A simple experimental method to regain the mechanical behavior of naturally structured marine clays

Quantitative laboratory studies on the structural behavior of natural intact marine clays require a large number of identical natural samples leading to an expensive and challenging task. This study proposes a simple method to reconstruct an artificial structured marine clay as the state of its natural intact clay at both macro and micro levels. For this purpose, the Shanghai marine clay is selected and mixed with low cement contents (1–6%). The clay-cement slurry is mixed in a container with the ice-covered sides at a low temperature about 0 ± 2 °C to postpone the hydration reactions until consolidation began. The purpose of adding cement is to generate the inter-particle bonding and structure in reconstituted samples. Initially, the reconstituted samples are consolidated under the in situ stress of 98 kPa and then under the pre-consolidation pressure of 50 kPa. Mechanical characteristics such as compression index, yield stress, unconfined compression strength, shear strength ratio, and the stress paths from triaxial tests are compared with natural intact clay accordingly. Scanning electron microscope and mercury intrusion porosimetry analyses are also performed to analyze the microstructure of clays for comparison. Furthermore, the proposed method is also examined by using natural intact marine clays of different locations and characteristics.     

Experimental investigation on cyclic deformation behavior of soft marine clay involved principal stress rotation

To investigate cyclic deformation behavior of natural soft marine clay-involved principal stress rotation, a series of undrained tests were conducted by using GDS hollow cylinder apparatus. The principal stress rotates 5000 cycles while the deviator stress was kept at a constant level. The tests results show that the deformation behavior of the tested samples are significantly dependent on cyclic stress ratio (CSR). Furthermore, different type of generation of axial strains occur under different CSRs. With the same CSR, the type of axial strain is different between that considering and ignoring principal stress rotation. When CSR is larger than CSR = 0.42 under principal stress rotation, the axial strain grows rapidly after a few cycles. Compared with the results conducted by cyclic triaxial results, the effect of principal stress rotation on the axial strain is significant.     

Secondary Compression Features of Jiangsu Soft Marine Clay

The results of one-dimensional compression tests conducted on undisturbed specimens of Jiangsu soft marine clay is presented. Because of its high in situ void ratios and natural water content, Jiangsu soft marine clay displays high values of both the virgin compression index, C_c, and the secondary compression coefficient, C_α. The laboratory data indicates that the value of the ratio C_α/C_c for Jiangsu soft marine clay is constant. However, neither C_α nor C_c are constant: they both depend upon the natural water content (or void ratio) and thus are also dependent on the deformation (or compression) of Jiangsu soft marine clay. Settlement analyses show that the secondary settlement of Jiangsu soft marine clay is a significant component of the field settlement. The concept of a constant value for C_α/C_c is used to predict the secondary settlement of a surcharged embankment founded upon Jiangsu soft marine clay. The predictions are in agreement with the limited post-construction field measurements of the embankment settlement.     

Evaluation of the uplift behavior of plate anchor in structured marine clay

The uplift behavior of a plate anchor in a structured clay (soft Ariake clay) is investigated through a series of laboratory tests and method of finite element analysis. The tests are adopted to identify the factors influencing the behavior of the anchor, including the thixotropic nature of Ariake clay, consolidation time, and embedment ratio of the anchor. A finite element method (FEM) is used to analyze and predict the uplift behavior of the anchor plate well in the elastic region and the yield load. The results from both the laboratory tests and the FEM analysis suggest that the embedment ratio for a deep anchor in Ariake clay is close to 4. Further increase in embedment ratio improves the capacity to a lesser extent. FEM overestimates the failure load of the uplift anchor in soft Ariake clay by about 20%. This may be ascribed to the hypothesis in the FEM analysis that there is continuous contact between the clay and the anchor until failure. Vesic’s theory for deep anchors, which may be used to predict the ultimate pullout resistance of the plate anchor in reconstituted Ariake clay, is verified to be applicable. In this paper, the plastic flow zone around the anchor is discussed using FEM which makes the behavior of anchor more understandable during the design stage.     

Rheological characteristics and one-dimensional isotache modelling of marine soft clays

Abstract

This paper presents a novel elasto-viscoplastic constitutive formulation based on the isotache concepts and the Nishihara model. Incorporating a novel viscoelastic body to include the delay elastic deformation of marine soft clays under the external load, the proposed model is used to evaluate the theories of consolidation-creep coupling, strain rate dependency and stress relaxation of saturated marine soft clays, and hence, the methodology used to determine the parameters of the model is discussed. Ningbo marine soft clay is selected as an example to interpret the determination of the model parameters on a field scale. A series of conventional oedometer tests are conducted as well. Eventually, we utilize the model to simulate several kinds of rheological tests, including one-dimensional (1-D) long-term compression tests on Ningbo marine soft clays, 1-D constant rate of strain (CRS) tests on Batiscan clays and 1-D stress relaxation tests on Hong Kong marine deposits. These findings indicate good agreement between the computational and experimental results, suggesting the given model can provide reliable forecasts for the rheological characteristics of marine soft clays.     

