Experimental analysis of cross‐sectional flow motion in a large amplitude meandering bend

Flow in meandering bends is characterized by the formation of a large cross‐sectional central‐region circulation cell. The width‐to‐depth ratio is one of the most important parameters affecting the entity of the cross‐circulation motion. In steep outside bends, beside the central‐region cell, a counter‐rotating circulation cell often forms in the upper part of the outer‐bank. In spite of its practical importance, the evolving mechanisms of both the circulation cells and their role on boundary shear stress distribution in bends are not yet fully understood. The aim of the present paper is to gain some insight into how cross‐sectional flow motion evolves along meandering bends. Experiments have been carried out in a laboratory meandering channel of large amplitude, over a deformed‐rigid bed, for two values of the width‐to‐depth ratio. The three‐dimensional flow velocity field has been measured in detail at five cross‐sections, almost equally spaced along the channel reach between two consecutive apex sections. The measurements have been carried out on a fine grid by an acoustic Doppler velocity profiler. The distributions of the cross‐sectional flow (e.g. cross‐sectional flow velocity, net transversal flux) and turbulent kinetic energy are analyzed in each investigated section. Measurements show that the counter‐rotating circulation cell is evident only in the case of ‘small’ width‐to‐depth ratio. Such circulation cell begins at the bend entrance and it is fully developed at the bend apex; then it decays. At the bend apex, the core of maximum velocity is found near the bed at about the separation between the central and the outer‐bank circulation cells. Moreover, the presence of the counter‐rotating circulation cell allows the bank shear stress to maintain low values in the outer‐side of the bend. Copyright © 2010 John Wiley & Sons, Ltd.     

Three‐dimensional flow structure and patterns of bed shear stress in an evolving compound meander bend

Compound meander bends with multiple lobes of maximum curvature are common in actively evolving lowland rivers. Interaction among spatial patterns of mean flow, turbulence, bed morphology, bank failures and channel migration in compound bends is poorly understood. In this paper, acoustic Doppler current profiler (ADCP) measurements of the three‐dimensional (3D) flow velocities in a compound bend are examined to evaluate the influence of channel curvature and hydrologic variability on the structure of flow within the bend. Flow structure at various flow stages is related to changes in bed morphology over the study timeframe. Increases in local curvature within the upstream lobe of the bend reduce outer bank velocities at morphologically significant flows, creating a region that protects the bank from high momentum flow and high bed shear stresses. The dimensionless radius of curvature in the upstream lobe is one‐third less than that of the downstream lobe, with average bank erosion rates less than half of the erosion rates for the downstream lobe. Higher bank erosion rates within the downstream lobe correspond to the shift in a core of high velocity and bed shear stresses toward the outer bank as flow moves through the two lobes. These erosion patterns provide a mechanism for continued migration of the downstream lobe in the near future. Bed material size distributions within the bend correspond to spatial patterns of bed shear stress magnitudes, indicating that bed material sorting within the bend is governed by bed shear stress. Results suggest that patterns of flow, sediment entrainment, and planform evolution in compound meander bends are more complex than in simple meander bends. Moreover, interactions among local influences on the flow, such as woody debris, local topographic steering, and locally high curvature, tend to cause compound bends to evolve toward increasing planform complexity over time rather than stable configurations. Copyright © 2016 John Wiley & Sons, Ltd.     

Flow in a tightly curving meander bend: effects of seasonal changes in aquatic macrophyte cover

