循环荷载作用下合成纤维系缆粘弹塑性应力应变关系

在循环载荷作用下,合成纤维系缆的应力应变关系表现出明显的非线性特性,直接影响系泊缆绳的动力响应。如何针对其在循环载荷作用下的应力应变关系进行准确的定量描述是有关绷紧式系泊系统设计的关键问题。国内外研究者之前的研究不能反映缆绳的载荷历史、蠕变特性以及刚度变化过程,因此提出一个粘弹性粘塑性模型来描述合成纤维系缆的应力应变关系。本模型能够反映合成纤维缆绳的时间变化特性以及在整个加载—卸载过程中的刚度变化。此外,提出了明确的参数确定方法及步骤,基于简单的蠕变实验可以确定模型的各个参数。将两种载荷条件下聚酯缆绳的实验结果与模型结果进行对比,二者吻合较好,证明了模型的有效性和可靠性。本研究对于绷紧式系泊系统的研发和工程应用具有重要意义。     

循环应力下饱和黏土剪切变形特性试验研究

针对饱和重塑黏土,利用土工静力-动力液压三轴-扭转多功能剪切仪,在不固结不排水(UU)条件下进行了应力控制式循环扭剪和竖向-扭转耦合试验,通过对试验结果的对比分析探讨了初始预剪应力和应力反向对应力-应变关系特性的影响,并阐述了不同加荷模式下孔隙水压力发展特性。以此为基础,综合考虑剪切变形和正向偏差变形的共同效应,同时为了能够反映平均残余变形和循环变形的影响,建议了一个综合应变破坏标准的算式。进而通过利用试验数据与目前常用的应变标准比较,表明这种破坏标准具有普遍适用性和较好的稳定性,适用于判定各种应力条件下黏土试样破坏及其强度。     

不均匀波浪荷载作用下海积软黏土的动力特性

为研究饱和海积黏土在均匀与不均匀波浪荷载作用下的循环特性,利用GDS空心圆柱扭剪仪进行了一系列不排水试验,在相同的初始固结状态下,对试样施加不同最大偏应力q_max、最小偏应力q_min的圆形及螺旋形应力路径的轴—扭联合循环载荷。分析了在考虑主应力轴旋转时,这两种不同应力路径的循环应力比R_CS与动应力比δ=q_mim/q_max对循环加载期间土体动力特性的影响。试验结果表明：R_CS与δ的增大均能提升黏土在波浪荷载下的孔压、轴向应变、双幅剪切应变及其速率,同时也能使土体轴向回弹模量与动剪切模量的衰减更严重,且δ的作用效果会随R_CS的增大而增大。当R_CS≤0.05时,土体在循环期间保持为“弹性安定或塑性安定”状态;而当R_CS≥0.06时,土体会处于“疲劳破坏”或“塑性蠕变”状态,其具体形式由R_CS与δ共同决定。土体在循环过程中的轴向回弹模量与动剪切模量近似呈一定比例。     

软黏土中桶形基础竖向循环加载超重力离心模型试验研究

桶形基础越来越广泛应用于海洋油气平台、海上风机、输电塔、防波堤等构筑物,研究其循环承载特性对以上构筑物服役安全性具有重要意义。通过在软黏土中开展单桶循环上拔以及小间距群桶循环上拔和循环下压超重力离心模型试验,发现循环上拔地基破坏模式为整体破坏,裂隙均呈现圆弧形,循环下压呈现渐进式整体破坏模式,下压过程的挤压作用可明显减小桶周泥面高度,导致其承载力降低。模拟双向受荷工况的循环上拔试验在5次加载后荷载弱化系数开始趋于稳定,远早于单向受荷工况;单向和双向受荷工况循环上拔荷载弱化系数残余稳定值分别为0.31和0.32,循环下压荷载弱化系数最小值为0.35,表明不同加载方式竖向循环荷载作用下,此三者大小均可用软黏土地基灵敏度倒数预估。     

