SeaMARC II study of a giant submarine slump on the northern Chile continental slope

Abstract

A giant submarine slump, encompassing a 91‐km by 26‐km block, occurring on the continental slope offshore Iquique, Chile, was identified during a SeaMARC II survey. Utilizing SeaMARC II side‐scan imagery, bathymetry, and seismic reflection data, five morphostructural zones of the slump were identified: the fissured zone, scar zone, tensional depression, central block, and front zone. The fissured zone was developed on the crown of the slump; the scar zone is characterized by scars with the crescent‐shaped slip surfaces and throws ranging from 200 m to 50 m. The tensional depression zone is marked by an area voided by mass slumping, while the central block morphology was formed by uplift. The front zone is comprised of both compressional and tensional subzones. The compressional subzone is characterized by a relative topographic low, on the middle slope, whereas the extensional subzone is characterized by a convex pattern of alternated ridges and hollows, which may represent the debris of the slump on the lower slope. The formation of the slump was strongly influenced by the subduction of the Nazca plate beneath the Chile continental margin, which resulted in the subsidence of the continental slope with a resultant increase in the slope gradient and pore‐water pressure in the sedimentary layers. Slump formation was further facilitated by the development of a complex fault system associated with the subduction and by the triggering effect of earthquakes in the area.     

Continental slope sedimentation adjacent to an ice margin I. Seismic facies of Labrador Slope

Sleeve-gun, 3.5-kHz, and 12-kHz profiles from the Labrador Slope provide the basis for an analysis of sedimentary facies, processes, and evolution of a continental slope adjacent to an ice margin. The upper slope is deeply incised by numerous canyons reflecting headward canyon branching. The less rugged middle-slope topography has fewer canyons and large slide and slump scars followed downslope by debris-flow deposits. Echo character of seismic profiles reflects the difference in sediment types supplied from mud-dominated sources and sand-, gravel- and till-dominated sources. On the rise, debris-flow deposits are largely confined to canyons. Intercanyon areas are dominated by spill-over turbidites alternating with hemipelagic sediments, which on some of the southern to southwestern levees occur in sediment-wave fields formerly attributed to bottom-current activity.     

Sediment transport in Washington and Norfolk submarine canyons

A sediment study suggests that Washington and Norfolk canyons off the Mid-Atlantic States are not inactive, but have served periodically since the Late Pleistocene as conduits of sediment originating on the adjacent shelf and upper slope. Large quantities of sand occur in the canyon heads as thin beds and laminae, and on the continental slope as mixtures of sand (to $\text{>40\%}$), silt and clay that are extensively reworked by burrowing organisms. Sandy turbidites occur in the canyons on the rise. Basinward dispersal, from the outer shelf and uppermost slope, is recorded by heavy mineral suites and bioclastic components, primarily foraminifera of shallow marine origin, in the lower slope and upper continental rise canyon cores. The down-axis movement of material, presumably episodic, in the Holocene to recent results from offshelf spillover into canyon heads, failure on the steep walls bordering canyons on the slope, and resuspension by bottom currents.     

Submarine canyons on the north of Chiwei Island:influenced by recent extension of the southern Okinawa Trough

Based on new multibeam bathymetric data and about 300 km long single seismic profiles, three topographic units were identified： the canyons, fractural valley and submarine terrace on the north of Chiwei Island where is a structural transition zone between the southern trough and the middle trough. The Chiwei Canyon and the North Chiwei Canyon are two of the largest canyons in the East China Sea （ECS） slope. Topographic features and architectures of them are described. The study shows that both of them are originated along faults. The evolution and spatial distribution of topographic units in the study area are controlled mainly by three groups of faults which were formed and reactive in the recent extensional phase of Okinawa Trough. The Chiwei Canyon was initia- ted during the middle Pleistocene and guided by F4 that is a N--S trending fault on the slope and F1, a large NW--SE trending fault on the trough. The pathway migration from the remnant channel to the present one of Chiwei Canyon is the result of uplift of tilted fault block that is coupled to the recent extension movements of the southern trough. The submarine terrace is detached from the ECS slope by the NEE -trending fault. The North Chiwei Canyon, developing during the late Pleistocene, is guided by FS, a N-S trending fault, diverted and blocked by the submarine terrace.     

