Subreflector model depending on elevation for the Tianma 65m Radio Telescope

A subreflector adjustment system for the Tianma 65 m radio telescope, administered by Shanghai Astronomical Observatory, has been installed to compensate for gravitational deformation of the main reflector and the structure supporting the subreflector. The position and attitude of the subreflector are variable in order to improve the efficiency at different elevations. The subreflector model has the goal of improving the antenna's performance. A new fitting formulation which is different from the traditional formulation is proposed to reduce the fitting error in the Y direction. The only difference in the subreflector models of the 65 m radio telescope is the bias of a constant term in the Z direction. We have investigated the effect of movements of the subreflector on the pointing of the antenna. The results of these performance measurements made by moving the antenna in elevation show that the subreflector model can effectively improve the efficiency of the 65 m radio telescope at each elevation. An antenna efficiency of about 60% at the K u band is reached in the whole angular range of elevation.     

大型射电望远镜主反射面调整方法研究

随着毫米波天文学和空间通信的重要性日益提高, 对天线性能提出了越来越高的要求, 而天线性能往往受到其反射器表面精度的限制. 微波全息技术是一种快速有效的检测反射面天线表面轮廓的测量技术. 通过微波全息测量得到天线口径场, 计算天马65m射电望远镜反射面与理想抛物面的偏差. 天马65m射电望远镜的主反射面板是放射状的, 有14圈. 面板的每个角都固定在面板下方促动器的螺栓上进行上下移动, 且相邻面板交点处的拐角共用一个促动器. 采用平面拟合的方法可以计算各块面板拐角处的调整值, 但是同一个促动器会得到4个不同的调整量. 通过平面拟合, 同时以天线照明函数为权重的平差计算方法得到相邻面板拐角的一个平差值, 即天马65m射电望远镜1104个促动器的最佳调整值. 通过多次调整和新算法的应用, 天马65m射电望远镜反射面的面形精度逐渐提高到了0.24mm.     

Research on the panel adjustment method of an active main reflector for a large radio telescope

The surface accuracy of a large parabolic antenna is an important indicator to evaluate the quality of the antenna.It not only directly affects the antenna’s aperture efficiency,thereby determining the shortest wavelength that the antenna can work,but also affects the main lobe width and side lobe structure of the antenna pattern.Microwave holography is an important method for parabolic antenna profile detection.In this article we adopt a new algorithm to adjust the panels for the large radio telescope with an active main reflector through the TM65 m antenna’s aperture phase profile.The panels of the TM65 m radio telescope is in a radial pattern with 14 rings.Each corner of the panel is fixed on the screw of the actuator to move up and down,and the adjacent corners of the four panels share an actuator.We use the method of plane fitting to calculate the adjustment value of every panel’s corner.But one actuator,which simultaneously controls the common corner of the adjacent panels,will have different adjustment values according to the different plane fitting equation based on adjacent panels.In this paper,the adjustment value of the adjacent panels’crosspoints are constrained to be equal to the constraint condition to calculate each actuator’s adjustment value of the TM65 m radio telescope.Through multiple adjustments and application of the new algorithms,the accuracy of the TM65 m antenna reflector profile has been improved from the original 0.28 mm to the current 0.19 mm.     

Active sub-reflector research for a large radio telescope

This paper proposes an active sub-reflector suitable for large radio telescopes, which can compensate both of the deformation of the main reflector and sub-reflector position offsets. The mathematical formula of the main reflector deformation compensated by the sub-reflector is deduced based on Cassegrain and Gregory antenna structures. The position of the sub-reflector is adjustable to compensate for defocusing errors on high and low elevations, which are mainly caused by the deformation of the sub-reflector supporting legs. In this paper, the method of obtaining the optimum position of the sub-reflector from the aperture phase by the interferometric method is introduced. The actual measurement is verified on the Tianma 65 m radio telescope, which provides a new way to diagnose the position error of the sub-reflector.     

大口径射电望远镜主面误差分析与修正

建立了40 m口径射电望远镜天线结构有限元模型,依据模型分析结果,对40 m口径射电望远镜天线主面误差进行了分析和数值计算;从误差修正的角度,分别对主面误差的最佳拟合修正、安装角预调的工作仰角综合修正进行了分析与数值计算．误差修正后的计算结果表明,主面精度得到了大幅度的提高．分析结果为该望远镜天线的实际建造提供了参考．     

Correction Method of Antenna Pointing Error Caused by the Main Reflector Deformation

The pointing accuracy of a radio telescope is usually less than one-tenth of its antenna beam width. For large-aperture antennas at the short-centimeter band or millimeter-wave band, the pointing accuracy must be as high as several arc seconds. Therefore, for large-diameter and high-frequency reflector antennas, the pointing problem has become an important focal point to realize the antenna performance. Among many structural subsystem factors that affect the antenna pointing accuracy, there has been only less study on the factor of main reflector deformation. Based on the structural characteristics of the antenna, a reflector space coordinate system is established in this paper. And based on the space coordinates of the main reflector surface points after deformation, a non-linear least squares fitting method with 3 degrees of freedom is proposed to accurately predict the antenna pointing. Finally, the space geometric relationship is used to strictly derive the precise adjustments on the elevation and azimuth in order for correcting the antenna pointing error, and the indirect relationship between the main reflector deformation and the pointing error is constructed. This has certain guiding significance for improving the pointing accuracy of large radio antennas.     