The effects of aquatic macrophytes on flow and turbulence were studied in a tightly curving meander bend. Three field measurement campaigns were carried out within a one year period to capture effects of seasonal changes in macrophyte cover. They comprised three‐dimensional velocity measurements and mappings of vegetation cover and bathymetry. Flow accelerates and converges over the run into an axial pool in a jet‐like flow pattern bordered by outer and inner bank flow separation zones. The jet and widening of the cross‐section anticipate helical flow until the second half of the bend, where an asymmetric pool developed. Submerged vegetation at the riffles preserves the jet at much lower discharges during the summer period by concentrating high momentum fluid near the surface. Plants locally modify the velocity and stress patterns, reduce bed shear stresses, create zones of fine sediment accumulation and reinforce the bed and banks with roots and rhizomes. Plant patches colonising the banks and the point bar confine secondary flow cells laterally and affect shape and magnitude of the transverse flow profiles near their edges. The morphology of the bend was very stable over the observation period and neither bank erosion nor pool scouring occurred. However, fine sediments accumulate within vegetation patches and in the recirculation zones while the remaining open areas tend to erode slightly. With the decay of macrophytes in winter, sediment accumulations are mobilised again and the bathymetry levels, supporting cyclic models of morphologic change in vegetated bends. In the second part of the paper, semi‐empirical models for the three predominant flow types were tested and discussed; velocity and stress models of vegetated mixing layers and plane turbulent jets, and Rozovskii's model for the transverse flow in bends. Copyright © 2012 John Wiley & Sons, Ltd.     

Reduction of bend scour with an air-bubble screen-morphology and flow patterns

The interplay between streamwise flow,curvature-induced secondary flow,sediment transport and bed morphology leads to the formation of a typical bar-pool bed morphology in open-channel bends.The associated scour at the outer bank and deposition at the inner bank may endanger the outer bank’s stability or reduce the navigable width of the channel.Previous preliminary laboratory experiments in a sharply curved flume with a fixed horizontal bed have shown that a bubble screen located near the outer bank can generate an additional secondary flow located between the outer bank and the curvature-induced secondary flow and with a sense of rotation opposite to the latter.This bubble-induced secondary flow redistributes velocities and bed shear stresses.The reported study investigates the implications of a bubble screen on the flow and the morphology in configurations with mobile bed.Velocity measurements show that the bubble-induced secondary flow shifts the curvature-induced secondary flow in inwards direction and reduces its strength.The bubble screen considerably reduces morphological gradients.Maximum bend scour is reduced by about 50%and occurs further away from the outer bank where it does not endanger the bank stability anymore.The location of maximum scour coincides with the junction of the curvature-induced and bubble-induced secondary flows.At this same location,the maximum streamwise velocities and maximum vertical velocities impinging on the bed also occur,which indicates their importance with respect to the formation of bend scour.The bubble screen also substantially reduced deposition at the inner bank.These preliminary experiments show the potential of a bubble screen to influence and modify the bed morphology.     

Flow fields in tightly curving meander bends of low width‐depth ratio

Upland swamp channels with low width/depth ratios (w/d), armoured beds, minimal sediment loads, tightly curving bends and an absence of point bars provide a striking contrast to the flow characteristics of larger channels with higher w/d ratios. Two subsets of these bends were examined in relation to their patterns of cross‐stream flow relative to the channel boundary. The first, with mean w/d = 2·0 and gentle barforms, exhibited even velocity distributions at bend entrances but developed vertically stacked pairs of maximum velocity filaments (MVFs). Cross‐stream circulation increased with decreasing curvature before essentially ceasing in the tightest bend due to the conservation of angular momentum and reduced vertical velocity differentials; bed friction has more limited influence in narrow deep channels relative to bank friction. In the second subset of bends, with larger w/d (mean 4·8) and much steeper barforms, the MVFs were laterally paired and strongly helical flow was partly driven by the vertical confinement of flow due to large, stable barforms at the bend entrances. In one bend, the velocity profile became inverted immediately past the apex and caused helical flow to abruptly reverse. Point bars in relatively wide bedload channels appear to greatly distort secondary flow patterns. In narrow, deep, sediment‐starved channels, separation zones against the convex and/or the concave bank deliver the flow confinement that would otherwise be provided by point bars or concave‐bank benches. In these channels, separation zones are important for protecting both the channel bed and banks from scour. Three‐dimensional near bankfull flow fields are presented for one bend with a meander pool; inward shifting of the MVF and limited sediment supply are proposed as mechanisms for the development and maintenance of these features. These flow data in narrow and deep peatland channels demonstrate very different flow patterns and morphological characteristics relative to the more commonly studied wide, shallow channels with more abundant sediment. Copyright © 2009 John Wiley & Sons, Ltd.     

