain by Tertiary andesitic lavas, rhyolitic ignimbrites, and associated sedimentary rocks. The volcanic rocks are mostly older than 14 Ma, and thus are too old to represent the surface expression of an active crustal magma body. Thermal fluids that discharge in the area are heated during deep circulation of meteoric water along faults in a region of somewhat elevated heat flow. Geothermometry based upon the chemical composition of thermal fluids from hot springs and from geothermal gradient coreholes suggests that the reservoir equilibrated at temperatures as high as 225 to 240°C, within the Cretaceous redbed sequence. Three continuously cored geothermal gradient holes have been drilled; fluids of about 165°C have been produced from two drilled along a NW-trending fault zone, from depths of 250 to 680 m. A conductive thermal gradient of 139°C/km, at a depth of 400 m, was determined from the third well, drilled 0.6 km west of that fault zone. These data indicate that the Platanares geothermal area holds considerable promise for electrical generation by moderate- to hightemperature geothermal fluids.     

Geology, water geochemistry and geothermal potential of the jemez springs area, Canon de San Diego, new Mexico

Studies of the geology, geochemistry of thermal waters, and of one exploratory geothermal well show that two related hot spring systems discharge in Canõn de San Diego at Soda Dam (48°C) and Jemez Springs (72°C). The hot springs discharge from separate strands of the Jemez fault zone which trends northeastward towards the center of Valles Caldera. Exploration drilling to Precambrian basement beneath Jemez Springs encountered a hot aquifer (68°C) at the top of Paleozoic limestone of appropriate temperature and composition to be the local source of the fluids in the surface hot springs at Jemez Springs. Comparisons of the soluble elements Na, Li, Cl, and B, arguments based on isotopic evidence, and chemical geothermometry indicate that the hot spring fluids are derivatives of the deep geothermal fluid within Valles Caldera. No hot aquifer was discovered in or on top of Precambrian basement. It appears that low- to moderate-temperature geothermal reservoirs (< 100°C) of small volume are localized along the Jemez fault zone between Jemez Springs and the margin of Valles Caldera.     

Hydrogeochemistry of the Simav geothermal field, western Anatolia, Turkey

Thermal waters hosted by Menderes metamorphic rocks emerge along fault lineaments in the Simav geothermal area. Thermal springs and drilled wells are located in the Eynal, Çitgöl and Na a locations, which are part of the Simav geothermal field. Studies were carried out to obtain the main chemical and physical characteristics of thermal waters. These waters are used for heating of residences and greenhouses and for balneological purposes. Bottom temperatures of the drilled wells reach 163°C with total dissolved solids around 2225 mg/kg. Surface temperatures of thermal springs vary between 51°C and 90°C. All the thermal waters belong to Na–HCO₃–SO₄ facies. The cold groundwaters are Ca–Mg–HCO₃ type. Dissolution of host rock and ion-exchange reactions in the reservoir of the geothermal system shift the Ca–Mg–HCO₃ type cold groundwaters to the Na–HCO₃–SO₄ type thermal waters. Thermal waters are oversaturated at discharge temperatures for aragonite, calcite, quartz, chalcedony, magnesite and dolomite minerals giving rise to a carbonate-rich scale. Gypsum and anhydrite minerals are undersaturated with all of the thermal waters. Boiling during ascent of the thermal fluids produces steam and liquid waters resulting in an increase of the concentrations of the constituents in discharge waters. Steam fraction, y, of the thermal waters of which temperatures are above 100°C is between 0.075 and 0.119. Reservoir pH is much lower than pH measured in the liquid phase separated at atmospheric conditions, since the latter experienced heavy loss of acid gases, mainly CO₂. Assessment of the various empirical chemical geothermometers and geochemical modelling suggest that reservoir temperatures vary between 175°C and 200°C.     