A Study of the Fitting Accuracy of the Active Reflector for a Large Spherical Radio Telescope

We propose a spatial three-degree-of-freedom (DOF) parallel mechanism combining two degrees of rotations and one degree of translation to support the active reflector units of a large spherical radio telescope. The kinematics, workspace and accuracy of the mechanism are analyzed. One-dimensional and two-dimensional fitting errors to the working region of active reflector are investigated. Dimensional parameters of the mechanism and active reflector unit are examined with respect to the requirement of fitting accuracy. The result of accuracy analysis shows the effectiveness and feasibility of the proposed mechanism, and gives a design rule to guarantee the highest working frequency required by large radio telescope.     

射电天文中焦面阵或多波束馈源的应用

焦面阵技术或者多波束馈源系统已经日益广泛地应用于现代射电望远镜，因为它可以充分地利用同一射电望远镜反射面所能提供的信息，在观测比射电望远镜方向瓣大得多的展源时数倍乃至数十倍地提高观测的速度；当存在大气层或电离层的起伏或不均匀影响观测成像质量时，可消除这种影响，提高观测质量；利用焦面阵各单个馈源接收到的信息的互相关，则可以实时监控射电望远镜的反射面、二次反射面、指向精度，从而降低地面上大射电望远镜或空间射电望远镜的精度要求和造价。目前焦面阵已经愈来愈广泛地配置在毫米波射电望远镜和大型射电望远镜的主要波段。对此作了一个较新和全面的评述，对焦面阵应用中的限制，包括相位误差的限制和性能价格比的考虑和可能的前景作了简要的介绍。还分析了在计划中的大型主动球反射面射电望远镜（即FAST）上，配置焦面阵的相应限制、问题和难点，提出了初步的建议，并给出经中英双方讨论后初步拟定的FAST频段、波束及低噪声放大器的配置。     

Suggested quasi-Cassegrain system for multi-beam observation of FAST

FAST, the largest single-dish radio telescope in the world, has a 500-meter diameter main reflector and a 300-meter diameter illuminated area. It has a main reflector that can vary its shape, which continuously changes the shape of the illuminated area in reflector into a paraboloid. In this article, we propose a quasiCassegrain system for FAST. The detailed design results are provided. Such a quasi-Cassegrain system only needs to add a 14.6-meter diameter secondary reflector, which is close to the size of the feed cabin. The distance from the secondary reflector to the focus is only 5.08 m, and it has excellent image quality. In this quasi-Cassegrain system, the shape of the illuminated area in the main reflector continuously changes into an optimized hyperboloid. Using this quasi-Cassegrain system from frequency 0.5 GHz to 8 GHz, the multi-beam system can include 7 to 217 feeds. If this system is used in combination with Phased Array Feed(PAF) technology, more multi-beam feeds or a higher working frequency can be used.     

FAST单元面板面型检测算法研究

500 m口径球面射电望远镜(Five-hundred-meter Aperture Spherical Radio Telescope,FAST)是一个超大口径的可动望远镜,有三项技术创新,一是选址,二是轻型馈源索支撑,三是主动反射面。在主动反射面上,单元面板的面型和面板的出厂加工精度对电磁波在反射面的汇聚有很大影响。FAST主反射面由4 600块三角形反射面板拼接而成,每块面板为边长11 m三角形,这对FAST反射面面板的测量技术提出了更高的要求。摄影测量直接在影像上进行量测,无需接触物体本身;所摄影像信息丰富,可以从中获得所研究物体的大量几何信息和物理信息;适用于大范围、多目标测量,效率高。目前世界上最大的射电望远镜,如GBT和ARECIBO都是采用摄影测量技术进行反射面面形检测。在对现有的面型检测技术调研并试验后,提出基于数字近景摄影测量的方法,对FAST反射面11 m单元面板的面型进行检测,数分钟完成反射面板面型的一次检测,测量精度达到2.5 mm,经过调整后的单元面板的面型精度达到了3.0 mm,结果表明摄影测量应用于FAST反射面单元面板面型检测是可行的。     

A new calibration model for pointing a radio telescope that considers nonlinear errors in the azimuth axis

A new calibration model of a radio telescope that includes pointing error is presented, which considers nonlinear errors in the azimuth axis. For a large radio telescope, in particular for a telescope with a turntable, it is difficult to correct pointing errors using a traditional linear calibration model, because errors produced by the wheel-on-rail or center bearing structures are generally nonlinear. Fourier expansion is made for the oblique error and parameters describing the inclination direction along the azimuth axis based on the linear calibration model, and a new calibration model for pointing is derived. The new pointing model is applied to the 40 m radio telescope administered by Yunnan Observatories, which is a telescope that uses a turntable. The results show that this model can significantly reduce the residual systematic errors due to nonlinearity in the azimuth axis compared with the linear model.     

