Chute channel dynamics in large,sand‐bed meandering rivers

Meander bends of many large, sand‐bed meandering rivers are partitioned by chute channels that convey permanent flow, and co‐exist with the mainstem for decades. As a first step toward understanding the dynamics and morphodynamic implications of these ‘bifurcate meander bends’, this study applied binary logistic regression analysis to determine whether it is possible to predict chute initiation based on attributes of meander bend character and dynamics. Regression models developed for the Strickland River, Papua New Guinea, the lower Paraguay River, Paraguay/Argentina, and the Beni River, Bolivia, revealed that the probability of chute initiation at a meander bend is a function of the bend extension rate (the rate at which a bend elongates in a direction perpendicular to the valley axis trend). Image analyses of all rivers and field observations from the Strickland suggest that the majority of chute channels form during scroll–slough development. Rapid extension is shown to favour chute initiation by breaking the continuity of point bar deposition and vegetation encroachment at the inner bank, resulting in widely‐spaced scrolls with intervening sloughs that are positively aligned with primary over‐bar flow. The rivers plot in order of increasing chute activity on an empirical meandering‐braided pattern continuum defined by potential specific stream power (ω_pv) and bedload calibre (D₅₀). Increasing stream power is considered to result in higher bend extension rates, with implications for chute initiation. In addition, chute stability is shown to depend on river sediment load relative to flow discharge (Qs/Q), such that while the Beni may plot in the region of highly braided rivers by virtue of a high potential specific stream power, the formation of stable chute channels is suppressed by the high sediment load. This tendency is consistent with previous experimental studies, and results in a planform that is transitional between single‐thread meandering and braided. Copyright © 2011 John Wiley & Sons, Ltd.     

EXPERIMENTAL STUDY ON THE RELATION OF BED MORPHOLOGY WITH SURFACE FLOW IN MEANDER CHANNELS

1 INTRODUCTION The plane shape of a river channel is very important for river improvement planning, because it must allow floodwater to flow off safely. Natural rivers wind from side to side, which creates meandering forms. From the history of river impro…     

EXPERIMENTAL STUDY ON THE RELATIONA OF BED MORPHOLOGY WITH SURFACE FLOW IN MEANDER CHANNELS

Alternate bars have the property that they migrate downstream whenever floods occur. However, in meander channels whose bend angles are larger than a critical value, the migration of bars can be suppressed, and the positions of bank erosion and flood attack also will be steady. In this study, the bed morphology in flume channels with bends of various lengths and angles is investigated at various flow discharges, and the relation of bed morphology to surface flow is investigated in detail using fluid measuring software. An effort is made to obtain guidelines for the plane shape design of meander channels. Based on the experimental results of bed topography and measurement of surface flow direction and velocity distribution, from the viewpoint of bank erosion and the concentration and dispersion of flood flow the most suitable plane shape for meandering channels is suggested through which the migration of alternate bars is suppressed.     

Bar dynamics and bifurcation evolution in a modelled braided sand‐bed river

Morphodynamics in sand‐bed braided rivers are associated with simultaneous evolution of mid‐channel bars and channels on the braidplain. Bifurcations around mid‐channel bars are key elements that divide discharge and sediment. This, in turn, may control the evolution of connected branches, with effects propagating to both upstream and downstream bifurcations. Recent works on bifurcation stability and development hypothesize major roles of secondary flow and gradient advantage. However, this has not been tested for channel networks within a fully developed dynamic braided river. A reason for this is a lack of detailed measurements with sufficient temporal and spatial length, covering multiple bifurcations. Therefore we used a physics‐based numerical model to generate a dataset of bathymetry, flow and sediment transport of an 80 km river reach with self‐formed braid bars and bifurcations. The study shows that bar dissection due to local transverse water surface gradients is the dominant bifurcation initiation mechanism, although conversion of unit bars into compound bars dominates in the initial stage of a braided river. Several bifurcation closure mechanisms are equally important. Furthermore, the study showed that nodal point relations for bifurcations are unable to predict short‐term bifurcation evolution in a braided river. This is explained by occurrence of nonlinear processes and non‐uniformity within the branches, in particular migrating bars and larger‐scale backwater‐effects, which are not included in the nodal point relations. Planform morphology, on the other hand, has predictive capacity: bifurcation angle asymmetry and bar‐tail limb shape are indicators for near‐future bifurcation evolution. Remote sensing data has predictive value, for which we developed a conceptual model for interactions between bars, bifurcations and channels in the network. We conducted a preliminary test of the conceptual model on satellite images of the Brahmaputra. Copyright © 2015 John Wiley & Sons, Ltd.     

