Enhanced modeling of latent heat flux from urban surfaces in the Noah/single-layer urban canopy coupled model

The numerical modeling of the impacts of urban buildings in mesoscale meteorological models has gradually improved in recent years. Correctly representing the latent heat flux from urban surfaces is a key issue in urban land-atmosphere coupling studies but is a common weakness in current urban canopy models. Using the surface energy balance data at a height of 140 m from a 325 m meteorological tower in Beijing, we conducted a 1-year continuous off-line simulation by using a coupled land surface model and a single-layer urban canopy model and found that this model has a relatively large systematic error for simulated latent heat flux. To improve the numerical method for modeling latent heat flux from urban surfaces, we combined observational analysis and urban land surface model to derive an oasis effect coefficient for urban green areas; to develop a temporal variation formula for water availability in urban impervious surfaces; and to specify a diurnal profile and the maximum values of anthropogenic latent heat release for four seasons. These results are directly incorporated into the urban land surface model to improve model performance. In addition, this method serves as a reference for studies in other urban areas.     

Intercomparison across scales between remotely-sensed land surface temperature and representative equilibrium temperature from a distributed energy water balance model

Abstract

Quantifying the reliability of distributed hydrological models is an important task in hydrology to understand their ability to estimate energy and water fluxes at the agricultural district scale as well the basin scale for water resources management in drought monitoring and flood forecasting. In this context, the paper presents an intercomparison of simulated representative equilibrium temperature (RET) derived from a distributed energy water balance model and remotely-sensed land surface temperature (LST) at spatial scales from the agricultural field to the river basin. The main objective of the study is to evaluate the use of LST retrieved from operational remote sensing data at different spatial and temporal resolutions for the internal validation of a distributed hydrological model to control its mass balance accuracy as a complementary method to traditional calibration with discharge measurements at control river cross-sections. Modelled and observed LST from different radiometric sensors located on the ground surface, on an aeroplane and a satellite are compared for a maize field in Landriano (Italy), the agricultural district of Barrax (Spain) and the Upper Po River basin (Italy). A good ability of the model in reproducing the observed LST values in terms of mean bias error, root mean square error, relative error and Nash-Sutcliffe index is shown.

Editor Z.W. Kundzewicz; Associate editor D. Gerten     

Sensitivity of model parameterizations for simulated latent heat flux at the snow surface for complex mountain sites

The snowcover energy balance is typically dominated by net radiation and sensible and latent heat fluxes. Validation of the two latter components is rare and often difficult to undertake at complex mountain sites. Latent heat flux, the focus of this paper, is the primary coupling mechanism between the snow surface and the atmosphere. It accounts for the critical exchange of mass (sublimation or condensation), along with the associated snowcover energy loss or gain. Measured and modelled latent heat fluxes at a wind‐exposed and wind‐sheltered site were compared to evaluate variability in model parameters. A well‐tested and well‐validated snowcover energy balance model, Snobal, was selected for this comparison because of previously successful applications of the model at these sites and because of the adjustability of the parameters specific to latent heat transfer within the model. Simulated latent heat flux and snow water equivalent (SWE) were not sensitive to different formulations of the stability profile functions associated with heat transfer calculations. The model parameters of snow surface roughness length and active snow layer thickness were used to improve latent heat flux simulations while retaining accuracy in the simulation of the SWE at an exposed and sheltered study site. Optimal parameters for simulated latent heat flux and SWE were found at the exposed site with a shorter roughness length and thicker active layer, and at the sheltered site with a longer roughness length and thinner active layer. These findings were linked to physical characteristics of the study sites and will allow for adoption into other snow models that use similar parameters. Physical characteristics of wind exposure and cover could also be used to distribute critical parameters in a spatially distributed modelling domain and aid in parameter selection for application to other watersheds where detailed information is not available. Copyright © 2012 John Wiley & Sons, Ltd.     