Undrained behavior of natural marine clay under cyclic loading

To study the undrained behavior of natural marine clay under cyclic loading, two kinds of stress-controlled cyclic triaxial tests were conducted on natural K₀-consolidated Wenzhou clay. In the Series I tests, samples were cyclically sheared until failure, and the accumulative behavior was studied; based on the results, a suitable cyclic failure criterion is suggested for natural clays. The effect of loading frequency was also investigated, and it was observed that the loading duration t is a key factor in controlling the undrained cyclic behavior. In the Series II tests, cyclic undrained tests followed by strain-controlled monotonic compression tests were carried out, and special attention was given to changes in the undrained strength after cyclic loading. The degradation of the post-cyclic peak strength was affected by the accumulative behavior during cyclic shearing, but the deviatoric stresses at the critical state were nearly constant. Finally, the accumulative behavior of natural clays was simulated using a proposed anisotropic elastic viscoplastic model with a pseudo-static method of equivalent undrained creep, and the results indicate that this equivalent creep simplification is suitable in practice. By taking the apparent overconsolidation after cyclic loading into account, the post-cyclic strength degradation can also be explained by this model.     

Undrained strength behaviour of a cemented marine clay under monotonic and cyclic loading

The paper presents the results of a series of monotonic and cyclic triaxial shear tests carried out to study the influence of the strain effect and load cycles on the undrained shear strength of a cemented marine clay from the East coast of India. The undrained shear strength of Indian coastal marine clay has been established from a detailed shear testing carried out in three phases. Undisturbed soil samples taken out from the seabed were used in the test. In the first part, a comprehensive monotonic shear testing has been carried out under both stress-controlled and strain rate-controlled conditions. In the second phase on identical soil specimen, undrained cyclic shear tests were carried out at various cyclic stress ratios (CSR) and these stress levels are chosen in such a way so that no failure occurred during testing. In the final phase post cyclic monotonic shear testing was conducted to qualitatively evaluate the damage caused by cyclic loading. The monotonic shear test results bring out the influence of cementation that can be detected by the stress-controlled test. The cyclic stress results are analysed in terms of CSR. Further, the results are correlated in terms of stress path.     

Experimental investigation on cyclic deformation behavior of soft marine clay involved principal stress rotation

To investigate cyclic deformation behavior of natural soft marine clay-involved principal stress rotation, a series of undrained tests were conducted by using GDS hollow cylinder apparatus. The principal stress rotates 5000 cycles while the deviator stress was kept at a constant level. The tests results show that the deformation behavior of the tested samples are significantly dependent on cyclic stress ratio (CSR). Furthermore, different type of generation of axial strains occur under different CSRs. With the same CSR, the type of axial strain is different between that considering and ignoring principal stress rotation. When CSR is larger than CSR = 0.42 under principal stress rotation, the axial strain grows rapidly after a few cycles. Compared with the results conducted by cyclic triaxial results, the effect of principal stress rotation on the axial strain is significant.     

Experimental study on wide-shallow composite bucket foundation for offshore wind turbine under cyclic loading

As an appropriate type of foundation for offshore wind turbines (OWTs), wide-shallow composite bucket foundation (WSCBF) is cost-competitive, and it has a unique and special substructure that comprises seven internal rooms arranged in a honeycomb-like structure. In this study, the cyclic behavior of WSCBF for OWTs embedded in saturated clay was investigated using a large-scale model subjected to lateral cyclic loading. The responses of foundation under constant- and various-amplitude cyclic loadings were recorded in terms of displacements, rotations, and bending moments. The variations in stiffness and damping were obtained, and a collaborative bearing mechanical model between the bucket and soil was considered, which was beneficial for improving the stiffness of the whole structure. Accumulative deformation was found to have little effect on the bearing capacity of the foundation. Dynamic analysis in frequency domain was further performed on both moment and rotation data, and the complex, frequency-dependent impedance was also studied.     

