The electromagnetic response of a horizontal electric dipole buried in a multi‐layered earth

The electromagnetic response of a horizontal electric dipole transmitter in the presence of a conductive, layered earth is important in a number of geophysical applications, ranging from controlled‐source audio‐frequency magnetotellurics to borehole geophysics to marine electromagnetics. The problem has been thoroughly studied for more than a century, starting from a dipole resting on the surface of a half‐space and subsequently advancing all the way to a transmitter buried within a stack of anisotropic layers. The solution is still relevant today. For example, it is useful for one‐dimensional modelling and interpretation, as well as to provide background fields for two‐ and three‐dimensional modelling methods such as integral equation or primary–secondary field formulations. This tutorial borrows elements from the many texts and papers on the topic and combines them into what we believe is a helpful guide to performing layered earth electromagnetic field calculations. It is not intended to replace any of the existing work on the subject. However, we have found that this combination of elements is particularly effective in teaching electromagnetic theory and providing a basis for algorithmic development. Readers will be able to calculate electric and magnetic fields at any point in or above the earth, produced by a transmitter at any location. As an illustrative example, we calculate the fields of a dipole buried in a multi‐layered anisotropic earth to demonstrate how the theory that developed in this tutorial can be implemented in practice; we then use the example to examine the diffusion of volume charge density within anisotropic media—a rarely visualised process. The algorithm is internally validated by comparing the response of many thin layers with alternating high and low conductivity values to the theoretically equivalent (yet algorithmically simpler) anisotropic solution, as well as externally validated against an independent algorithm.     

Multi‐transient electromagnetic repeatability experiment over the North Sea Harding field‡

We present results of synthetic time‐lapse and real repeatability multi‐transient electromagnetic surveys over the North Sea Harding field. Using Archie's law to convert porosity and fluid saturation to resistivity we created 3D isotropic models of the reservoir resistivity at different stages of production from the initial state in 1996 through to complete hydrocarbon production by 2016 and, for each stage, we simulated an east‐west transient electromagnetic survey line across Harding. Unconstrained 1D full‐waveform Occam inversions of these synthetic data show that Harding should be detectable and its lateral extent reasonably well‐defined. Resistivity changes caused by hydrocarbon production from initial pre‐production state to production of the oil rim in 2011 are discernible as are significant changes from 2011–2016 during the modelled gas blowdown phase. The 2D repeatability surveys of 2007 and 2008 tied two wells: one on and the other off the structure. Between the two surveys the segment of the field under investigation produced 3.9 million barrels of oil – not enough to generate an observable time‐lapse electromagnetic anomaly with a signal‐to‐noise ratio of 40 dB. Processing of the 2007 and 2008 data included deconvolution for the measured source current and removal of spatially‐correlated noise, which increased the signal‐to‐noise ratio of the recovered impulse responses by about 20 dB and resulted in a normalized root‐mean‐square difference of 3.9% between the data sets. 1D full‐waveform Occam inversions of the real data showed that Harding was detectable and its lateral extent was also reasonably well‐defined. The results indicate that the multi‐transient electromagnetic method is suitable for exploration, appraisal and monitoring hydrocarbon production.     

Effects of the sea floor topography on the 1D inversion of time‐domain marine controlled source electromagnetic data