A field test of tubino's (1991) model of alternate bar formation

This study investigates the fluvial dynamics of straight natural stream channels. In particular, this experimental field study quantitatively assesses a physically based non-linear mathematical theory of alternate bar formation under unsteady natural flow conditions within a straight alluvial stream. The study site is an artificially straightened section of the Embarras River located approximately 16 km south of Champaign, Illinois. Data were collected on channel form, gradient, alternate bar dimensions, bed sediment size and flow stage over a 2 year study period. Both linear and non-linear steady flow hydrodynamic theories suggest that alternate bars are critical to the process of meander development. But these theories do not predict bar development for unsteady flow conditions, which typically occur in natural alluvial channels. Tubino (1991) suggests that bar evolution for a flood hydrograph can be divided into three parts: (1) a period of limited bar growth during the rising stage of the flood; (2) a stage of modest bar decay near the peak of the flood; and (3) a stage of non-linear bar growth during the prolonged falling stage of the flood. Bars developed during the falling limb of a hydrograph, and exhibited sequential development rather than the uniform growth along the reach predicted by Tubino's model. As flow stage decreased, short, low, fine-grained bars were superimposed on long, high and coarser-grained bars that developed under preceding high flow stages. These results suggest that the process of bar formation in artificially straightened natural streams with heterogeneous bed material may occur under different flow conditions and in a different manner than predicted by theoretical models. Further work should focus on attempting to isolate the physical mechanisms responsible for alternate bar formation in straight natural streams with heterogeneous bed material and flashy hydrologic flow regimes.     

Influence of junction angle on three‐dimensional flow structure and bed morphology at confluent meander bends during different hydrological conditions

Recent field and modeling investigations have examined the fluvial dynamics of confluent meander bends where a straight tributary channel enters a meandering river at the apex of a bend with a 90° junction angle. Past work on confluences with asymmetrical and symmetrical planforms has shown that the angle of tributary entry has a strong influence on mutual deflection of confluent flows and the spatial extent of confluence hydrodynamic and morphodynamic features. This paper examines three‐dimensional flow structure and bed morphology for incoming flows with high and low momentum‐flux ratios at two large, natural confluent meander bends that have different tributary entry angles. At the high‐angle (90°) confluent meander bend, mutual deflection of converging flows abruptly turns fluid from the lateral tributary into the downstream channel and flow in the main river is deflected away from the outer bank of the bend by a bar that extends downstream of the junction corner along the inner bank of the tributary. Two counter‐rotating helical cells inherited from upstream flow curvature flank the mixing interface, which overlies a central pool. A large influx of sediment to the confluence from a meander cutoff immediately upstream has produced substantial morphologic change during large, tributary‐dominant discharge events, resulting in displacement of the pool inward and substantial erosion of the point bar in the main channel. In contrast, flow deflection is less pronounced at the low‐angle (36°) confluent meander bend, where the converging flows are nearly parallel to one another upon entering the confluence. A large helical cell imparted from upstream flow curvature in the main river occupies most of the downstream channel for prevailing low momentum‐flux ratio conditions and a weak counter‐rotating cell forms during infrequent tributary‐dominant flow events. Bed morphology remains relatively stable and does not exhibit extensive scour that often occurs at confluences with concordant beds. Copyright © 2014 John Wiley & Sons, Ltd.     