2010年智利MS8.8级地震前可能的潜热通量异常及其与地表温度变化的关系

本文研究了2010年2月27日智利8.8级地震前后地球表面潜热通量的时空演化过程, 并分析了可能的潜热通量异常及其与地表温度变化的关系.结果表明:(1)此次地震及其强余震前出现了三次明显的潜热通量异常,第一次潜热通量异常出现于主震1个月前,主要分布在震中及其东南陆区,第二次潜热通量异常出现在主震前7天,异常区分布在震中西南的海域,呈北西向分布,指向俯冲带,第三次潜热通量异常出现在强余震前,异常区分布在震中西南的海域及北段俯冲带上;(2)相似于2004年印度尼西亚地震海啸前潜热通量的异常演化特征,潜热通量异常从弧后向俯冲带迁移,此次地震前的潜热通量异常首先出现在弧后火山活动强烈地区,然后迁移到海域俯冲带附近,可能反映了临震前的构造变形过程;(3)当陆区出现潜热通量异常时,同时也可见地表温度异常,但在海域出现潜热通量异常时,却未发现有地表温度异常,这可能是由于海域水的热容量较大,不易出现红外温度异常所致.     

Simulation of evapotranspiration and carbon dioxide flux in the wheat‐maize rotation croplands of the North China Plain using the Simple Biosphere Model

The North China Plain, which is critical for food production in China, is encountering serious water shortage due to heavy agricultural water requirement. The accurate modelling of carbon dioxide flux and evapotranspiration (ET) in croplands is thus essential for yield prediction and water resources management. The land surface model is powerful in simulating energy and carbon dioxide fluxes between land and atmosphere. Some key processes in the Simple Biosphere Model (Version 2, SiB2) were parameterized based on the observations. The simulated fluxes were tested against the eddy covariance flux measurements over two typical winter wheat/maize double cropping fields. A simple diagnostic parameterisation of soil respiration, not included in SiB2, was added and calibrated using the observations to model the carbon budget. The Ball‐Berry stomatal conductance model was calibrated using observed leaf gas exchange rate, showing that the original SiB2 could significantly underpredict the ET in the wheat field. SiB2 significantly underpredicted soil resistance at the Weishan site, leading to overpredict the ET. Overall, there was a close agreement between the simulated and observed latent heat fluxes and net CO₂ exchange using the re‐parameterized SiB2. These findings are important when the model is used for the regional simulation in the North China Plain. Copyright © 2011 John Wiley & Sons, Ltd.     

华南前汛期降水异常与太平洋海表温度异常的关系

利用近50年华南地区站点逐日降水观测资料和全球大气、海洋分析资料,分析了华南前汛期降水异常的变化特征及其与太平洋海温异常的联系.结果表明,近50年来华南前汛期降水总体呈现减少趋势.影响华南前汛期降水异常的太平洋海温异常型是一个类似于ENSO的西太平洋暖池模态,即显著海温异常区域位于西太平洋暖池.西太平洋暖池区域(120°E—180°E,20°S—20°N)前期冬季海温异常同华南前汛期降水存在显著的负相关关系,是具有预报意义的海温关键区.该关键区海温异常影响华南前汛期降水的可能物理过程是:当前期冬季暖池异常偏暖时,菲律宾周围地区对流活动加强,导致Walker环流及东亚太平洋中低纬局地Hadley环流增强;该异常通过影响东亚－太平洋遥相关波列,使前汛期期间西太平洋副高加强西伸,脊线位置偏北,同时副热带西风急流减弱北退.随着Hadley环流上升支的增强,东亚副热带地区下沉运动也增强了,华南地区对流活动受到抑制.而且由于副高的增强,经过其北侧向华南地区的西南水汽输送辐合也减弱了,因此前汛期降水偏少.冷海温年的情形则相反,华南前汛期降水偏多.近50年来华南前汛期降水总体呈现趋势性减少正是由于前冬西太平洋暖池趋势性增暖所致.     

Determination of bare surface soil moisture from combined temporal evolution of land surface temperature and net surface shortwave radiation