Time‐domain marine controlled source electromagnetic methods have been used successfully for the detection of resistive targets such as hydrocarbons, gas hydrate, or marine groundwater aquifers. As the application of time‐domain marine controlled source electromagnetic methods increases, surveys in areas with a strong seabed topography are inevitable. In these cases, an important question is whether bathymetry information should be included in the interpretation of the measured electromagnetic field or not. Since multi‐dimensional inversion is still not common in time‐domain marine controlled source electromagnetic methods, bathymetry effects on the 1D inversion of single‐offset and multi‐offset joint inversions of time‐domain controlled source electromagnetic methods data are investigated. We firstly used an adaptive finite element algorithm to calculate the time‐domain controlled source electromagnetic methods responses of 2D resistivity models with seafloor topography. Then, 1D inversions are applied on the synthetic data derived from marine resistivity models, including the topography in order to study the possible topography effects on the 1D interpretation. To evaluate the effects of topography with various steepness, the slope angle of the seabed topography is varied in the synthetic modelling studies for deep water (air interaction is absent or very weak) and shallow water (air interaction is dominant), respectively. Several different patterns of measuring configurations are considered, such as the systems adopting nodal receivers and the bottom‐towed system. According to the modelling results for deep water when air interaction is absent, the 2D topography can distort the measured electric field. The distortion of the data increases gradually with the enlarging of the topography's slope angle. In our test, depending on the configuration, the seabed topography does not affect the 1D interpretation significantly if the slope angle is less or around 10°. However, if the slope angle increases to 30° or more, it is possible that significant artificial layers occur in inversion results and lead to a wrong interpretation. In a shallow water environment with seabed topography, where the air interaction dominates, it is possible to uncover the true subsurface resistivity structure if the water depth for the 1D inversion is properly chosen. In our synthetic modelling, this scheme can always present a satisfactory data fit in the 1D inversion if only one offset is used in the inversion process. However, the determination of the optimal water depth for a multi‐offset joint inversion is challenging due to the various air interaction for different offsets.     

QUANTITATIVE INTERPRETATION OF PULSE EM MEASUREMENTS OVER A WEATHERED KIMBERLITE DIATREME*

The application of pulse EM and MAXMIN II systems in search of a kimberlite diatremes under conducting cover has been demonstrated through a field example. The effectiveness of the PEM system in the search for conductive zones of economic importance and in discrimination against geologic noise such as overburden has been investigated. The transient observation has been transformed to equivalent half-space resistivities at various times. The feasibility of mapping thin conducting overburden using the PEM system has been studied by inverting the transient measurement to the thin infinite horizontal sheet conductance. The PEM measurement is shown to be an economic and effective tool for shallow geoelectric mapping.     

A parallel,scalable and memory efficient inversion code for very large‐scale airborne electromagnetics surveys

Over the past decade the typical size of airborne electromagnetic data sets has been growing rapidly, along with an emerging need for highly accurate modelling. One‐dimensional approximate inversions or data transform techniques have previously been employed for very large‐scale studies of quasi‐layered settings but these techniques fail to provide the consistent accuracy needed by many modern applications such as aquifer and geological mapping, uranium exploration, oil sands and integrated modelling. In these cases the use of more time‐consuming 1D forward and inverse modelling provide the only acceptable solution that is also computationally feasible. When target structures are known to be quasi layered and spatially coherent it is beneficial to incorporate this assumption directly into the inversion. This implies inverting multiple soundings at a time in larger constrained problems, which allows for resolving geological layers that are undetectable using simple independent inversions. Ideally, entire surveys should be inverted at a time in huge constrained problems but poor scaling properties of the underlying algorithms typically make this challenging. Here, we document how we optimized an inversion code for very large‐scale constrained airborne electromagnetic problems. Most importantly, we describe how we solve linear systems using an iterative method that scales linearly with the size of the data set in terms of both solution time and memory consumption. We also describe how we parallelized the core region of the code, in order to obtain almost ideal strong parallel scaling on current 4‐socket shared memory computers. We further show how model parameter uncertainty estimates can be efficiently obtained in linear time and we demonstrate the capabilities of the full implementation by inverting a 3327 line km SkyTEM survey overnight. Performance and scaling properties are discussed based on the timings of the field example and we describe the criteria that must be fulfilled in order to adapt our methodology for similar type problems.     