Intra‐event scale bar–bank interactions and their role in channel widening

Channel bars and banks strongly affect the morphology of both braided and meandering rivers. Accordingly, bar formation and bank erosion processes have been greatly explored. There is, however, a lack of investigations addressing the interactions between bed and bank morphodynamics, especially over short timescales. One major implication of this gap is that the processes leading to the repeated accretion of mid‐channel bars and associated widenings remain unsolved. In a restored section of the Drau River, a gravel‐bed river in Austria, mid‐channel bars have developed in a widening channel. During mean flow conditions, the bars divert the flow towards the banks. One channel section exhibited both an actively retreating bank and an expanding mid‐channel bar, and was selected to investigate the morphodynamic processes involved in bar accretion and channel widening at the intra‐event timescale. We repeatedly surveyed riverbed and riverbank topography, monitored riverbank hydrology and mounted a time‐lapse camera for continuous observation of riverbank erosion processes during four flow events. The mid‐channel bar was shown to accrete when it was submerged during flood events, which at the subsequent flow diversion during lower discharges narrowed the branch along the bank and increased the water surface elevation upstream from the riffle, which constituted the inlet into the branch. These changes of bed topography accelerated the flow along the bank and triggered bank failures up to 20 days after the flood events. Four analysed flow events exhibited a total bar expansion from initially 126 m² to 295 m², while bank retreat was 6 m at the apex of the branch. The results revealed the forcing role of bar accretion in channel widening and highlighted the importance of intra‐event scale bed morphodynamics for bank erosion, which were summarized in a conceptual model of the observed bar–bank interactions. Copyright © 2015 John Wiley & Sons, Ltd.     

Hydraulic parameter estimations of a 2D model validated with sedimentological findings in the point bar environment

There have been a number of flume tests of flow round bends with idealized geometry and recently hydraulic simulations of such experiment. However, studies of hydraulic models in natural river bend are rather limited because of greater complexity of the flow characteristics and lack of detailed data. In this article, we study how 2D hydraulic model and raster‐based hydraulic parameter calculations predict flow characteristics on the natural point bar environment. We will compare calculations of various hydraulic parameters (velocity, bed shear stress and stream power) by the 2D model and the associated sedimentology of the point bars. As a result of comparison, the usability of the 2D model for flow‐form‐product relationship predictions will be evaluated in natural river bend environment. The study shows that the 2D model can be generally utilized to predict the flood‐generated flow‐form‐product relationship in coarse‐grained and structurally complex point bar environments with sand‐dominated bedload. For example, point bar sections submerged in water depths greater than 50 cm showed a relatively good match laterally between the model and sedimentological estimations. Furthermore, this approach allows us to estimate flood processes on a local scale in similar point bar environments with width–length ratio. The flow direction estimates of the 2D model coincided relatively well with the sedimentological estimations on the bar head. However, flow directions on the downstream section could not be modelled because the 2D model cannot handle the helicoidal flow of the river bend. Copyright © 2010 John Wiley & Sons, Ltd.     