Geochemistry and geothermometry of spring water from the Blackfoot Reservoir region, southeastern Idaho

The Blackfoot Reservoir region in southeastern Idaho is recognized as a potential geothermal area because of the presence of several young rhyolite domes (50,000 years old), Quaternary basalt flows, and warm springs. North- to northwest-trending high-angle normal faults of Tertiary to Holocene age appear to be the dominant structural control of spring activity. Surface spring-water temperatures average 14°C except for a group of springs west of the Reservoir Mountains which average 33°C. Chemical geothermometers applied to fifty water samples give temperatures less than 75°C except for eight springs along the Corral Creek drainage. The springs along Corral Creek have Na-K-Ca temperatures that average 354°C, a direct result of high potassium concentrations in the water. A correction for carbon dioxide applied to the Na-K-Ca geothermometer lowers the estimated temperatures of the anomalous springs to near the measured surface temperatures, and Na-K-Ca-Mg temperatures for the anomalous springs are near 100°C. Mixing model calculations suggest that hot water with a temperature of approximately 120°C may be mixing with cooler, more dilute water in the springs from the Corral Creek drainage, a temperature supported by Na-K-Ca-Mg temperatures and mineral saturation temperatures.Stability relations of low-temperature phases in the system indicate that the large concentrations of potassium in the eight anomalous springs are derived from reactions with the potassium-bearing minerals muscovite and K-feldspar. Carbon dioxide and hydrogen sulfide gases may be derived through the oxidation of organic matter accompanied by the reduction of sulfate. Concentrations of major and minor elements, and gases found in springs of the Blackfoot Reservoir region are due to water-rock reactions at temperatures less than 100°C.Based on spring geochemistry, a geothermal reservoir of 100°C up to 120°C may exist at shallow (less than 2 km) depths in the Blackfoot Reservoir region.     

Geochemistry of the thermal springs and fumaroles of Basse-Terre Island,Guadeloupe, Lesser Antilles

 The purpose of this work was to study jointly the volcanic-hydrothermal system of the high-risk volcano La Soufrière, in the southern part of Basse-Terre, and the geothermal area of Bouillante, on its western coast, to derive an all-embracing and coherent conceptual geochemical model that provides the necessary basis for adequate volcanic surveillance and further geothermal exploration. The active andesitic dome of La Soufrière has erupted eight times since 1660, most recently in 1976–1977. All these historic eruptions have been phreatic. High-salinity, Na–Cl geothermal liquids circulate in the Bouillante geothermal reservoir, at temperatures close to 250  °C. These Na–Cl solutions rise toward the surface, undergo boiling and mixing with groundwater and/or seawater, and feed most Na–Cl thermal springs in the central Bouillante area. The Na–Cl thermal springs are surrounded by Na–HCO₃ thermal springs and by the Na–Cl thermal spring of Anse à la Barque (a groundwater slightly mixed with seawater), which are all heated through conductive transfer. The two main fumarolic fields of La Soufrière area discharge vapors formed through boiling of hydrothermal aqueous solutions at temperatures of 190–215  °C below the "Ty" fault area and close to 260  °C below the dome summit. The boiling liquid producing the vapors of the Ty fault area has δD and δ¹⁸O values relatively similar to those of the Na–Cl liquids of the Bouillante geothermal reservoir, whereas the liquid originating the vapors of the summit fumaroles is strongly enriched in ¹⁸O, due to input of magmatic fluids from below. This process is also responsible for the paucity of CH₄ in the fumaroles. The thermal features around La Soufrière dome include: (a) Ca–SO₄ springs, produced through absorption of hydrothermal vapors in shallow groundwaters; (b) conductively heated, Ca–Na–HCO₃ springs; and (c) two Ca–Na–Cl springs produced through mixing of shallow Ca–SO₄ waters and deep Na–Cl hydrothermal liquids. The geographical distribution of the different thermal features of La Soufrière area indicates the presence of: (a) a central zone dominated by the ascent of steam, which either discharges at the surface in the fumarolic fields or is absorbed in shallow groundwaters; and (b) an outer zone, where the shallow groundwaters are heated through conduction or addition of Na–Cl liquids coming from hydrothermal aquifer(s). Received: 9 November 1998 / Accepted: 15 July 1999     

Aquifer chemistry of the Puga and Chumatang high temperature geothermal systems in India

Results of a chemical study of the fluids from drill holes and hot springs of Puga and Chumatang areas in the northwestern part of the Himalaya are presented and discussed in this paper. The thermal waters of Puga and Chumatang are of Na-HCO₃-Cl and Na-HCO₃ types, respectively. A comparison between these waters, their chemical classification and activity studies suggest a flow path within a quartzitic-schistose basement, containing quartz, K-feldspar and illite, and in clayey terrains containing montmorillonite and illite.The chemistry of thermal waters also indicate their association with magmatic activity. The chemical geothermometers indicate the possible existence of a geothermal reservoir at Puga with temperature ≈250°C. The Chumatang area has a comparatively cooler reservoir with a temperature of 150–180°C.     

