Climate change sensitivity assessment of streamflow and agricultural pollutant transport in California's Central Valley using Latin hypercube sampling

Bracketing the uncertainty of streamflow and agricultural runoff under climate change is critical for proper future water resource management in agricultural watersheds. This study used the Soil and Water Assessment Tool (SWAT) in conjunction with a Latin hypercube climate change sampling algorithm to construct a 95% confidence interval (95CI) around streamflow, sediment load, and nitrate load predictions under changes in climate for the Sacramento and San Joaquin River watersheds in California's Central Valley. The Latin hypercube algorithm sampled 2000 combinations of precipitation and temperature changes based on Intergovernmental Panel on Climate Change projections from multiple General Circulation Models. Average monthly percent changes of the upper and lower 95CI limits compared to the present‐day simulation and a statistic termed the “r‐factor” (average width of the 95CI band divided by the standard deviation of the 95CI bandwidth) were used to assess watershed sensitivities. 95CI results indicate that streamflow and sediment runoff in the Sacramento River watershed are more likely to decrease under climate change compared to present‐day conditions, whereas the increase and decrease for nitrate runoff were found to be equal. For the San Joaquin River watershed, streamflow slightly decreased under climate change, whereas sediment and nitrate runoff increased compared to present‐day climate. Comparisons of watershed sensitivities indicate that the San Joaquin River watershed is more sensitive to climate changes than the Sacramento River watershed, which is largely caused by the high density of agricultural land. Copyright © 2012 John Wiley & Sons, Ltd.     

The responses of hydrological processes and sediment yield to land‐use and climate change in the Be River Catchment,Vietnam

In this study, we investigated the responses of hydrology and sediment yield with impacts of land‐use and climate change scenarios in the Be River Catchment, using the Soil and Water Assessment Tool (SWAT) hydrological model. The calibration and validation results indicated that the SWAT model is a powerful tool for simulating the impact of environmental change on hydrology and sediment yield in this catchment. The hydrologic and sediment yield responses to land‐use and climate changes were simulated based on the calibrated model. The results indicated that a 16.3% decrease in forest land is likely to increase streamflow (0.2 to 0.4%), sediment load (1.8 to 3.0%), and surface runoff (SURQ) (4.8 to 10.7%) and to decrease groundwater discharge (GW_Q) (3.5 to 7.9%). Climate change in the catchment leads to decreases in streamflow (0.7 to 6.9%) and GW_Q (3.0 to 8.4%), increase in evapotranspiration (0.5 to 2.9%), and changes in SURQ (?5.3 to 2.3%) and sediment load (?5.3 to 4.4%). The combined impacts of land‐use and climate changes decrease streamflow (2.0 to 3.9%) and GW_Q (12.3 to 14.0%), increase evapotranspiration (0.7 to 2.8%), SURQ (8.2 to 12.4%), and sediment load (2.0 to 7.9%). In general, the separate impacts of climate and land‐use changes on streamflow, sediment load, and water balance components are offset each other. However, SURQ and some component of subsurface flow are more sensitive to land‐use change than to climate change. Furthermore, the results emphasized water scarcity during the dry season and increased soil erosion during the wet season. Copyright © 2012 John Wiley & Sons, Ltd.     

SWAT-based runoff and sediment simulation in a small watershed,the loessial hilly-gullied region of China:capabilities and challenges

Model calibration and validation are necessary before applying it for scenario assessment and watershed management.This study presented the methodology of evaluating Soil and Water Assessment Tool(SWAT) and tested the feasibility of SWAT on runoff and sediment load simulation in the Zhifanggou watershed located in hilly-gullied region of China.Daily runoff and sediment event data from 1998-2008 were used in this study;data from 1998-2003 were used for calibration and 2004-2008 for validation.The evaluation statistics for the daily runoff simulation showed that the model results were acceptable,but the model underestimated the runoff for high-flow events.For sediment load simulation,the SWAT performed well in capturing the trend of sediment load,while the model tended to underestimate sediment load during both the calibration and validation periods. The disparity between observed and simulated data most likely resulted from limitations of the existing SCS-CN and MUSLE methods in the model.This study indicated that the modification of SWAT components is needed to take rainfall intensity and its duration into account to enhance the model performance on peak flow and sediment load simulation during heavy rainfall season.     

