Aeromagnetic surveying using a simulated unmanned aircraft system

Carleton University and Sander Geophysics are developing an unmanned aircraft system (UAS) for aeromagnetic surveying. As an early indication of the expected performance of the unmanned aircraft system, a simulated unmanned aircraft system (sUAS) was built. The simulated unmanned aircraft system is a T‐shaped structure configured as a horizontal gradiometer with two cesium magnetometers spaced 4.67 m apart, which is the same sensor geometry as planned for the unmanned aircraft system. The simulated unmanned aircraft system is flown suspended beneath a helicopter. An 8.5 km² area in the Central Metasedimentary Belt of the Grenville Province, near Plevna, Ontario, Canada, was surveyed with the simulated unmanned aircraft system suspended 50 m above ground. The survey site was chosen on the basis of its complex geological structure. The total magnetic intensity (TMI) data recorded were compared to that obtained during a conventional fixed‐wing survey and a ground survey. Transverse magneto‐gradiometric data were also recorded by the simulated unmanned aircraft system. The simulated unmanned aircraft system total magnetic intensity data have a higher resolution than the conventional fixed‐wing data and were found to have a similar resolution to that of the ground survey data. The advantages of surveying with the simulated unmanned aircraft system were: (1) the acquisition of a detailed data set free of gaps in coverage at a low altitude above the terrain and (2) substantial saving of time and effort. In the survey site, the 4.67 m simulated unmanned aircraft system gradiometer measured the transverse magnetic gradient reliably up to an altitude of 150 m above ground.     

An automatic approach for rill network extraction to measure rill erosion by terrestrial and low‐cost unmanned aerial vehicle photogrammetry

For an erosion event (October 2016) occurred at the Sparacia experimental area (Southern Italy), both terrestrial and low‐altitude aerial surveys were carried out by consumer grade camera and quadcopter (low‐cost unmanned aerial vehicle [UAV]) to measure rill erosion on two plots with steepness of 22% and 26%. Applying the structure from motion (SfM) technique, the three‐dimensional digital terrain models (3D‐DTMs) and the quasi three‐dimensional models (2.5D‐digital elevation model [DEM]) were obtained by the two surveys. Furthermore, 3D‐DTM and DEM were built using the available aerial photographs (166) and adding 40 terrestrial photographs. For the first time, the convergence index was applied to high‐resolution rill data for extracting the rill network, and a subsequent separation into contributing and non‐contributing rills was carried out. The comparison among the three surveys (terrestrial, UAV, and UAV + terrestrial) was developed using two morphometric parameters of the rill network (drainage density and drainage frequency). Moreover, using as reference the weight of sediment stored on the tanks located downstream of the plots, the reliability of soil loss measurement by 3D models was tested. For both contributing and non‐contributing rills, the morphometric parameters were higher for the terrestrial than for UAV and UAV + terrestrial surveys. For both plots, SfM always provided reliable soil loss measurements, which were affected by errors ranging from ?8% to 13%. Although the applied technique used a low‐cost UAV and a consumer grade camera, the obtained results demonstrated that a reliable estimate of rill erosion can be obtained in an area of interest.     

Application of boat‐based laser scanning for river survey

The boat‐based, mobile mapping system (BoMMS) with a laser scanner allows the derivation of detailed riverine topographical data for fluvial applications. Combined with data acquisition from static terrestrial LiDAR (light detection and range) or mobile terrestrial LiDAR on the ground, boat‐based laser scanning enables a totally new field mapping approach for fluvial studies. The BoMMS approach is an extremely rapid methodology for surveying riverine topography, taking only 85 min to survey a reach approximately 6 km in length. The BoMMS approach also allowed an effective survey angle for deep river banks, which is difficult to achieve with aerial or static terrestrial LiDAR. Further, this paper demonstrates the three‐dimensional mapping of a point‐bar and its detailed morphology. Compared with the BoMMS surface, approximately, 80% and 96% of the terrestrial LiDAR points showed a height deviation of less than 2 cm and 5 cm, respectively, with an overall standard deviation of ± 2·7 cm. This level of accuracy and rapidity of data capture enables the mapping of post‐flood deposition directly after a flood event without an extensive time lag. Additionally, the improved object characterisation may allow for better 3D mapping of the point bar and other riverrine features. However, the shadow effect of the BoMMS survey in point bar mapping should be removed by additional LiDAR data to acquire entire riverine topography. The approach demonstrated allowed a large reach to be surveyed compared with static terrestrial LiDAR and increased the spatial limit of survey towards aerial LiDAR, but it maintains the same or even better temporal resolution as static terrestrial LiDAR. Copyright © 2009 John Wiley & Sons, Ltd.     