Submarine canyons on the north of Chiwei Island: influenced by recent extension of the southern Okinawa Trough

Based on new multibeam bathymetric data and about 300 km long single seismic profiles, three topographic units were identified:the canyons, fractural valley and submarine terrace on the north of Chiwei Island where is a structural transition zone between the southern trough and the middle trough. The Chiwei Canyon and the North Chiwei Canyon are two of the largest canyons in the East China Sea (ECS) slope. Topographic features and architectures of them are described. The study shows that both of them are originated along faults. The evolution and spatial distribution of topographic units in the study area are controlled mainly by three groups of faults which were formed and reactive in the recent extensional phase of Okinawa Trough. The Chiwei Canyon was initiated during the middle Pleistocene and guided by F4 that is a N-S trending fault on the slope and F1, a large NW-SE trending fault on the trough. The pathway migration from the remnant channel to the present one of Chiwei Canyon is the result of uplift of tilted fault block that is coupled to the recent extension movements of the southern trough. The submarine terrace is detached from the ECS slope by the NEE-trending fault. The North Chiwei Canyon, developing during the late Pleistocene, is guided by F5, a N-S trending fault, diverted and blocked by the submarine terrace.     

莱州湾西构造带断裂特征及其对油气成藏的控制

受古近纪莱州湾凹陷大规模断陷、郯庐断裂右旋走滑和垦东凸起大规模隆升三方面因素共同作用,莱州湾西构造带断裂系统发育,根据断裂性质及发育规模将断裂划分为3组不同方向的断裂组合,对油气的运移、聚集及保存都产生重要影响。根据莱州湾地区油气成藏规律并结合渤海其他区域近年勘探成果综合分析,莱北1号断层、斜坡区东西向反向正断层和走滑末端雁行式断层三类大规模调节断层对于油气成藏影响作用较大,这三类断层所控制的圈闭也是莱州湾凹陷及围区下一步勘探获得突破的重点区域。     

Late Cretaceous-Paleocene extension on the Vøring Volcanic Margin

High-quality seismic data document a Maastrichtian-Paleocene rift episode on the Vøring margin lasting for 20 m.y. prior to continental breakup. The rift structures are well imaged in the Fenris Graben and Gjallar Ridge region in the western Vøring Basin, and are characterized by low-angle detachment faults with variable fault geometries from south to north. The structural restoration has facilitated the division of pre- and syn-rift sediments across the extensional terrain, which is subsequently used to evaluate mode and mechanism for the lithospheric deformation. Extension estimates based on the structural restoration, subsidence analysis and crustal thickness evaluations yield stretching factors ranging between 1.5 to 2.3 across the main fault zone just landward of the early Tertiary flood basalts. The structural restoration also shows that a middle crustal dome structure, observed beneath the low-angle faults, can be explained by extensional unroofing. Thus, the dome structure may represent a possible metamorphic core complex. Calculations of the effects on vertical motion, assuming uniform and two-layer differential stretching models combined with the arrival of the Iceland mantle plume during rifting, indicate that the uniform extension model may account for both observed early rift subsidence and subsequent late rift uplift and erosion. Although the differential model can not be excluded, it implies early rift uplift which is not compatible with our seismic interpretation. The direct and indirect effects of the Iceland mantle plume may have caused as much as 1.2 km of late rift uplift. Comparison of the volcanic Vøring margin and the non-volcanic West Iberian margin shows similarities in terms of structural style as well as in mode and distribution of extension.     