Meander hydrodynamics initiated by river restoration deflectors

River restoration projects have installed j‐hook deflectors along the outer bank of meander bends to reduce hydraulic erosion, and in this study we use a computational fluid dynamics (CFD) model to document how these deflectors initiate changes in meander hydrodynamics. We validated the CFD with streamwise and cross‐channel bankfull velocities from a 193° meander bend flume (inlet at 0°) with a fixed point bar and pool equilibrium bed but no j‐hooks, and then used the CFD to simulate changes to flow initiated by bank‐attached boulder j‐hooks (1^st attached at 70°, then a 2^nd at 160°). At bankfull and half bankfull flow the j‐hooks flattened transverse water surface slopes, formed backwater pools upstream of the boulders, and steepened longitudinal water slopes across the boulders and in the conveyance region off the mid‐channel boulder tip. Streamwise velocity and mass transport jets upstream of the j‐hooks were stilled, mid‐channel jets were initiated in the conveyance region, eddies with a cross‐channel axis formed below boulders, and eddies with a vertical axis were shed into wake zones downstream of the point bar and outer bank boulders. At half bankfull depth conveyance region flow cut toward the outer bank downstream of the j‐hook boulders and the secondary circulation cells were reshaped. At bankfull depth the j‐hook at 160° was needed to redirect bank‐impinging flow sent by the upstream j‐hook. The hooked boulder tip of both j‐hooks funneled surface flow into mid‐channel plunging jets, which reversed the secondary circulation cells and initiated 1 to 3 counter rotating cells through the entire meander. The main outer bank collision zone centered at 50° without the j‐hook was moved by the j‐hook to within and just beyond the 70° j‐hook boulder region, which displaced other mass transport zones downstream. J‐hooks re‐organized water surface slopes, streamwise and cross‐channel velocities, and mass transport patterns, to move shear stress from the outer bank and into the conveyance and mid‐channel zones at bankfull flow. At half bankfull flows a patch of high shear re‐attached to the outer bank below the downstream j‐hook. J‐hook geometry and placement within natural meanders can be analyzed with CFD models to help restoration teams reach design goals and understand hydraulic impacts. Copyright © 2011 John Wiley & Sons, Ltd.     

Tidal channel meander formation by depositional rather than erosional processes: examples from the prograding Skagit River Delta (Washington,USA)

Channel meander dynamics in fluvial systems and many tidal systems result from erosion of concave banks coupled with sediment deposition on convex bars. However, geographic information system (GIS) analysis of historical aerial photographs of the Skagit Delta marshes provides examples of an alternative meander forming process in a rapidly prograding river delta: deposition‐dominated tidal channel meander formation through a developmental sequence beginning with sandbar formation at the confluence of a blind tidal channel and delta distributary, proceeding to sandbar colonization and stabilization by marsh vegetation to form a marsh island opposite the blind tidal channel outlet, followed by narrowing of the gap between the island and mainland marsh, closure of one half of the gap to join the marsh island to the mainland, and formation of an approximately right‐angle blind tidal channel meander bend in the remaining half of the gap. Topographic signatures analogous to fluvial meander scroll bars accompany these planform changes. Parallel sequences of marsh ridges and swales indicate locations of historical distributary shoreline levees adjacent to filled former island/mainland gaps. Additionally, the location of marsh islands within delta distributaries is not random; islands are disproportionately associated with blind tidal channel/distributary confluences. Furthermore, blind tidal channel outlet width is positively correlated with the size of the marsh island that forms at the outlet, and the time until island fusion with mainland marsh. These observations suggest confluence hydrodynamics favor sandbar/marsh island development. The transition from confluence sandbar to tidal channel meander can take as little as 10 years, but more typically occurs over several decades. This depositional blind tidal channel meander formation process is part of a larger scale systemic depositional process of delta progradation that includes distributary elongation, gradient reduction, flow‐switching, shoaling, and narrowing. Copyright © 2010 John Wiley & Sons, Ltd.     

Two‐dimensional and three‐dimensional computational models in hydrodynamic and morphodynamic reconstructions of a river bend: sensitivity and functionality