Cyclic behavior of natural organic clay under variable confining pressure that match traffic loading conditions

ABSTRACT

One-way cyclic loading is more typical for traffic loading and cyclic triaxial test has been recognized as a useful method for solving many engineering problems. Under traffic loading, the influence of variable confining pressure on cyclic behavior of natural organic clay subjected to cyclic traffic loading is rarely reported in the literature. In this study, a laboratory investigation on undrained cyclic behavior of natural organic clay is presented and conducted by cyclic triaxial apparatus. Tests are conducted by both constant confining pressure and variable confining pressure, to simulate the loading conditions induced by passing vehicles in actual engineering. Different stress levels are also considered in this study. By comparing between the results of constant confining pressure tests and variable confining pressure tests, it shows that the one-way cyclic behavior of organic clay is influenced significantly by variation of confining pressure, in terms of pore water pressure, permanent axial strain and stress–strain hysteretic loops.     

Settlement and Stability Analysis on Soft Clay Under Cyclic Loading

The results of undrained cyclic triaxial tests on three types of clays are collected and a relationship among the accumulated strain, the initial stress state, cyclic stress in the soil, as well as the number of cycles is established based on the experimental data. With this relationship, a procedure is proposed for subsidence and stability analysis on soft clay under the action of cyclic loads.     

复合加载下桶形基础循环承载性能数值分析

作为一种新型基础形式,吸力式桶形基础除了承受海洋平台结构及自身重量等竖向荷载的长期作用之外,往往还遭受波浪等所产生的水平荷载及其力矩等其它荷载分量的瞬时或循环作用。对复合加载模式下软土地基中桶形基础及其结构的循环承载性能尚缺乏合理的分析与计算方法。应用Andersen等对重力式平台基础及地基所建议的分析方法,基于软黏土的循环强度概念,在大型通用有限元分析软件ABAQUS平台上,通过二次开发,将软土的循环强度与Mises屈服准则结合,针对吸力式桶形基础,基于拟静力分析建立了复合加载模式下循环承载性能的计算模型,并与复合加载作用下极限承载性能进行了对比。由此表明,与极限承载力相比,桶形基础的循环承载力显著降低。     

海洋粉质粘土在波浪荷载作用后的不排水抗剪强度衰化特性

通过对南海重塑粉质粘土土样的大量动三轴试验结果分析,得到此种土在波浪荷载作用后不捧水抗剪强度衰化同动载作用引起的动应变幅及平均累积孔压之间的相互关系和预估公式;并通过与超固结土样的静三轴剪切试验结果的比较,发现动、静三轴两种试验结果具有很好的吻合关系。建议可用超固结土样的静三轴剪切试验同时结合部分动三轴试验来预估土样在波浪荷载作用后不排水抗剪强度衰化与平均累积孔压之间的关系。     

Stability analysis of suction bucket foundations under wave cyclic loading and scouring

Suction bucket foundation is a typical type for offshore turbines. Scour caused by wave and current can reduce the stability of foundation and then endanger the whole structure. This paper details a series of suction bucket model tests performed in sand under wave cyclic loading. The model tests investigate the effect of scour on stability of bucket foundation by artificially excavated scour hole around the foundation. It is revealed that the behavior of foundation bearing capacity can be divided into two stages: the initial cyclic stage and the final stage (showing either cyclic stability or cyclic failure). When the wave circulation is stable, the sand on the front and back sides of the foundation is suspected to be liquefied. With the increase in scour depth, the stability of foundation is gradually reduced, the behavior of foundation gradually changes from a state of cyclic stability to cyclic failure, and the number of waves that can be withstood is drastically reduced. Finally, the height of the center of rotation of the suction bucket was observed to descend with the increase in scour depth.     

Experimental study on the settlement of marine deposits of Anzali under cyclic loading by laminar box apparatus

The central Alborz mountain range, located in northern Iran, neighboring the Caspian Sea and where the two Persia and Eurasia plates meet, is known as a seismologically active area. In this regard, investigation of the behavior of saturated sand deposits located in this area may be of particular interest. Saturated sand deposits are subjected to instabilities owing to liquefaction or volume change due to earthquake shakings. A particular type of saturated sand deposits is Anzali sand which is abundant in Anzali port and other cities located in this area in northern Iran. This type of sand is a representative for most sands found in this area, i.e., the southern coastal line of Caspian Sea. This research is solely focused on the volume change behavior of marine deposits of Anzali area, often characterized as Anzali sand, in terms of the settlement of a model footing located on the surface of the sand by the aid of a transparent laminar shear box apparatus. Effects of a number of factors such as the frequency of the cyclic loading, the initial density of the sand, and the sample preparation method have been investigated. Observations indicated that the density index and the frequency of loading which are proportional to the energy of an earthquake have direct effects on the accumulation and amount of the final settlement of Anzali sand.     