A scaled experiment for the verification of the SeaBed Logging method

SeaBed Logging (SBL) is an application of the marine controlled source electromagnetic (CSEM) method that is used to directly detect and characterize possible hydrocarbon-bearing prospects. Although the CSEM method has been used by academia for more than three decades, the application as a direct hydrocarbon indicator was first introduced about five years ago. The central idea of SBL is the guiding of electromagnetic energy in thin resistive layers within conductive sediments. Even if it has been well known for a long time that electromagnetic signals can propagate from a conductive region to another via resistive regions such as air or resistive parts of the lithosphere, the application to hydrocarbon exploration has not been developed until recently. This might be due to the uncertainty of getting any significant response from thin resistive layers such as hydrocarbon reservoirs since electromagnetic energy is highly attenuated in conductive sediments. Thus, during the early development phase of the SBL technique, a scaled laboratory experiment was performed to validate if a thin resistive layer (e.g. hydrocarbons) buried within conductive media (e.g. sediments) could be remotely detected by using electric dipoles as sources and receivers. Data from this experiment were compared to a forward modelling code for layered media, and the comparison showed good agreement between experimental and theoretical results. This suggested that thin resistive layers buried in conductive media are detectable due to the guiding of the electromagnetic field within the resistor. The successful results were vital for realizing the application of marine CSEM as a hydrocarbon exploration technique. We here present the results of the first scaled SBL experiment.     

Analysing two‐dimensional effects in central loop transient electromagnetic sounding data using a semi‐synthetic tipper approach

We present a simple and feasible approach to analyse and identify two‐dimensional effects in central loop transient electromagnetic sounding data and the correspondingly derived quasi two‐dimensional conductivity models. The proposed strategy is particularly useful in minimising interpretation errors. It is based on the calculation of a semi‐synthetic transient electromagnetic tipper at each sounding and for each observational transient time point. The semi‐synthetic transient electromagnetic tipper is derived from the measured vertical component of the induced voltage and the synthetically calculated horizontal component. The approach is computationally inexpensive and involves one two‐dimensional forward calculation of an obtained quasi two‐dimensional conductivity section. Based on a synthetic example, we demonstrate that the transient electromagnetic tipper approach is applicable in identifying which transient data points and which corresponding zones in a derived quasi two‐dimensional subsurface model are affected by two‐dimensional inhomogeneities. The one‐dimensional inversion of such data leads to false models. An application of the semi‐synthetic transient electromagnetic tipper to field data from the Azraq basin in Jordan reveals that, in total, eight of 80 investigated soundings are affected by two‐dimensional structures although the field data can be fitted optimally using one‐dimensional inversion techniques. The largest semi‐synthetic tipper response occurs in a 300 m‐wide region around a strong lateral resistivity contrast. The approach is useful for analysing structural features in derived quasi two‐dimensional sections and for qualitatively investigating how these features affect the transient response. To avoid misinterpretation, these identified zones corresponding to large tipper values are excluded from the interpretation of a quasi two‐dimensional conductivity model. Based on the semi‐synthetic study, we also demonstrate that a quantitative interpretation of the horizontal voltage response (e.g. by inversion) is usually not feasible as it requires the exact sensor position to be known. Although a tipper derived purely from field data is useful as a qualitative tool for identifying two‐dimensional distortion effects, it is only feasible if the sensor setup is sufficiently accurate. Our proposed semi‐synthetic transient electromagnetic tipper approach is particularly feasible as an a posteriori approach if no horizontal components are recorded or if the sensor setup in the field is not sufficiently accurate.     

Modelling and straight‐ray tomographic imaging studies of cross‐hole radio‐frequency electromagnetic data for mineral exploration