This study assesses hydrodynamic and morphodynamic model sensitivity and functionality in a curved channel. The sensitivity of a depth‐averaged model to user‐defined parameters (grain size, roughness, transverse bed slope effect, transport relations and secondary flow) is tested. According to the sensitivity analysis, grain size, transverse bed slope effect and sediment transport relations are critical to simulated meander bend morphodynamics. The parametrization of grain size has the most remarkable effect: field‐based grain size parametrization is necessary in a successful morphodynamic reconstruction of a meander bend. The roughness parametrization method affects the distribution of flow velocities and therefore also morphodynamics. The combined effect of various parameters needs further research. Two‐dimensional (2D) and three‐dimensional (3D) reconstructions of a natural meander bend during a flood event are assessed against field measurements of acoustic Doppler current profiler and multi‐temporal mobile laser scanning data. The depth‐averaged velocities are simulated satisfactorily (differences from acoustic Doppler current profiler velocities 5–14%) in both 2D and 3D simulations, but the advantage of the 3D hydrodynamic model is unquestionable because of its ability to model vertical and near‐bed flows. The measured and modelled near‐bed flow, however, differed notably from each other's, the reason of which was left open for future research. It was challenging to model flow direction beyond the apex. The 3D flow features, which also affected the distribution of the bed shear stress, seem not to have much effect on the predicted morphodynamics: the 2D and 3D morphodynamic reconstructions over the point bar resembled each other closely. Although common features between the modelled and measured morphological changes were also found, some specific changes that occurred were not evident in the simulation results. Our results show that short‐term, sub‐bend scale morphodynamic processes of a natural meander bend are challenging to model, which implies that they are affected by factors that have been neglected in the simulations. The modelling of short‐term morphodynamics in natural curved channel is a challenge that requires further study. Copyright © 2014 John Wiley & Sons, Ltd.     

Flow fields in tightly curving meander bends of low width‐depth ratio

Upland swamp channels with low width/depth ratios (w/d), armoured beds, minimal sediment loads, tightly curving bends and an absence of point bars provide a striking contrast to the flow characteristics of larger channels with higher w/d ratios. Two subsets of these bends were examined in relation to their patterns of cross‐stream flow relative to the channel boundary. The first, with mean w/d = 2·0 and gentle barforms, exhibited even velocity distributions at bend entrances but developed vertically stacked pairs of maximum velocity filaments (MVFs). Cross‐stream circulation increased with decreasing curvature before essentially ceasing in the tightest bend due to the conservation of angular momentum and reduced vertical velocity differentials; bed friction has more limited influence in narrow deep channels relative to bank friction. In the second subset of bends, with larger w/d (mean 4·8) and much steeper barforms, the MVFs were laterally paired and strongly helical flow was partly driven by the vertical confinement of flow due to large, stable barforms at the bend entrances. In one bend, the velocity profile became inverted immediately past the apex and caused helical flow to abruptly reverse. Point bars in relatively wide bedload channels appear to greatly distort secondary flow patterns. In narrow, deep, sediment‐starved channels, separation zones against the convex and/or the concave bank deliver the flow confinement that would otherwise be provided by point bars or concave‐bank benches. In these channels, separation zones are important for protecting both the channel bed and banks from scour. Three‐dimensional near bankfull flow fields are presented for one bend with a meander pool; inward shifting of the MVF and limited sediment supply are proposed as mechanisms for the development and maintenance of these features. These flow data in narrow and deep peatland channels demonstrate very different flow patterns and morphological characteristics relative to the more commonly studied wide, shallow channels with more abundant sediment. Copyright © 2009 John Wiley & Sons, Ltd.     

Scroll bars are inner bank levees along meandering river bends

Scroll bars across a 65-km stretch of the Trinity River in Texas, USA were studied using LiDAR data as well as with a series of 11 trenches spread out across the survey area. We conclude that scroll bars are levees that are deposited along the inner banks of these meandering river bends. Scroll bar crests were found to have similar elevations to those of outer bank levee crests, implying that they are constructional features that create positive topographic relief above the elevation of the floodplain. Trenches reveal that scroll bars are built from reworked suspended sediment, with common ripple-scale cross stratification, planar laminations and muddy bioturbated layers – characteristics often associated with levee sedimentation in other systems. LiDAR observation of the erosion of scroll bars by bed material transport during flood implies that scroll bar spacing is an imperfect proxy for estimating overall channel migration rates. In addition, interspersed lenses of coarser sediment with dune-scale cross stratification represent the stratigraphic record of these erosional events and suggest that erosion of the channel-ward edge of the scroll bar is not uncommon. Preservation of scroll bars is unlikely, given that they are responsible for an average of only the uppermost 12% of the total inner bank relief. We suggest that misidentification of point bar lateral accretion surfaces as scroll bars is common and can lead to issues with reconstructing channel properties due to systematic differences between point bar and scroll bar planform geometries. © 2019 John Wiley & Sons, Ltd. © 2019 John Wiley & Sons, Ltd.     