Development and application of a physically based landscape water balance in the SWAT model

Watershed scale hydrological and biogeochemical models rely on the correct spatial‐temporal prediction of processes governing water and contaminant movement. The Soil and Water Assessment Tool (SWAT) model, one of the most commonly used watershed scale models, uses the popular curve number (CN) method to determine the respective amounts of infiltration and surface runoff. Although appropriate for flood forecasting in temperate climates, the CN method has been shown to be less than ideal in many situations (e.g. monsoonal climates and areas dominated by variable source area hydrology). The CN model is based on the assumption that there is a unique relationship between the average moisture content and the CN for all hydrologic response units (HRUs), and that the moisture content distribution is similar for each runoff event, which is not the case in many regions. Presented here is a physically based water balance that was coded in the SWAT model to replace the CN method of runoff generation. To compare this new water balance SWAT (SWAT‐WB) to the original CN‐based SWAT (SWAT‐CN), two watersheds were initialized; one in the headwaters of the Blue Nile in Ethiopia and one in the Catskill Mountains of New York. In the Ethiopian watershed, streamflow predictions were better using SWAT‐WB than SWAT‐CN [Nash–Sutcliffe efficiencies (NSE) of 0·79 and 0·67, respectively]. In the temperate Catskills, SWAT‐WB and SWAT‐CN predictions were approximately equivalent (NSE > 0·70). The spatial distribution of runoff‐generating areas differed greatly between the two models, with SWAT‐WB reflecting the topographical controls imposed on the model. Results show that a water balance provides results equal to or better than the CN, but with a more physically based approach. Copyright © 2010 John Wiley & Sons, Ltd.     

Incorporating landscape depression heterogeneity into the Soil and Water Assessment Tool (SWAT) using a probability distribution

Modelling the hydrology of North American Prairie watersheds is complicated because of the existence of numerous landscape depressions that vary in storage capacity. The Soil and Water Assessment Tool (SWAT) is a widely applied model for long‐term hydrological simulations in watersheds dominated by agricultural land uses. However, several studies show that the SWAT model has had limited success in handling prairie watersheds. In past works using SWAT, landscape depression storage heterogeneity has largely been neglected or lumped. In this study, a probability distributed model of depression storage is introduced into the SWAT model to better handle landscape storage heterogeneity. The work utilizes a probability density function to describe the spatial heterogeneity of the landscape depression storages that was developed from topographic characteristics. The integrated SWAT–PDLD model is tested using datasets for two prairie depression dominated watersheds in Canada: the Moose Jaw River watershed, Saskatchewan; and the Assiniboine River watershed, Saskatchewan. Simulation results were compared to observed streamflow using graphical and multiple statistical criterions. Representation of landscape depressions within SWAT using a probability distribution (SWAT–PDLD) provides improved estimations of streamflow for large prairie watersheds in comparison to results using a lumped, single storage approach. Copyright © 2016 John Wiley & Sons, Ltd.     

The NHDPlus dataset,watershed subdivision and SWAT model performance

Abstract

The Soil and Water Assessment Tool (SWAT) has been developed to evaluate the effectiveness of agricultural management practices on watershed water quality. Many studies have indicated that watershed subdivision can affect the accuracy of model predictions. Most of them used the minimum drainage area (MDA) to delineate sub-watersheds, and varied the value of MDA depending on the size of the watershed being modelled. Instead of MDA, we use the National Hydrography Dataset Plus (NHDPlus)—an integration of the best features of the National Hydrography Dataset (NHD), Watershed Boundary Dataset (WBD), National Elevation Dataset (NED), and the National Land Cover Dataset (NLCD)—to delineate the watershed. The Kaskaskia River watershed in Illinois, USA, was selected to investigate the individual effects of sub-watershed and hydrologic response unit (HRU) delineations on predicted streamflow, total suspended sediment (TSS) and total nitrogen (TN) losses at two USGS gauges. In addition, an MDA of 3000 ha, and four levels of stream (the 2nd, 3rd, 4th and 5th order) were evaluated. Three levels of HRU threshold (5%, 10% and 15%) were used for each stream order model. The results show that stream order had little effect on predicted streamflow, but a great impact on TSS and TN losses, and the impact of HRU delineation became greater when a higher stream order was used to delineate the watershed. For higher stream order, fewer streams were recognized in SWAT simulations, which resulted in less sediment routing and channel processes, which, in turn, led to less deposition in the channels; thus high sediment losses were obtained at the watershed outlet. However, fewer channel processes led to less in-stream N processes; thus lower TN losses. Overall, the SWAT simulations performed the best when the 2nd stream order was used for delineations comparing with USGS observed data, followed by the 3rd stream order. Therefore, to fully depict the watershed characteristics to perform SWAT simulations, a stream order higher than 3rd order is not recommended for watershed delineation.