Analysis of the experimental compressibility of deep water marine sediments from the Gulf of Guinea

This study strives to analyze the compressibility of deep water marine sediments originating from the Gulf of Guinea. Our approach is multi-scaled and, on the macroscopic level, based on two equations which link the overburden effective stress with the liquidity index, the Biarez & Favre equation on the one hand, and the Burland equation on the other hand (after calculation of the ICL expression as a function of the I_L parameter). On the local level, the evolution of the microstructures is analysed and compared with GoG remoulded clay. Two additional observation techniques have been used, the scanning electron microscope and the mercury intrusion porosimetry.     

Effect of a cement-lignin agent on the shear behavior of Shanghai dredged marine soils

With the rapid urbanization in Shanghai, China, suitable fill materials have been reported to be in great shortage in recent years. A prospective solution to these issues is to convert the huge amount of existing dredged marine soils to construction materials via solidification. However, there have been no studies on the shear behavior of solidified dredged materials from Shanghai region so far, while it has been reported by various researchers that the available data obtained from certain types of clay cannot be confidently and readily applied to other types of soils. To address this challenging issue, in this article, samples of Shanghai marine dredged soils were retrieved from the world’s largest reclamation project in Shanghai Lin-gang New City. A series of laboratory tests have been conducted to investigate the shear behavior of Shanghai dredged marine soils solidified using a new composite curing agent made of cement and lignin. The test results and the effect of this cement–lignin agent on the shear behavior of Shanghai marine soils, including the stress–strain behavior, shear strength properties, and failure characteristics are presented and discussed, which can provide valuable reference for the use of dredged soils as construction materials in the Shanghai region.     

Influence and countermeasure of specimen misalignment to small-strain behavior of soft marine clay

Triaxial test with local displacement transducers is an effective technique to obtain the small-strain stiffness of soils. Many previous studies provided feasible solutions for reducing or avoiding potential sources of error in conventional triaxial tests. However, little literature gave out detailed explanations on how to identify those potential errors from the measured testing data and corresponding solutions. Therefore, nowadays, it is still not easy for a new user to gain proficiency in such kind of advanced tests. In this article, by conducting triaxial tests featured with Hall effect transducer on Shanghai soft marine clay, it is found that the influence of the specimen misalignment to the measured small-strain stiffness cannot be neglected. The typical symptom of specimen misalignment, namely the tilting of specimen, was described carefully. An improved connection between top cap and load cell was applied to overcome the problem. The new connection can reduce the disturbance to specimen in terms of both force and displacement. It can be applied to both isotropic and anisotropic consolidated triaxial tests.     

Variation of temperature-dependent sound velocity in unconsolidated marine sediments: Laboratory measurements

Laboratory measurements of sound velocity in unconsolidated marine sediment were performed to establish specific correction curves between temperature and sound velocity. Cores from the Hupo Basin and the southern sea of Geumo Island were cooled and sound velocity was measured while gradually increasing temperature (from 3 to 30°C). Sediment textural and physical properties (porosity, water content, and bulk density) were measured at the same depth. Sound velocity increases with temperature for clay, mud, silt, and sand sediment, resulting in values of approximately 2.65, 2.72, 2.78, and 3.10?m/s/°C, respectively. These results are similar to those of previous studies, and differences are likely due to density, porosity, and clay contents of the sediment. Using these results, we present correction curves for sound velocity temperature dependence for each sediment texture, which can be used to correct from laboratory to in situ values to develop accurate geoacoustic model.     

A Laboratory model study on the performance of lime pile application for marine soils

In this study, research was conducted to examine the performance of the lime pile application, a deep chemical stabilization method to improve the engineering characteristics of marine soil deposits. By using a laboratory-scale model, the marine soil sample was compacted into soil blocks in circular steel test tanks, with the installation of lime piles in them. An experimental program examined the effect of lime piles on physical and engineering properties of the soil in terms of curing periods and lime pile radial distances. Test results showed that clay fines, linear shrinkage, compressibility, and swelling pressure decreased, while permeability, preconsolidation pressure, and stiffness increased significantly with an increase in curing periods and within a close distance to the lime piles. Also, the electrical resistivity of the treated soils was examined to monitor the changes in their electrical properties. Finally, the correlation between the measured electrical resistivity and swell pressure values of the tested soils at different curing periods suggested that the electrical resistivity values can be used as a monitoring technique for deep chemical treatments of the subsurface soil.     

