Reducing monitoring gaps at the aquifer–river interface by modelling groundwater–surface water exchange flow patterns

This study investigates spatial patterns and temporal dynamics of aquifer–river exchange flow at a reach of the River Leith, UK. Observations of sub‐channel vertical hydraulic gradients at the field site indicate the dominance of groundwater up‐welling into the river and the absence of groundwater recharge from surface water. However, observed hydraulic heads do not provide information on potential surface water infiltration into the top 0–15 cm of the streambed as these depths are not covered by the existing experimental infrastructure. In order to evaluate whether surface water infiltration is likely to occur outside the ‘window of detection’, i.e. the shallow streambed, a numerical groundwater model is used to simulate hydrological exchanges between the aquifer and the river. Transient simulations of the successfully validated model (Nash and Sutcliff efficiency of 0·91) suggest that surface water infiltration is marginal and that the possibility of significant volumes of surface water infiltrating into non‐monitored shallow streambed sediments can be excluded for the simulation period. Furthermore, the simulation results show that with increasing head differences between river and aquifer towards the end of the simulation period, the impact of streambed topography and hydraulic conductivity on spatial patterns of exchange flow rates decreases. A set of peak flow scenarios with altered groundwater‐surface water head gradients is simulated in order to quantify the potential for surface water infiltration during characteristic winter flow conditions following the observation period. The results indicate that, particularly at the beginning of peak flow conditions, head gradients are likely to cause substantial increase in surface water infiltration into the streambed. The study highlights the potential for the improvement of process understanding of hyporheic exchange flow patterns at the stream reach scale by simulating aquifer‐river exchange fluxes with a standard numerical groundwater model and a simple but robust model structure and parameterization. Copyright © 2011 John Wiley & Sons, Ltd.     

Delineating and quantifying ground water discharge zones using streambed temperatures

Streambed temperature mapping, hydraulic testing using minipiezometers, and geochemical analyses of interstitial water of the streambed were used to delineate the pattern of ground water discharge in a sandy streambed and to develop a flux-based conceptual model for ground water/surface water interactions. A new and simple empirical method was used to relate fluxes obtained from minipiezometer data to streambed temperatures. The relationship allowed flux to be calculated at locations where only streambed temperature measurements were made. Slug testing and potentiomanometer measurements at 34 piezometers indicated ground water discharge ranged from 0.03 to 446 L/m2/day (and possibly as high as 7060 L/m2/day) along a 60 m long by 11 to 14 m wide reach of river. Complex but similar plan-view patterns of flux were calculated for both summer and winter using hundreds of streambed temperatures measured on a 1 by 2 m grid. The reach was dominated by ground water discharge and 5% to 7% of the area accounted for approximately 20% to 24% of the total discharge. < 12% of the total area consisted of recharge zones or no-discharge zones. A conceptual model for ground water/surface water interactions consisting of five different behaviors was developed based on the magnitude and direction of flux across the surface of the streambed. The behaviors include short-circuit discharge (e.g., high-flow springs), high discharge (e.g., preferential flowpaths), low to moderate discharge, no discharge (e.g., horizontal hyporheic or ground water flow), and recharge. Geological variations at depth played a key role in determining which type of flow behavior occurred in the streambed.     

Deducing the spatial variability of exchange within a longitudinal channel water balance

Developing an appropriate data collection scheme to infer stream–subsurface interactions is not trivial due to the spatial and temporal variability of exchange flowpaths. Within the context of a case study, this paper presents the results from a number of common data collection techniques ranging from point to reach scales used in combination to better understand the spatial complexity of subsurface exchanges, infer the hydrologic conditions where individual influences of hyporheic and groundwater exchange components on stream water can be characterized, and determine where gaps in information arise. We start with a tracer‐based, longitudinal channel water balance to quantify hydrologic gains and losses at a sub‐reach scale nested within two consecutive reaches. Next, we look at groundwater and stream water surface levels, shallow streambed vertical head gradients, streambed and aquifer hydraulic conductivities, water chemistry, and vertical flux rates estimated from streambed temperatures to provide more spatially explicit information. As a result, a clearer spatial understanding of gains and losses was provided, but some limitations in interpreting results were identified even when combining information collected over various scales. Due to spatial variability of exchanges and areas of mixing, each technique frequently captured a combination of groundwater and hyporheic exchange components. Ultimately, this study provides information regarding technique selection, emphasizes that care must be taken when interpreting results, and identifies the need to apply or develop more advanced methods for understanding subsurface exchanges. Copyright © 2013 John Wiley & Sons, Ltd.     