Land surface soil moisture (SSM) is an important variable for hydrological, ecological, and meteorological applications. A multi‐linear model has recently been proposed to determine the SSM content from the combined diurnal evolution of both land surface temperature (LST) and net surface shortwave radiation (NSSR) with the parameters TN (the LST mid‐morning rising rate divided by the NSSR rising rate during the same period) and t_d (the time of daily maximum temperature). However, in addition to the problem that all the coefficients of the multi‐linear model depend on the atmospheric conditions, the model also suffers from the problems of the nonlinearity of TN as a function of the SSM content and the uncertainty of determining the t_d from the diurnal evolution of the LST. To address these problems, a modified multi‐linear model was developed using the logarithm of TN and normalizing t_d by the mid‐morning temperature difference instead of using the TN and t_d. Except for the constant term, the coefficients of all other variables in the modified multi‐linear model proved to be independent of the atmospheric conditions. Using the relevant simulation data, results from the modified multi‐linear model show that the SSM content can be determined with a root mean square error (RMSE) of 0.030m³/m³, provided that the constant term is known or estimated day to day. The validation of the model was conducted using the field measurements at the Langfang site in 2008 in China. A higher correlation is achieved (coefficient of determination: R² = 0.624, RMSE = 0.107m³/m³) between the measured SSM content and the SSM content estimated using the modified multi‐linear model with the coefficients determined from the simulation data. Another experiment is also conducted to estimate the SSM content using the modified model with the constant term calibrated each day by one‐spot measurements at the site. The estimation result has a relatively larger error (RMSE = 0.125m³/m³). Additionally, the uncertainty of the determination of the coefficients is analysed using the field measurements, and the results indicate that the SSM content obtained using the modified model accurately characterizes the surface soil moisture condition. Copyright © 2012 John Wiley & Sons, Ltd.     

Combining the dissipation method and surface renewal analysis to estimate scalar fluxes from the time traces over rangeland grass near Ione (California)

The dissipation method, the method preferred for estimating scalar surface fluxes over open water has not traditionally been used by agronomists, whereas the surface renewal (SR) theory in conjunction with the analysis of the scalar time trace offers tremendous advantages for estimating fluxes over agronomic crops. For a steady and horizontally homogeneous flow, it is shown that the dissipation method and SR analysis are closely related. As a consequence, a new dissipation–SR analysis expression for estimating scalar surface fluxes was derived. The new equation requires no calibration, and the scalar time trace measured at a frequency capable of identifying canopy‐scale coherent structures (typically 4–10 Hz in agriculture) is the only input required. Sensible and latent heat flux estimates obtained from 10 Hz air temperature and water vapour concentration measurements in the inertial sub‐layer (2 m height) over short, homogeneous rangeland grass at a site where similarity does not hold gave similar results to those measured with the eddy covariance (EC) method. For unstable cases, the new equation provided a root mean square error of 57 W m^?2 for the surface energy‐balance closure. For stable cases, the performance was difficult to evaluate because the EC fluxes were similar in magnitude to the sensor error. It is concluded that the proposed method can contribute to a better understanding of hydrological processes and water requirements by providing an accurate, less costly, alternative method to indirectly estimate evapotranspiration as the residual of the energy balance equation. Copyright © 2009 John Wiley & Sons, Ltd.     

Synchronous retrieval of land surface temperature and emissivity

This is an old topic for more than ten years to retrieve land surface temperature (LST) from satellite data, but it has not been solved yet. At first, people tried to transplant traditional split window method of sea surface temperature (SST) to the retrieval of LST, but it was found that the emissivities of land surface (ε_i) must be involved in atmospheric correction. Then many different formulas appeared with assumption of emissivities known. In fact, emissivities of land surface with pixel size cannot be known beforehand because of various reasons, so in recent years the focus of attention has been transferred to retrieving emissivities (ε_i) and LST at the same time. Therefore, we have to solve missing equations problem. For this some people try to introduce middle infrared information, but new problems will be brought in which means that it is very difficult to describe middle infrared BRDF of targets with high accuracy and the scattering of atmospheric aerosol cannot be ignored. Therefore a different way is offered to solve this problem only using two thermo-infrared bands data based on three assumptions, constant emissivities in two measurements, and the same atmospheric parameters for neighbouring pixels and the difference of emissivity (Δε) of two channels can be known beforehand. Results of digital simulations show that it is possible to retrieve LST with its root mean square (RMS) of errors less than 1 K and RMS of relative error of ground radiance at 7% if the error of atmospheric temperature at ± 2°C and the relative error of atmospheric water vapor at ± 10% can be satisfied. Results have been confirmed by initial field test. Project supported by the National Natural Science Foundation of China (Grant No. 49471056) and China’s National Key Basic Research Plan.     