From experimental plots to experimental landscapes: topography,erosion and deposition in sub‐humid badlands from Structure‐from‐Motion photogrammetry

In the last decade advances in surveying technology have opened up the possibility of representing topography and monitoring surface changes over experimental plots (<10 m²) in high resolution (~10³ points m^‐1). Yet the representativeness of these small plots is limited. With ‘Structure‐from‐Motion’ (SfM) and ‘Multi‐View Stereo’ (MVS) techniques now becoming part of the geomorphologist's toolkit, there is potential to expand further the scale at which we characterise topography and monitor geomorphic change morphometrically. Moving beyond previous plot‐scale work using Terrestrial Laser Scanning (TLS) surveys, this paper validates robustly a number of SfM‐MVS surveys against total station and extensive TLS data at three nested scales: plots (<30 m²) within a small catchment (4710 m²) within an eroding marl badland landscape (~1 km²). SfM surveys from a number of platforms are evaluated based on: (i) topography; (ii) sub‐grid roughness; and (iii) change‐detection capabilities at an annual scale. Oblique ground‐based images can provide a high‐quality surface equivalent to TLS at the plot scale, but become unreliable over larger areas of complex terrain. Degradation of surface quality with range is observed clearly for SfM models derived from aerial imagery. Recently modelled ‘doming’ effects from the use of vertical imagery are proven empirically as a piloted gyrocopter survey at 50m altitude with convergent off‐nadir imagery provided higher quality data than an Unmanned Aerial Vehicle (UAV) flying at the same height and collecting vertical imagery. For soil erosion monitoring, SfM can provide data comparable with TLS only from small survey ranges (~5 m) and is best limited to survey ranges ~10–20 m. Synthesis of these results with existing validation studies shows a clear degradation of root‐mean squared error (RMSE) with survey range, with a median ratio between RMSE and survey range of 1:639, and highlights the effect of the validation method (e.g. point‐cloud or raster‐based) on the estimated quality. Copyright © 2015 John Wiley & Sons, Ltd.     

High-resolution unmanned aerial vehicle aeromagnetic surveys for mineral exploration targets

Recent advancements in geophysical exploration have been realized through reliably integrating unmanned aerial vehicle platforms with lightweight, high-resolution magnetometer payloads. Unmanned aerial vehicle aeromagnetic surveys can provide a contemporary data product between the two end-members of coverage and resolution attained using manned airborne and terrestrial magnetic surveys. This new data product is achievable because unmanned aerial vehicle platforms can safely traverse with magnetometer payloads at flight elevations closer to ground targets than manned airborne surveys, while also delivering an increased coverage rate compared to walking conventional terrestrial surveys. This is a promising new development for geophysical and mineral exploration applications, especially in variable terrains. A three-dimensional unmanned aerial vehicle aeromagnetic survey was conducted within the Shebandowan Greenstone Belt, northwest of Thunder Bay, Ontario, Canada, in July 2017. A series of two-dimensional grids (∼500 m × 700 m) were flown at approximate elevations of 35, 45 and 70 m above ground level using a Dà-Jiāng Innovations multi-rotor unmanned aerial vehicle (S900) and a GEM Systems, Inc., Potassium Vapour Magnetometer (GSMP-35U). In total, over 48 line-km of unmanned aerial vehicle aeromagnetic data were flown with a line spacing of 25 m. The collected aeromagnetic data were compared to a regional heliborne aeromagnetic survey flown at an elevation of approximately 85 m above the terrain, with a line spacing of 100 m, as well as a follow-up terrestrial magnetic survey. The first vertical derivative of the gathered unmanned aerial vehicle total magnetic field data was calculated both directly between each of the different flight elevations, and indirectly by calculating the values predicted using upward continuation. This case study demonstrates that low flight elevation unmanned aerial vehicle aeromagnetic surveys can reliably collect industry standard total magnetic field measurements at an increased resolution when compared to manned airborne magnetic surveys. The enhanced interpretation potential provided by this approach also aided in delineating structural controls and hydrothermal fluid migration pathways (a pair of adjacent shear zones) related to gold mineralization on site. These structural features were not clearly resolved in the regional manned airborne magnetic data alone, further demonstrating the utility of applying high-resolution unmanned aerial vehicle aeromagnetic surveys to mineral exploration applications. The conclusions and interpretations drawn from the unmanned aerial vehicle aeromagnetic data, coupled with historical data, were applied to make a new gold mineralization discovery on the site, assayed at 15.7 g/t.     