Air/water/sediment temperature contrasts in small streams to identify groundwater seepage locations

The need to identify groundwater seepage locations is of great importance for managing both stream water quality and groundwater sourced ecosystems due to their dependency on groundwater‐borne nutrients and temperatures. Although several reconnaissance methods using temperature as tracer exist, these are subjected to limitations related to mainly the spatial and temporal resolution and/or mixing of groundwater and surface water leading to dilution of the temperature differences. Further, some methods, for example, thermal imagery and fiber optic distributed temperature sensing, although relative efficient in detecting temperature differences over larger distances, these are labor‐intensive and costly. Therefore, there is a need for additional cost‐effective methods identifying substantial groundwater seepage locations. We present a method expanding the linear regression of air and stream temperatures by measuring the temperatures in dual‐depth; in the stream column and at the streambed‐water interface (SWI). By doing so, we apply metrics from linear regression analysis of temperatures between air/stream and air/SWI (linear regression slope, intercept, and coefficient of determination), and the daily water temperature cycle (daily mean temperatures, temperature variance, and the mean diel temperature fluctuation). We show that using metrics from only single‐depth stream temperature measurements are insufficient to identify substantial groundwater seepage locations in a head‐water stream. Conversely, comparing the metrics from dual‐depth temperatures show significant differences; at groundwater seepage locations, temperatures at the SWI merely explain 43–75% of the variation opposed to ? 91% at the corresponding stream column temperatures. In general, at these locations at the SWI, the slopes ( < 0.25) and intercepts ( > 6.5 °C) are substantially lower and higher, respectively, while the mean diel temperature fluctuations ( < 0.98 °C) are decreased compared to remaining locations. The dual‐depth approach was applied in a post‐glacial fluvial setting, where metrics analyses overall corroborated with field measurements of groundwater fluxes and stream flow accretions. Thus, we propose a method reliably identifying groundwater seepage locations along streambeds in such settings.     

Comparison of two modeling approaches for groundwater–surface water interactions

An assessment of interactions between groundwater and surface water was carried out by applying two different modeling approaches to a small‐scale study area in the municipality of Havelock, Quebec. The first approach involved a commonly used sequential procedure that consists in determining the daily recharge rate using a quasi 2D infiltration model (HELP), applied in the next step as an imposed flux to a 3D finite‐element groundwater flow model. The flow model was calibrated under steady‐state and transient conditions against measured water levels. The second approach was based on a recently developed physically based, 3D fully coupled groundwater–surface water flow model (CATHY) applied to the entire flow domain in an integrated manner. Implementation, calibration, and results of the simulations for both approaches are presented and discussed. For equal annual precipitation (1038 mm/y) and evapotranspiration (556 mm/y), the second approach computed a recharge rate of 233 mm/y (8.9% higher than the first approach) and a net upward flow from the fractured aquifer (the first approach predicted a net downward flow to the rock). The simulated annual discharge was similar for the two approaches (9.6% difference). Both approaches were found to be useful in understanding the interactions between groundwater and surface water, although limitations are apparent in the sequential procedure's inability to account for surface–subsurface feedbacks, for instance near stream reaches where groundwater discharge is prevalent. The decoupled, two‐model approach provides disaggregated surface, vadose, and aquifer flows, and a simple aperçu at the different components of total discharge. The fully coupled model accounts for continuous water exchanges between the land surface, subsurface, and stream channel in a more complex manner, and produces a better match against observed data. Copyright © 2012 John Wiley & Sons, Ltd.     

