约束砖砌体结构的弹塑性时程分析

本文对超《规范》的大开间采取在墙体中增设钢筋混凝土墙中柱和水平条带的加强措施，为验证原型结构的抗震能力，在大比例模型试验的基础上，对约束砖砌体原型结构进行弹塑性时程分析，得出结构层次位移反应包络图，论证了结构采取此项加强措施后能满足7度区相应的抗震设防要求。     

配筋砌体结构抗震能力的试验研究

根据砖砌体结构在地震作用下主要表现为剪切破坏的特点，采用子结构拟动力试验技术配筋砌体记房屋结构进行了抗震试验研究。可以改善砖砌体结构在极限荷载后的性能，提高结构的抗震能力。     

理性思考汶川地震中砌体结构的抗震能力

汶川地震建筑震害严重,应对此进行理性的思考。本文立足于按规范正常建造的砌体结构房屋的震害调查,对砌体结构震害严重的原因进行了分析,提出了减轻砌体结构震害的建议;同时,对预制板在地震区的应用进行了探讨,指出政府不宜限制预制板的应用;最后,建议采用经济性好、施工快捷、结构性能可靠的新型装配整体式房屋结构体系等技术。     

外套预制砌体加固结构的应用及弹塑性分析

目前城市中存在着大量的老旧砌体房屋,由于建造年代久远,房屋大多缺乏抗震设计,存在着严重的安全隐患。应用外套预制装配技术对上海市某6层砌体结构进行加固改造,并应用结构分析软件SAP2000进行砌体结构弹塑性分析。通过加固前后结构地震响应分析,结果表明：相比于原结构,加固后砌体部分承担基底剪力小震和大震分别减小51.21%和13.70%,原砌体结构承担剪力得到有效削弱。原结构小震层间位移角大于1/2 000,可能发生轻微破坏,大震层间位移角大于1/250,存在倒塌风险。加固后砌体结构抗震性能得到明显改善,小震层间位移角小于1/3 500,大震层间位移角小于1/600,小震下可保证结构基本完好,大震下不致结构发生严重破坏,有效地提高了原结构抗震能力。加固后砌体结构峰值位移平均降幅在40%～90%之间,在小震作用下,加速度减小,而大震作用下则反向增大。     

芦山7.0级地震砌体结构的震害特征

四川芦山7.0级强烈地震影响区域内有大量的砌体结构房屋,既有未采取任何抗震构造措施的非约束砌体结构,也有设置了圈梁和构造柱的约束砌体结构.文中首先简要讨论了本次地震强震动特性,表明其高频成分丰富,反应谱中低频部分衰减较快,是刚性结构和柔性结构地震破坏表现差别较大的原因之一;继而论文重点以现场震害调查资料为基础,总结了不同烈度区、不同类型砌体结构的震害特征;高烈度区不同类型砌体结构的震害程度和破坏比对比表明,约束砌体结构的抗震性能明显优于非约束砌体结构.     

配筋混凝土砌块砌体高层模拟结构抗震分析

以上海园南小区配筋砌块砌体高层住宅作为原型结构，通过变化结构的一些基本参数，模拟成一系列新的结构，对模拟结构进行了抗震分析，研究了结构参数对配筋砌块砌体结构抗震性能的影响。     

配筋砌体结构地震易损性评价方法初探

本文首先简要介绍了考虑空间协同的配筋砌体结构弹塑性地震反应分析程序EDAPSC；然后提出了一种利用空间协同时程分析结果，对配筋砌体结构地震易损性进行定量评价的方法，并以上海园南小区住宅楼为例进行了地震易损性分析，说明本文提出的地震易损性评价方法是可行和合理的；另外作者还对设计人员提出了提高结构抗震安全性的建议。     

构造柱和砌筑砂浆对砌体结构抗震能力影响分析

以汶川地震宏观震中映秀镇(实际烈度Ⅺ度)中裂而未倒且保存较完好的漩口中学南西栋教师宿舍楼为原型,采用有限元软件ABAQUS进行建模分析,研究构造柱布置数量、砂浆强度对砌体结构抗震能力的影响。分别通过改变构造柱布置数量和砂浆强度等级,建立3个模型进行对比分析,选取底层间位移角最大值作为衡量标准。研究结果表明:在遭遇烈度不高于Ⅷ度的地震时,构造柱的作用微乎其微,其布置数量的多少对砌体结构抗震能力的增加效果不明显;在遭遇烈度高于Ⅷ度的地震时,构造柱作用能够显现出来,其布置数量的增加能够有效增加砌体结构的抗震能力;砌体结构的抗震性能随砂浆强度等级的增加而提高。     