Radio‐frequency electromagnetic tomography (or radio imaging method) employs radio‐frequency (typically 0.1–10 MHz) electromagnetic wave propagation to delineate the distribution of electric properties between two boreholes. Currently, the straight‐ray imaging method is the primary imaging method for the radio imaging method data acquired for mineral exploration. We carried out synthetic studies using three‐dimensional finite‐element modelling implemented in COMSOL Multiphysics to study the electromagnetic field characteristics and to assess the capability of the straight‐ray imaging method using amplitude and phase data separately. We studied four sets of experiments with models of interest in the mining setting. In the first two experiments, we studied models with perfect conductors in homogeneous backgrounds, which show that the characteristics of the electromagnetic fields depend mainly on the wavelength. When the borehole separations are less than one wavelength, induction effects occur; conductors with simple geometries can be recovered acceptably with amplitude data but are incorrectly imaged on the phase tomogram. When the borehole separations are longer than two wavelengths, radiation effects play a major role. In this case, phase tomography provides images with acceptable quality, whereas amplitude tomography does not provide satisfactory results. The third experiment shows that imaging with both original and reciprocal datasets is somewhat helpful in improving the imaging quality by reducing the impact of noise. In the last experiment, we studied models with conductive zones extended into the borehole plane with different lengths, which were not accurately recovered with amplitude tomography. The experiment implies that it is difficult to determine the extent of a mineralised zone that has been intersected by one of the boreholes. Due to the large variation of the wavelength in the radio‐frequency range, we suggest investigating the local electric properties to select an operating frequency prior to a survey. We conclude that straight‐ray tomography with either amplitude or phase data cannot provide high‐quality imaging results. We suggest using more general methods based on full electromagnetic modelling to interpret the data. In circumstances when computational time is critical, we suggest saving time by using either induction methods for borehole separations less than one wavelength or wave‐based methods (only radiation fields are considered) for borehole separation larger than two wavelengths.     

A gradient‐ratio method for the semi‐automatic interpretation of gravity map data sets

The application of semi‐automatic interpretation techniques to potential field data can be of significant assistance to a geophysicist. This paper generalizes the magnetic vertical contact model tilt‐depth method to gravity data using a vertical cylinder and buried sphere models. The method computes the ratio of the vertical to the total horizontal derivative of data and then identifies circular contours within it. Given the radius of the contour and the contour value itself, the depth to the source can be determined. The method is applied both to synthetic and gravity data from South Africa. The Matlab source code can be obtained from the author upon request.     

A comparison of different radiomagnetotelluric data inversion methods for buried waste sites

This study deals with two-dimensional (2D) inversions of synthetic and observed radiomagnetotelluric (RMT) data on typical buried conductive waste sites in Europe, and with the practical aspects of different inversion algorithms. In the inversion calculations, we used smoothing and L2-norm stabilizers and compared the results. The resolution of the geometry of the highly conductive waste site, in particular, was investigated. In the inversion with the L2-norm stabilizer, we used the least-squares solution with singular value decomposition (LSSVD) and conjugate gradient (CG), whereas only the conjugate gradient solver was used in the 2D-inversion with the smoothing stabilizer. The inversion results of the synthetic data showed a better resolution of the geometry of the highly conductive waste site when a L2-norm stabilizer was applied in the inversion; in particular, a better detection of the bottom of the waste deposit was achieved. Additional model studies were carried out using synthetic RMT data in order to investigate the 2D inversion of RMT data observed on a 3D structure; these studies showed that the use of TM mode data yields a better resolution of the structure than joint inversion of TE and TM modes.2D inversions of RMT data on a waste site near Cologne showed that the inversion of the TM mode could resolve well the geometry, especially the bottom of the waste site, if information about the background conductivity structure was available. In this case study, inversion with the L2-norm stabilizer produced a sharper image of the waste site than inversion with the smoothing stabilizer, as indicated also by the inversion study that used synthetic data.     

Three‐dimensional modelling of controlled‐source electromagnetic surveys using an edge finite‐element method with a direct solver

A fully three‐dimensional finite‐element algorithm has been developed for simulating controlled‐source electromagnetic surveys. To exploit the advantages of geometric flexibility, frequency‐domain Maxwell's equations of the secondary electric field were discretised using edge‐based finite elements while the primary field was calculated analytically for a horizontally layered‐earth model. The resulting system of equations for the secondary field was solved using a parallel version of direct solvers. The accuracy of the algorithm was successfully verified by comparisons with integral‐equations and iterative solutions, and the applicability to models containing large conductivity contrasts was verified against published data. The advantages of geometry‐conforming meshes have been demonstrated by comparing different mesh systems to simulate an inclined sheet model. A comparison of the performance between direct and iterative solvers demonstrated the superior efficiency of direct solvers, particularly for multisource problems.     