Spatial variability of three‐dimensional Reynolds stresses in a developing channel bend

Experimental results of the mean flow field and turbulence characteristics for flow in a model channel bend with a mobile sand bed are presented. Acoustic Doppler velocimeters (ADVs) were used to measure the three components of instantaneous velocities at multiple cross sections in a 135° channel bend for two separate experiments at different stages of clear water scour conditions. With measurements at multiple cross sections through the bend it was possible to map the changes in both the spatial distribution of the mean velocity field and the three Reynolds shear stresses. Turbulent stresses are known to contribute to sediment transport and the three‐dimensionality inherent to flow in open channel bends presents a useful case for determining specific relations between three‐dimensional turbulence and sediment entrainment and transport. These measurements will also provide the necessary data for validating numerical simulations of turbulent flow and sediment transport. The results show that the magnitude and distribution of three‐dimensional Reynolds stresses increase through the bend, with streamwise‐cross stream and cross stream‐vertical components exceeding the maximum principal Reynolds stress through the bend. The most intriguing observation is that near‐bed maximum positive streamwise‐cross stream Reynolds stress coincides with the leading edge of the outer bank scour hole (or thalweg), while maximum cross stream‐vertical Reynolds stress (in combination with high negative streamwise‐cross stream Reynolds stress near the bend apex) coincides with the leading edge of the inner bank bar. Maximum Reynolds stress and average turbulent kinetic energy appear to be greater and more localized over the scour hole before final equilibrium scour is reached. This suggests that the turbulent energy in the flow is higher while the channel bed is developing, and both lower turbulent energy and a broader distribution of turbulent stresses near the bed are required for cessation of particle mobilization and transport. Copyright © 2010 John Wiley & Sons, Ltd.     

Morphodynamics of a bedrock‐alluvial meander bend that incises as it migrates outward: approximate solution of permanent form

In meandering rivers cut into bedrock, erosion across a channel cross‐section can be strongly asymmetric. At a meander apex, deep undercutting of the outer bank can result in the formation of a hanging cliff (which may drive hillslope failure), whereas the inner bank adjoins a slip‐off slope that connects to the hillslope itself. Here we propose a physically‐based model for predicting channel planform migration and incision, point bar and slip‐off slope formation, bedrock abrasion, the spatial distribution of alluvial cover, and adaptation of channel width in a mixed bedrock‐alluvial channel. We simplify the analysis by considering a numerical model of steady, uniform bend flow satisfying cyclic boundary conditions. Thus in our analysis, ‘sediment supply’, i.e. the total volume of alluvium in the system, is conserved. In our numerical simulations, the migration rate of the outer bank is a specified parameter. Our simulations demonstrate the existence of an approximate state of dynamic equilibrium corresponding to a near‐solution of permanent form in which a bend of constant curvature, width, cross‐sectional shape and alluvial cover distribution migrates diagonally downward at constant speed, leaving a bedrock equivalent of a point bar on the inside of the bend. Channel width is set internally by the processes of migration and incision. We find that equilibrium width increases with increasing sediment supply, but is insensitive to outer bank migration rate. The slope of the bedrock point bar varies inversely with both outer bank migration rate and sediment supply. Although the migration rate of the outer bank is externally imposed here, we discuss a model modification that would allow lateral side‐wall abrasion to be treated in a manner similar to the process of bedrock incision. Copyright © 2016 John Wiley & Sons, Ltd.     