Estimation of spatially distributed surface energy fluxes using remotely‐sensed data for agricultural fields

Land surface energy fluxes are required in many environmental studies, including hydrology, agronomy and meteorology. Surface energy balance models simulate microscale energy exchange processes between the ground surface and the atmospheric layer near ground level. Spatial variability of energy fluxes limits point measurements to be used for larger areas. Remote sensing provides the basis for spatial mapping of energy fluxes. Remote‐sensing‐based surface energy flux‐mapping was conducted using seven Landsat images from 1997 to 2002 at four contiguous crop fields located in Polk County, northwestern Minnesota. Spatially distributed surface energy fluxes were estimated and mapped at 30 m pixel level from Landsat Thematic Mapper and Enhanced Thematic Mapper images and weather information. Net radiation was determined using the surface energy balance algorithm for land (SEBAL) procedure. Applying the two‐source energy balance (TSEB) model, the surface temperature and the latent and sensible heat fluxes were partitioned into vegetation and soil components and estimated at the pixel level. Yield data for wheat and soybean from 1997 to 2002 were mapped and compared with latent heat (evapotranspiration) for four of the fields at pixel level. The spatial distribution and the relation of latent heat flux and Bowen ratio (ratio of sensible heat to latent heat) to crop yield were studied. The root‐mean‐square error and the mean absolute percentage of error between the observed and predicted energy fluxes were between 7 and 22 W m⁻² and 12 and 24% respectively. Results show that latent heat flux and Bowen ratio were correlated (positive and negative) to the yield data. Wheat and soybean yields were predicted using latent heat flux with mean R² = 0·67 and 0·70 respectively, average residual means of −4·2 bushels/acre and 0·11 bushels/acre respectively, and average residual standard deviations of 16·2 bushels/acre and 16·6 bushels/acre respectively (1 bushel/acre ≈ 0·087 m³ ha⁻¹). The flux estimation procedure from the SEBAL‐TSEB model was useful and applicable to agricultural fields. Copyright © 2005 John Wiley & Sons, Ltd.     

A temperature prediction-correction method for estimating surface soil heat flux from soil temperature and moisture data

Surface soil heat flux is a component of surface energy budget and its estimation is needed in land-atmosphere interaction studies. This paper develops a new simple method to estimate soil heat flux from soil temperature and moisture observations. It gives soil temperature profile with the thermal diffusion equation and, then, adjusts the temperature profile with differences between observed and computed soil temperatures. The soil flux is obtained through integrating the soil temperature profile. Compared with previous methods, the new method does not require accurate thermal conductivity. Case studies based on observations, synthetic data, and sensitivity analyses show that the new method is preferable and the results obtained with it are not sensitive to the availability of temperature data in the topsoil. In addition, we pointed out that the soil heat flux measured with a heat-plate can be quite erroneous in magnitude though its phase is accurate.     

Effect of temporal resolution of water level and temperature inputs on numerical simulation of groundwater–surface water flux exchange in a heavily modified urban river

Groundwater interacts with surface water features nearly in all types of landscapes. Understanding these interactions has practical consequences on the quantity and quality of water in either system, because the depletion or contamination of one of the systems will eventually affect the other one. Many studies have shown that the use of heat as natural tracer in conjunction with water level measurements is an effective method for estimating water flow (fluxes) between groundwater and surface water. A number of studies have explored the effects of spatial and temporal variability of groundwater–surface water flux exchanges using temperature and water level measurements; however, the effect of temporal resolution of water level and temperature data on estimating flux remains unexplored. Therefore, this study investigated the effect of temporal resolution of input data on temporal variation of groundwater–surface water flux exchanges. To this end, we calibrated a variably saturated two‐dimensional groundwater flow and heat transport model (VS2DH) at hourly and daily time scales using temperatures measured at multiple depths below the riverbed of the Zenne River, located at a well‐known Belgian brownfield site. Results of the study showed that the computed water flux through the streambed ranged between ?32 mm/day and +25 mm/day using the hourly model and from ?10 mm/day to ?37 mm/day using the daily model. The hourly model resulted in detecting reversal of flow direction inducing short‐term surface water flow into the streambed. However, such events were not captured if daily temperature and water level measurements were used as input. These findings have important implications for understanding contaminant mass flux and their attenuation in the mixing zone of groundwater and surface water. Copyright © 2012 John Wiley & Sons, Ltd.     