From streambed temperature measurements to spatial‐temporal flux quantification: using the LPML method to study groundwater–surface water interaction

Knowledge on groundwater–surface water interaction and especially on exchange fluxes between streams and aquifers is an important prerequisite for the study of transport and fate of contaminants and nutrients in the hyporheic zone. One possibility to quantify groundwater–surface water exchange fluxes is by using heat as an environmlental tracer. Modern field equipment including multilevel temperature sticks and the novel open‐source analysis tool LPML make this technique ever more attractive. The recently developed LPML method solves the one‐dimensional fluid flow and heat transport equation by combining a local polynomial method with a maximum likelihood estimator. In this study, we apply the LPML method on field data to quantify the spatial and temporal variability of vertical fluxes and their uncertainties from temperature–time series measured in a Belgian lowland stream. Over several months, temperature data were collected with multilevel temperature sticks at the streambed top and at six depths for a small stream section. Long‐term estimates show a range from gaining fluxes of ?291 mm day^?1 to loosing fluxes of 12 mm day^?1; average seasonal fluxes ranged from ?138 mm day^?1 in winter to ?16 mm day^?1 in summer. With our analyses, we could determine a high spatial and temporal variability of vertical exchange fluxes for the investigated stream section. Such spatial and temporal variability should be taken into account in biogeochemical cycling of carbon, nutrients and metals and in fate analysis of contaminant plumes. In general, the stream section was gaining during most of the observation period. Two short‐term high stream stage events, seemingly caused by blockage of the stream outlet, led to a change in flow direction from gaining to losing conditions. We also found more discharge occurring at the outer stream bank than at the inner one indicating a local flow‐through system. With the conducted analyses, we were able to advance our understanding of the regional groundwater flow system. Copyright © 2015 John Wiley & Sons, Ltd.     

Quantitative guidance for efficient vertical flow measurements at the sediment–water interface using temperature–depth profiles

Upward discharge to surface water bodies can be quantified using analytical models based on temperature–depth (T-z) profiles. The use of sediment T-z profiles is attractive as discharge estimates can be obtained using point-in-time data that are collected inexpensively and rapidly. Previous studies have identified that T-z methods can only be applied at times of the year when there is significant difference between the streambed–water interface and deeper sediment temperatures (e.g., winter and summer). However, surface water temperatures also vary diurnally, and the influence of these variations on discharge estimates from T-z methods is poorly understood. For this study, synthetic T-z profiles were generated numerically using measured streambed interface temperature data to assess the influence of diurnal temperature variations on discharge estimation and provide insight into the suitable application of T-z methods. Results show that the time of day of data collection can have a substantial influence on vertical flux estimates using T-z methods. For low groundwater discharge fluxes (e.g., 0.1 m d⁻¹), daily transience in streambed temperatures led to relatively large errors in estimated flow magnitude and direction. For higher discharge fluxes (1.5 m d⁻¹), the influence of transient streambed temperatures on discharge estimates was strongly reduced. Discharge estimates from point-in-time T-z profiles were most accurate when the uppermost point in the T-z profile was near the bed interface daily mean (two time periods daily). Where temperature time series data are available, daily averaged T-z profiles can produce accurate discharge estimates across a wide range of discharge rates. Seasonality in shallow groundwater temperature generally had a negligible influence on vertical flow estimates. These findings can be used to plan field campaigns and provide guidance on the optimal application of T-z methods to quantify vertical groundwater discharge to surface water bodies.     

Influence of water flux and redox conditions on chlorobenzene concentrations in a contaminated streambed