The continental slope off New England: A long-range sidescan-sonar perspective

The first continuous overview of a large segment of the continental slope and rise off the northeastern United States has been obtained using the GLORIA II long-range sidescan-sonar system. Extensive dissection by canyon and gully systems and evidence of possible large-scale sediment sliding are seen on the slope. The style and degree of incision, as well as the numbers and locations of canyons, have been found to differ significantly from previously published maps. It is suggested that the slope is a significant source of the sediment that has been deposited on the rise, and that some abrupt changes in the courses of canyons may be the result of local structural control.     

Geomorphological evidence for upslope canyon-forming processes on the northern KwaZulu-Natal shelf,SW Indian Ocean,South Africa

A geomorphological and statistical analysis of slope canyons from the northern KwaZulu-Natal continental margin is documented and compared with submarine canyons from the Atlantic margin of the USA. The northern KwaZulu-Natal margin is characterized by increasing upslope relief, concave slope-gradient profiles and features related to upslope growth of the canyon forms. Discounting slope-gradient profile, this morphology is strikingly similar to canyon systems of the New Jersey slope. Several phases of canyon incision indicate that downslope erosion is also an important factor in the evolution of the northern KwaZulu-Natal canyon systems. Despite the strong similarities between the northern KwaZulu-Natal and New Jersey slope-canyon systems, key differences are evident: (1) the concavity of the northern KwaZulu-Natal slope, contrasting with the ∼linear New Jersey slope; (2) the relative isolation of the northern KwaZulu-Natal canyons, rather than the dense clustering of the New Jersey canyons; and (3) the absence of strongly shelf-breaching canyons along the northern KwaZulu-Natal margin. In comparison with the New Jersey margin, we surmise a more youthful stage of canyon evolution, a result of either the canyons themselves being younger or the formative processes being less active. Less complicated patterns of erosion resulting from reduced sediment availability have developed in northern KwaZulu-Natal. The reduction in slope concavity on the New Jersey margin may be the result of grading of the upper slope by intensive headward erosion, a process more subdued—or less evident—on the KwaZulu-Natal margin.     

Analysis of submarine slumping in the continental slope off the southern coast of Israel

Abstract

The continental slope off the coast of Israel is riddled with numerous large slump scars at depths greater than 400 m. Recent scar slumps are situated in the steepest central portions of the continental slope (400–450 m depth, α=6°), frequently disfiguring older slump scars in its lower portions. The slumping materials were probably largely transported downslope in the form of density currents, and occasionally by sliding of large sediment chunks. Upslope retrogressive slumping phases progressively disfigure the shape of the slump scars until they totally disappear, causing net reduction of the thickness of the sedimentary column. To provide a basis for the quantitative analysis of slumping, laboratory vane tests, triaxial consolidated, undrained compression tests with pore‐pressure measurements, drained direct shear tests, and consolidation tests were performed oh undisturbed samples. Because the sediments consist of normally consolidated silty clays, the geotechnical properties measured on the core samples can be readily extrapolated for greater depths, assuming the sediments are homogeneous. Angles of internal friction measured by direct shearing under drained conditions are ?_d =24°‐25°, designating the maximum possible angle of a stable infinite slope. These angles are appreciably higher than the steepest slopes in the investigated area, and a drained slumping mechanism is therefore considered unlikely. The slopes of the slump scar walls are about 20°; therefore, in the absence of active erosional, sedimentological, or tectonic agents, these walls have long‐term stability (drained shear). Undrained shear failure resulting in slope instability may be attributable to rapid changes in slope geometry (undercutting or oversteepening of the slope), fluctuations in pore pressure, or accelerations associated with earthquakes. Undrained shear‐strength parameters were determined by both laboratory consolidated‐un‐drained triaxial tests and by miniature vane shear tests. The angles of internal friction that were measured are ?_cu =15°‐17°, and the c_u/p_o values range between 0.22 and 0.75. An analysis of the force equilibrium within the sediments leads to the conclusion that horizontal earthquake‐induced accelerations, as little as 5–6% of gravity, are sufficient to cause slope failure in the steepest slope zone (400–450 m depth, α = 6°, c_u /p_o =0.25). Collapse resulting from liquefaction is unlikely, as the sediments are normally consolidated silty clays with intermediate sensitivity, S_t =2–4.