三向地震作用下砌体结构抗震性能研究

本文首先介绍了两个砌体结构模型在三向地震作用下的地震模拟振动台试验，在此基础上，运用参数识别技术，对试验数据进行了参数识别计算，最后，分析了三向地震作用对砌体结构抗震性能的影响。     

关于提高中小学砌体建筑抗震能力的讨论

利用汶川8.0级地震特大发生后作者在极重灾区——四川省广元市青川县参加首批房屋应急评估工作期间收集的房屋震害资料,分析了砌体结构的震害特点和震害原因,对提高中小学砌体建筑抗震能力进行研究,从概念设计与计算分析两个方面对现行抗震设计规范的若干条文进行了讨论,提出了验算砌体结构抗倒塌能力的建议。     

Seismic behaviour of confined masonry walls

The results of tests of plain and confined masonry walls with h/l ratio equal to 1·5, made at 1:5 scale, have been used to develop a rational method for modelling the seismic behaviour of confined masonry walls. A trilinear model of lateral resistance–displacement envelope curve has been proposed, where the resistance is calculated as a combination of the shear resistance of the plain masonry wall panel and dowel effect of the tie-columns’ reinforcement. Lateral stiffness, however, is modelled as a function of the initial effective stiffness and damage, occurring to the panel at characteristic limit states. Good correlation between the predicted and experimental envelopes has been obtained in the particular case studied. The method has been also verified for the case of prototype confined masonry walls with h/l ratio equal to 1·0. Good correlation between the predicted and experimental values of lateral resistance indicates the general validity of the proposed method. © 1997 John Wiley & Sons, Ltd.     

砖墙体抗震承载力仿真分析与试验对比

为研究竖向压应力和高宽比对砖墙体抗震性能的影响,以砖墙体抗震承载力典型试验试件为基础,利用有限元分析软件ANSYS建立适当的空间模型。根据砖墙体的破坏模式和材料性能把墙体划分成块体单元、灰缝单元以及接触单元,为各部分材料选用不同的本构关系模型与破坏准则。并将计算结果与试验结果进行对比,验证文中模型的可适用性。选用经验证后的模型,变换竖向压应力和高宽比,得出相应的结论:墙体的开裂荷载和抗侧承载力随着高宽比的增大明显呈降低的趋势;不同高宽比的墙体,竖向压应力的影响规律不尽相同。     

砌体结构工程抗震软件的结构隔震功能及算例分析

在砌体结构抗震软件开发过程中，为完善软件功能，添加了结构减震设计验算程序。作为首次应用性软件开发，暂只包含橡胶热隔震的设计与验算功能。本文主要介绍了软件应用时，橡胶垫隔震支座的设计过程，并通过对一个模拟的8层砌体建筑进行隔震设计与对比分析，给出了隔震设计后隔震效果的有关结论。     

In‐plane and out‐of‐plane behavior of confined masonry walls for various toothing and openings details and prediction of their strength and stiffness

Eight half‐scale brick masonry walls were tested to study two important aspects of confined masonry (CM) walls related to its seismic behavior under in‐plane and out‐of‐plane loads. Four solid wall specimens tested to investigate the role of type of interface between the masonry and tie‐columns, such as toothing varying from none to every course. The other four specimens with openings were tested to study the effectiveness of various strengthening options around opening to mitigate their negative influence. In the set of four walls, one wall was infilled frame while the other three were CM walls of different configurations. The experimental results were further used to determine the accuracy of various existing models in predicting the in‐plane response quantities of CM walls. Confined masonry walls maintained structural integrity even when severely damaged and performed much better than infill frames. No significant effect of toothing details was noticed although toothing at every brick course was preferred for better post‐peak response. For perforated walls, provision of vertical elements along with continuous horizontal bands around openings was more effective in improving the overall response. Several empirical and semi‐empirical equations are available to estimate the lateral strength and stiffness of CM walls, but those including the contribution of longitudinal reinforcement in tie‐columns provided better predictions. The available equations along with reduction factors proposed for infills could not provide good estimates of strength and stiffness for perforated CM walls. However, recently proposed relations correlating strength/stiffness with the degree of confinement provided reasonable predictions for all wall specimens. Copyright © 2016 John Wiley & Sons, Ltd.     