New evidence on the hydrothermal system in Long Valley caldera, California, from wells, fluid sampling, electrical geophysics, and age determinations of hot-spring deposits

Data collected since 1985 from test drilling, fluid sampling, and geologic and geophysical investigations provide a clearer definition of the hydrothermal system in Long Valley caldera than was previously available. This information confirms the existence of high-temperature (> 200°C) reservoirs within the volcanic fill in parts of the west moat. These reservoirs contain fluids which are chemically similar to thermal fluids encountered in the central and eastern parts of the caldera. The roots of the present-day hydrothermal system (the source reservoir, principal zones of upflow, and the magmatic heat source) most likely occur within metamorphic basement rocks beneath the western part of the caldera. Geothermometer-temperature estimates for the source reservoir range from 214 to 248°C. Zones of upflow of hot water could exist beneath the plateau of moat rhyolite located west of the resurgent dome or beneath Mammoth Mountain. Lateral flow of thermal water away from such upflow zones through reservoirs in the Bishop Tuff and early rhyolite accounts for temperature reversals encountered in most existing wells. Dating of hot-spring deposits from active and inactive thermal areas confirms previous interpretations of the evolution of hydrothermal activity that suggest two periods of extensive hot-spring discharge, one peaking about 300 ka and another extending from about 40 ka to the present. The onset of hydrothermal activity around 40 ka coincides with the initiation of rhyolitic volcanism along the Mono-Inyo Craters volcanic chain that extends beneath the caldera's west moat.     

Structure of the Nemrut caldera (Eastern Anatolia, Turkey) and associated hydrothermal fluid circulation

Plio-Quaternary volcanism played an important role in the present physical state of Eastern Anatolia. Mount Nemrut, situated to the west of Lake Van is one of the main volcanic centers in the region, with a spectacular summit caldera 8.5 × 7 km in diameter. The most recent eruptions of the volcano were in 1441, 1597 and 1692. Nemrut Lake covers the western half of the caldera; it is a deep, half-bowl-shaped lake with a maximum depth of 176 m. Numerous eruption centers are exposed within the caldera as a consequence of magma–water interaction. Current activity of Nemrut caldera is revealed as hot springs, fumaroles and a small, hot lake.Self-potential and bathymetric surveys carried out in the caldera were used to characterize the structure of the caldera and the associated hydrothermal fluid circulation. In addition, analyses based on digital elevation models and satellite imagery were used to improve our knowledge about the structure of the caldera. According to SP results, the flanks of the volcano represent “the hydrogeologic zone”, whereas the intra-caldera region is an “active hydrothermal area” where the fluid circulation is controlled by structural discontinuities. There is also a northern fissure zone which exhibits hydrothermal signatures. Nemrut caldera collapsed piecemeal, with three main blocks. Stress controlling the collapse mechanism seems to be highly affected by the regional neotectonic regime. In addition to the historical activity, current hydrothermal and hydrogeologic conditions in the caldera, in which there is a large lake and shallow water table, increase the risk of the quiescent volcano.     

Geochemistry of waters in the Valley of Ten Thousand Smokes region, Alaska

Meteoric waters from cold springs and streams outside of the 1912 eruptive deposits filling the Valley of Ten Thousand Smokes (VTTS) and in the upper parts of the two major rivers draining the 1912 deposits have similar chemical trends. Thermal springs issue in the mid-valley area along a 300-m lateral section of ash-flow tuff, and range in temperature from 21 to 29.8°C in early summer and from 15 to 17°C in mid-summer. Concentrations of major and minor chemical constituents in the thermal waters are nearly identical regardless of temperature. Waters in the downvalley parts of the rivers draining the 1912 deposits are mainly mixtures of cold meteoric waters and thermal waters of which the mid-valley thermal spring waters are representative. The weathering reactions of cold waters with the 1912 deposits appear to have stabilized and add only subordinate amounts of chemical constituents to the rivers relative to those contributed by the thermal waters. Isotopic data indicate that the mid-valley thermal spring waters are meteoric, but data is inconclusive regarding the heat source. The thermal waters could be either from a shallow part of a hydrothermal system beneath the 1912 vent region or from an incompletely cooled, welded tuff lens deep in the 1912 ash-flow sheet of the upper River Lethe area.Bicarbonate-sulfate waters resulting from interaction of near-surface waters and the cooling 1953–1968 southwest Trident plug issue from thermal springs south of Katmai Pass and near Mageik Creek, although the Mageik Creek spring waters are from a well-established, more deeply circulating hydrothermal system. Katmai caldera lake waters are a result of acid gases from vigorous drowned fumaroles dissolving in lake waters composed of snowmelt and precipitation.     