3D joint inversion of magnetotelluric and airborne tipper data: a case study from the Morrison porphyry Cu–Au–Mo deposit,British Columbia,Canada

Z‐axis tipper electromagnetic and broadband magnetotelluric data were used to determine three‐dimensional electrical resistivity models of the Morrison porphyry Cu–Au–Mo deposit in British Columbia. Z‐axis tipper electromagnetic data are collected with a helicopter, thus allowing rapid surveys with uniform spatial sampling. Ground‐based magnetotelluric surveys can achieve a greater exploration depth than Z‐axis tipper electromagnetic surveys, but data collection is slower and can be limited by difficult terrain. The airborne Z‐axis tipper electromagnetic tipper data and the ground magnetotelluric tipper data show good agreement at the Morrison deposit despite differences in the data collection method, spatial sampling, and collection date. Resistivity models derived from individual inversions of the Z‐axis tipper electromagnetic tipper data and magnetotelluric impedance data contain some similar features, but the Z‐axis tipper electromagnetic model appears to lack resolution below a depth of 1 km, and the magnetotelluric model suffers from non‐uniform and relatively sparse spatial sampling. The joint Z‐axis tipper electromagnetic inversion solves these issues by combining the dense spatial sampling of the airborne Z‐axis tipper electromagnetic technique and the deeper penetration of the lower frequency magnetotelluric data. The resulting joint resistivity model correlates well with the known geology and distribution of alteration at the Morrison deposit. Higher resistivity is associated with the potassic alteration zone and volcanic country rocks, whereas areas of lower resistivity agree with known faults and sedimentary units. The pyrite halo and ≥0.3% Cu zone have the moderate resistivity that is expected of disseminated sulphides. The joint Z‐axis tipper electromagnetic inversion provides an improved resistivity model by enhancing the lateral and depth resolution of resistivity features compared with the individual Z‐axis tipper electromagnetic and magnetotelluric inversions. This case study shows that a joint Z‐axis tipper electromagnetic–magnetotelluric approach effectively images the interpreted mineralised zone at the Morrison deposit and could be beneficial in exploration for disseminated sulphides at other porphyry deposits.     

Multi‐dimensional analyses of the SEAM controlled source electromagnetic data—the story of a blind test of interpretation workflows

Using a subset of the SEG Advanced Modeling Program Phase I controlled‐source electromagnetic data, we apply our standard controlled‐source electromagnetic interpretation workflows to delineate a simulated hydrocarbon reservoir. Experience learned from characterizing such a complicated model offers us an opportunity to refine our workflows to achieve better interpretation quality. The exercise proceeded in a blind test style, where the interpreting geophysicists did not know the true resistivity model until the end of the project. Rather, the interpreters were provided a traditional controlled‐source electromagnetic data package, including electric field measurements, interpreted seismic horizons, and well log data. Based on petrophysical analysis, a background resistivity model was established first. Then, the interpreters started with feasibility studies to establish the recoverability of the prospect and carefully stepped through 1D, 2.5D, and 3D inversions with seismic and well log data integrated at each stage. A high‐resistivity zone is identified with 1D analysis and further characterized with 2.5D inversions. Its lateral distribution is confirmed with a 3D anisotropic inversion. The importance of integrating all available geophysical and petrophysical data to derive more accurate interpretation is demonstrated.     