Formation of stationary alternate bars in a steep channel with mixed-size sediment: A flume experiment

Alternate bars were formed by sediment transport in a flume with Froude-modelled flow and relative roughness characteristic of gravel-boulder channels with steep slopes. The flume (0.3 m wide × 7.5 m long) was filled with a sand-gravel mixture, which was also fed into the top of the flume at a constant rate under constant discharge. Channel slope was set at 0.03. Initially, coarse particles accumulated on incipient bar heads near one side of the flume and diverted flow and bedload transport across the flume toward a pool scoured against the opposite flume wall downstream. Sorting in the pool directed coarse particles onto the next bar head downstream. Alternate sequences of pools and coarse bar heads were thereby linked down the entire flume by interactions of sediment sorting, flow, and channel morphology. During episodes of bar construction, unsorted bedload invaded interior bar surfaces and was deposited. Persistent deposition of coarse particles on bar heads prevented downstream migration of bars by inhibiting bar-head erosion and bedload transport over bars. Likely factors leading to bar-head stabilization in modelled gravel-bed channels are coarse mixed-size sediment, steep channel gradients, and shallow depths.     

Three‐dimensional flow structure and channel change in an asymmetrical compound meander loop,Embarras River,Illinois

The planform dynamics of meandering rivers produce a complex array of meander forms, including elongated meander loops. Thus far, few studies have examined in detail the flow structure within meander loops and the relation of flow structure to patterns of planform change. This field‐based investigation examines relations between three‐dimensional fluid motion and channel change within an elongated, asymmetrical meander loop containing multiple pool–riffle structures. The downstream velocity field is characterized by a high‐velocity core that shifts slightly outward as flow moves through individual lobes of the loop. For some of the measured flows this core becomes submerged below the water surface downstream of the lobe apexes. Vectors of cross‐stream/vertical velocities indicate that skew‐induced helical motion develops within the pools near lobe apexes and decays over riffles where channel curvature is less pronounced. Maximum rates of bank retreat generally occur near lobe apexes where impingement of the flow on the outer channel bank is greatest. However, maximum rates and loci of bank retreat differ for upstream and downstream lobes of the loop, leading to increasing asymmetry of loop geometry over time—a finding consistent with experimental investigations of loop evolution. Copyright © 2003 John Wiley & Sons, Ltd.     

Flow in a tightly curving meander bend: effects of seasonal changes in aquatic macrophyte cover

The effects of aquatic macrophytes on flow and turbulence were studied in a tightly curving meander bend. Three field measurement campaigns were carried out within a one year period to capture effects of seasonal changes in macrophyte cover. They comprised three‐dimensional velocity measurements and mappings of vegetation cover and bathymetry. Flow accelerates and converges over the run into an axial pool in a jet‐like flow pattern bordered by outer and inner bank flow separation zones. The jet and widening of the cross‐section anticipate helical flow until the second half of the bend, where an asymmetric pool developed. Submerged vegetation at the riffles preserves the jet at much lower discharges during the summer period by concentrating high momentum fluid near the surface. Plants locally modify the velocity and stress patterns, reduce bed shear stresses, create zones of fine sediment accumulation and reinforce the bed and banks with roots and rhizomes. Plant patches colonising the banks and the point bar confine secondary flow cells laterally and affect shape and magnitude of the transverse flow profiles near their edges. The morphology of the bend was very stable over the observation period and neither bank erosion nor pool scouring occurred. However, fine sediments accumulate within vegetation patches and in the recirculation zones while the remaining open areas tend to erode slightly. With the decay of macrophytes in winter, sediment accumulations are mobilised again and the bathymetry levels, supporting cyclic models of morphologic change in vegetated bends. In the second part of the paper, semi‐empirical models for the three predominant flow types were tested and discussed; velocity and stress models of vegetated mixing layers and plane turbulent jets, and Rozovskii's model for the transverse flow in bends. Copyright © 2012 John Wiley & Sons, Ltd.     

