South Australian earthquakes, 1980–92

The seismicity of South Australia over the period 1980–92 is presented as a follow‐up to earlier studies. The South Australian seismic network has undergone a significant expansion in the last decade, and with it an increase in the number and precision of located earthquakes. The distribution of recent seismic activity is similar to the historical pattern of earthquakes and the previous instrumental seismicity maps, all of which show the three main areas as being the Flinders‐Mt Lofty Ranges, Eyre Peninsula, and the southeast. The one notable exception in the recent study is the presence of earthquake activity in the Musgrave Block, a previously aseismic region. Intensity characteristics are reported for earthquakes that were sufficiently widely felt. Fault plane solutions for three Flinders Ranges earthquakes (previously unpublished) are also presented; the focal mechanisms are consistent with predominant northeast‐southwest compression. The seismic moment method was used to estimate the seismic risk for the major population centres in terms of probability of exceedance of seismic intensity within a given period. These estimates are based on the recurrence parameters and intensity attenuation function for the region. The results place Adelaide close to the AS2121 ‐ 1979 Earthquake Code Zone I/Zone 2 boundary.     

The comparison of the NDSHA, PSHA seismic hazard maps and real seismicity for the Italian territory

Rigorous and objective testing of seismic hazard assessments against the real seismic activity must become the necessary precondition for any responsible seismic risk estimation. Because seismic hazard maps seek to predict the shaking that would actually occur, the reference hazard maps for the Italian seismic code, obtained by probabilistic seismic hazard assessment (PSHA), and the alternative ground shaking maps based on the neo-deterministic approach (NDSHA), are cross-compared and tested against the real seismicity for the territory of Italy. The comparison between predicted intensities and those reported for past earthquakes shows that models generally provide rather conservative estimates, except for PGA with 10 % probability of being exceeded in 50 years, which underestimates the largest earthquakes. In terms of efficiency in predicting ground shaking, measured accounting for the rate of underestimated events and for the territorial extent of areas characterized by high seismic hazard, the NDSHA maps appear to outscore the PSHA ones.     

Assessment of seismic hazard and liquefaction potential of Gujarat based on probabilistic approaches

Gujarat is one of the fastest-growing states of India with high industrial activities coming up in major cities of the state. It is indispensable to analyse seismic hazard as the region is considered to be most seismically active in stable continental region of India. The Bhuj earthquake of 2001 has caused extensive damage in terms of causality and economic loss. In the present study, the seismic hazard of Gujarat evaluated using a probabilistic approach with the use of logic tree framework that minimizes the uncertainties in hazard assessment. The peak horizontal acceleration (PHA) and spectral acceleration (Sa) values were evaluated for 10 and 2?% probability of exceedance in 50?years. Two important geotechnical effects of earthquakes, site amplification and liquefaction, are also evaluated, considering site characterization based on site classes. The liquefaction return period for the entire state of Gujarat is evaluated using a performance-based approach. The maps of PHA and PGA values prepared in this study are very useful for seismic hazard mitigation of the region in future.     

A Study of Seismicity and Earthquake Hazard at the Proposed Kalabsha Dam Site,Aswan, Egypt

High and Aswan Dams Authority (HADA) proposed a plan aiming at constructing a rockfill dam in the Kalabsha area, about 60 km south of Aswan High Dam. The aim of this dam is to restrain the overflow of water to the Kalabsha Valley for keeping one billion cubic meters from being lost due to seepage and evaporation. The safety of dams during earthquakes is extremely important because failure of such a structure may have disastrous consequences on life and property. Therefore, different factors were considered as part of a site assessment. Five seismic source zones, close enough to the site to give rise to potentially damaging earthquake ground motions, were identified. Seven active faults that have the potential for producing significant earthquakes and that pass through or near the dam site were also identified. The earthquake loading represented by ground motions at the site was evaluated. Probabilistic seismic hazard procedures were used for assessing the earthquake loading at six individual sites using Area-and Line-Source Models (ASM & LSM). The ASM is based on current observed seismicity, whereas the LSM is based on geological slip rates. The output represents the expected acceleration amplitude with 90 percent probability of not being exceeded in exposure times of 20, 50, and 100 years. The results from the two models appear to be different, the expected ground motions from ASM were twice as high as expected from LSM. This difference is due to the load of the Aswan reservoir (Nasser Lake) triggering earthquakes on those parts of the faults that lie under the lake at Kalabsha area. The hazard at the selected sites is given by the hazard curve that is represented by the relationship between the peak ground acceleration and its annual exceedance probability. By comparing the curves for the six individual sites for the same source model, it can be concluded that the potential ground acceleration level for all the sites is almost the same. Considering the mean results from the two models, the annual exceedance probability of the expected ground acceleration from ASM is approximately ten times higher than the annual exceedance probability from LSM.Since ASM is based on current seismicity, it is more appropriate forrepresenting the actual hazard for the dam site.     