Geochemical investigations of submarine volcanic exhalations to the east of Panarea, Aeolian Islands, Italy

Results are presented on scubadiving investigations carried out on thermal manifestations in the area of Panarea (Aeolian Islands). The area investigated falls inside a caldera which extends from the main island to the group of islets located to the northeast. The distribution of the gaseous manifestations is regulated by the NE-SW, NW-SE and N-S regional tectonic directrices, through which the more recent basic magma intruded, giving rise to dikes and pillow lavas. f_O2-temperature relation of the gases sampled in the investigated area was calculated to be: logf_O2 = 11−24,593/T which indicates that a buffering mechanism acted on the gases as they cooled down during their ascent. The high ³He/⁴He ratio (6 × 10⁻⁶) and the δ¹³C = −3.2%. (PDB), suggest the presence of a magmatic component in the gas feeding the investigated manifestations. The above relations and the almost constant high He/N₂ ratio suggest that all the fumaroles are fed by the same deep hot fluids. On the basis of both the chemical characters of the fluids and the geothermo-barometric data, a deep geothermal body, having a temperature of about 240°C, is recognized. Two other shallower thermal aquifers, with a temperature of 170–210°C, are identified. A circulation pattern of the geothermal fluids is also proposed. On the basis of calculations regarding the convective energy released by the geothermal system of Panarea, and the magmatic mass responsible for the positive gravimetric anomaly of the area, it was estimated that the last volcanic activity took place less then 10,000 years ago.     

Chemical and stable isotopic models for boundary creek warm springs, southwestern Yellowstone National Park, Wyoming

Thermal springs of the Boundary Creek hydrothermal system in the southwestern part of Yellowstone Park outside the caldera boundary vary in chemical and isotopic composition, and temperature. The diversity may be accounted for by a combination of processes including boiling of a deep thermal water, mixing of the deep thermal water with cool meteoric water and/or with condensed steam or steam-heated meteoric water, and chemical reactions with surrounding rocks. Dissolved-silica, Na⁺, K⁺ and Ca²⁺ contents of the thermal springs could result from a thermal fluid with a temperature of 200 ± 20°C. Chloride-enthalpy and silica-enthalpy mixing models suggest mixing of 230°C, 220 mg/l Cl⁻ thermal water with cool, low-Cl⁻ components. A 350 to 390°C component with Cl⁻ ≥ 300 mg/l is possibly present in thermal springs inside the caldera but is not required to fit observed spring chemical and isotopic compositions. Irreversible mass transfer models in which a low-temperature water reacts with volcanic glass as it percolates downward and warms, can account for observed pH and dissolved-silica, K⁺, Na⁺, Ca²⁺ and Mg²⁺ concentrations, but produces insufficient Cl⁻ or F⁻ for measured concentrations in the warm springs. The ratio of a_Na/a_H, and Cl⁻ are best accounted for in mixing models. The water-rock interaction model fits compositions of acid-sulfate waters observed at Summit Lake and of low-Cl⁻ waters involved in mixing.The cold waters collected from southwestern Yellowstone Park have δD values ranging from −118 to −145 per mil and δ¹⁸O values of −15.9 to −19.4 per mil. Two samples from nearby Island Park have δD values of −112 and −114 per mil and δ¹⁸O values of −15.1 and −15.3 per mil. All samples of thermal water plot significantly to the right of the meteoric water line. The low Cl⁻ and variable δD values of the thermal waters indicate isotopic compositions are derived by extensive dilution with cold meteoric water and by steam separation on ascent to the surface. Many of the hot springs with higher δD values may contain in addition a significant amount of high-D, low-Cl⁻, acid-sulfate or steam-heated meteoric water. Mixing models, Cl⁻ content and isotopic compositions of thermal springs suggest that 30% or less of a deep thermal component is present. For example, the highest-temperature springs from Three Rivers, Silver Scarf and Upper Boundary Creek thermal areas contain up to 70% cool meteoric water and 30% hot water components, springs at Summit Lake and Middle Boundary Creek spring 57 are acid-sulfate or steam-heated meteoric water; springs 27 and 48 from Middle Boundary Creek and 49 from Mountain Ash contain in excess of 50% acid-sulfate water; and Three Rivers spring 46 and Phillips could result from mixing hot water with 55% cool meteoric water followed by mixing of acid-sulfate water. Extensive dilution by cool meteoric water increases the uncertainties in quantity and nature of the deep meteoric, thermal component.     