The existence of slump scars in the lower portion of the continental slope, characterized by gentle slopes (α=1°‐3°) and sediments with high shear strength (c _u /p _o=0.30–0.50) is attributed to large horizontal accelerations(k=12–16% of gravity). Owing to the wide range of geotechnical properties of the sediments (c_u /p_o = 0.20–0.75) and the inclination of the continental slope (α=1°‐6°), the same earthquake may generate a wide range of horizontal accelerations in different portions of the continental slope, and slumping may occur wherever the stability equilibrium is disrupted.     

Analysis of submarine slumping in the continental slope off the southern coast of Israel

Abstract

The continental slope off the coast of Israel is riddled with numerous large slump scars at depths greater than 400 m. Recent scar slumps are situated in the steepest central portions of the continental slope (400–450 m depth, α = 6°), frequently disfiguring older slump scars in its lower portions. The slumping materials were probably largely transported downslope in the form of density currents, and occasionally by sliding of large sediment chunks. Upslope retrogressive slumping phases progressively disfigure the shape of the slump scars until they totally disappear, causing net reduction of the thickness of the sedimentary column. To provide a basis for the quantitative analysis of slumping, laboratory vane tests, triaxial consolidated, undrained compression tests with pore‐pressure measurements, drained direct shear tests, and consolidation tests were performed oh undisturbed samples. Because the sediments consist of normally consolidated silty clays, the geotechnical properties measured on the core samples can be readily extrapolated for greater depths, assuming the sediments are homogeneous. Angles of internal friction measured by direct shearing under drained conditions are ?_d =24°‐25°, designating the maximum possible angle of a stable infinite slope. These angles are appreciably higher than the steepest slopes in the investigated area, and a drained slumping mechanism is therefore considered unlikely. The slopes of the slump scar walls are about 20°; therefore, in the absence of active erosional, sedimentological, or tectonic agents, these walls have long‐term stability (drained shear). Undrained shear failure resulting in slope instability may be attributable to rapid changes in slope geometry (undercutting or oversteepening of the slope), fluctuations in pore pressure, or accelerations associated with earthquakes. Undrained shear‐strength parameters were determined by both laboratory consolidated‐un‐ drained triaxial tests and by miniature vane shear tests. The angles of internal friction that were measured are ?_cu =15°‐17°, and the c_u/p _o values range between 0.22 and 0.75. An analysis of the force equilibrium within the sediments leads to the conclusion that horizontal earthquake‐induced accelerations, as little as 5–6% of gravity, are sufficient to cause slope failure in the steepest slope zone (400–450 m depth, α=6°, c_u/p _o=0.25). Collapse resulting from liquefaction is unlikely, as the sediments are normally consolidated silty clays with intermediate sensitivity, S_t =2–4.

The existence of slump scars in the lower portion of the continental slope, characterized by gentle slopes (α=1°‐3°) and sediments with high shear strength (c_u/p _o=0.30–0.50) is attributed to large horizontal accelerations (k= 12–16% of gravity). Owing to the wide range of geotechnical properties of the sediments (c_u/p _o= 0.20–0.75) and the inclination of the continental slope (α=1°‐6°), the same earthquake may generate a wide range of horizontal accelerations in different portions of the continental slope, and slumping may occur wherever the stability equilibrium is disrupted.     

Slope-confined submarine canyons in the Baiyun deep-water area,northern South China Sea: variation in their modern morphology

On the basis of newly collected multibeam bathymetric data, chirp profiles and existing seismic data, we presented a detailed morphological interpretation of a series of slope-confined canyons in water depths of 300–2000 m in the Baiyun deep-water area, northern margin of the South China Sea. Although these canyons are commonly characterized by regular spacing and a straight-line shape, they vary in their lengths, starting and ending water depths, canyon relief, slope gradients, wall slope gradients and depth profiles along the axis. The eastern canyons (C1–C8) have complex surface features, low values in their slope gradient, canyon relief and wall slope gradient and high values in their length and starting and ending depth contrasting to the western ones (C9–C17). From the bathymetric data and chirp profiles, we interpret two main processes that have controlled the morphology and evolution of the canyons: axial incision and landsliding. The western part of the shelf margin where there were at least four stages of submerged reefs differs from the eastern part of the shelf margin where sedimentary undulations occurred at a water depth of ~650 m. We consider that the variation in morphology of submarine canyons in the study area is the result of multiple causes, with the leading cause being the difference in stability of the upper slope which is related to the submerged reefs and sedimentary undulations.     