Seismicity and tectonics of southern Central America and adjacent regions with special attention to the surroundings of Panama

Ten new focal mechanisms are derived for earthquakes in southern Central America and its adjacent regions. These are combined with a study of seismicity and data of previous workers to delineate the position and nature of the plate boundaries in this complex region.The Middle America subduction zone may be divided into four or five distinct seismic segments. The plate boundary between North America and the Caribbean near the trench might be located more towards the south than previously suspected. Subduction has basically stopped south of the underthrusting Cocos Ridge. There is not much evidence for a seismically active strike-slip fault south of Panama, but its existence cannot be ruled out. More activity reveals the zone north of Panama which is identified as a subduction zone with normal fault events. Shallow seismicity induced by the interaction of the Nazca plate extends from the Colombia-Panama border south along the Pacific coast to meet a high-angle continental thrust fault system. Subduction with a pronounced slab starts only south of that point near a hot region which offsets the seismic trend at the trench. The Carnegie Ridge and/or the change of direction of subduction in Ecuador produce a highly active zone of seismicity mainly at the depth of 200 km. The area in the Pacific displays a termination of activity at a propagating rift west of the Galapagos Islands. The main eastern boundary of the Cocos plate, the Panama Fracture Zone, is offset towards the west at the southern end of the Malpelo Ridge. Its northern end consists of two active branches as defined by large earthquakes. A strike-slip mechanism near the southeastern flank of the Cocos Ridge was previously believed to be the site of an extended fracture zone. This paper proposes submarine volcanic activity as an alternative explanation.     

Errors in expected human losses due to incorrect seismic hazard estimates

Seismic hazard maps are constructed by extrapolating from the frequency of small earthquakes, the annual probability of large, infrequent, earthquakes. Combining the potential contribution from all seismically active volumes, one calculates the peak ground acceleration with a probability to be exceeded by 10?% in 50?years at any given point. The consequential risk, the losses to be expected, derives from the damage the calculated shaking causes to buildings, and the impact on occupants due to collapsing structures. We show that the numbers of fatalities in recent disastrous earthquakes were underestimated by the world seismic hazard maps by approximately two to three orders of magnitude. Thus, seismic hazard maps based on the standard method cannot be used to estimate the risk to which the population is exposed due to large earthquakes.     

Probabilistic seismic hazard map of NW Himalaya and its adjoining area,India

The seismically active Northwest (NW) Himalaya falls within Seismic Zone IV and V of the hazard zonation map of India. The region has suffered several moderate (~25), large-to-great earthquakes (~4) since Assam earthquake of 1897. In view of the major advancement made in understanding the seismicity and seismotectonics of this region during the last two decades, an updated probabilistic seismic hazard map of NW Himalaya and its adjoining areas covering 28–34°N and 74–82°E is prepared. The northwest Himalaya and its adjoining area is divided into nineteen different seismogenic source zones; and two different region-specific attenuation relationships have been used for seismic hazard assessment. The peak ground acceleration (PGA) estimated for 10% probability of exceedance in 50 and 10 years at locations defined in the grid of 0.25 × 0.25°. The computed seismic hazard map reveals longitudinal variation in hazard level along the NW Himalayan arc. The high hazard potential zones are centred around Kashmir region (0.70 g/0.35 g), Kangra region (0.50 g/0.020 g), Kaurik-Spitti region (0.45 g/0.20 g), Garhwal region (0.50 g/0.20 g) and Darchula region (0.50 g/0.20 g) with intervening low hazard area of the order of 0.25 g/0.02 g for 10% probability in 50 and 10 years in each region respectively.     