Influence of junction angle on three‐dimensional flow structure and bed morphology at confluent meander bends during different hydrological conditions

Recent field and modeling investigations have examined the fluvial dynamics of confluent meander bends where a straight tributary channel enters a meandering river at the apex of a bend with a 90° junction angle. Past work on confluences with asymmetrical and symmetrical planforms has shown that the angle of tributary entry has a strong influence on mutual deflection of confluent flows and the spatial extent of confluence hydrodynamic and morphodynamic features. This paper examines three‐dimensional flow structure and bed morphology for incoming flows with high and low momentum‐flux ratios at two large, natural confluent meander bends that have different tributary entry angles. At the high‐angle (90°) confluent meander bend, mutual deflection of converging flows abruptly turns fluid from the lateral tributary into the downstream channel and flow in the main river is deflected away from the outer bank of the bend by a bar that extends downstream of the junction corner along the inner bank of the tributary. Two counter‐rotating helical cells inherited from upstream flow curvature flank the mixing interface, which overlies a central pool. A large influx of sediment to the confluence from a meander cutoff immediately upstream has produced substantial morphologic change during large, tributary‐dominant discharge events, resulting in displacement of the pool inward and substantial erosion of the point bar in the main channel. In contrast, flow deflection is less pronounced at the low‐angle (36°) confluent meander bend, where the converging flows are nearly parallel to one another upon entering the confluence. A large helical cell imparted from upstream flow curvature in the main river occupies most of the downstream channel for prevailing low momentum‐flux ratio conditions and a weak counter‐rotating cell forms during infrequent tributary‐dominant flow events. Bed morphology remains relatively stable and does not exhibit extensive scour that often occurs at confluences with concordant beds. Copyright © 2014 John Wiley & Sons, Ltd.     

Chute channel dynamics in large,sand‐bed meandering rivers

Meander bends of many large, sand‐bed meandering rivers are partitioned by chute channels that convey permanent flow, and co‐exist with the mainstem for decades. As a first step toward understanding the dynamics and morphodynamic implications of these ‘bifurcate meander bends’, this study applied binary logistic regression analysis to determine whether it is possible to predict chute initiation based on attributes of meander bend character and dynamics. Regression models developed for the Strickland River, Papua New Guinea, the lower Paraguay River, Paraguay/Argentina, and the Beni River, Bolivia, revealed that the probability of chute initiation at a meander bend is a function of the bend extension rate (the rate at which a bend elongates in a direction perpendicular to the valley axis trend). Image analyses of all rivers and field observations from the Strickland suggest that the majority of chute channels form during scroll–slough development. Rapid extension is shown to favour chute initiation by breaking the continuity of point bar deposition and vegetation encroachment at the inner bank, resulting in widely‐spaced scrolls with intervening sloughs that are positively aligned with primary over‐bar flow. The rivers plot in order of increasing chute activity on an empirical meandering‐braided pattern continuum defined by potential specific stream power (ω_pv) and bedload calibre (D₅₀). Increasing stream power is considered to result in higher bend extension rates, with implications for chute initiation. In addition, chute stability is shown to depend on river sediment load relative to flow discharge (Qs/Q), such that while the Beni may plot in the region of highly braided rivers by virtue of a high potential specific stream power, the formation of stable chute channels is suppressed by the high sediment load. This tendency is consistent with previous experimental studies, and results in a planform that is transitional between single‐thread meandering and braided. Copyright © 2011 John Wiley & Sons, Ltd.     

Intra‐event scale bar–bank interactions and their role in channel widening

Channel bars and banks strongly affect the morphology of both braided and meandering rivers. Accordingly, bar formation and bank erosion processes have been greatly explored. There is, however, a lack of investigations addressing the interactions between bed and bank morphodynamics, especially over short timescales. One major implication of this gap is that the processes leading to the repeated accretion of mid‐channel bars and associated widenings remain unsolved. In a restored section of the Drau River, a gravel‐bed river in Austria, mid‐channel bars have developed in a widening channel. During mean flow conditions, the bars divert the flow towards the banks. One channel section exhibited both an actively retreating bank and an expanding mid‐channel bar, and was selected to investigate the morphodynamic processes involved in bar accretion and channel widening at the intra‐event timescale. We repeatedly surveyed riverbed and riverbank topography, monitored riverbank hydrology and mounted a time‐lapse camera for continuous observation of riverbank erosion processes during four flow events. The mid‐channel bar was shown to accrete when it was submerged during flood events, which at the subsequent flow diversion during lower discharges narrowed the branch along the bank and increased the water surface elevation upstream from the riffle, which constituted the inlet into the branch. These changes of bed topography accelerated the flow along the bank and triggered bank failures up to 20 days after the flood events. Four analysed flow events exhibited a total bar expansion from initially 126 m² to 295 m², while bank retreat was 6 m at the apex of the branch. The results revealed the forcing role of bar accretion in channel widening and highlighted the importance of intra‐event scale bed morphodynamics for bank erosion, which were summarized in a conceptual model of the observed bar–bank interactions. Copyright © 2015 John Wiley & Sons, Ltd.     