Membrane Interface Probe Protocol for Contaminants in Low‐Permeability Zones

Accurate characterization of contaminant mass in zones of low hydraulic conductivity (low k) is essential for site management because this difficult‐to‐treat mass can be a long‐term secondary source. This study developed a protocol for the membrane interface probe (MIP) as a low‐cost, rapid data‐acquisition tool for qualitatively evaluating the location and relative distribution of mass in low‐k zones. MIP operating parameters were varied systematically at high and low concentration locations at a contaminated site to evaluate the impact of the parameters on data quality relative to a detailed adjacent profile of soil concentrations. Evaluation of the relative location of maximum concentrations and the shape of the MIP vs. soil profiles led to a standard operating procedure (SOP) for the MIP to delineate contamination in low‐k zones. This includes recommendations for: (1) preferred detector (ECD for low concentration zones, PID or ECD for higher concentration zones); (2) combining downlogged and uplogged data to reduce carryover; and (3) higher carrier gas flow rate in high concentration zones. Linear regression indicated scatter in all MIP‐to‐soil comparisons, including R² values using the SOP of 0.32 in the low concentration boring and 0.49 in the high concentration boring. In contrast, a control dataset with soil‐to‐soil correlations from borings 1‐m apart exhibited an R² of ≥0.88, highlighting the uncertainty in predicting soil concentrations using MIP data. This study demonstrates that the MIP provides lower‐precision contaminant distribution and heterogeneity data compared to more intensive high‐resolution characterization methods. This is consistent with its use as a complementary screening tool.     

Airborne EM skin depths

Skin depth is an electromagnetic (EM) scale length that provides a measure of the degree of attenuation experienced by a particular frequency of an EM system. As has been discussed in the literature, skin depth is not a complete measure of the depth of investigation, but the two may be related. Frequency‐domain airborne EM systems employ pairs of transmitter and receiver coils that use a frequency range from several hundred hertz to over 100 kHz. For elevated dipoles, both geometrical and frequency‐dependent attenuation of the induced fields must be considered. For airborne EM systems it is possible to define a skin depth based only on the electric field induced by the transmitter. A vertical decay scale length, here defined from the at‐surface position of maximum electric field, enables the same skin‐depth estimate to be obtained for both cases of vertical and horizontal dipolar excitation. Such dipolar skin depths associated with towed‐bird and fixed‐wing airborne systems are studied in relation to frequency, conductivity and sensor elevation. Dipolar skin depths are found to be much smaller than their plane‐wave counterparts except at high frequency (>50 kHz) and in combination with high conductivity. For the majority of airborne systems the influence of altitude on skin depth is highly significant. Dipolar skin depths increase with increasing sensor elevation. Low frequencies display the greatest sensitivity. At low elevation (<40 m), geometrical attenuation dominates the behaviour of the skin depth. The study indicates that typical low‐altitude airborne surveys provide vertically compact assessments of subsurface conductivity, well suited to near‐surface, environmental applications.     