Gas geochemistry of the Valles caldera region, New Mexico and comparisons with gases at Yellowstone, Long Valley and other geothermal systems

Noncondensible gases from hot springs, fumaroles, and deep wells within the Valles caldera geothermal system (210–300°C) consist of roughly 98.5 mol% CO₂, 0.5 mol% H₂S, and 1 mol% other components. ³He/⁴He ratios indicate a deep magmatic source (R/R_a up to 6) whereas δ¹³C–CO₂ values (−3 to −5‰) do not discriminate between a mantle/magmatic source and a source from subjacent, hydrothermally altered Paleozoic carbonate rocks. Regional gases from sites within a 50-km radius beyond Valles caldera are relatively enriched in CO₂ and He, but depleted in H₂S compared to Valles gases. Regional gases have R/R_a values ≤1.2 due to more interaction with the crust and/or less contribution from the mantle. Carbon sources for regional CO₂ are varied. During 1982–1998, repeat analyses of gases from intracaldera sites at Sulphur Springs showed relatively constant CH₄, H₂, and H₂S contents. The only exception was gas from Footbath Spring (1987–1993), which experienced increases in these three components during drilling and testing of scientific wells VC-2a and VC-2b. Present-day Valles gases contain substantially less N₂ than fluid inclusion gases trapped in deep, early-stage, post-caldera vein minerals. This suggests that the long-lived Valles hydrothermal system (ca. 1 Myr) has depleted subsurface Paleozoic sedimentary rocks of nitrogen. When compared with gases from many other geothermal systems, Valles caldera gases are relatively enriched in He but depleted in CH₄, N₂ and Ar. In this respect, Valles gases resemble end-member hydrothermal and magmatic gases discharged at hot spots (Galapagos, Kilauea, and Yellowstone).     

Fluid inclusion evidence for rapid formation of the vapor-dominated zone at Sulphur Springs, Valles caldera, New Mexico, USA

Microthermometric measurements were obtained for 618 fluid inclusions in hydrothermal quartz, fluorite and calcite and magmatic quartz phenocrysts in intracaldera tuffs from the VC-2A core hole in order to study evolutionary processes of the Sulphur Springs hydrothermal system in the Valles caldera. Relatively high T_h values in samples from shallow depths indicate erosion of about 200 m of caldera fill since deposition of hydrothermal minerals at shallow depths in the Sulphur Springs hydrothermal system, accompanied by a descent in the water table of the liquid-dominated reservoir. For samples collected below the current water level of the well, the minimum values of homogenization temperature (T_h) fit the present thermal profile, whereas minimum T_h values of samples from above the water level are several tens of degrees higher than the present thermal profile and fit a paleo-thermal profile following the boiling point curve for pure water, as adjusted to 92 °C at 20 m below the present land surface. This is attributed to development of an evolving vapor zone that formed subsequent to a sudden drop in the water table of the liquid-dominated reservoir. We suggest that these events were caused by the drainage of an intracaldera lake when the southwestern wall of the caldera was breached about 0.5 Ma. This model indicates that vapor zones above major liquid-dominated geothermal reservoirs can be formed due to dramatic changes in geohydrology and not just from simple boiling.     