Editor D. Koutsoyiannis; Associate editor C. Perrin     

Hydrological modelling of a small watershed using generated rainfall in the soil and water assessment tool model

An adequately tested soil and water assessment tool (SWAT) model was applied to the runoff and sediment yield of a small agricultural watershed in eastern India using generated rainfall. The capability of the model for generating rainfall was evaluated for a period of 18 years (1981–1998). The watershed and subwatershed boundaries, drainage networks, slope, soil series and texture maps were generated using a geographical information system (GIS). A supervised classification method was used for land‐use/cover classification from satellite imageries. Model simulated monthly rainfall for the period of 18 years was compared with observations. Simulated monthly rainfall, runoff and sediment yield values for the monsoon season of 8 years (1991–1998) were also compared with their observed values. In general monthly average rainfall predicted by the model was in close agreement with the observed monthly average values. Also, simulated monthly average values of surface runoff and sediment yield using generated rainfall compared well with observed values during the monsoon season of the years 1991–1998. Results of this study revealed that the SWAT model can generate monthly average rainfall satisfactorily and thereby can produce monthly average values of surface runoff and sediment yield close to the observed values. Therefore, it can be concluded that the SWAT model could be used for developing a multiple year management plan for the critical erosion prone areas of a small watershed. Copyright © 2004 John Wiley & Sons, Ltd.     

Distinct effects of temperature change on discharge and non-point pollution in subtropical southern China by SWAT simulation

Abstract

Climate change impacts on the availability of water resources. Projection of hydrological response to temperature change is valuable for water management. Such response may be complex and uncertain at the watershed scale and differences may exist between low and high latitudes. A simulation experiment was achieved by using SWAT modelling in the upstream watershed of Dongjiang River, South China. After calibration, the model was found appropriate for hydrological simulation in the study area and was run from 1995 to 2004 under a series of temperature change scenarios to reveal the response of streamflow and loads of sediment and nutrients. For a temperature increase of 3°C, streamflow, sediment and total phosphorus decreased by 5.2, 7.7 and 2.2%, respectively. Linear temperature change seemed to have a linear hydrological response. Nutrient deficiency was still the primary vegetation stress compared with water availability and temperature stress under rising temperatures. Comparison with previous research showed that two southern subtropical watersheds (one upstream and one downstream) gave different hydrological responses. Sediment and inorganic nitrogen loads decreased in the upstream watershed, but increased in the downstream one, when temperature increased. Under the warming scenarios, streamflow and sediment loads decreased throughout the year, especially during the wet season, which is different from results at high latitudes. Nutrient export decreased in April–June, but increased in the remaining months. Simulation results should be applied with caution in water resources management, as simulated climate change had variable hydrological influence in different regions and seasons.

Citation Xu, H. and Peng, S.L., 2013. Distinct effects of temperature change on discharge and non-point pollution in subtropical southern China by SWAT simulation. Hydrological Sciences Journal, 58 (5), 1032–1046.

Editor Z.W. Kundzewicz; Associate editor C.-Y. Xu     

Development of a grid‐based version of the SWAT landscape model

Integrated river basin models should provide a spatially distributed representation of basin hydrology and transport processes to allow for spatially implementing specific management and conservation measures. To accomplish this, the Soil and Water Assessment Tool (SWAT) was modified by integrating a landscape routing model to simulate water flow across discretized routing units. This paper presents a grid‐based version of the SWAT landscape model that has been developed to enhance the spatial representation of hydrology and transport processes. The modified model uses a new flow separation index that considers topographic features and soil properties to capture channel and landscape flow processes related to specific landscape positions. The resulting model is spatially fully distributed and includes surface, lateral and groundwater fluxes in each grid cell of the watershed. Furthermore, it more closely represents the spatially heterogeneous distributed flow and transport processes in a watershed. The model was calibrated and validated for the Little River Watershed (LRW) near Tifton, Georgia (USA). Water balance simulations as well as the spatial distribution of surface runoff, subsurface flow and evapotranspiration are examined. Model results indicate that groundwater flow is the dominant landscape process in the LRW. Results are promising, and satisfactory output was obtained with the presented grid‐based SWAT landscape model. Nash–Sutcliffe model efficiencies for daily stream flow were 0.59 and 0.63 for calibration and validation periods, and the model reasonably simulates the impact of the landscape position on surface runoff, subsurface flow and evapotranspiration. Additional revision of the model will likely be necessary to adequately represent temporal variations of transport and flow processes in a watershed. Copyright © 2014 John Wiley & Sons, Ltd.     