Submarine canyon development in the Izu-Bonin forearc: A SeaMARC II and seismic survey of Aoga Shima Canyon

SeaMARC II sidescan (imagery and bathymetry) and seismic data reveal the morphology, sedimentary processes, and structural controls on submarine canyon development in the central Izu-Bonin forearc, south of Japan. Canyons extend up to 150 km across the forearc from the trench-slope break to the active volcanic arc. The canyons are most deeply incised (1200–1700 m) into the gentle gradients (1–2°) upslope on the outer arc high (OAH) and lose bathymetric expression on the steep (6–18°) inner trench-slope. The drainage patterns indicate that canyons are formed by both headward erosion and downcutting. Headward erosion proceeds on two scales. Initially, pervasive small-scale mass wasting creates curvilinear channels and pinnate drainage patterns. Large-scale slumping, evidenced by abundant crescent-shaped scarps along the walls and tributaries of Aoga Shima Canyon, occurs only after a channel is present, and provides a mechanism for canyon branching. The largest slump has removed >16 km³ of sediment from an 85 km² area of seafloor bounded by scarps more than 200 m high and may be in the initial stages of forming a new canyon branch. The northern branch of Aoga Shima Canyon has eroded upslope to the flanks of the arc volcanoes allowing direct tapping of this volcaniclastic sediment source. Headward erosion of the southern branch is not as advanced but the canyon may capture sediments supplied by unconfined (non-channelized) mass flows.Oligocene forearc sedimentary processes were dominated by unconfined mass flows that created sub-parallel and continuous sedimentary sequences. Pervasive channel cut-and-fill is limited to the Neogene forearc sedimentary sequences which are characterized by migrating and unconformable seismic sequences. Extensive canyon formation permitting sediment bypassing of the forearc by canyon-confined mass flows began in the early Miocene after the basin was filled to the spill points of the OAH. Structural lows in the OAH determined the initial locus of canyon formation, and outcropping basement rocks have prevented canyon incision on the lower slope. A major jog in the canyon axis, linear tributaries, and a prominent sidescan lineament all trend NW-NNW, reflecting OAH basement influence on canyon morphology. This erosional fabric may reflect joint/fracture patterns in the sedimentary strata that follow the basement trends. Once the canyons have eroded down to more erosion-resistant levels, channel downcutting slows relative to lateral erosion of the canyon walls. This accounts for the change from a narrow canyon axis in the thickly sedimented forearc basin to a wider, more rugged canyon morphology near the OAH. About 9500 km³ of sediment has been eroded from the central, 200 km long, segment of the Izu-Bonin forearc by the formation of Aoga Shima, Myojin Sho and Sumisu Jima canyons. The volume of sediment presently residing in the adjacent trench, accretionary wedge, and lower slope terrace basin accounts for <25% of that eroded from the canyons alone. This implies that a large volume (>3500 km³ per 100 km of trench, ignoring sediments input via forearc bypassing) has been subducted beneath the toe of the trench slope and the small accretionary prism. Unless this sediment has been underplated beneath the forearc, it has recycled arc material into the mantle, possibly influencing the composition of arc volcanism.     