FAST在深空探测中的应用前景

FAST（Five hundred meters Aperture Spherical Telescope)拟利用贵州省的喀斯特洼地，建立世界上最大的500米口径的球面射电望远镜。主动反射面新概念的提出，实现了望远镜的宽频带和全偏振能力；馈源及支撑系统简化的方案，使FAST对天体和航天器的跟踪范围得到很大的补充。分析预研中的FAST的测控功能，并论证其在未来深空网（DSN）中的重要作用和地位及开展国际合作的可能性。     

Polarization comparison between on-axis and off-axis dual reflector telescopes: Zemax and Grasp8 simulations

The cross-polarization performance for an off-axis dual reflector telescope is shown to be equivalent to an on-axis telescope when used for a large-format focal plane array. The need for low sidelobes forces the on-axis designs to high curvature, which in turn leads to high cross-polarization at the edge of the field. A scheme for correcting instrumental-polarization is presented, as well as a full design for a polarization-pure optical system capable of supporting a 1000-element focal plane array.     

From KARST to FAST: The Conceptual Origin of FAST and Its Decision-making Process

In the era of big science, the construction of large science projects is becoming more complex. Designers have to comprehensively consider factors such as instrument performance, technical reserves, funding, risks, and the environment to make a reasonable decision. On the basis of domestic and international astronomy, this paper sorts out the process of the formation of the Five-hundred-meter Aperture Spherical radio Telescope (FAST) concept and the decisions made by the FAST team, including the Chinese concept of the large telescope, the proposal of the prototype, and the adoption of the active reflector, etc. We also discuss the process of decision-making. FAST was born in the process of interaction and integration between Chinese and international astronomy development, and realized the transformation from following up to taking the lead. It can provide a reference for constructing future large science projects with limited foundations in terms of technology and funding.     

射电望远镜的发展和前景

在近代科学技术发展的基础上诞生和成长起来的射电天文学已经走过了66年的历程,作为射电天文学主要探测工具的射电望远镜有了长足的进步,面临21世纪人类社会和自然科学技术包括天文学发展的挑战,射电望远镜及射电天文学将迈出新的步伐．从射电天文学和射电望远镜发展的关系、射电望远镜几个主要发展方向和目前水平、自90年代以来逐步勾画而明确起来的未来发展方向等方面阐明了射电望远镜的发展和前景,以作为我国发展新一代射电望远镜的参考．     

从KARST到FAST---中国天眼的概念起源与决策过程

在大科学时代,大科学工程的建设日益复杂,设计者需综合考虑设备性能、技术储备、经费、风险、环境等因素才能进行合理决策.在国内外天文学发展的背景中,梳理了500 m口径球面射电望远镜(Five-hundredmeter Aperture Spherical radio Telescope, FAST)概念形成的过程以及FAST团队在其中所做的决策,包括大望远镜中国方案的设想、先导单元的提出、主动反射面技术的采用等,并对决策过程进行了分析探讨. FAST诞生于我国与国际天文学发展的互动与融合进程,实现了从跟进到占据先机的转变,可为在相关基础薄弱的领域建设大科学工程提供参考.     