Electric field data in inductive source electromagnetic surveys

Measurement of the electric field data due to an inductive loop source in a controlled source electromagnetic survey is not common, because electric field data, usually involving grounded electrodes, are expensive to acquire and difficult to interpret. With the recently developed capability of versatile three‐dimensional inversion, we revisit the idea of measuring electric field in a large ground loop survey for mineral exploration. The three‐dimensional modelling and inversion approach helps us quantitatively understand the detectability and recoverability of the proposed survey configuration. Our detectability study using forward modelling shows that the relative anomaly (percentage difference) in electric field does not decay with a lower induction number, but the conventional magnetic field data (dB/dt) does. Our recoverability study examines how much and what kind of information can be extracted from electric field data for the reconstruction of a three‐dimensional model. Synthetic inversions show the following observations. (i) Electric field data are good at locating lateral discontinuity, whereas dB/dt has better depth resolution. (ii) Electric field is less sensitive to the background conductivity and, thus, is prone to misinterpretation because of a bad initial model in inversion. We recommend warm‐starting the electric field inversion with an initial model from a separate dB/dt inversion. (iii) Electric field data may be severely contaminated by near‐surface heterogeneity, but an inversion can recover the deep target concealed by the geologic noise. (iv) Even one line of single‐component electric field data can greatly improve the horizontal resolution in a dB/dt inversion. Finally, we investigate a field dataset of both electric field and dB/dt measurements at a uranium deposit. The field example confirms that the electric field and magnetic field data contain independent information that is crucial in the accurate recovery of subsurface conductivity. Our synthetic and field examples demonstrate the benefit of acquiring electric field data along with magnetic field data in an inductive source survey.     

Pitfalls of 1D inversion of small-loop electromagnetic data for detecting man-made objects

In order to interpret field data from small-loop electromagnetic (EM) instruments with fixed source–receiver separation, 1D inversion method is commonly used due to its efficiency with regard to computation costs. This application of 1D inversion is based on the assumption that small-offset broadband EM signals are insensitive to lateral resistivity variation. However, this assumption can be false when isolated conductive bodies such as man-made objects are embedded in the earth. Thus, we need to clarify the applicability of the 1D inversion method for small-loop EM data. In order to systematically analyze this conventional inversion approach, we developed a 2D EM inversion algorithm and verified this algorithm with a synthetic EM data set. 1D and 2D inversions were applied to synthetic and field EM data sets. The comparison of these inversion results shows that the resistivity distribution of the subsurface constructed by the 1D inversion approach can be distorted when the earth contains man-made objects, because they induce drastic variation of the resistivity distribution. By analyzing the integrated sensitivity of the small-loop EM method, we found that this pitfall of 1D inversion may be caused by the considerable sensitivity of the small-loop EM responses to lateral resistivity variation. However, the application of our 2D inversion algorithm to synthetic and field EM data sets demonstrate that the pitfall of 1D inversion due to man-made objects can be successfully alleviated. Thus, 2D EM inversion is strongly recommended for detecting conductive isolated bodies, such as man-made objects, whereas this approach may not always be essential for interpreting the EM field data.     

An alternative approach in establishing relation between vertical and horizontal gradients of 2D potential field

The relation in which the vertical and horizontal gradients of potential field data measured along a profile across a two‐dimensional source are a Hilbert transform pair is re‐established using complex domain mathematics. In addition, a relation between the measured field and its vertical gradient in terms of a closed‐form formula is also established. The formula is based on hypersingular or Hadamard's finite‐part integral. To estimate the vertical gradient directly from the field data, Linz's algorithm of computing Hadamard's finite‐part integral is implemented. Numerical experiments are conducted on synthetically generated total magnetic intensity data with a mild level of noise contamination. A model of a magnetically polarised vertical thin sheet buried at a finite depth within a non‐magnetic half‐space was considered in generating the synthetic response. The results from numerical experiments on the mildly noise‐contaminated synthetic response are compared with those from using classical Fourier and robust regularised Hilbert transform‐based techniques.     