Anisotropic deformation characteristics of soft marine clay involved the change of b-values and stress direction

In actual engineering, soft clay foundations are in drained or partial drained conditions, it would be useful to establish reasonable constitutive relationship and provide guidance for engineering projects. A hollow cylinder apparatus is used to investigate the anisotropic deformation behavior of natural soft marine clay influenced by intermediate principal stress coefficient b and principal stress direction α. Tests were conducted by maintaining a fixed principal stress direction α relative to the vertical direction, while keeping the intermediate principal stress coefficient b constant. It was found that the anisotropic deformation behavior of natural soft clay is merely influenced by major principal stress direction α, but significantly influenced by intermediate principal stress coefficient b.     

On the compression behavior of remolded cement-admixed soft clay

Although extensive research has been performed on the mechanical properties of cement-stabilized clays, quite a few attempts have been made on the compression behavior of remolded cement-admixed clays. The results from oedometer tests have been discussed to investigate the compressibility of remolded cement-admixed clays, taking into consideration cement amount and curing time. The findings show that the difference in shape and position of compression curves is attributed to cement amount and curing time. Most compression index (C_c) values of remolded cement-admixed clays are greater than those of untreated clay due to the presence of remolded yield stress σ′_yr that is closely related to initial water content and clay fabric. Based on the obtained test data, the relationships of C_c vs. e₀, C_c vs. w₀, C_c vs. e₁, C_c vs. e_yr, and σ′_yr vs. e_yr are preliminarily discussed and quantitatively established. Especially, an important divergence of void index I_v at effective stress σ′_v less than remolded yield stress σ′_yr can be observed at different cement amounts and curing durations. Being independent on cement amount, curing time, and initial state of soil, an excellent convergence occurs at stress σ′_v greater than yield stress σ′_yr. The normalized compression curves of I_v vs. σ′_v at σ′_v?>?σ′_y can be expressed by a unique line that agrees well with intrinsic compression line (ICL) and extended ICL.     

Effects of frequency and confining pressure on consolidation drainage behavior of soft marine clays

Abstract

This article presents an experimental investigation on the dynamic consolidation (DC) drainage behavior of soft marine clays. A sinusoidal harmonic load with different frequencies was applied to simulate the DC method in which the conventional impact load was replaced by the cyclic load. Four geotextile-filter strips were used to form the side drainage channels simulating the wick drain method. A series of loading tests were conducted on soft soil specimens at different confining pressures (i.e., 20, 40, 70, and 100?kPa) and different vibration frequencies (i.e., 0, 0.5, 1, 1.5, 2, and 5?Hz). Test results showed that both confining pressure and frequency have significant influences on the drainage behavior of soft marine clay specimens. The magnitude of drainage volume consistently decreases linearly with increasing confining pressure. Compared to static loading condition, specimens under cyclic loading condition at different frequencies show a better drainage performance. Specimen at applied frequency of 1?Hz exhibits the maximum cumulative drainage volume due to the resonant effect.     

Enhancing the mechanical properties of marine clay using cement solidification

Abstract

The use of soft clay and dredged marine clays as the construction material is challenging. This is because the high water content, high compressibility and low permeability of the clay causing the instability of ground and structure. This detrimental effect of soft clay can be improved by the cement solidification process, which is relatively cheap and efficient. This paper mainly focuses on the study of improvement on the mechanical behavior of cement mixed marine clay. The soil is reconstituted by using ordinary Portland cement of 5%, 10%, 15% and 20% by its mass. The study reveals that cementation of clay significantly improves the peak and residual strength of soil. Similarly, the primary yield stress of the soil is also improved from 16 to 275?kPa as cement content increases from 5% to 20%, respectively. By using statistical tools, the relationships between various parameters are established, which are very important to define the mechanical behavior of the clay. This study reveals that the yield surface of the solidified marine clay is not a smooth elliptical surface. Rather it is composed of two linear surfaces followed by a log-linear surface which can be modeled by using simple parameters obtained from triaxial tests.     