Significant natural attenuation may occur on the passage of groundwater plumes through streambed sediments because of the transition from anaerobic to aerobic conditions and an increased microbial activity. Varying directions and magnitudes of water flow in the streambed may enhance or inhibit the supply of oxygen to the streambed and thus influence the redox zoning. In a field study at a small stream in the industrial area of Bitterfeld‐Wolfen, we observed the variability of hydraulic gradients, streambed temperatures, redox conditions and monochlorobenzene (MCB) concentrations in the streambed over the course of 5 months. During the observation period, the hydrologic conditions changed from losing to gaining. Accordingly, the temperature‐derived water fluxes changed from recharge to discharge. Redox conditions were highly variable between ? 170 and 368 mV in the shallow streambed at a depth of 0·1 m below the streambed surface. Deeper in the streambed, at depths of 0·3 m and 0·5 m, the redox conditions were more stable between ? 198 and ? 81 mV and comparable to those typically found in the aquifer. MCB concentrations in the streambed at 0·3 and 0·5 m depth increased with increasing upward water flux. The MCB concentrations in the shallow streambed at 0·1 m depth appeared to be independent of the hydrologic conditions suggesting that degradation of MCB may have occured. Copyright © 2010 John Wiley & Sons, Ltd.     

Application of Distributed Temperature Sensing for coupled mapping of sedimentation processes and spatio‐temporal variability of groundwater discharge in soft‐bedded streams

The delineation of groundwater discharge areas based on Distributed Temperature Sensing (DTS) data of the streambed can be difficult in soft‐bedded streams where sedimentation and scouring processes constantly change the position of the fibre optic cable relative to the streambed. Deposition‐induced temperature anomalies resemble the signal of groundwater discharge while scouring will cause the cable to float in the water column and measure stream water temperatures. DTS applied in a looped layout with nine fibre optic cable rows in a 70 × 5 m section of a soft‐bedded stream made it possible to detect variability in streambed temperatures between October 2011 and January 2012. Detailed monthly streambed elevation surveys were carried out to monitor the position of the fibre optic cable relative to the streambed and to quantify the effect of sedimentation processes on streambed temperatures. Based on the simultaneous interpretation of streambed temperature and elevation data, a method is proposed to delineate potential high‐groundwater discharge areas and identify deposition‐induced temperature anomalies in soft‐bedded streams. Potential high‐discharge sites were detected using as metrics the daily minimum, maximum and mean streambed temperatures as well as the daily amplitude and standard deviation of temperatures. The identified potential high‐discharge areas were mostly located near the channel banks, also showing temporal variability because of the scouring and redistribution of streambed sediments, leading to the relocation of pool‐riffle sequences. This study also shows that sediment deposits of 0.1 m thickness already resulted in an increase in daily minimum streambed temperatures and decrease in daily amplitude and standard deviation. Scouring sites showed lower daily minimum streambed temperatures and higher daily amplitude and standard deviation compared with areas without sedimentation and scouring. As a limitation of the approach, groundwater discharge occurring at depositional and scouring areas cannot be identified by the metrics applied. Copyright © 2015 John Wiley & Sons, Ltd.     

Surface water–groundwater interaction at restored streams and associated reference reaches

Stream restoration goals include improving habitat and water quality through reconstruction of morphological features found at analogous, pristine stream reaches. Enhancing hyporheic exchange may facilitate achieving these goals. Although hyporheic exchange at restoration sites has been explored in a few previous studies, comparative studies of restored versus reference or control streams are largely absent. We hypothesized that restoration cross‐vanes enhance hyporheic exchange, resulting in biogeochemical alteration of stream water chemistry in the streambed. Two streams restored using cross‐vanes to control erosion and improve habitat were compared with their associated reference reaches, which provided the basis for the restoration design. Thirteen temperature profile rods with vertically stacked sensors were installed at each site for 2 weeks. Heat tracing was used to quantify vertical flux in the streambed from the diurnal temperature fluctuations in the subsurface. Stream water and bed pore waters from mini‐piezometers were analysed for ion and nutrient chemistry. In general, mean vertical flux rates through the streambed were small throughout reference sites (?0.3 to 0.3 m/day) and at most locations at restored sites. Immediately adjacent to cross‐vanes, vertical flux rates were larger (up to 3.5 m/day). Geochemistry of pore waters shows distinct differences in the sources for the reference and restored sites. Strong downwelling zones adjacent to cross‐vanes showed high dissolved oxygen (10.75 mg/l) and geochemistry in the streambed similar to surface water. Reference sites had lower dissolved oxygen in the streambed (0.66–5.14 mg/l), and geochemical patterns suggest a mixture of discharging groundwater and surface water in the hyporheic zone. Restored sites also clearly show sulfate and nitrate reduction occurring in the streambed, which is not observed at the reference sites. The stream restoration sites studied here enhance rapid hyporheic exchange, but upwelling of groundwater has a stronger influence on streambed geochemistry at reference sites. Copyright © 2012 John Wiley & Sons, Ltd.     