Morphological characteristics in the area off eastern Taiwan Island and their tectonic implications

On the basis of bathymetric data and other geological and geophysical data obtained during the first survey conducted by Chinese Mainland in the area off eastern Taiwan Island from May to June in 2000, the morphological features of the region, the tectonic control to the seafloor topography and their tectonic implication are studied and discussed. The results have revealed that both the slope zone of the Ryukyu arc and the Ryukyu Trench present a typical morphotectonic characteristics controlled by the trench-arc system in the West Pacific Ocean. At the slope of eastern Taiwan Island the isobathic lines parallel to the coastline and distribute densely in nearly N-S direction and the slope gradient of topography is large. Such a unique feature is attributed to the collision of the Luzon arc and Eurasia continent. In the Huatung Basin, turbidity fans and submarine canyons are well developed, the formations of which are mainly related to the steep topography of the slope of the Luzon arc and the abundant s     

Carbonate slope morphology revealing sediment transfer from bank-to-slope (Little Bahama Bank,Bahamas)

New high-quality multibeam and high-resolution seismic data reveal new observations on sediment transfer and distribution and margin morphometrics in the uppermost slope of Northeastern Little Bahama Bank between 20 and 300 m water depth. The echofacies/backscatter facies show an alongslope sediment distribution forming successive strips. The upper part of the uppermost slope corresponds to the alternation of several submerged coral terraces and escarpments that could be related to Late Quaternary sea-level variations. The terraces could either be related to periods of stagnating sea-level or slow-down in sea-level change and therefore increased erosion by waves, or periods of accelerated sea-level rise since the Last Glacial Maximum. Terraces could therefore be related to coral construction and drowing. The medium part corresponds to the marginal escarpment, a steep cemented area. The lower part of the uppermost slope shows a discontinuous Holocene sediment wedge with varying thickness between 0 and 35 m. It is separated from the upper part by a zone of well-cemented seafloor associated with the marginal escarpment. Passing cold fronts result in sediment export caused by density cascading. The associated sediment fall-out and convective sedimentation can generate density currents that form this wedge and eventually flow through linear structures on the upper slope. The survey reveals the presence of recently active channels that extend over the entire uppermost slope and interrupt the wedge. The channels connect shallow tidal channels to submarine valleys connected to the proximal part of canyons. They directly feed the canyons with platform-derived sediment forming low-density turbidity currents and could supply the deepest part of the system with coarse-grained sediment directly exported from the carbonate platform.     

First results from the North Iceland experiment

Between June 2004 and September 2004 a temporary seismic network was installed on the northern insular shelf of Iceland and onshore in north Iceland. The seismic setup aimed at resolving the subsurface structure and, thus, the geodynamical transition from Icelandic crust to typical oceanic crust along Kolbeinsey Ridge. The experiment recorded about 1,000 earthquakes. The region encloses the Tjörnes Fracture Zone containing the Husavik–Flatey strike-slip fault and the extensional seismic Grimsey Lineament. Most of the seismicity occurs in swarms offshore. Preliminary results reveal typical mid-ocean crust north of Grimsey and a heterogeneous structure with major velocity anomalies along the seismic lineaments and north–south trending subsurface features. Complementary bathymetric mapping highlight numerous extrusion features along the Grimsey Lineament and Kolbeinsey Ridge. The seismic dataset promises to deliver new insights into the tectonic framework for earthquakes in an extensional transform zone along the global mid-ocean ridge system.     

Modes of development of slope canyons and their relation to channel and levee features on the Ebro sediment apron, off-shore northeastern Spain