Comprehensive seismic hazard assessment of Tripura and Mizoram states

Northeast India is one of the most highly seismically active regions in the world with more than seven earthquakes on an average per year of magnitude 5.0 and above. Reliable seismic hazard assessment could provide the necessary design inputs for earthquake resistant design of structures in this region. In this study, deterministic as well as probabilistic methods have been attempted for seismic hazard assessment of Tripura and Mizoram states at bedrock level condition. An updated earthquake catalogue was collected from various national and international seismological agencies for the period from 1731 to 2011. The homogenization, declustering and data completeness analysis of events have been carried out before hazard evaluation. Seismicity parameters have been estimated using G–R relationship for each source zone. Based on the seismicity, tectonic features and fault rupture mechanism, this region was divided into six major subzones. Region specific correlations were used for magnitude conversion for homogenization of earthquake size. Ground motion equations (Atkinson and Boore 2003; Gupta 2010) were validated with the observed PGA (peak ground acceleration) values before use in the hazard evaluation. In this study, the hazard is estimated using linear sources, identified in and around the study area. Results are presented in the form of PGA using both DSHA (deterministic seismic hazard analysis) and PSHA (probabilistic seismic hazard analysis) with 2 and 10% probability of exceedance in 50 years, and spectral acceleration (T = 0. 2 s, 1.0 s) for both the states (2% probability of exceedance in 50 years). The results are important to provide inputs for planning risk reduction strategies, for developing risk acceptance criteria and financial analysis for possible damages in the study area with a comprehensive analysis and higher resolution hazard mapping.     

Seismic Hazard and Loss Estimation for Central America

A new methodology of seismic hazard and loss estimation has been proposed by Chen et al. (Chen et al., 1998; Chan et al., 1998) for the study of global seismic risk. Due to its high adaptability for regions of different features and scales, the methodology was applied to Central America. Seismic hazard maps in terms of both macro-seismic intensity and peak ground acceleration (PGA) at 10% probability of exceedance in 50 years are provided. The maps are all based on the global instrumental as well as historical seismic catalogs and available attenuation relations. Employing the population-weighted gross domestic product (GDP) data, the expected earthquake loss in 50 years for Central America is also estimated at a 5' latitude × 5' longitude resolution. Besides the seismic risk index, a measure of the relative loss or risk degree is calculated for each individual country within the study area. The risk index may provide a useful tool to help allocations of limited mitigation resources and efforts for the purpose of reduction of seismic disasters. For expected heavy loss locations, such as the Central American capital cities, earthquake scenario analysis is helpful in providing a quick overview of loss distribution assuming a major event occurs there. Examples of scenario analysis are given for San Jose, capital of Costa Rica, and Panama City, capital of Panama, respectively.     

The spatial correlation between earthquakes and landslides in Hokkaido (Japan), a GIS-based analysis of the past and the future

Although earthquakes are thought to be one of the factors responsible for the occurrence of landslides in Hokkaido, there exist no enough records which can allow correlating many of the old slope failures in the island with earthquakes. In the absence of these records, an attempt was done in this study to use the abundance, frequency, magnitude, depth, and distribution of historical earthquakes to deduce that many of the slope failures in the region were triggered by strong and continuous seismicity. The determination of the zones of influences of selected earthquakes using an existing empirical function has also supported this conclusion. Moreover, the use of a 10% probability of exceedance of earthquake intensity in 50 years, and the geological and slope maps has allowed preparing a landslide hazard map which explains the role of future earthquakes in the formation of slope failures. The result indicates a high probability of occurrences of landslides in the hilly regions of the southeastern part of Hokkaido due to expected strong seismicity and earthquake intensities in these areas. On the other hand, the low level of intensity in the north has given rise to low probability of landslide hazard. There are also places in the center of the island and high intensity regions in the east where the probability of landslide hazard was influenced by the contribution of the geological and slope maps.     