近地层能量闭合度对陆面过程模式影响

大量近地层观测试验表明,利用涡动相关法观测的湍流通量小于近地层可利用能量,即近地层能量是不闭合的,这种不闭合度一般为20%甚至更高.而陆面过程模式是基于地气间能量平衡建立,并且模式中的湍流边界层参数化方案通常根据实际观测的湍流通量来确定,因此能量不闭合必将对陆面过程模式造成一定的影响.本文利用2007年春季SACOL站的近地层观测资料,依据能量守恒将能量不闭合中的残余能量通过波文比分配到观测的湍流通量中,即修正涡动相关法观测的湍流通量使得近地层能量达到平衡;之后分别利用观测和修正的湍流通量,建立了能量不闭合和闭合情形下的湍流参数化方案,借助陆面过程模式SHAW,通过数值模拟和对比分析方法考察近地层能量闭合度对陆面过程模式的影响.研究结果表明近地层能量闭合对陆面过程模式有显著的影响:在陆面过程数值模拟中,当应用近地层能量不闭合的湍流通量形成的湍流参数化方案时,陆面过程模式会明显高估地表长波辐射及土壤温度;但当应用修正湍流通量使得近地层能量达到闭合形成的湍流参数化方案后,在不改变任何地表土壤物理生化属性的情况下,陆面过程模式能较好地模拟地表长波辐射和土壤温度.     

近地层能量闭合度对陆面过程模式影响

大量近地层观测试验表明,利用涡动相关法观测的湍流通量小于近地层可利用能量,即近地层能量是不闭合的,这种不闭合度一般为20%甚至更高.而陆面过程模式是基于地气间能量平衡建立,并且模式中的湍流边界层参数化方案通常根据实际观测的湍流通量来确定,因此能量不闭合必将对陆面过程模式造成一定的影响.本文利用2007年春季SACOL站的近地层观测资料,依据能量守恒将能量不闭合中的残余能量通过波文比分配到观测的湍流通量中,即修正涡动相关法观测的湍流通量使得近地层能量达到平衡;之后分别利用观测和修正的湍流通量,建立了能量不闭合和闭合情形下的湍流参数化方案,借助陆面过程模式SHAW,通过数值模拟和对比分析方法考察近地层能量闭合度对陆面过程模式的影响.研究结果表明近地层能量闭合对陆面过程模式有显著的影响:在陆面过程数值模拟中,当应用近地层能量不闭合的湍流通量形成的湍流参数化方案时,陆面过程模式会明显高估地表长波辐射及土壤温度;但当应用修正湍流通量使得近地层能量达到闭合形成的湍流参数化方案后,在不改变任何地表土壤物理生化属性的情况下,陆面过程模式能较好地模拟地表长波辐射和土壤温度.     

太湖小时尺度水面蒸发特征及3种模型模拟效果对比

小时尺度水面蒸发可影响水面大气边界层热力和动力结构,分析湖泊小时尺度水面蒸发主要影响因素,选取准确模拟其特征的蒸发模型,将有助于改善流域天气预报和空气质量预报.基于太湖避风港站2012—2013年通量、辐射和气象观测数据,分析太湖小时尺度水面蒸发主要影响因子和3个模型(传统质量传输模型、Granger and Hedstrom经验模型、DYRESM模型)的模拟效果.结果表明:影响太湖小时尺度水面蒸发的主要因子为水气界面水汽压差和风速的乘积,而非净辐射.传统质量传输模型、Granger and Hedstrom经验模型、DYRESM模型模拟值与全年实测值的一致性系数分别为0.92、0.87和0.89,均方根误差分别为28.35、41.58和38.26 W/m~2.传统质量传输模型对太湖小时尺度水面蒸发的日变化和季节动态模拟效果最佳,其夜间模拟相对误差小于3%,除秋季外,其他季节的模拟绝对误差均小于4 W/m~2.Granger and Hedstrom经验模型系统性地高估太湖潜热通量,在大气较为稳定的午后(高估22~32 W/m~2)和冬季(高估72%)高估最为明显,模拟效果最差.DYRESM模型也系统地高估太湖潜热通量,模拟效果居中.考虑水汽交换系数随风速的变化特征将有助于改善传统质量传输模型和DYRESM模型对太湖小时尺度水面蒸发的模拟精度.     