The hydrothermal system of Nevado del Ruiz volcano,Colombia

Hot springs and steam vents on the slopes of Nevado del Ruiz volcano provide evidence regarding the nature of hydrothermal activity within the summit and flanks of the volcano. At elevations below 3000 m, alkali-chloride water is discharged from two groups of boiling springs and several isolated warm springs on the western slope of Nevado del Ruiz. Chemical and isotopic geothermometers suggest that the boiling springs are fed by an aquifer having a subsurface equilibration temperature of at least 175°C, and the sampled warm spring is fed by an aquifer having a subsurface equilibration temperature near 150°C. Similarities in conservative solute ratios (e.g., B/Cl) indicate that the alkali-chloride waters may be related to a single reservoir at depth. Isotopic ratios of hydrogen and oxygen indicate that recharge for the alkali-chloride aquifers comes mostly from higher elevations on the volcano. Steam vents and steam-heated bicarbonate-sulfate springs at higher elevations, along a linear structural trend with the alkali-chloride springs, may be derived partly from the alkali-chloride water at depth by boiling. Steam from the vents (84°C) yields a gas geothermometer temperature of 209°C. Acid-sulfate-chloride and acid-sulfate waters are discharged widely from warm springs above 3000 m on the northern and eastern slopes of Nevado del Ruiz. Similarities in B/Cl and SO₄/Cl ratios suggest that the acid waters are mixtures of water from an acid-sulfate-chloride reservoir with various proportions of shallow, dilute groundwater. The major source of sulfate, halogens, and acidity for the acid waters may be high-temperature magmatic gases. Available data on hot spring temperatures and compositions indicate that they have remained fairly stable since 1968. However, the eruption of November 13, 1985 apparently caused an increase in sulfate concentration in some of the acid springs that peaked about a year after the eruption. Long-term monitoring of hot spring compositions over many years will be required to better define the effects of volcanic activity on the Nevado del Ruiz hydrothermal system.     

Helium isotopic ratio in Vulcano island fumaroles: temporal variations in shallow level mixing and deep magmatic supply

Intensive gas emanations occur throughout the island of Vulcano, Italy. Sharp fluctuations recorded in the crater gas composition suggest the presence of two separate volcanic reservoirs and continuous mixing with another source, “crustal” waters. This mixing differs between the beach and crater fumaroles. Gas samples from three crater fumaroles with temperatures ranging from 200 to 550 ° C were sampled repeatedly over a one year period. During the same interval of time, six samples from submarine and subaerial beach fumaroles and water well gases were also sampled. Gases from one crater fumarole (F5) showed variations of (³He/⁴He)_fumarole to (³He/⁴He)_air between 5 and 6 correlated with variations of several chemical species. High ³He/⁴He ratios for the beach fluids, similar to those of crater fluids, suggest the existence of a unique large magmatic reservoir at depth feeding both the crater and beach intermediate reservoirs. However, temporal changes clearly indicate variable degrees of fluids mixing, and the geographic distribution of the ³He/⁴He ratios as well as the chemical composition of the fluids suggest the existence between the magma reservoir and the surface of two intermediate different reservoirs, independently related to crater and to beach fumaroles.     

Emplacement temperatures of the November 22, 1994 nuée ardente deposits, Merapi Volcano, Java

A study of emplacement temperatures was carried out for the largest of the 22 November 1994 nuée ardente deposits at Merapi Volcano, based mainly on the response of plastic and woody materials subjected to the hot pyroclastic current and the deposits, and to some extent on eyewitness observations. The study emphasizes the Turgo–Kaliurang area in the distal part of the area affected by the nuée ardente, where nearly 100 casualties occurred. The term nuée ardente as used here includes channeled block-and-ash flows, and associated ash-clouds of surge and fallout origins. The emplacement temperature of the 8 m thick channeled block-and-ash deposit was relatively high, 550°C, based mainly on eyewitness reports of visual thermal radiance. Emplacement temperatures for ash-cloud deposits a few cm thick were deduced from polymer objects collected at Turgo and Kaliurang. Most polymers do not display a sharp melting range, but polyethylene terephthalate used in water bottles melts between 245 and 265°C, and parts of the bottles that had been deformed during fabrication molding turn a milky color at 200°C. The experimental evidence suggests that deposits in the Turgo area briefly achieved a maximum temperature near 300°C, whereas those near Kaliurang were <200°C. Maximum ash deposit temperatures occurred in fallout with a local source in the channeled block-and-ash flow of the Boyong river valley; the surge deposit was cooler (180°C) due to entrainment of cool air and soils, and tree singe-zone temperatures were around 100°C.