Assimilation of historical head data to estimate spatial distributions of stream bed and aquifer hydraulic conductivity fields

Management of water resources in alluvial aquifers relies mainly on understanding interactions between hydraulically connected streams and aquifers. Numerical models that simulate this interaction often are used as decision support tools for water resource management. However, the accuracy of numerical predictions relies heavily on unknown system parameters (e.g., streambed conductivity and aquifer hydraulic conductivity), which are spatially heterogeneous and difficult to measure directly. This paper employs an ensemble smoother to invert groundwater level measurements to jointly estimate spatially varying streambed and alluvial aquifer hydraulic conductivity along a 35.6‐km segment of the South Platte River in Northeastern Colorado. The accuracy of the inversion procedure is evaluated using a synthetic experiment and historical groundwater level measurements, with the latter constituting the novelty of this study in the inversion and validation of high‐resolution fields of streambed and aquifer conductivities. Results show that the estimated streambed conductivity field and aquifer conductivity field produce an acceptable agreement between observed and simulated groundwater levels and stream flow rates. The estimated parameter fields are also used to simulate the spatially varying flow exchange between the alluvial aquifer and the stream, which exhibits high spatial variability along the river reach with a maximum average monthly aquifer gain of about 2.3 m³/day and a maximum average monthly aquifer loss of 2.8 m³/day, per unit area of streambed (m²). These results demonstrate that data assimilation inversion provides a reliable and computationally affordable tool to estimate the spatial variability of streambed and aquifer conductivities at high resolution in real‐world systems.     

Numerical modelling of stream–aquifer interaction: Quantifying the impact of transient streambed permeability and aquifer heterogeneity

Stream–aquifer interaction plays a vital role in the water cycle, and a proper study of this interaction is needed for understanding groundwater recharge, contaminants migration, and for managing surface water and groundwater resources. A model‐based investigation of a field experiment in a riparian zone of the Schwarzbach river, a tributary of the Rhine River in Germany, was conducted to understand stream–aquifer interaction under alternative gaining and losing streamflow conditions. An equivalent streambed permeability, estimated by inverting aquifer responses to flood waves, shows that streambed permeability increased during infiltration of stream water to aquifer and decreased during exfiltration. Aquifer permeability realizations generated by multiple‐point geostatistics exhibit a high degree of heterogeneity and anisotropy. A coupled surface water groundwater flow model was developed incorporating the time‐varying streambed permeability and heterogeneous aquifer permeability realizations. The model was able to reproduce varying pressure heads at two observation wells near the stream over a period of 55 days. A Monte Carlo analysis was also carried out to simulate groundwater flow, its age distribution, and the release of a hypothetical wastewater plume into the aquifer from the stream. Results of this uncertainty analysis suggest (a) stream–aquifer exchange flux during the infiltration periods was constrained by aquifer permeability; (b) during exfiltration, this flux was constrained by the reduced streambed permeability; (c) the effect of temporally variable streambed permeability and aquifer heterogeneity were found important to improve the accurate capture of the uncertainty; and (d) probabilistic infiltration paths in the aquifer reveal that such pathways and the associated prediction of the extent of the contaminant plume are highly dependent on aquifer heterogeneity.     