Comparison of daily and sub-daily SWAT models for daily streamflow simulation in the Upper Huai River Basin of China

Despite the significant role of precipitation in the hydrological cycle, few studies have been conducted to evaluate the impacts of the temporal resolution of rainfall inputs on the performance of SWAT (soil and water assessment tool) models in large-sized river basins. In this study, both daily and hourly rainfall observations at 28 rainfall stations were used as inputs to SWAT for daily streamflow simulation in the Upper Huai River Basin. Study results have demonstrated that the SWAT model with hourly rainfall inputs performed better than the model with daily rainfall inputs in daily streamflow simulation, primarily due to its better capability of simulating peak flows during the flood season. The sub-daily SWAT model estimated that 58 % of streamflow was contributed by baseflow compared to 34 % estimated by the daily model. Using the future daily and 3-h precipitation projections under the RCP (Representative Concentration Pathways) 4.5 scenario as inputs, the sub-daily SWAT model predicted a larger amount of monthly maximum daily flow during the wet years than the daily model. The differences between the daily and sub-daily SWAT model simulation results indicated that temporal rainfall resolution could have much impact on the simulation of hydrological process, streamflow, and consequently pollutant transport by SWAT models. There is an imperative need for more studies to examine the effects of temporal rainfall resolution on the simulation of hydrological and water pollutant transport processes by SWAT in river basins of different environmental conditions.     

SWAT model application and prediction uncertainty analysis in the Lake Tana Basin,Ethiopia

Lake Tana Basin is of significant importance to Ethiopia concerning water resources aspects and the ecological balance of the area. Many years of mismanagement, wetland losses due to urban encroachment and population growth, and droughts are causing its rapid deterioration. The main objective of this study was to assess the performance and applicability of the soil water assessment tool (SWAT) model for prediction of streamflow in the Lake Tana Basin, so that the influence of topography, land use, soil and climatic condition on the hydrology of Lake Tana Basin can be well examined. The physically based SWAT model was calibrated and validated for four tributaries of Lake Tana. Sequential uncertainty fitting (SUFI‐2), parameter solution (ParaSol) and generalized likelihood uncertainty estimation (GLUE) calibration and uncertainty analysis methods were compared and used for the set‐up of the SWAT model. The model evaluation statistics for streamflows prediction shows that there is a good agreement between the measured and simulated flows that was verified by coefficients of determination and Nash Sutcliffe efficiency greater than 0·5. The hydrological water balance analysis of the basin indicated that baseflow is an important component of the total discharge within the study area that contributes more than the surface runoff. More than 60% of losses in the watershed are through evapotranspiration. Copyright © 2009 John Wiley & Sons, Ltd.     

Impacts of land-use changes on watershed discharge and water quality in a large intensive agricultural area in Thailand

The objectives of this research were to evaluate the effect of land-use change on streamflow, sediment and water quality data along the Lower Yom River, Thailand, covering an intensively agricultural area of 14 613.6 km², and to assess the relative impact of point and non-point sources of pollution from multiple-land-use watersheds. Long-term calibration and validation of the SWAT (Soil and Water Assessment Tool) model was performed on data for 2000–2013. Land-use change led to a 13–49% increase in runoff in the basin and resulted in 37–427% increased sediment yield. The amount of NO₃-N load doubled in the upper and middle parts of the study area, while the increase in PO₄^3– ranged from 37 to 377%, reflecting the increase in agricultural lands and urban areas. It is concluded that the changed land use is closely associated with the quantity of runoff, sediment yield and the NO₃-N and PO₄^3– concentrations.     