新型混凝土空心砌块房屋抗震性能研究

本文介绍了一种集承重与保温于一体的新型混凝土砌块房屋的抗震性能的研究结果。文中采用具有负刚度的四折线恢复力模型，用Newmark数值积分法，选用代表I-Ⅳ类场地的10地震记录，分别对两栋典型的新型砌块房屋进行了非线性地震反应分析，研究了在抗震设防“三水准”情况下房屋的抗震能力。计算结果表明：新型砌块房屋具有良好的抗震性能，在7、8度地震区分别建造7层和6层的这种房屋可满足抗震设防三水准要求。文中还介绍了一个足尺新型砌块房屋模型的模拟振动台试验，用本文给出的非线性地震反应分析方法对模型进行了计算，且将振动台试验结果与计算结果做了比较，验证了本文选取的计算模型是合理的、计算方法是可靠的。     

多层错层砖砌体房屋抗震分析

本文根据典型的东西和南北错层单元模型,按不同的错层高度、不同收层情况和不同理置深度的实际房屋情况,分析建立了错层房层和相应的等效规整房屋模型,采用板壳单元,用有限元方法计算了这些模型的动力特征和在地震作用下的墙肢剪应力分布,经过对比分析得到了一些错层房屋墙应力的分布规律。根据错层房屋的受力特点,文中提出了相应的加强构造措施,结构布置要求和错层房屋的抗震计算模型等具体建议。     

Experimental and analytical studies on earthquake resisting behaviour of confined concrete block masonry structures

To improve the seismic performance of masonry structures, confined masonry that improves the seismic resistance of masonry structures by the confining effect of surrounding bond beams and tie columns is constructed. This study investigated the earthquake resisting behaviour of confined masonry structures that are being studied and constructed in China. The structural system consists of unreinforced block masonry walls with surrounding reinforced concrete bond beams and tie columns. The characteristics of the structure include: (1) damage to blocks is reduced and brittle failure is avoided by the comparatively lower strength of the joint mortar than that of the blocks, (2) the masonry walls and surrounding reinforced concrete bond beams and tie columns are securely jointed by the shear keys of the tie columns. In this study, wall specimens made of concrete blocks were tested under a cyclic lateral load and simulated by a rigid body spring model that models non‐linear behaviour by rigid bodies and boundary springs. The results of studies outline the resisting mechanism, indicating that a rigid body spring model is considered appropriate for analysing this type of structure. Copyright © 2006 John Wiley & Sons, Ltd.     

Seismic capacity of irregular unreinforced masonry walls with openings

Masonry buildings are often characterized by geometric irregularities. In many cases, such buildings meet global regularity requirements provided by seismic codes, but they are composed by irregular walls with openings. The latter are masonry walls characterized by (i) openings of different sizes, (ii) openings misaligned in the horizontal and/or vertical direction, or (iii) a variable number of openings per story. An irregular layout of openings can induce not only a nonuniform distribution of gravity loads among masonry piers but also unfavorable damage localizations resulting in a premature collapse of the wall and hence a higher seismic vulnerability. This paper is aimed at providing a simplified methodology to assess the effects of irregularities on the in‐plane seismic capacity of unreinforced masonry (URM) walls with openings. To this end, a macroelement method was developed and validated through experimental results available in the literature. The proposed methodology was based on the quantification of wall irregularities by means of geometric indices and their effects on seismic capacity of URM walls with openings through both sensitivity and regression analyses. Sensitivity analysis was based on a high number of static pushover analyses and allowed to assess variations in key seismic capacity parameters. Regression analysis let to describe each capacity parameter under varying irregularity index, providing empirical models for seismic assessment of irregular URM walls with openings. The in‐plane seismic capacity was found to be significantly affected by wall irregularities, especially in the case of openings with different heights. Copyright © 2012 John Wiley & Sons, Ltd.     

新型灌浆材料在已建砌体结构抗震加固中的应用

具有悠久历史的石结构是砌体结构的重要组成部分，本文作者经广泛调研和试验分析：(1)提出以石粉为集料对石砌体进行抗震加固，寓环保与防灾于一体；(2)给出新型浆体配比和复合砂浆的强度等级，阐述加固技术和方法，建立灌浆石砌体抗震抗剪强度公式；(3)阐明抗震验算方法，提出基于模糊随机可靠理论的可靠性分析方法。