Buckling‐restrained brace using steel mortar planks; performance evaluation as a hysteretic damper

The authors developed a buckling‐restrained brace that enables increased design freedom at both ends of the core plate and strict quality control while providing stable hysteresis characteristics even under high strains. The buckling‐restrained brace can be formed by welding a core plate covered with unbonded material to a pair of mortar‐filled channel steels (steel mortar planks) as a restraining part. The use of this approach enables visual confirmation of the status of the mortar filling and also facilitates standardizing structural members and member‐by‐member quality control. Specimens of a buckling‐restrained brace with different steel mortar plank heights are fabricated to adjust the restraining force, along with specimens with different core plate width‐to‐thickness ratios. The tests were conducted to reveal the hysteretic characteristics of the braces, as well as their cumulative plastic strain energy, elastoplastic properties, and stiffening properties. A performance evaluation formula as well as a buckling‐restrained brace design method using the test results is proposed. Copyright © 2006 John Wiley & Sons, Ltd.     

Real-time compensation of magnetic data acquired by a single-rotor unmanned aircraft system

Two methods for low-altitude calibration of a single-rotor unmanned aircraft system using a real-time compensator are tested: (1) a stationary calibration where the unmanned aircraft system executes manoeuvres while hovering in order to minimize ambient field changes due to the local geology; and (2) an adapted box calibration flown in four orthogonal directions. Both methods use two compensator-specific limits derived from established methods for manned airborne calibration: the lowest frequency used by the compensator for the calibration algorithm and the maximum variation of the ambient magnetic intensity experienced by the unmanned aircraft system during calibration. Prior to flying, the unmanned aircraft system was magnetically characterized using the heading error and fourth difference. Magnetic interference was mitigated by extending the magnetometer-unmanned aircraft system separation distance to 1.7 m, shielding, and demagnetization. The stationary calibration yielded an improvement ratio of 8.595 and a standard deviation of the compensated total magnetic intensity of 0.075 nT (estimated Figure-of-Merit of 3.8 nT). The box calibration also yielded an improvement ratio of 3.989 and a standard deviation of the compensated total magnetic intensity of 0.083 nT (estimated Figure-of-Merit of 4.2 nT). The stationary and box calibration solutions were robust with low cross-correlation indexes (1.090 and 1.048, respectively) when applied to a non-native data set.     

Composition and origin of a lithalsa related to lake‐level recession and Holocene terrestrial emergence,Northwest Territories,Canada

Lithalsas of the Great Slave Lowland, Northwest Territories, occur within fine‐grained glaciolacustrine, lacustrine, and alluvial deposits. Detailed investigations of a lithalsa revealed that it is composed of ice‐rich sediments with ice lenses up to 0.2 m thick below 4 m depth. The observed ice accounted for about 2 m of the 4 m between the top of the lithalsa and adjacent terrain. The ice is isotopically similar to modern surface water, but enriched in δ¹⁸O relative to local precipitation. Total soluble cation concentrations are low in the basal, Shield‐derived and unweathered glaciolacustrine sediments of the lithalsa. Higher concentrations in the overlying Holocene‐aged lacustrine and alluvial deposits may be due to greater ion availability in Holocene surface waters. Increasing Cl^‐ and Na⁺ concentrations in clays at depth likely relate to exclusion and migration of these dissolved ions in pore water during ice lens formation though total soluble cations remain comparatively low. The lithalsa developed 700 to 300 cal yr BP. A conceptual model of lithalsa formation and landscape evolution illustrates that this feature and more than 1800 other lithalsas in the region have developed in association with Holocene terrestrial emergence following lake‐level recession. Copyright © 2017 John Wiley & Sons, Ltd.     

Compared performances of different algorithms for estimating annual nutrient loads discharged by the eutrophic River Loire