Hydrological impact of roadside ditches in an agricultural watershed in Central New York: implications for non‐point source pollutant transport

Nonpoint source pollution and hydromodification are the leading causes of impairment to our nation's rivers and streams. Roadside ditch networks, ubiquitous in both rural and urban landscapes, intercept and shunt substantial quantities of overland runoff and shallow groundwater to stream systems. By altering natural flowpaths, road ditches contribute not only to hydromodification but also potentially to nonpoint‐source (NPS) pollution by acting as hydrological links between agricultural fields and natural streams. Unfortunately, the impacts of these alterations on watershed hydrology and water quality are not well understood. Through a series of field measurements, including field surveys and discharge monitoring, this study examined the effect of road ditch networks on basin morphometry, field‐ and watershed‐scale hydrology, and pollutant transport in a 38 km² agricultural watershed in south‐central NY. Salient findings include the following: (i) 94% of road ditches discharged to natural streams, effectively doubling the drainage density; (ii) on average, road ditches increased peak and total event flows in their receiving streams by 78% and 57%, respectively, but displayed significant variation across ditches; and (iii) ditches intercepted large quantities of surface and subsurface runoff from agricultural fields and therefore represent efficient conduits for the transport of agricultural NPS pollutants to sensitive receiving waterbodies. Our results provide useful information for hydrologists who wish to further understand how artificial drainage may be affecting watershed hydrology and for managers and engineers tasked with designing appropriate flood and NPS pollution control measures. Copyright © 2012 John Wiley & Sons, Ltd.     

Improvement of SWAT2000 modelling to assess the impact of dams and sluices on streamflow in the Huai River basin of China

Hydrological simulation and assessment in a dam–sluice regulated river basin are a complex and challenging issue. In this article, an improved SWAT2000 modelling system was developed that incorporated the Shuffled complex evolution (SCE‐UA) optimization algorithm and the multi‐site and multi‐objective calibration strategy. The implication of multi‐objective is different for different types of outlets, i.e. streamflow for an ordinary outlet, inflow for a sluice, and water storage for a reservoir. Model parameters were redefined to improve model simulations. The surface runoff lag time (SURLAG) was extended as a spatially distributed parameter, and a correction coefficient was introduced to modify the saturated hydraulic conductivity. The modelling system was then applied to the Huai River basin of China under various climatic conditions, including a very dry year (1999), a dry year (1981), an average year (1971), and wet year (1991). In all, 26 dams and 35 sluices were considered, among which about 20 dams/sluices were used for model calibration. The impact assessment primarily focused on the very dry year (1999). The results indicated that the released water from large reservoirs was blocked in the river channels by sluices located downstream. In the very dry year, the dam–sluice operations could result in an increase of the runoff volume during the non‐flood season and a decrease in runoff during the flood season, but the changing magnitude during the non‐flood season was much greater. An important conclusion of this case study is that the sluices in the Sha‐Yin branch located in the north region and the dams in the southern mountainous region above the Wangjiaba Hydrological Station have played the most significant role in regulating the streamflow of the entire river basin. The methods addressed in this article can simulate hydrological regime in the river basins regulated by dams and sluices under different climatic conditions at the whole‐watershed scale. Copyright © 2010 John Wiley & Sons, Ltd.     

The impact of climatic variability and change in the hydroclimatology of Lake Winnipeg watershed

The hydroclimatology of prairie‐dominated portions of the Lake Winnipeg watershed was investigated to determine the possible presence of trends and shifts in variables that may influence the streamflow regimes and water quality of Lake Winnipeg. The total annual streamflow, precipitation, runoff ratio and daily maximum streamflow in the two major tributaries of the Assiniboine River and Red River were analysed for a range of nonstationary behaviours. Each of these rivers has been gauged for more than 90 years. The methods used included a nonparametric Mann–Kendall test modified to account for diverse memory properties (i.e. short term versus long term) and a Bayesian change point detection model to identify possible segments of time series with inconsistent nonstationary behaviour. Although there is no evidence of statistically significant trends in precipitation and streamflow in the Assiniboine River watershed, a shift‐type nonstationarity in annual runoff and runoff ratio was observed in this area, which is manifested in the form of a sequence of wet and dry spells during the last century. Precipitation and runoff metrics in the American portion of the study area (i.e. Red River watershed) were characterised with both gradual and abrupt changes with an extremely increasing rate of streamflow beyond that of intensified precipitation. The nonproportional watershed runoff response is attributed to the dynamic nature of contributing areas that, together with the semiarid climate, leads to sudden changes of streamflow due to major or even some times minor changes in climate inputs. It is evident that streamflow in the depression‐dominated landscapes of the semiarid glaciated plains of North America is particularly sensitive and vulnerable to minor climate variability and change. This study provides valuable insights into the highly complex precipitation–runoff relationship in depression‐dominated landscapes and could have important implications for water management in this part of North America and comparable regions. Copyright © 2011 John Wiley & Sons, Ltd.     