大口径射电望远镜电磁兼容评估技术研究

电磁兼容性是设备或系统的重要性能指标, 也是保障系统的工作效能和提高系统可靠性的重要因素. 大口径射电望远镜运行阶段, 台址周围无线电业务及内部潜在的电磁干扰会降低观测系统灵敏度、影响天文观测的质量. 本论文针对拟建的新疆110 m全向可动射电望远镜(Qi Tai raido Telescope, QTT)开展了系统电磁兼容评估技术及控制方法研究, 具有重要的工程应用价值. 首先, 依据现有电波环境测量方法的不足, 深入分析了仪器设备的关键参数配置方法及测量时间计算方法, 采用Y因子法校准测量数据, 提出一种准实时电波环境测量方法. 面向高重复性宽带频谱, 分析了宽带频谱信号和噪声特征, 结合标准差理论, 提出一种基于邻值比较的信噪分离方法, 并采用邻值统计方法优化关键参数, 提高信噪分离精度. 针对QTT台址, 开发了自动化电波环境监测系统, 该系统6 GHz以下频段系统增益大于40 dB, 系统噪声系数小于2 dB, 测量不确定度小于1.49 dB, 具有极高的系统灵敏度和测量精度; 分析了频谱监测数据流, 设计了基于HDF5 (Hierarchical Data Format version 5)的数据存储格式, 开发了自动化电波环境测量和监控软件及数据处理软件. 依据QTT台址长期监测数据, 评估分析了台址电磁环境、主要干扰源特征及其影响. 其次, 提出大口径射电望远镜馈源口面干扰电平限值量化方法, 建立了基于台址地形的电波传播模型, 分析了现有电波传播模型的优缺点及适应性, 结合QTT台址实际地形及地质特征, 采用Longley-Rice和Two-Ray电波传播模型, 预测分析了QTT台址潜在干扰区域电磁干扰达到射电望远镜的电波路径衰减, 结合大口径射电望远镜天线增益量化方法, 提出设备所在位置干扰电平限值量化方法, 运用该方法对QTT台址潜在干扰区域的干扰电平限值进行量化. 依据设备所在位置干扰电平限值, 调研分析了国内外军用、民用电磁兼容测量标准, 结合电磁干扰对射电天文观测的影响, 提出一种大口径射电望远镜电磁兼容控制方法, 解决了现有电波暗室测量系统无法直接测量评估电子设备电磁兼容的问题, 该电磁兼容控制方法计划应用于QTT建设及运行阶段, 确保系统拥有良好的电磁兼容性. 最后, 依据QTT台址潜在干扰区域干扰电平限值, 结合典型电子设备电磁辐射频谱, 分析了QTT电磁兼容设计需求, 提出电磁兼容设计初步方案. 另外, 针对台址建筑设施内的中低电磁辐射干扰源, 提出一种低成本建筑屏蔽方法, 应用于QTT台址现有建筑.     

超大口径射电望远镜温度场分析

随着天线口径增大、频率升高,日照热对其性能的影响愈发严重.针对待建的新疆110 m大口径全可动射电望远镜,建立其热分析有限元模型,研究天线在夏至日不同太阳时刻的温度场分布特性.结果如下:一天中,主反射面的最高温度可达42.86℃,出现在14时,同时刻撑腿的温度也达到峰值,为41.74℃.背架水平分区温差在5时、18时、19.5时均超过1℃,会对天线指向性能产生较大影响.夜间天线结构温度分布亦不均匀,俯仰结构的温差明显高于其他构件,最大温差为6.42℃,通过数值模拟与试验相结合的方法,证明了构件的壁厚差异是导致结构夜间温差较大的主要原因.     

A high speed networked signal processing platform for multi-element radio telescopes

A new architecture is presented for a Networked Signal Processing System (NSPS) suitable for handling the real-time signal processing of multi-element radio telescopes. In this system, a multi-element radio telescope is viewed as an application of a multi-sensor, data fusion problem which can be decomposed into a general set of computing and network components for which a practical and scalable architecture is enabled by current technology. The need for such a system arose in the context of an ongoing program for reconfiguring the Ooty Radio Telescope (ORT) as a programmable 264-element array, which will enable several new observing capabilities for large scale surveys on this mature telescope. For this application, it is necessary to manage, route and combine large volumes of data whose real-time collation requires large I/O bandwidths to be sustained. Since these are general requirements of many multi-sensor fusion applications, we first describe the basic architecture of the NSPS in terms of a Fusion Tree before elaborating on its application for the ORT. The paper addresses issues relating to high speed distributed data acquisition, Field Programmable Gate Array (FPGA) based peer-to-peer networks supporting significant on-the fly processing while routing, and providing a last mile interface to a typical commodity network like Gigabit Ethernet. The system is fundamentally a pair of two co-operative networks, among which one is part of a commodity high performance computer cluster and the other is based on Commercial-Off The-Shelf (COTS) technology with support from software/firmware components in the public domain.     

The optical reflector system for the CANGAROO-II imaging atmospheric Cherenkov telescope

A new imaging atmospheric Cherenkov telescope with a light-weight reflector has been constructed. Light, robust, and durable mirror facets of containing carbon fiber reinforced plastic laminates were developed for the telescope. The reflector has a parabolic shape (f/1.1) with a 30 m² surface area, which consists of 60 spherical mirror facets. The image size of each mirror facet is 0°.08 (FWHM) on average. The attitude of each facet can be adjusted by stepping motors. After the first in situ adjustment, a point image of about 0°.14 (FWHM) over 3° field of view was obtained. The effect of gravitational load on the optical system was confirmed to be negligible at the focal plane. The telescope has been in operation with an energy threshold for γ-rays of 300 GeV since May 1999.