Geomorphological effectiveness of floods to rework gravel bars: Insight from hyperscale topography and hydraulic modelling

Bars are key morphological units in river systems, fashioning the sediment regime and bedload transport processes within a reach. Reworking of these features underpins channel adjustment at larger scales, thereby acting as a key determinant of channel stability. Despite their importance to channel evolution, few investigations have acquired spatially continuous data on bar morphology and sediment-size to investigate bar reworking. To this end, four bars along a 10 km reach of a wandering gravel-bed river were surveyed with terrestrial laser scanning (TLS), comparing downstream changes in slope, bed material size and channel planform. Detrended standard deviations (σ_z) were extracted from TLS point clouds and correlated to underlying physically measured median grain-size (D₅₀), across a greater range of σ_z values than have hitherto been reported. The resulting linear regression model was used to create a 1 m resolution median grain-size map. A fusion of airborne LiDAR and optical-empirical bathymetric mapping was used to develop reach-scale digital elevation models (DEMs) for rapid two-dimensional hydraulic modelling using JFlow® software. The ratio of dimensionless shear stress over critical shear stress was calculated for each raster cell to calculate the effectiveness of a range of flood events (2.33–100 year recurrence intervals) to entrain sediment and rework bar units. Results show that multiple bar forming discharges exist, whereby frequent flood flows rework tail and back channel areas, while much larger, less frequent floods are required to mobilise the coarser sediment fraction on bar heads. Valley confinement is shown to exert a primary influence on patterns of bar reworking. Historical aerial photography, hyperscale DEMs and hydraulic modelling are used to explain channel adjustment at the reach scale. The proportion of the bar comprised of more frequently entrained units (tail, back channel, supra-platform) relative to more static units (bar head) exerts a direct influence upon geomorphic sensitivity. © 2018 John Wiley & Sons, Ltd.     

Event-scale floodplain accretion revealed through tree-ring analysis of buried plains cottonwoods,Powder River,MT, USA

Six plains cottonwoods along the axis of a meander were excavated to determine if dendrochronology could identify the year and location of germination and date past overbank sedimentation events. Samples from all excavated trees showed clear anatomical changes associated with burial, including increased vessel size, decreased definition of annual ring boundaries, and decreased ring widths. Some of these burial signatures were created by deposition of only a few centimeters of sediment, and most burial events were detected by multiple samples from the same tree. Four of the trees germinated at or near the upper surfaces of bar deposits, while two germinated within thin overbank deposits draped over bar deposits, indicating that germination is closely associated with bars. Dates and inferred thicknesses of overbank sedimentation events are consistent with repeated topographic surveys and data obtained from cesium-137 (¹³⁷Cs) analyses. However, the record of overbank sedimentation extracted from the trees does not entirely reflect the history of past peak discharges documented by stream gaging, largely because individual trees are progressively less likely to be flooded through time as the river migrates farther away. Germination dates and locations closely track past positions of the river channel. Germination elevations and the elevations of the tops of point bars appear to be decreasing with time as the bend migrates, implying vertical incision by Powder River at a rate of 7.1 ± 4.3 mm/yr. The rate of floodplain growth determined by elevation changes decreases progressively through time, ultimately reaching an apparent plateau after 0.8–1.3 m of vertical accretion. While similar patterns of vertical accretion have previously been interpreted as resulting from decreasing flood probability with increasing floodplain elevation, distance from the channel is also a first-order control on vertical floodplain growth. © 2019 John Wiley & Sons, Ltd.     