Meander hydrodynamics initiated by river restoration deflectors

River restoration projects have installed j‐hook deflectors along the outer bank of meander bends to reduce hydraulic erosion, and in this study we use a computational fluid dynamics (CFD) model to document how these deflectors initiate changes in meander hydrodynamics. We validated the CFD with streamwise and cross‐channel bankfull velocities from a 193° meander bend flume (inlet at 0°) with a fixed point bar and pool equilibrium bed but no j‐hooks, and then used the CFD to simulate changes to flow initiated by bank‐attached boulder j‐hooks (1^st attached at 70°, then a 2^nd at 160°). At bankfull and half bankfull flow the j‐hooks flattened transverse water surface slopes, formed backwater pools upstream of the boulders, and steepened longitudinal water slopes across the boulders and in the conveyance region off the mid‐channel boulder tip. Streamwise velocity and mass transport jets upstream of the j‐hooks were stilled, mid‐channel jets were initiated in the conveyance region, eddies with a cross‐channel axis formed below boulders, and eddies with a vertical axis were shed into wake zones downstream of the point bar and outer bank boulders. At half bankfull depth conveyance region flow cut toward the outer bank downstream of the j‐hook boulders and the secondary circulation cells were reshaped. At bankfull depth the j‐hook at 160° was needed to redirect bank‐impinging flow sent by the upstream j‐hook. The hooked boulder tip of both j‐hooks funneled surface flow into mid‐channel plunging jets, which reversed the secondary circulation cells and initiated 1 to 3 counter rotating cells through the entire meander. The main outer bank collision zone centered at 50° without the j‐hook was moved by the j‐hook to within and just beyond the 70° j‐hook boulder region, which displaced other mass transport zones downstream. J‐hooks re‐organized water surface slopes, streamwise and cross‐channel velocities, and mass transport patterns, to move shear stress from the outer bank and into the conveyance and mid‐channel zones at bankfull flow. At half bankfull flows a patch of high shear re‐attached to the outer bank below the downstream j‐hook. J‐hook geometry and placement within natural meanders can be analyzed with CFD models to help restoration teams reach design goals and understand hydraulic impacts. Copyright © 2011 John Wiley & Sons, Ltd.     

A simple model of river meandering and its comparison to natural channels

We develop a new method for analysis of meandering channels based on planform sinuosity. This analysis objectively identifies three channel‐reach lengths based on sinuosity measured at those lengths: the length of typical, simple bends; the length of long, often compound bends; and the length of several bends in sequence that often evolve from compound bends to form multibend loops. These lengths, when normalized by channel width, tend to fall into distinct and clustered ranges for different natural channels. Mean sinuosity at these lengths also falls into distinct ranges. That range is largest for the third and greatest length, indicating that, for some streams, multibend loops are important for planform sinuosity, whereas for other streams, multibend loops are less important. The role of multibend loops is seldom addressed in the literature, and they are not well predicted by previous modelling efforts. Also neglected by previous modelling efforts is bank–flow interaction and its role in meander evolution. We introduce a simple river meandering model based on topographic steering that has more in common with cellular approaches to channel braiding and landscape evolution modelling than to rigorous, physics‐based analyses of river meandering. The model is sufficient to produce reasonable meandering channel evolution and predicts compound bend and multibend loop formation similar to that observed in nature, in both mechanism and importance for planform sinuosity. In the model, the tendency to form compound bends is sensitive to the relative magnitudes of two lengths governing meander evolution: (i) the distance between the bend cross‐over and the zone of maximum bank shear stress, and (ii) the bank shear stress dissipation length related to bank roughness. In our simple model, the two lengths are independent. This sensitivity implies that the tendency for natural channels to form compound bends may be greater when the banks are smoother. Copyright © 2002 John Wiley & Sons, Ltd.     