Non-Poisson probabilistic seismic hazard assessment

The development of the new seismic hazard map of metropolitan Tehran is based on probabilistic seismic hazard computation using the non-Poisson recurrence time model. For this model, two maps have been prepared to indicate the earthquake hazard of the region in the form of iso-acceleration contour lines. They display the non-Poisson probabilistic estimates of peak ground accelerations over bedrock for 10 and 63 % probability of exceedance in 50 years. To carry out the non-Poisson seismic hazard analysis, appropriate distributions of interoccurrence times of earthquakes were used for the seismotectonic provinces which the study region is located and then the renewal process was applied. In order to calculate the seismic hazard for different return periods in the probabilistic procedure, the study area encompassed by the 49.5–54.5°E longitudes and 34–37°N latitudes was divided into 0.1° intervals generating 1,350 grid points. PGA values for this region are estimated to be 0.30–0.32 and 0.16–0.17 g for 10 and 63 % probability of exceedance, respectively, in 50 years for bedrock condition.     

Seismic hazard at a triple plate junction: the state of Chiapas (México)

The state of Chiapas (SE México) conforms a territory of complex tectonics and high seismic activity. The interaction among the Cocos, North American and Caribbean tectonic plates, as well as the active crustal deformation inside Chiapas, determines a variety of seismogenic sources of distinct characteristics and particular strong ground motion attenuation. This situation makes the assessment of seismic hazard in the region a challenging task. In this work, we follow the methodology of probabilistic seismic hazard analysis, starting from the compilation of an earthquake catalogue, and the definition of seismogenic source-zones based on the particular seismotectonics of the region: plate-subduction-related sources (interface and intraslab zones), active crustal deformation zones and the shear zone between the North American and Caribbean plates formed by the Motagua, Polochic and Ixcán faults. The latter source is modelled in two different configurations: one single source-zone and three distinct ones. We select three ground motion prediction equations (GMPEs) recommended for South and Central America, plus two Mexican ones. We combine the GMPEs with the source-zone models in a logic tree scheme and produce hazard maps in terms of peak ground acceleration and spectral acceleration for the 500-, 1000- and 2500-year return periods, as well as uniform hazard spectra for the towns of Tuxtla Gutiérrez, Tapachula and San Cristóbal. We obtain higher values in comparison with previous seismic hazard studies and particularly much higher than the output of the Prodisis v.2.3 software for seismic design in México. Our results are consistent with those of neighbouring Guatemala obtained in a recent study for Central America.

     

Historical seismicity in Mexico during 1568–1837: intensity evaluation and data reliability

Iso-intensity contour maps were calculated on the basis of the intensity data derived from historical information about strongest earthquakes in Mexico. Intensity data contain a great deal of information that can be used to constrain the essential characteristics of the seismic source. In particular, both the seismological theory and its practice suggest that the orientation of the source of significant earthquakes is reflected in the elongation of the associated damage pattern. The present paper uses information about historical seismicity in Mexico from 1568 to 1837 to point out the sites, where the strongest damages took place. After information selection, maps of iso-intensities were built to determine epicentres. This information was interpreted, and damages and major risk zones were mapped. The systematic application of this method to all the M > 5.5 earthquakes that occurred in Mexico in the past five centuries produced encouraging results about the determination of the seismic source parameters that compare well with existing instrumental, geological, and geodynamic evidence.     

Global Seismic Hazard Assessment Based on Area Source Model and Seismicity Data

A global seismic hazard assessment was conducted using the probabilistic approach in conjunction with a modified means of evaluating the seismicity parameters. The earthquake occurrence rate function was formulated for area source cells from recent instrumental earthquake catalogs. For the statistical application of the G–R relation of each source cell, the upper- and lower-bound magnitudes were determined from, respectively, historical earthquake data using a Kernel smoothing operator and detection thresholds of recent catalogs. The seismic hazard at a particular site was obtained by integrating the hazard contribution from influencing cells, and the results were combined with the Poisson distribution to obtain the seismic hazard in terms of the intensity at 10% probability of exceedance for the next 50 years. The seismic hazard maps for three countries, constructed using the same method, agree well with the existing maps obtained by different methods. The method is applicable to both oceanic and continental regions, and for any specific duration of time. It can be used for those regions without detailed geological information or where the relation between existing faults and earthquake occurrence is not clear.     