Good estimates of pollutant fluxes are required for Earth systems sciences and water quality management. The gradual accumulation of water quality data records over the past few decades has increased the value of these data for examining long‐term trends. On many major rivers, however, infrequent sampling of most pollutants makes flux estimates and their analysis difficult. This paper explores the performance of different methods for estimating nutrient fluxes. The objective is to assess the accuracy (bias) and precision (dispersion) of annual nutrient fluxes based on monthly sampling, which is the frequency with which 80% of French water quality surveys have been carried out since 1971. The study is based on a data set of nutrient concentrations surveyed at high frequency during a 5 year pilot study (1981–85) at the Orléans station in the middle reaches of the River Loire, France. The mean specific fluxes were 641 (nitrate‐N), 96 (total‐P) and 37 kg year⁻¹ km⁻² (orthophosphate‐P). For each year, the data set was then ‘resampled’ by randomly simulating 12 sampling dates. 100 simulated monthly samplings were generated, upon which seven estimation methods were tested. The evaluations indicate that, when concentrations of specific substances in large rivers exhibit seasonal variation, a simple method based on linear interpolation between samples taken at approximately monthly intervals is advocated. With the monthly sampling interval, the precision (confidence level of 95%) of annual nutrient fluxes obtained by the appropriate methods was 13% for nitrates, 20% for total‐P, 26% for orthophosphates, and 34% for particulate‐P. The frequency of water quality surveys required to obtain an annual nutrient flux with 10% precision was around 15 days for nitrate, 10 days for orthophosphate‐P and total‐P, and about 5 days in the case of particulate‐P. Copyright © 2004 John Wiley & Sons, Ltd.     

3‐D shallow‐water seismic survey evaluation and design using the focal‐beam method: a case study offshore Abu Dhabi

For 3‐D shallow‐water seismic surveys offshore Abu Dhabi, imaging the target reflectors requires high resolution. Characterization and monitoring of hydrocarbon reservoirs by seismic amplitude‐versus‐offset techniques demands high pre‐stack amplitude fidelity. In this region, however, it still was not clear how the survey parameters should be chosen to satisfy the required data quality. To answer this question, we applied the focal‐beam method to survey evaluation and design. This subsurface‐ and target‐oriented approach enables quantitative analysis of attributes such as the best achievable resolution and pre‐stack amplitude fidelity at a fixed grid point in the subsurface for a given acquisition geometry at the surface. This method offers an efficient way to optimize the acquisition geometry for maximum resolution and minimum amplitude‐versus‐offset imprint. We applied it to several acquisition geometries in order to understand the effects of survey parameters such as the four spatial sampling intervals and apertures of the template geometry. The results led to a good understanding of the relationship between the survey parameters and the resulting data quality and identification of the survey parameters for reflection imaging and amplitude‐versus‐offset applications.     

Mapping gamma radiation and its uncertainty from weathering products in a Tasmanian landscape with a proximal sensor and random forest kriging

The radionuclides of potassium (⁴⁰ K), uranium (²³⁸U) and thorium (²³²Th) emit from the land surface gamma radiation that is characteristic of the underlying rocks and the distribution of their weathering products in the landscape. We measured the radiation along widely separated transects using a mobile proximal sensor over a 10 000‐ha region of Tasmania. We supplemented the transect data with information from soil and geological maps and dense data from LandSat and SPOT imagery, a digital elevation model and terrain attributes on a grid at 30‐m intervals so as to map the radionuclides. We used a sequence of steps, starting with a spatial bootstrap and random forests to predict emissions across the study area and at sampling points excluded from the bootstrap samples. The predictions at the sampling points were compared with the observed values to obtain residuals, which were then used to krige them at all points on the 30 m grid. We combined the random forest and kriging predictions on the 30‐m grid to obtain our random forest kriging predictions. Repeating the procedure 100 times provided confidence limits on our results and predictions. The resulting maps of the radionuclides accord well with what we know of the soil, lithology and topography of the region from other sources. Alluvial deposits with large amounts of potassium extend from the foot slopes of the Great Western Tiers and along the flood plains of the Meander River, providing evidence of previous widespread weathering and deposition of the material. The fertile Red Ferrosols (roughly equivalent to Ferralic Nitisols in the World reference base (WRB) classification) on the extensive Tertiary basalt plateau emit little gamma radiation as a result of deep weathering and of potassium movement and accumulation down its talus slopes. The maps show the complexity of the region in terms of soil, lithology and terrain, and they show the merits of gamma radiometry for mapping and understanding the distribution of materials in such regions. Copyright © 2013 John Wiley & Sons, Ltd.     