Temporal and spatial adjustments of channel migration and planform geometry: responses to ENSO driven climate anomalies on the tropical freely‐meandering Aguapeí River,São Paulo,Brazil

Two reaches of Aguapeí River, a left‐bank tributary of the Paraná River in western São Paulo state, Brazil, were studied with the objective of assessing the role of bend curvature on channel migration in this wet‐tropical system and examining if land‐use changes or ENSO (El Niño Southern Oscillation) driven climate anomalies over nearly half a century have changed migration behaviour and planform geometry. Meander‐bend migration rates and morphometric parameters including meander‐bend curvature, sinuosity, meander wavelength and channel width, were measured and the frequency of bend cutoffs was analysed in order to determine the rate of change of channel adjustment over a 48 year period to 2010. Results show that maximum average channel migration rates occur in bends with curvatures of about 2–3 r_c/w, similar to other previously studied temperate and subarctic freely meandering rivers although not as pronounced and with a tendency to favour tighter curvature. From 1962 to 2010 the Aguapeí River has undergone a significant reduction in sinuosity, a shift from tightly curving to more open bends, an overall decline in channel migration rates, an associated decrease in the frequency of neck‐cutoffs and an overall increase in channel width. As the majority of the drainage basin (96%) was already deforested in 1962, channel form and process changes were, unlike an interpretation for an adjacent river system, not attributed to altered land‐use but rather to a sharp ENSO‐driven increase in the magnitude of peak flow‐discharges of some 32% since 1972. In summary, this research revealed that recent climate and associated flow regime changes are having a pronounced effect on river channel behaviour in the Aguapeí River investigated here. Copyright © 2018 John Wiley & Sons, Ltd.     

Channel morphologic processes of a highly sinuous bend approaching neck cutoff by bank erosion in the middle Yangtze River

The distal reach of the Lower Jingjiang River(LJR)in the middle of the Yangtze River consists of five adjacent bends,among which the Qigongling Bend is a U-shaped meander with a mean sinuosity of 2.2 and the narrowest neck 525 m in width.This bend is slowly approaching neck cutoff owing to progressive bank erosion.An abnormal phenomenon has occurred in this bend since the Three Gorges Reservoir(TGR)began to operate in 2003 which is erosion in the inner bank zone and deposition in the outer bank zone.This problem has not been fully understood because of the interplay of changes in water-sediment,bank erosion,and artificial bank revetment.In this study,aerial and remote sensing images,hydrological data,channel topography,and an existing bank erosion model are used to reveal channel morphodynamics of this bend and the trend of the potential neck cutoff induced by bank erosion.The study results show that the clear water released from the TGR has provided by forcefully eroded the point bar of inner bank but failed to scour the outer bank due to the protection of bank revetment since the 1990 s.Thus far,the outer bank zone near the bend apex has increasingly widened in conjunction with the formation of 2 emerging sand bars.Consequently,the thalweg of the main channel has laterally shifted toward the inner bank by roughly 800 m.More severely,the rate of bank retreat on the upstream side of the bend neck was about 4.5 m/yr in 2010-2019,but the downstream side of this neck was experienced slight deposition.Bank erosion could be accelerated by progressively increasing erosion and eventually trigger the occurrence of neck cutoff in the next few decades,thereby significantly altering the quasi-equilibrium regime of channel morphodynamics in the LJR.     