Comparison of AnnAGNPS and SWAT model simulation results in USDA‐CEAP agricultural watersheds in south‐central Kansas

This study was conducted under the USDA‐Conservation Effects Assessment Project (CEAP) in the Cheney Lake watershed in south‐central Kansas. The Cheney Lake watershed has been identified as ‘impaired waters’ under Section 303(d) of the Federal Clean Water Act for sediments and total phosphorus. The USDA‐CEAP seeks to quantify environmental benefits of conservation programmes on water quality by monitoring and modelling. Two of the most widely used USDA watershed‐scale models are Annualized AGricultural Non‐Point Source (AnnAGNPS) and Soil and Water Assessment Tool (SWAT). The objectives of this study were to compare hydrology, sediment, and total phosphorus simulation results from AnnAGNPS and SWAT in separate calibration and validation watersheds. Models were calibrated in Red Rock Creek watershed and validated in Goose Creek watershed, both sub‐watersheds of the Cheney Lake watershed. Forty‐five months (January 1997 to September 2000) of monthly measured flow and water quality data were used to evaluate the two models. Both models generally provided from fair to very good correlation and model efficiency for simulating surface runoff and sediment yield during calibration and validation (correlation coefficient; R², from 0·50 to 0·89, Nash Sutcliffe efficiency index, E, from 0·47 to 0·73, root mean square error, RMSE, from 0·25 to 0·45 m³ s^?1 for flow, from 158 to 312 Mg for sediment yield). Total phosphorus predictions from calibration and validation of SWAT indicated good correlation and model efficiency (R² from 0·60 to 0·70, E from 0·63 to 0·68) while total phosphorus predictions from validation of AnnAGNPS were from unsatisfactory to very good (R² from 0·60 to 0·77, E from ? 2·38 to 0·32). The root mean square error–observations standard deviation ratio (RSR) was estimated as excellent (from 0·08 to 0·25) for the all model simulated parameters during the calibration and validation study. The percentage bias (PBIAS) of the model simulated parameters varied from unsatisfactory to excellent (from 128 to 3). This study determined SWAT to be the most appropriate model for this watershed based on calibration and validation results. Copyright © 2008 John Wiley & Sons, Ltd.     

Predicting saturation‐excess runoff distribution with a lumped hillslope model: SWAT‐HS

Saturation‐excess runoff is the major runoff mechanism in humid well‐vegetated areas where infiltration rates often exceed rainfall intensity. Although the Soil and Water Assessment Tool (SWAT) is one of the most widely used models, it predicts runoff based mainly on soil and land use characteristics, and is implicitly an infiltration‐excess runoff type of model. Previous attempts to incorporate the saturation‐excess runoff mechanism in SWAT fell short due to the inability to distribute water from one hydrological response unit to another. This paper introduces a modified version of SWAT, referred to as SWAT‐Hillslope (SWAT‐HS). This modification improves the simulation of saturation‐excess runoff by redefining hydrological response units based on wetness classes and by introducing a surface aquifer with the ability to route interflow from “drier” to “wetter” wetness classes. Mathematically, the surface aquifer is a nonlinear reservoir that generates rapid subsurface stormflow as the water table in the surface aquifer rises. The SWAT‐HS model was tested in the Town Brook watershed in the upper reaches of the West Branch Delaware River in the Catskill region of New York, USA. SWAT‐HS predicted discharge well with a Nash‐Sutcliffe Efficiency of 0.68 and 0.87 for daily and monthly time steps. Compared to the original SWAT model, SWAT‐HS predicted less surface runoff and groundwater flow and more lateral flow. The saturated areas predicted by SWAT‐HS were concentrated in locations with a high topographic index and were in agreement with field observations. With the incorporation of topographic characteristics and the addition of the surface aquifer, SWAT‐HS improved streamflow simulation and gave a good representation of saturated areas on the dates that measurements were available. SWAT‐HS is expected to improve water quality model predictions where the location of the surface runoff matters.     