Al survey of Antarctic meteorites

An²⁶Al survey by non-destructive gamma ray spectrometry was conducted as part of the preliminary examination effort for Antarctic meteorites. A total of 220 samples were studied. The majority of the samples were from the Allan Hills area; however, samples from several other sites, including the Yamato Mountains, were studied. Compared to worldwide falls and finds, the Antarctic group shows a clear trend toward lower²⁶Al levels. At leasr 10% of the samples studied were clearly undersaturated in²⁶Al. The frequency of undersaturated samples suggests that terrestrial ages of several hundred thousand years are common among the Antarctic meteorite collection. The absence of samples with extremely low²⁶Al implies that the upper limit for terrestrial ages in the Antarctic is on the order of 1 million years.     

Run‐off processes from mountains to foothills: The role of soil stratigraphy and structure in influencing run‐off characteristics across high to low relief landscapes

The critical zone features that control run‐off generation, specifically at the regional watershed scale, are not well understood. Here, we addressed this knowledge gap by quantitatively and conceptually linking regional watershed‐scale run‐off regimes with critical zone structure and climate gradients across two physiographic provinces in the Southeastern United States. We characterized long‐term (~20 years) discharge and precipitation regimes for 73 watersheds with United States Geological Survey in‐stream gaging stations across the Appalachian Mountain and Piedmont physiographic provinces of North Carolina. Watersheds included in this analysis had <10% developed land and ranged in size from 14.1–4,390 km². Thirty‐four watersheds were located in the Piedmont physiographic province, which is typically classified as a low relief landscape with deep, highly weathered soils and regolith. Thirty‐nine watersheds were located in the Appalachian Mountain physiographic province, which is typically classified as a steeper landscape with highly weathered, but shallower soils and regolith. From the United States Geological Survey daily mean run‐off time series, we calculated annual and seasonal baseflow indices (BFI), minimum, mean, and maximum daily run‐off, and Pearson's correlation coefficients between precipitation and baseflow. Our results showed that Appalachian Mountain watersheds systematically had higher minimum daily flows and BFI values. Piedmont watersheds displayed much larger deviations from mean annual BFI in response to year‐to‐year variability in precipitation. A series of linear regression models between 21 landscape metrics and annual BFIs showed non‐linear and complex terrestrial–hydrological relationships across the two provinces. From these results, we discuss how distinct features of critical zone architecture, with specific focus on soil depth and stratigraphy, may be dominating the regulation of hydrological processes and run‐off regimes across these provinces.     

Transient sediment supply in a high‐altitude Alpine environment evidenced through a 10Be budget of the Etages catchment (French Western Alps)

Although beryllium‐10 (¹⁰Be) concentrations in stream sediments provide useful synoptic views of catchment‐wide erosion rates, little is known on the relative contributions of different sediment supply mechanisms to the acquisition of their initial signature in the headwaters. Here we address this issue by conducting a ¹⁰Be‐budget of detrital materials that characterize the morphogenetic domains representative of high‐altitude environments of the European Alps. We focus on the Etages catchment, located in the Ecrins‐Pelvoux massif (southeast France), and illustrate how in situ ¹⁰Be concentrations can be used for tracing the origin of the sand fraction from the bedload in the trunk stream. The landscape of the Etages catchment is characterized by a geomorphic transient state, high topographic gradients, and a large variety of modern geomorphic domains ranging from glacial environments to scarcely vegetated alluvial plains. Beryllium‐10 concentrations measured in the Etages catchment vary from ~1 × 10⁴ to 4.5 × 10⁵ atoms per gram quartz, while displaying consistent ¹⁰Be signatures within each representative morphogenetic unit. We show that the basic requirements for inferring catchment‐wide denudation from ¹⁰Be concentration measurements are not satisfied in this small, dynamic catchment. However, the distinct ¹⁰Be signature observed for the geomorphic domains can be used as a tracer. We suggest that a terrestrial cosmogenic nuclide (TCN) budget approach provides a valuable tool for the tracing of material origin in basins where the ‘let nature do the averaging’ principles may be violated. Copyright © 2013 John Wiley & Sons, Ltd.     