Persistence of the surface texture of a gravel‐bed river during a large flood

We present herein clear field evidence for the persistence of a coarse surface layer in a gravel‐bed river during flows capable of transporting all grain sizes present on the channel bed. Detailed field measurements of channel topography and bed surface grain size were made in a gravel‐bed reach of the Colorado River prior to a flood in 2003. Runoff produced during the 2003 snowmelt was far above average, resulting in a sustained period of high flow with a peak discharge of 27 m³/s (170% of normal peak flow); all available grain sizes within the study reach were mobilized in this period of time. During the 2003 peak flow, the river avulsed immediately upstream of the study reach, thereby abandoning approximately one half kilometer of the former channel. The abandonment was rapid (probably within a few hours), leaving the bed texture essentially frozen in place at the peak of the flood. All locations sampled prior to the flood were resampled following the stream abandonment. In response to the high flow, the surface median grain size (D_50s) coarsened slightly in the outer part of the bend while remaining nearly constant along the inner part of the bend, resulting in an overall increase from 18 to 21 mm for the study reach. Thus, the coarse bed surface texture persisted despite shear stresses throughout the bend that were well above the critical entrainment value. This may be explained because the response of the bed texture to increases in flow strength depends primarily upon the continued availability of the various grain size percentiles in the supply, which in this case was essentially unlimited for all sizes present in the channel. Copyright © 2007 John Wiley & Sons, Ltd.     

A model of equilibrium bed topography for meander bends with erodible banks

Channel curvature produces secondary currents and a transverse sloping channel bed, along which the depth increases towards the outer bank. As a result deep pools tend to form adjacent to the outer bank, promoting bank collapse. The interaction of sediment grains with the primary and secondary flow and the transverse sloping bed also causes meanders to move different grain sizes in different proportions and directions, resulting in a consistent sorting pattern. Several models have been developed to describe this process, but they all have the potential to over‐predict pool depth because they cannot account for the influence of erodible banks. In reality, bank collapse might lead to the development of a wider, shallower cross‐section and any resulting flow depth discrepancy can bias associated predictions of flow, sediment transport, and grain‐size sorting. While bed topography, sediment transport and grain sorting in bends will partly be controlled by the sedimentary characteristics of the bank materials, the magnitude of this effect has not previously been explored. This paper reports the development of a model of flow, sediment transport, grain‐size sorting, and bed topography for river bends with erodible banks. The model is tested via intercomparison of predicted and observed bed topography in one low‐energy (5·3 W m^?2 specific stream power) and one high‐energy (43·4 W m^?2) study reach, namely the River South Esk in Scotland and Goodwin Creek in Mississippi, respectively. Model predictions of bed topography are found to be satisfactory, at least close to the apices of bends. Finally, the model is used in sensitivity analyses that provide insight into the influence of bank erodibility on equilibrium meander morphology and associated patterns of grain‐size sorting. The sensitivity of meander response to bank cohesion is found to increase as a function of the available stream power within the two study bends. Copyright © 2002 John Wiley & Sons, Ltd.     

The effects of ice cover on flow characteristics in a subarctic meandering river

The effects of ice cover on flow characteristics in meandering rivers are still not completely understood. Here, we quantify the effects of ice cover on flow velocity, the vertical and spatial flow distribution, and helical flow structure. Comparison with open‐channel low flow conditions is performed. An acoustic doppler current profiler (ADCP) is used to measure flow from up to three meander bends, depending on the year, in a small sandy meandering subarctic river (Pulmanki River) during two consecutive ice‐covered winters (2014 and 2015). Under ice, flow velocities and discharges were predominantly slower than during the preceding autumn open‐channel conditions. Velocity distribution was almost opposite to theoretical expectations. Under ice, velocities reduced when entering deeper water downstream of the apex in each meander bend. When entering the next bend, velocities increased again together with the shallower depths. The surface velocities were predominantly greater than bottom/riverbed velocities during open‐channel flow. The situation was the opposite in ice‐covered conditions, and the maximum velocities occurred in the middle layers of the water columns. High‐velocity core (HVC) locations varied under ice between consecutive cross‐sections. Whereas in ice‐free conditions the HVC was located next to the inner bank at the upstream cross‐sections, the HVC moved towards the outer bank around the apex and again followed the thalweg in the downstream cross‐sections. Two stacked counter‐rotating helical flow cells occurred under ice around the apex of symmetric and asymmetric bends: next to the outer bank, top‐ and bottom‐layer flows were towards the opposite direction to the middle layer flow. In the following winter, no clear counter‐rotating helical flow cells occurred due to the shallower depths and frictional disturbance by the ice cover. Most probably the flow depth was a limiting factor for the ice‐covered helical flow circulation, similarly, the shallow depths hinder secondary flow in open‐channel conditions. Copyright © 2016 John Wiley & Sons, Ltd.     