Improved simulation of river water and groundwater exchange in an alluvial plain using the SWAT model

Hydrological interaction between surface and subsurface water systems has a significant impact on water quality, ecosystems and biogeochemistry cycling of both systems. Distributed models have been developed to simulate this function, but they require detailed spatial inputs and extensive computation time. The soil and water assessment tool (SWAT) model is a semi‐distributed model that has been successfully applied around the world. However, it has not been able to simulate the two‐way exchanges between surface water and groundwater. In this study, the SWAT‐landscape unit (LU) model – based on a catena method that routes flow across three LUs (the divide, the hillslope and the valley) – was modified and applied in the floodplain of the Garonne River. The modified model was called SWAT‐LUD. Darcy's equation was applied to simulate groundwater flow. The algorithm for surface water‐level simulation during flooding periods was modified, and the influence of flooding on groundwater levels was added to the model. Chloride was chosen as a conservative tracer to test simulated water exchanges. The simulated water exchange quantity from SWAT‐LUD was compared with the output of a two‐dimensional distributed model, surface–subsurface water exchange model. The results showed that simulated groundwater levels in the LU adjoining the river matched the observed data very well. Additionally, SWAT‐LUD model was able to reflect the actual water exchange between the river and the aquifer. It showed that river water discharge has a significant influence on the surface–groundwater exchanges. The main water flow direction in the river/groundwater interface was from groundwater to river; water that flowed in this direction accounted for 65% of the total exchanged water volume. The water mixing occurs mainly during high hydraulic periods. Flooded water was important for the surface–subsurface water exchange process; it accounted for 69% of total water that flowed from the river to the aquifer. The new module also provides the option of simulating pollution transfer occurring at the river/groundwater interface at the catchment scale. Copyright © 2015 John Wiley & Sons, Ltd.     

Simulation of less‐mobile porosity dynamics in contrasting sediment water interface porous media

Considering heterogeneity in porous media pore size and connectivity is essential to predicting reactive solute transport across interfaces. However, exchange with less‐mobile porosity is rarely considered in surface water/groundwater recharge studies. Previous research indicates that a combination of pore‐fluid sampling and geoelectrical measurements can be used to quantify less‐mobile porosity exchange dynamics using the time‐varying relation between fluid and bulk electrical conductivity. For this study, we use macro‐scale (10 s of cm) advection–dispersion solute transport models linked with electrical conduction in COMSOL Multiphysics to explore less‐mobile porosity dynamics in two different types of observed sediment water interface porous media. Modeled sediment textures contrast from strongly layered streambed deposits to poorly sorted lakebed sands and cobbles. During simulated ionic tracer perturbations, a lag between fluid and bulk electrical conductivity, and the resultant hysteresis, is observed for all simulations indicating differential loading of pore spaces with tracer. Less‐mobile exchange parameters are determined graphically from these tracer time series data without the need for inverse numerical model simulation. In both sediment types, effective less‐mobile porosity exchange parameters are variable in response to changes in flow direction and fluid flux. These observed flow‐dependent effects directly impact local less‐mobile residence times and associated contact time for biogeochemical reaction. The simulations indicate that for the sediment textures explored here, less‐mobile porosity exchange is dominated by variable rates of advection through the domain, rather than diffusion of solute, for typical low‐to‐moderate rate (approximately 3–40 cm/day) hyporheic fluid fluxes. Overall, our model‐based results show that less‐mobile porosity may be expected in a range of natural hyporheic sediments and that changes in flowpath orientation and magnitude will impact less‐mobile exchange parameters. These temporal dynamics can be assessed with the geoelectrical experimental tracer method applied at laboratory and field scales.     

Quantification of vertical water fluxes in the vadose zone using particle‐size distribution and pedology‐based approaches to model soil heterogeneities