Numerical simulations of land surface physical processes and land-atmosphere interactions over oasis-desert/Gobi region

A land-surface physical process model was coupled with a mesoscale atmospheric model. This cou- pled model was then used to simulate the interactions between land and the atmosphere, including surface temperature, net radiation, sensible heat flux and latent heat flux over a desert/Gobi with an oasis in northwestern semiarid regions in China. Comparisons between observations and simulations were made over the oasis and the desert/Gobi, respectively. Both cold island effect and wet island ef- fect, the so-called oasis effect, were observed and simulated. Lower temperature, higher specific hu- midity and weaker turbulent transfer were present over the oasis than the desert/Gobi. A subsidence occurred over the oasis, leading to a thermally-generated mesoscale circulation.     

陇东黄土高原下垫面不均匀性指标的建立及其对大孔径闪烁仪(LAS)观测感热通量的影响

目前定量研究下垫面不均匀性对大孔径闪烁仪(LAS)、涡动相关仪(ECS)观测感热通量差异的影响还比较少.本文利用黄土高原庆阳观测站2012年6、7月典型晴天两主风向范围E-SE和SW-W的陆面过程数据,在建立了下垫面不均匀性定量化指标的基础上,分析了下垫面不均匀性与地表温度变率的关系及其对LAS、ECS观测感热通量差异的影响.结果表明:庆阳站下垫面不均匀性大小η和地表温度变率г具有很好的相关性,相关系数达到0.566以上,证明了新建立指标的合理性.下垫面不均匀性大小η和LAS、ECS观测的感热通量差异HLAS-HECS具有很好的一致性,相关系数达到0.634.下垫面不均匀性对LAS和ECS的感热通量差异影响显著,下垫面越不均匀LAS和ECS测量的感热通量差异越大.对两主风向分别进行分析,在E-SE风向范围η和HLAS-HECS的相关系数为0.430,HLAS和HEC拟合的线性趋势系数为1.279,在SW-W风向范围η和HLAS-HECS的相关系数为0.680,HLAS和HEC拟合的线性趋势系数为1.297.下垫面不均匀性的影响程度越大,LAS和ECS观测的感热通量差异越大.     

HydroBlocks: a field‐scale resolving land surface model for application over continental extents

Land surface spatial heterogeneity plays a significant role in the water, energy, and carbon cycles over a range of temporal and spatial scales. Until now, the representation of this spatial heterogeneity in land surface models has been limited to over simplistic schemes because of computation and environmental data limitations. This study introduces HydroBlocks – a novel land surface model that represents field‐scale spatial heterogeneity of land surface processes through interacting hydrologic response units (HRUs). HydroBlocks is a coupling between the Noah‐MP land surface model and the Dynamic TOPMODEL hydrologic model. The HRUs are defined by clustering proxies of the drivers of spatial heterogeneity using high‐resolution land data. The clustering mechanism allows for each HRU's results to be mapped out in space, facilitating field‐scale application and validation. The Little Washita watershed in the USA is used to assess HydroBlocks' performance and added benefit from traditional land surface models. A comparison between the semi‐distributed and fully distributed versions of the model suggests that using 1000 HRUs is sufficient to accurately approximate the fully distributed solution. A preliminary evaluation of model performance using available in situ soil moisture observations suggests that HydroBlocks is generally able to reproduce the observed spatial and temporal dynamics of soil moisture. Model performance deficiencies can be primarily attributed to parameter uncertainty. HydroBlocks' ability to explicitly resolve field‐scale spatial heterogeneity while only requiring an increase in computation of one to two orders of magnitude when compared with existing land surface models is encouraging – ensemble field‐scale land surface modelling over continental extents is now possible. Copyright © 2016 John Wiley & Sons, Ltd.     

Spatial variability of the surface energy balance of Lake Kasumigaura and implications for flux measurements

ABSTRACT

The spatial variability of the lake surface energy balance and its causes are not well-understood. Energy balance maps (90 m resolution) of Lake Kasumigaura (172 km²), Japan, obtained by interpolating station data and bulk equations, allowed an investigation of these issues. Due to lake-scale variations in meteorological variables and small-scale fluctuations of surface temperature, T_s, surface heat fluxes differed horizontally at two distinct scales, while radiative fluxes were more uniform. As the key variable to surface flux T_s was only homogeneous for directions with a longer fetch or under calm wind conditions. Using these findings, the suitability of two flux station locations, one at the centre of the lake and another within a cove, was considered. Although both locations satisfied the fetch requirements, T_s was not always found to be homogeneous in the cove, making this location less suitable for flux measurements, an issue that, to date, has been overlooked.