Flow and erosion at a bend in the braided Jamuna River

The braided Jamuna River frequently changes its courses.Sometimes the secondary channel in a braided river acts as a single thread meandering channel.In the present study an attempt has been made to investigate the flow patterns and to estimate the rate of bank erosion in a bend along the Jamuna River.The three dimensional(3D) flow velocities were measured using Acoustic Doppler Current Profiler(ADCP).It is found that the near bank velocity is amplified by 1.1 to 1.3 times as compared with the section averaged velocity.A dominant secondary current is found in the upstream bend.The evolution as well as decay of the secondary current is not as clear as it is found in the laboratory experiments.It is revealed from the analysis of the flow process that the causes of higher rate of erosion at the study bend are the oblique flow near bankline,six times amplified shear velocity than critical shear velocity near bankline and the secondary current which acts as a sediment transporting agent from the outer bank towards the inner bank or the sand bar.Based on the flow processes,a simplified erosion prediction model is developed and applied to estimate the rate of erosion at a selected bend.Finally the predicted results have been compared with the observed data at the bend and all the available data at other bends along the Jamuna River.     

Impact of reach geometry on stream channel sensitivity to extreme floods

Predicting spatial and temporal variations in bank erosion due to extreme floods presents a long‐standing challenge in geomorphology. We develop two methodologies for rapid, regional‐scale assessments of stream reaches susceptible to channel widening. The first proposes that channel widening occurs when unit stream power exceeds a critical threshold (300 W/m²). The second is motivated by the observation that widening often occurs at channel bends. We introduce a new metric, the bend stress parameter, which is proportional to the centripetal force exerted on a concave bank. We propose that high centripetal forces generate locally high bank shear forces and enhance channel bank erosion. We test both metrics using the geomorphic signature of Tropical Storm Irene (2011) on the White and the Saxtons Rivers, Vermont. Specifically, we test if reaches where significant channel widening occurred during Irene required one or both metrics to exceed threshold values. We observe two distinct styles of channel widening. Where unit stream power and bend stress parameter are high, widening is usually due to bank retreat. Elsewhere widening is usually due to the stripping of the upstream end of mid‐channel islands. Excluding widening associated with the stripping of the heads of mid‐channel islands, almost all the widening (> 98%) occurred along reaches identified as susceptible to widening. The combined metrics identify up to one‐quarter of the reaches lacking susceptibility to channel widening. Copyright © 2014 John Wiley & Sons, Ltd.     

Stochastic erosion of composite banks in alluvial river bends

The erosion of composite river banks is a complex process involving a number of factors including fluvial erosion, seepage erosion, and cantilever mass failure. To predict the rate of bank erosion with these complexities, a stochastic bank erosion model is suitable to define the probability distribution of the controlling variables. In this study, a bank erosion model in a river bend is developed by coupling several bank erosion processes with an existing hydrodynamic and morphological model. The soil erodibility of cohesive bank layers was measured using a submerged jet test apparatus. Seasonal bank erosion rates for four consecutive years at a bend in the Brahmaputra River, India, were measured by repeated bankline surveys. The ability of the model to predict erosion was evaluated in the river bend that displayed active bank erosion. In this study, different monsoon conditions and the distribution functions of two variables were considered in estimating the stochastic bank erosion rate: the probability of the soil erodibility and stochastic stage hydrographs for the nth return period river stage. Additionally, the influences of the deflection angle of the streamflow, longitudinal slope of river channel, and bed material size on bank erosion rate were also investigated. The obtained stochastic erosion predictions were compared with the observed distribution of the annual‐average bank erosion rate of 45 river bends in the Brahmaputra River. The developed model appropriately predicted the short‐term morphological dynamics of sand‐bed river bends with composite banks. Copyright © 2014 John Wiley & Sons, Ltd.