One‐dimensional flow simulations were conducted at four locations of the shallow alluvial aquifer of the upper Rhine River (at the Erstein polder) to quantify the time‐dependent moisture distribution, the water flux and the water volume infiltrated in the unsaturated zone as a function of soil heterogeneities during a five‐day‐long flooding event. Three methods of estimating the hydraulic parameters of soil in the vadose zone were tested. They are based on the following: (1) experimental data, (2) soil particle‐size distribution and (3) pedology information on soils. Water fluxes calculated from modelling approaches 2 and 3 were compared with those of the experiment‐based values and the effect of these differences on the arrival time and velocity of water at the water table were analysed. Major differences in water fluxes were found among the methods of estimating the hydrodynamic parameters. At the Terrace location, the groundwater recharge predicted using soil data from methods 1 and 2 are approximately 4500 and 2400 mm, respectively. Flow simulations using soil data and the experiment‐based method show the highest velocities of infiltrating water at the soil surface and largest volume of groundwater infiltration but result in the lowest centres of the moisture content mass. The results obtained using soil data based on the pedological method are similar to those calculated using soil parameters based on the particle‐size distribution of extracted soil samples. Water pressure profiles calculated on Terrace and Channel location, 3 and 7 days after the inundation event agreed reasonably well with those observed when using hydrodynamic parameters from the experiment‐based method. However, the flow model using the pedology‐based parameters largely underestimates the time needed to achieve hydrostatic conditions of the soil water profile once water flooding at the soil surface stops. This can be mainly attributed to the low values of estimated van Genuchten parameter α. Copyright © 2012 John Wiley & Sons, Ltd.     

Spatio‐temporal variability of water and energy fluxes – a case study for a mesoscale catchment in pre‐alpine environment

Water and energy fluxes at and between the land surface, the subsurface and the atmosphere are inextricably linked over all spatio‐temporal scales. Our research focuses on the joint analysis of both water and energy fluxes in a pre‐alpine catchment (55 km²) in southern Germany, which is part of the Terrestrial Environmental Observatories (TERENO). We use a novel three‐dimensional, physically based and distributed modelling approach to reproduce both observed streamflow as an integral measure for water fluxes and heat flux and soil temperature measurements at an observation location over a period of 2 years. While heat fluxes are often used for comparison of the simulations of one‐dimensional land surface models, they are rarely used for additional validation of physically based and distributed hydrological modelling approaches. The spatio‐temporal variability of the water and energy balance components and their partitioning for dominant land use types of the study region are investigated. The model shows good performance for simulating daily streamflow (Nash–Sutcliffe efficiency > 0.75). Albeit only streamflow measurements are used for calibration, the simulations of hourly heat fluxes and soil temperatures at the observation site also show a good performance, particularly during summer. A limitation of the model is the simulation of temperature‐driven heat fluxes during winter, when the soil is covered by snow. An analysis of the simulated spatial fields reveals heat flux patterns that reflect the distribution of the land use and soil types of the catchment. The water and energy partitioning is characterized by a strong seasonal cycle and shows clear differences between the selected land use types. Copyright © 2016 The Authors Hydrological Processes Published by John Wiley & Sons Ltd.     

Analysis of incorporating groundwater exchanges in hydrological models

In many catchments, the geographical demarcation does not coincide with the limits of the aquifers, so groundwater may be exchanged beyond their topographic boundaries. By studying groundwater exchanges, the natural resources of a catchment can be better assessed, and the divergences between hydrological models and measurements can be explained. The aim of this work is to reveal the importance of including groundwater exchanges in the hydrological modelling of some catchments, using a water balance model. For this purpose, a simple example is conducted. The so‐called parent model scheme is modified to only allow groundwater exchanges, and it is applied to the headwater of the Segura River Basin District, located in the southeast of Spain. This area is selected because groundwater plays an important role in surface hydrology. The results reveal that groundwater exchanges cannot be neglected in some catchments when assessing water resources because their integration in the hydrological model corrects errors in the water balance. Moreover, this paper proves that water balance models are a useful tool for estimating groundwater exchanges between catchments, which can be contrasted with more complex distributed models or isotopic tracers if there is enough information available. Copyright © 2015 John Wiley & Sons, Ltd.     