Six submarine slope canyons in an area of the northwestern Mediterranean, offshore from the Ebro River and Delta, were surveyed with bathymetric swathmapping (SeaBeam) and mid-range side-looking sonar (SeaMARC I). All of the canyons have slightly winding paths with concave-upwards gradients that are relatively steep shallower than 1,200 m. Two major types of canyons are identified on the basis of their morphologic character at the base of the slope; Type-I canyons lead to an unchannelled base-of-slope deposit and Type-II canyons are continuous with channel-levee systems that cross the rise.Four Type-I canyons were surveyed in the area. Two of these are broad, U-shaped, steep (average gradients of 1:14), do not indent the shelf, and terminate downslope at debris-flow deposits. These two canyons, the most northern in the area, have rounded heads with extensive gullies separated by knife-edge ridges. Relief of the canyon walls is about equal on both sides of the canyons, although the right-hand walls (looking downslope) are generally steeper. The other two Type-I canyons in the area are similar in that they do not indent the shelf, but they are much smaller and shallower and coalesce before terminating in the base-of-slope region. The two Type-II canyons that feed leveed-channels are U-shaped with flatter floors, longer profiles and gentler gradients than Type-I canyons. They are closer to the Valencia Valley and have relatively small cross-sectional areas.We propose a four-stage evolutionary sequence to explain the development of the canyons observed in this section on the prograding Ebro margin. During the initial stage, slumping and erosion on the slope creates a network of small gullies. During the next stage, headward growth of one (or more) gully leads to a major indentation of the shelf. This is the critical factor for developing a channel that will incise the slope and provide a major conduit for moving sediment to the basin. Stage 3 is characterized by the development of a continuous channel accompanied by levee growth across the lobe. In the final stage, the channel-levee system becomes inactive either through destruction by mass wasting, infilling of the channel, or loss of the major sediment source.     

The Queen Charlotte Fault, British Columbia: seafloor anatomy of a transform fault and its influence on sediment processes

The Queen Charlotte Fault Zone (QCFZ) off western Canada is the northern equivalent to the San Andreas Fault Zone, the Pacific–North American plate boundary. Geomorphologic expression and surface processes associated with the QCFZ system have been revealed in unprecedented detail by recent seabed mapping surveys. Convergence of the Pacific and North American plates along northern British Columbia is well known, but how the QCFZ accommodates this convergence is still a subject of controversy. The multibeam sonar bathymetry data reveal, for the first time, evidence of a fault valley with small depressions on the upper slope, offshore central Haida Gwaii (Queen Charlotte Islands). The depressions form where strike-slip right-step offsets have realigned the fault due to oblique convergence. Core stratigraphy and radiocarbon dating of sediments within the fault valley and small depressions suggest that these features are recent in origin. In addition, the development of the fault valley and dislocation of submarine canyons control sediment migration from the continental shelf through to the lower slope. This interpretation of the geomorphic expression of major plate tectonic processes along the QCFZ can now be tested with new surveys subsequent to the October 2012 magnitude 7.7 earthquake.     

Recent structures in the Alboran Ridge and Yusuf fault zones based on swath bathymetry and sub-bottom profiling: evidence of active tectonics

The seafloor of the Alboran Sea in the western Mediterranean is disrupted by deformations resulting from convergence between the African and Eurasian plates. Based on a compilation of existing and new multibeam bathymetry data and high-resolution seismic profiles, our main objective was to characterize the most recent structures in the central sector, which depicts an abrupt morphology and was chosen to investigate how active tectonic processes are shaping the seafloor. The Alboran Ridge is the most prominent feature in the Alboran Sea (>130 km in length), and a key element in the Gibraltar Arc System. Recent uplift and deformation in this ridge have been caused by sub-vertical, strike-slip and reverse faults with associated folding in the most recent sediments, their trend shifting progressively from SW–NE to WNW–ESE towards the Yusuf Lineament. Present-day transtensive deformation induces faulting and subsidence in the Yusuf pull-apart basin. The Alboran Ridge and Yusuf fault zones are connected, and both constitute a wide zone of deformation reaching tens of kilometres in width and showing a complex geometry, including different active fault segments and in-relay folds. These findings demonstrate that Recent deformation is more heterogeneously distributed than commonly considered. A narrow SSW–NNE zone with folding and reverse faulting cuts across the western end of the Alboran Ridge and concentrates most of the upper crustal seismicity in the region. This zone of deformation defines a seismogenic, left-lateral fault zone connected to the south with the Al Hoceima seismic swarm, and representing a potential seismic hazard. Newly detected buried and active submarine slides along the Alboran Ridge and the Yusuf Lineament are clear signs of submarine slope instability in this seismically active region.