Float‐transient electromagnetic method: in‐loop transient electromagnetic measurements on Lake Holzmaar,Germany

Lake sediments may serve as archives on paleoclimatic fluctuations, geomagnetic field variations and volcanic activities. Lake Holzmaar in Eifel/Germany is a maar lake and its lacustrine sediments provide paleoclimatic proxy data. Therefore, knowledge about the geometry and, especially, about the thickness of the sediments is very important for determining an optimum drilling location for paleoclimatic studies. We have developed a floating in‐loop transient electromagnetic method field set up (Float‐transient electromagnetic method) with a transmitter and receiver size of 18 × 18 m² and 6 × 6 m² respectively. This special set up enables in‐loop transient electromagnetic method measurements on the surface of freshwater lakes that define the geometry and the thickness of sediments beneath such lakes thus helping to determine optimum drilling locations. Due to the modular design of the new Float‐transient electromagnetic method field set up, this system can be handled by two operators and can easily be transported. Sixteen in‐loop soundings were carried out on the surface of Lake Holzmaar. The transient electromagnetic method data could not be interpreted by conventional 1D inversions because of the 3D distribution of subsurface conductivity caused by the lake's geometry. Three‐dimensional finite element modelling was applied to explain the observed transients and the 3D conductivity distribution beneath the lake was recovered by taking its geometry into account. The 3D interpretation revealed approximately 55 m thick sediments beneath 20 m deep water in the central part of the lake.     

地-井瞬变电磁响应特征数值模拟分析

井中瞬变电磁法(Bore-hole transient electromagnetic method-BHTEM)是指接收线圈在钻井中观测瞬变场响应用以勘查深部矿产资源的勘探方法,其中以地-井(地面激发井中接收)组合方式研究最多、应用最广.本文应用时域有限差分法(FDTD),建立包含薄板导体的均匀半空间二维数学模型,采用线源为激发源,选用Mur吸收边界条件,对矩形回线源在半空间中产生的瞬变电磁场进行数值模拟,计算了低阻板状导体在均质半空间和有低阻覆盖层影响情况下的地-井瞬变电磁异常响应,并对响应的特征及规律进行研究分析,为研究地-井TEM提供参考.     

Fast Imaging of TDEM data based on S-inversion

Fast S-inversion is a method of interpretation of time-domain electromagnetic (TDEM) sounding data using the thin sheet model approach. Within the framework of this method, the electromagnetic (EM) response measured at the surface of the earth at every time delay is matched with that of a thin sheet model. The conductivity change with depth is obtained using the conductance, S, and depth, d, of the equivalent thin sheet. We analyze two different numerical techniques, the differential S-transformation and the regularized S-inversion, to determine the parameters of the thin sheet. The first technique is a direct differential transformation of the observed data into conductance and depth values. It is fast and requires no iterations or starting model. The second technique uses a regularized inversion scheme to fit the measured response with that of a thin sheet. In both techniques, the retrieved conductance values are differentiated with respect to depth to obtain the conductivity change with depth. We apply S-inversion to three-dimensional synthetic data and we successfully locate the local conductors. We also demonstrate a case history by interpreting TDEM data obtained at the Nojima fault zone in Japan. The results clearly indicate the location of the fault zone.     

A new marine controlled‐source electromagnetic receiver with an acoustic telemetry modem and arm‐folding mechanism

We developed a new marine controlled‐source electromagnetic receiver for detecting methane hydrate zones and oil and gas reservoirs on the seafloor, which is not imaged well by seismic reflection surveys. To determine the seafloor structure, the electromagnetic receiver should have low noise, power consumption, clock drift error, and operating costs while being highly reliable. Because no suitable receiver was available in our laboratory, we developed a new marine controlled‐source electromagnetic receiver with these characteristics; the receiver is equipped with acoustic telemetry modem and an arm‐folding mechanism to facilitate deployment and recovering operations. To demonstrate the applicability of our new receiver, we carried out a field experiment offshore of Guangzhou in the South China Sea, where methane hydrates have been discovered. We successfully obtained controlled‐source electromagnetic data along a profile about 13 km long. All six new receivers were recovered, and high‐quality electromagnetic data were obtained. Relatively high apparent resistivity values were detected. The results of the offshore field experiment support the claim that the electromagnetic data obtained using the new receiver are of sufficient quality for the survey target.