Estimating streambed parameters for a disconnected river

Evaluation of stream–aquifer interaction and water balance for a catchment often requires specific information on streambed parameters, such as streambed hydraulic conductivity, seepage flux across the streambed and so on. This paper describes a simple, inexpensive instrument that is used to measure these streambed parameters under the condition of a stream disconnected from groundwater. Our method includes a seepage cylinder for simulation of river water depth. The proposed method was applied to estimate the vertical hydraulic conductivity of a streambed and the changes in vertical seepage rate from stream to groundwater with varied stream water depth in the Manasi River of Xinjiang Uygur Autonomous Region, China. The vertical hydraulic conductivities of the streambed determined from 12 sites along the Manasi River vary from 1.01 to 29.m/day where the stream disconnects from the groundwater. The experimental results suggest that there are two kinds of relations between the vertical seepage rate and the simulated stream water depth. One is a linear relation between the two variables with low Reynolds numbers (less than 10); the other is a nonlinear relation (exponential relation) between the two variables with larger Reynolds numbers (greater than 10). This second relationship is quite different from the traditional model that usually calculates the vertical seepage rate from stream to groundwater under the condition of disconnection using a linear relation (Darcy's Law). Our results suggest that a linear relation can only be used for a limited range of river water depth. This method gives a convenient tool for rapidly estimating the streambed hydraulic conductivity and the changes in the vertical seepage rate across streambed with varied stream water depths for the case of a stream disconnected from groundwater. Copyright © 2013 John Wiley & Sons, Ltd.     

Influence of a rock glacier spring on the stream energy budget and cold‐water refuge in an alpine stream

The thermal regimes of alpine streams remain understudied and have important implications for cold‐water fish habitat, which is expected to decline due to climatic warming. Previous research has focused on the effects of distributed energy fluxes and meltwater from snowpacks and glaciers on the temperature of mountain streams. This study presents the effects of the groundwater spring discharge from an inactive rock glacier containing little ground ice on the temperature of an alpine stream. Rock glaciers are coarse blocky landforms that are ubiquitous in alpine environments and typically exhibit low groundwater discharge temperatures and resilience to climatic warming. Water temperature data indicate that the rock glacier spring cools the stream by an average of 3 °C during July and August and reduces maximum daily temperatures by an average of 5 °C during the peak temperature period of the first two weeks in August, producing a cold‐water refuge downstream of the spring. The distributed stream surface and streambed energy fluxes are calculated for the reach along the toe of the rock glacier, and solar radiation dominates the distributed stream energy budget. The lateral advective heat flux generated by the rock glacier spring is compared to the distributed energy fluxes over the study reach, and the spring advective heat flux is the dominant control on stream temperature at the reach scale. This study highlights the potential for coarse blocky landforms to generate climatically resilient cold‐water refuges in alpine streams.     

Variability and comparison of hyporheic water temperatures and seepage fluxes in a small Atlantic salmon stream

Ground water discharge is often a significant factor in the quality of fish spawning and rearing habitat and for highly biologically productive streams. In the present study, water temperatures (stream and hyporheic) and seepage fluxes were used to characterize shallow ground water discharge and recharge within thestreambed of Catamaran Brook, a small Atlantic salmon (Salmo salar) stream in central New Brunswick, Canada. Three study sites were instrumented using a total of 10 temperature sensors and 18 seepage meters. Highly variable mean seepage fluxes, ranging from 1.7 x 10(-4) to 2.5 cm3 m(-2) sec(-1), and mean hyporheic water temperatures, ranging from 10.5 degrees to 18.0 degrees C, at depths of 20 to 30 cm in the streambed were dependent on streambed location (left versus right stream bank and site location) and time during the summer sampling season. Temperature data were usefulfor determining if an area of the streambed was under discharge (positive flux), recharge (negative flux), or parallel flow (no flux) conditions and seepage meters were used to directly measure the quantity of water flux. Hyporheic water temperature measurements and specific conductance measurements of the seepage meter sample water, mean values ranging from 68.8 to 157.9 microS/cm, provided additional data for determining flux sources. Three stream banks were consistently under discharge conditions, while the other three stream banks showed reversal from discharge to recharge conditions over the sampling season. Results indicate that the majority of the water collected in the seepage meters was composed of surface water. The data obtained suggests that even though a positive seepage flux is often interpreted as ground water discharge, this discharging water may be of stream water origin that has recently entered the hyporheic zone.The measurement of seepage flux in conjunction with hyporheic water temperature or other indicators of water origin should be considered when attempting to quantify the magnitude of exchange and the source of hyporheic water.