Impact of climate and land-use changes on hydrological processes and sediment yield—a case study of the Be River catchment,Vietnam

Abstract

The impact of climate and land-use changes on hydrological processes and sediment yield is investigated in the Be River catchment, Vietnam, using the Soil and Water Assessment Tool (SWAT) hydrological model. The sensitivity analysis, model calibration and validation indicated that the SWAT model could reasonably simulate the hydrology and sediment yield in the catchment. From this, the responses of the hydrology and sediment to climate change and land-use changes were considered. The results indicate that deforestation had increased the annual flow (by 1.2%) and sediment load (by 11.3%), and that climate change had also significantly increased the annual streamflow (by 26.3%) and sediment load (by 31.7%). Under the impact of coupled climate and land-use changes, the annual streamflow and sediment load increased by 28.0% and 46.4%, respectively. In general, during the 1978–2000 period, climate change influenced the hydrological processes in the Be River catchment more strongly than the land-use change.

Editor Z.W. Kundzewicz; Associate editor Q. Zhang

Citation Khoi, D.N. and Suetsugi, T., 2014. Impact of climate and land-use changes on hydrological processes and sediment yield—a case study of the Be River catchment, Vietnam. Hydrological Sciences Journal, 59 (5), 1095–1108.     

Assessment of runoff and sediment yield in the Miyun Reservoir catchment by using SWAT model

The Soil and Water Assessment Tool (SWAT) was used to simulate the transport of runoff and sediment into the Miyun Reservoir, Beijing in this study. The main objective was to validate the performance of SWAT and the feasibility of using this model as a simulator of runoff and sediment transport processes at a catchment scale in arid and semi‐arid area in North China, and related processes affecting water quantity and soil erosion in the catchment were simulated. The investigation was conducted using a 6‐year historical streamflow and sediment record from 1986 to 1991; the data from 1986 to 1988 was used for calibration and that from 1989 to 1991 for validation. The SWAT generally performs well and could accurately simulate both daily and monthly runoff and sediment yield. The simulated daily and monthly runoff matched the observed values satisfactorily, with a Nash‐Sutcliffe coefficient of greater than 0·6, 0·9 and a coefficient of determination 0·75, 0·9 at two outlet stations (Xiahui and Zhangjiafen stations) during calibration. These values were 0·6, 0·85 and 0·6, 0·9 during validation. For sediment simulation, the efficiency is lower than that for runoff. Even so, the Nash‐Sutcliffe coefficient and coefficient of determination were greater than 0·48 and 0·6 for monthly sediment yield during calibration, and these values were greater than 0·84 and 0·95 during validation. Sensitivity analysis shows that sensitive parameters for the simulation of discharge and sediment yield include curve number, base flow alpha factor, soil evaporation compensation factor, soil available water capacity, soil profile depth, surface flow lag time and channel re‐entrained linear parameter, etc. Copyright © 2009 John Wiley & Sons, Ltd.     

Hydrologic comparison between a forested and a wetland/lake dominated watershed using SWAT

The Soil and Water Assessment Tool (SWAT) is a physically‐based hydrologic model developed for agricultural watersheds, which has been infrequently validated for forested watersheds, particularly those with deep overwinter snow accumulation and abundant lakes and wetlands. The goal of this study was to determine the applicability of SWAT for modelling streamflow in two watersheds of the Ontonagon River basin of northern Michigan which differ in proportion of wetland and lake area. The forest‐dominated East Branch watershed contains 17% wetland and lake area, whereas the wetland/lake‐dominated Middle Branch watershed contains 26% wetland and lake area. The specific objectives were to: (1) calibrate and validate SWAT models for the East Branch and Middle Branch watersheds to simulate monthly stream flow, and (2) compare the effects of wetland and lake abundance on the magnitude and timing of streamflow. Model calibration and validation was satisfactory, as determined by deviation of discharge D and Nash and Sutcliffe coefficient values E that compared simulated monthly mean discharge versus measured monthly mean discharge. Streamflow simulation discrepancies occurred during summer and fall months and dry years. Several snow melting parameters were found to be critical for the SWAT simulation: TIMP (snow temperature lag factor) and SMFMX and SMFMN (melting factors). Snow melting parameters were not transferable between adjacent watersheds. Differences in seasonal pattern of long‐term monthly streamflow were found, with the forest‐dominated watershed having a higher peak flow during April but a lower flow during the remainder of the year in comparison to the wetland and lake‐dominated watershed. The results suggested that a greater proportion of wetland and lake area increases the capacity of a watershed to impound surface runoff and to delay storm and snow melting events. Representation of wetlands and lakes in a watershed model is required to simulate monthly stream flow in a wetland/lake‐dominated watershed. Copyright © 2007 John Wiley & Sons, Ltd.