Use of terrestrial photogrammetry based on structure‐from‐motion for mass balance estimation of a small glacier in the Italian alps

Different high‐resolution techniques can be employed to obtain information about the three‐dimensional (3D) surface of glaciers. This is typically carried out using efficient, but also expensive and logistically demanding, light detection and ranging (LiDAR) technologies, such as airborne scanners and terrestrial laser scanners. Recent technological improvements in the field of image analysis and computer vision have prompted the development of a low‐cost photogrammetric approach, which is referred to as ‘structure‐from‐motion’ (SfM). Combined with dense image‐matching algorithms, this method has become competitive for the production of high‐quality 3D models. However, several issues typical of this approach should be considered for application in glacial environments. In particular, the surface morphology, the different substrata, the occurrence of sharp contrast from solar shadows and the variable distance from the camera positions can negatively affect the image texture, and reduce the possibility of obtaining a reliable point cloud from the images. The objective of this study is to test the structure‐from‐motion multi view stereo (SfM‐MVS) approach in a small debris‐covered glacier located in the eastern Italian Alps, using a consumer‐grade reflex camera and the computer vision‐based software PhotoScan. The quality of the 3D models produced by the SfM‐MVS process was assessed via the comparison with digital terrain models obtained from terrestrial laser scanning (TLS) surveys that were performed at the same epochs. The effect of different terrain gradients and different substrata (debris, snow and firn) was also evaluated in terms of the accuracy of the reconstruction by SfM‐MVS versus TLS. Our results show that the quality of this new photogrammetric approach is similar to the quality of TLS and that point cloud densities are comparable or even higher compared with TLS. However, special care should be taken while planning the SfM survey geometry, to optimize the 3D model quality and spatial coverage. Copyright © 2015 John Wiley & Sons, Ltd.     

Aeromagnetic surveys in the seas around Japan in 1980

Aeromagnetic surveys in the seas around Japan were carried out in 1979 to 1980 by a YS-11 aircraft of the Maritime Safety Agency of Japan using a new type of airborne magnetometer system. The new type of airborne magnetometer system consists of a ring-core type three-component fluxgate magnetometer, an inertial sensing system, a fish-eye camera to measure the true north, an 8-bit microcomputer and a proton magnetometer. The VLF/OMEGA system is used to fix the position of the aircraft. Tracks extended to about 600 nautical miles off the coast of the Japanese islands in the Sea of Japan and the North-West Pacific Ocean. Average spacing between tracks was about 80 miles. The flights were carried out at an altitude of 9500 feet. From the survey results, magnetic charts of the seven geomagnetic elements for 1980 over the sea around Japan were compiled by the method of least squares using a polynomial. Also, the contour charts of secular variation in 1980 were compiled.     

Landscape transformation of an Alpine floodplain influenced by humans: historical analyses from aerial images

Natural floodplains are spatially heterogeneous and dynamic ecosystems but at the same time, a highly endangered landscape feature due to climate change and human impacts such as water storage, flood control and hydropower production. Flow is considered a master variable that shapes channel morphology and the heterogeneity, distribution, and turnover of floodplain habitats. Despite their highly dynamic nature, the relative abundance of different habitat elements (islands, gravel bars) in natural floodplains seems to remain relatively constant over ecological periods and is referred to as the shifting mosaic steady state concept. In this conceptual context, we analysed spatiotemporal changes in relative habitat abundance and channel complexity of an alpine floodplain from its near natural state in 1940 before water abstraction and levee construction until 2007 using historical aerial images. Within the first decades of impairment, the relative abundance of floodplain habitats that depend on flood and flow pulses such as parafluvial channels and islands shifted toward a greater abundance of terrestrial forest and grassland habitats. After 1986, the duration and frequencies of high‐precipitation events (>60 mm 24 h^–1) triggering major, channel‐reworking floods increased substantially and caused a restructuring of the floodplain and decrease in the abundance of more terrestrial habitat types. These results are contrary to expectations of the shifting mosaic steady state concept yet suggest its potential application as an indicator of landscape transformation and human impacts on floodplain ecosystems. Last, the results raise the applied question as to whether an increased frequency of high flow events induced by climate change can contribute to floodplain restoration. Copyright © 2011 John Wiley & Sons, Ltd.