Flow recession as a driver of the morpho‐texture of braided streams

Braiding has been widely studied in humid‐temperate climates though rarely in arid environments. Morpho‐texture of braided streams refers to the morphological‐textural organization in a braid‐cell (stream section including bars, anabranches and chutes) that may strongly relate to different processes and hydrological regimes. The objective of this study is to compare the morpho‐texture of braided streams governed by diverse flow recessions in different climates. Measurements were conducted in the wadis Ze'elim and Rahaf, southeast hyper‐arid Israel, in the Mediterranean Barranca‐de‐los‐Pinos, central Spain and in humid‐temperate braided systems, the La‐Bléone River, Haute‐Provence, France and in the Saisera and Cimoliana torrents, northeast Italy. Terrestrial laser scanning was used to produce point clouds and high resolution digital elevation models of the braid‐cells. Wet braid‐cells in humid‐temperate environments were surveyed by a Total Station. Roughness and the upper tail of grain size distributions were derived from the scanned point clouds or from Wolman sampling. We found that anabranches are commonly finer‐grained than the bars in dryland systems and in semi‐arid sandy braided systems, contrary to the humid‐temperate braided systems. In both climates, chutes are similar or coarser‐grained than the bars which they dissect, in accordance with their steeper gradients due to the considerable bar‐anabranch relief. The Saisera's morpho‐texture is similar to that of the dryland braided channels, despite the very humid‐temperate environment in which it is located, due to its short‐lived, ephemeral type hydrograph. Hydrograph shape, specifically the duration of flow recession, typical of a climate but not confined to it, determines the morpho‐texture of braided streams and the textural differentiation between a depositional bar and the adjacent anabranches. The morpho‐texture of chutes and bars results also from local erosional processes affected by local topography, i.e. ungraded longitudinal profiles, and is not solely determined by flow recession. This new morpho‐textural model enables identifying primary depositional and erosional braiding processes. Copyright © 2015 John Wiley & Sons, Ltd.     

Numerical modelling of alternate bar formation,development and sediment sorting in straight channels

A two‐dimensional shallow water hydro‐sediment‐morphodynamic model is applied to investigate alternate bar formation, development and sediment sorting in straight channels. The model is coupled, explicitly incorporating the flow–sediment–bed interactions by using the full mass and momentum conservation equations, which are numerically solved by a well‐balanced version of the finite volume Slope Limiter Centred (SLIC) scheme. The model is first tested against a flume experiment on alternate bars formed over a uniform sediment bed, which clearly exhibits processes of bar formation, migrating and finally approaching an equilibrium state. Then it is applied to another flume experiment on alternate bars due to non‐uniform sediment transport. The computational results are evaluated, with a focus on the longitudinal and vertical sediment sorting. It is argued for the first time that the inconsistent sediment sorting patterns observed in previous studies are determined by different sediment transport conditions, i.e. full versus partial transport. When a condition of full transport is achieved, under which all size fractions are fully mobilized and transported, the longitudinal surface sediment shows a sorting pattern of coarse‐on‐head and fine‐in‐pool, and the vertical substrate sediment exhibits an immobile‐fine‐coarse structure upwards. In contrast, for a partial transport condition, under which only finer fraction participates in the transport process, an opposite longitudinal pattern (i.e. fine‐on‐head and coarse‐in‐pool) and a different vertical structure (i.e. immobile‐coarse‐fine) are observed. Concurrently, numerical experiments with specified conditions show that the critical aspect ratio for the formation of migrating alternate bars is approximately equal to 12. With the increase of the aspect ratio, the bar length grows gradually, while the bar height increases rapidly for moderate values of the aspect ratio and then keeps nearly stable. The bar celerity, however, is weakly sensitive to the variation of this ratio. Copyright © 2016 John Wiley & Sons, Ltd.