Evaluating the stiffness of chemically stabilized marine clay

Cement-stabilized clay is widely used in soft clay improvement for deep excavation, underground construction, and land reclamation. This paper presents a study on the evaluation of elastic modulus for cement-stabilized marine clay. First, two types of cement-stabilized soils were studied through isotropic compression tests and cylinder split tensile tests. Specimens with different mix ratios and curing periods were used. Stress–strain behavior under isotropic compression was discussed, followed by an introduction and estimation of the stress-free bulk modulus. Empirical correlations between elastic moduli and functions for estimating elastic moduli were then proposed. Further estimation of elastic modulus was conducted with another data set. The results showed that the proposed function for estimating elastic modulus is effective for cement-improved marine clay. Finally, the proposed method and empirical functions were validated with other types of cement-stabilized clay.     

Dynamic characteristics of marine soft clay under variable phase difference and initial static shear stress

Abstract

Under seismic loading, the soil layer is subjected to multidirectional cyclic shear stress with different amplitudes and frequencies because of the coupling of multiple shear waves and the soil element within a slope or behind a retaining wall is subjected to initial static shear stress before subjected to cyclic loading. Due to the complexity of seismic loading propagation, a phase difference exists between the initial static shear stress and cyclic shear stress. To investigate the influence of the phase difference and initial static shear stress on cyclic shear strain, cyclic modulus, and cyclic strength, a series of laboratory tests are performed on Wenzhou marine soft clay by multi-directional simple shear system, which can simulate the actual state better by controlling the horizontal cyclic stress in the x and y directions simultaneously. As the phase difference varies from 0° to 90°, the dynamic shear modulus increases and cyclic strain accumulation decreases with an increasing number of cycles. The shear strain increases with the initial shear stress.     

Laboratory and field test study on the improvement of marine clay slurry by in-situ solidification

Abstract

Soil solidification technology can create an artificial hard shell on a soft soil surface but the type and proportion of the curing agent, the construction technology, and the strengthening depth have large influences on the strengthening effect and engineering cost. This study introduces a new technology of soil solidification whereby an artificial hard shell layer is used as a new method to improve the soft ground. For the in-situ solidification technology, the soil and curing agent are mixed well by using a strong stirring machine so that the soil is strengthened rapidly and forms a hard crust. We introduce the key technology of the in-situ soil solidification method and determine the in-situ crust carrying capacity. The indoor experiment on the curing agent proportions is validated with field tests and a vane shear test, static penetration test, and plate loading test are used to evaluate the reinforcement effect. The experimental results show that the in-situ curing technology of dredged fill processing markedly reduced the reinforcement depth range of the soil water content, improved the physical and mechanical indices, and increased the bearing capacity and strength of the artificial hard shell layer, thereby fully meeting the requirements for the bearing capacity of construction machinery.     

Effect of salt on strength development of marine soft clay stabilized with cement-based composites

Abstract

Marine soft clay with a high salt concentration is widely distributed in coastal areas. In this study, cement-based composites consisting of cement, silica fume, plant ash and NaOH were used as a substitute for ordinary Portland cement, and the effect of salt (sodium chloride) on the strength development of clay was investigated by unconfined compressive strength (UCS) testing and scanning electron microscopy (SEM). With the addition of sodium chloride (NaCl), the amount of cementitious materials decreased, and the salt (sodium chloride) was considered to consume the cement-based composites. The consumption effect could be quantitatively evaluated by the consumption index of salt (CIS) and the clay-water/cement ratio hypothesis. The relationship between the CIS and curing period and an UCS prediction model of clay stabilized with cement-based composites with different salt contents and curing times were established. The CIS gradually decreased with increasing curing time and cement-based composites content. The accuracy of the prediction model was evaluated by a comparative analysis between the measured strengths and predicted strengths; the deviation was mostly within 10%. SEM analyses were employed to describe the changes in the microstructure of the specimens and the influencing mechanism of salt on clay stabilized with cement-based composites.     

Effect of angle between initial and cyclic shear stress on behaviors of marine clay

An angle exists between the initial static shear stress and cyclic shear stress when embankment and retaining walls are subjected to cyclic loadings. To investigate the influence of this angle on the dynamic properties of marine soft clay, tests were performed on Wenzhou soft clay. When the angle was varied from 0° to 90°, the shear strain and excess pore pressure decreased as θ increased while increased as θ increased from 120° to 180°. Shear strain developed more rapidly when θ was 120°, 150°, or 180° than that when θ was 0°, 30°, or 60°. These results indicate that the number of cycles to failure at the larger angles was greater than at the smaller angles. When θ was 90°, the strain in the x-axis direction increased as the number of cycles increased. The development of the excess pore pressure associated with specimen failure was different for different cyclic shear stress ratios and shearing angles. The effect of θ on the strain and excess pore pressure increased as the cyclic shear stress ratio increased.