Seismicity of Gujarat

Paper describes tectonics, earthquake monitoring, past and present seismicity, catalogue of earthquakes and estimated return periods of large earthquakes in Gujarat state, western India. The Gujarat region has three failed Mesozoic rifts of Kachchh, Cambay, and Narmada, with several active faults. Kachchh district of Gujarat is the only region outside Himalaya-Andaman belt that has high seismic hazard of magnitude 8 corresponding to zone V in the seismic zoning map of India. The other parts of Gujarat have seismic hazard of magnitude 6 or less. Kachchh region is considered seismically one of the most active intraplate regions of the World. It is known to have low seismicity but high hazard in view of occurrence of fewer smaller earthquakes of M????6 in a region having three devastating earthquakes that occurred during 1819 (M _w7.8), 1956 (M _w6.0) and 2001 (M _w7.7). The second in order of seismic status is Narmada rift zone that experienced a severely damaging 1970 Bharuch earthquake of M5.4 at its western end and M????6 earthquakes further east in 1927 (Son earthquake), 1938 (Satpura earthquake) and 1997 (Jabalpur earthquake). The Saurashtra Peninsula south of Kachchh has experienced seismicity of magnitude less than 6.     

A Case Study of the Spatial Distribution of Seismic Hazard (El Salvador)

The republic of El Salvador in Central America is an area of high seismic hazard where at least twelve destructive earthquakes have occurred this century alone. The principal sources of seismic hazard are earthquakes associated with the subduction of the Cocos plate in the Middle America Trench and upper-crustal earthquakes in the chain of Quaternary volcanoes that runs across the country parallel to the subduction trench. Hazard assessments for Central America have suggested almost uniform distribution of hazard throughout El Salvador. Seismic zonations for three successive building codes in El Salvador simply divide the country into two regions, with the higher hazard zone containing the volcanoes and the coastal areas. Historical records suggest that the greatest hazard is posed by the upper-crustal earthquakes concentrated on the volcanic centres which, although of smaller magnitude than the subduction events, are generally of shallow focus and coincide with the main population centres. These earthquakes have repeatedly caused intense damage over small areas in the vicinity of some of the main volcanoes. This study focuses on El Salvador to explore the capability of different approaches to hazard assessment to reflect significant variations of seismic hazard within small geographical areas. In the study, three 'zone-free' methods are employed as well as the Cornell–McGuire approach. The results of the assessments are compared and their implications for seismic zoning for construction and insurance purposes are discussed.     

Probabilistic seismic hazard analysis for Sumatra, Indonesia and across the Southern Malaysian Peninsula

The ground motion hazard for Sumatra and the Malaysian peninsula is calculated in a probabilistic framework, using procedures developed for the US National Seismic Hazard Maps. We constructed regional earthquake source models and used standard published and modified attenuation equations to calculate peak ground acceleration at 2% and 10% probability of exceedance in 50 years for rock site conditions. We developed or modified earthquake catalogs and declustered these catalogs to include only independent earthquakes. The resulting catalogs were used to define four source zones that characterize earthquakes in four tectonic environments: subduction zone interface earthquakes, subduction zone deep intraslab earthquakes, strike-slip transform earthquakes, and intraplate earthquakes. The recurrence rates and sizes of historical earthquakes on known faults and across zones were also determined from this modified catalog. In addition to the source zones, our seismic source model considers two major faults that are known historically to generate large earthquakes: the Sumatran subduction zone and the Sumatran transform fault. Several published studies were used to describe earthquakes along these faults during historical and pre-historical time, as well as to identify segmentation models of faults. Peak horizontal ground accelerations were calculated using ground motion prediction relations that were developed from seismic data obtained from the crustal interplate environment, crustal intraplate environment, along the subduction zone interface, and from deep intraslab earthquakes. Most of these relations, however, have not been developed for large distances that are needed for calculating the hazard across the Malaysian peninsula, and none were developed for earthquake ground motions generated in an interplate tectonic environment that are propagated into an intraplate tectonic environment. For the interplate and intraplate crustal earthquakes, we have applied ground-motion prediction relations that are consistent with California (interplate) and India (intraplate) strong motion data that we collected for distances beyond 200 km. For the subduction zone equations, we recognized that the published relationships at large distances were not consistent with global earthquake data that we collected and modified the relations to be compatible with the global subduction zone ground motions. In this analysis, we have used alternative source and attenuation models and weighted them to account for our uncertainty in which model is most appropriate for Sumatra or for the Malaysian peninsula. The resulting peak horizontal ground accelerations for 2% probability of exceedance in 50 years range from over 100% g to about 10% g across Sumatra and generally less than 20% g across most of the Malaysian peninsula. The ground motions at 10% probability of exceedance in 50 years are typically about 60% of the ground motions derived for a hazard level at 2% probability of exceedance in 50 years. The largest contributors to hazard are from the Sumatran faults.     

Crustal deformation in northern Central America

Evaluation of the seismic moment tensor for earthquakes on plate boundary is a standard procedure to determine the relative velocity of plates, which controls the seismic deformation rate predicted from the slip on a single fault. The moment tensor is also decomposed into an isotropic and a deviatoric part to discover the relationship between the average strain rate and the relative velocity between two plates. We utilize this procedure to estimate the rates of deformation in northern Central America where plate boundaries are seismically well defined. Four different tectonic environments are considered for modelling of the plate motions. The deformation rates obtained here compare well with those predicted from the plate motions models and are in good agreement with actual observations. Deformation rates on faults are increasingly being used to estimate earthquake recurrence from information on fault slip rate and more on how we can incorporate our current understanding into seismic hazard analyses.     

Seismic input at the archaeological site of Kancheepuram in Southern India

A probabilistic seismic hazard assessment at Kancheepuram in Southern India was carried out with the scope of defining the seismic input for the vulnerability assessment of historical and monumental structures at the site, in terms of horizontal Uniform Hazard Spectra and a suite of spectrum-compatible natural accelerograms to perform time-history analysis. The standard Cornell?CMcGuire and a zone-free approach have been used for hazard computations after the compilation of a composite earthquake catalogue for Kancheepuram. Epistemic uncertainty in the seismic hazard was addressed within a logic-tree framework. Deaggregation of the seismic hazard for the peak ground acceleration shows low seismicity at Kancheepuram controlled by weak-to-moderate earthquakes with sources located at short distances from the archaeological site. Suites of natural accelerograms recorded on rock have been selected by imposing a custom-defined compatibility criterion with the probabilistic spectra. The site of Kancheepuram is characterized by a seismicity controlled by weak-to-moderate earthquakes with sources at short distances from the site, the PGA expected for 475- and 2,475-year return period are, respectively, 0.075 and 0.132?g. The Indian code-defined spectra (DBE and MCE) tend to underestimate spectral ordinates at low periods. On the other hand, the PGA are comparable and the spectral ordinates for longer periods from the probabilistic study are significantly lower.     

A New Probabilistic Seismic Hazard Analysis for the Vrancea (Romania) Seismogenic Zone

In this paper we apply a probabilistic methodology to map specific seismic hazard induced by the Vrancea Seismogenic Zone, which represents the uttermost earthquake danger to Romania as well as its surroundings. The procedure is especially suitable for the estimation of seismic hazard at an individual site, and seismic hazard maps can be created by applying it repeatedly to grid points covering larger areas. It allows the use of earthquake catalogues with incompletely reported historical and complete instrumental parts. When applying themethodology, special attention was given to the effect of hypocentral depth and the variation of attenuation according to azimuth. Hazard maps specifying a 10% chance of exceedance of the given peak ground acceleration value for an exposure time of 50 years were prepared for three different characteristic depths of earthquakes in the Vrancea area. These maps represent a new realistic contribution to the mitigation of the earthquake risk caused by the Vrancea Seismogenic Zone in terms of: (1) input data (consistent, reliable, and the most complete earthquake catalogue), (2) appropriate and specific attenuation relationships (considering both azimuthal and depth effects); and (3) a new and versatile methodology.