Centrifuge modeling of single pile response due to lateral cyclic loading in kaolin clay

In offshore engineering, pile foundations are commonly constructed in marine deposits to support various structures such as offshore platforms. These piles are subjected to lateral cyclic loading due to wind, wave action, and drag load from ships. In this paper, centrifuge model tests are conducted to investigate the response of the existing single piles due to lateral cyclic loading. The cyclic loading was simulated by a hydraulic actuator. It is found that the residual lateral movement and bending strain are induced in the existing pile after each loading–unloading cycle. This is because plastic deformation is induced in the soil surrounding the existing pile during each loading–unloading cycle. By increasing the applied loads during cyclic loading–unloading process, the lateral movements and bending strains induced in the pile head increase simultaneously. As the cyclic loading varies from 10 to 50 kN, the residual pile head movement increases from 40 to 154?mm, and the residual bending strain of the existing pile varies from 100 to 260 με. The ratio of residual to the maximum pile head movements varies from 0.17 to 0.22, while the ratio of residual to the maximum bending strains is in a range of 0.12–0.55.     

Degradation of lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading

Abstract

In this article, the degradation of the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading is studied numerically. A modified kinematic hardening constitutive model is employed to simulate the degradation of soft clay after cyclic loading. The modified model is verified by comparing the numerical simulation results with the results of centrifuge model tests. Furthermore, the modified model is applied to numerical simulations for evaluating the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading. The degradation of the lateral bearing capacity of piles in soft clay after different cyclic displacement levels and different numbers of cycles is investigated. The study reveals that the modified kinematic hardening constitutive model can effectively estimate the cyclic degradation behavior of piles in soft clay subjected to cyclic lateral loading. The degradation of the ultimate lateral bearing capacity progresses slowly with increasing cyclic displacement level for fewer cycles, and the degradation develops significantly at higher levels of cyclic displacement after applying a larger number of cycles.     

Effect of Cyclic Loading Frequency on Undrained Behaviors of Undisturbed Marine Clay

Based on a series of cyclic triaxial tests, the effect of cyclic frequency on the undrained behaviors of undisturbed marine clay is investigated. For a given dynamic stress ratio, the accumulated pore water pressure and dynamic strain increase with the number of cycles. There exists a threshold value for beth the accumulated pore water pressure and dynamic strain, below which the effect of cyclic frequency is very small, but above which the accumulated pore water pressure and dynamic strain increase intensely with the decrease of cyclic frequency for a given number of cycles. The dynamic strength increases with the increase of cyclic frequency, whereas the effect of cyclic frequency on it gradually diminishes to zero when the number of cycles is large enough, and the dynamic strengths at different frequencies tend to the same limiting minimum dynamic strength. The test results demonstrate that the reasons for the frequency effect on the undrained soil behaviors are beth the creep effect induced by the loading rate and the decrease of sample effective confining pressure caused by the accumulated pore water pressure.     

波浪作用下黄河三角洲海底粉土液化特征对比研究

作为一种常见的近海海底灾害地质现象,波致海床液化严重威胁着黄河三角洲地区海底工程设施的安全。粉质海床液化后,海底粉土的结构、物理和力学性质均发生了改变,研究该变化规律尤其是评估液化后海底粉土再次发生液化的可能性具有重要的理论意义和应用价值。本文利用室内动三轴仪对取自黄河三角洲已液化和未液化海底粉土开展了液化试验对比研究,讨论了已液化和未液化海底粉土在孔压增长模式和轴向动应变发展趋势方面的异同,对比分析了二者的液化势。研究结果表明：应变标准比孔压标准更适用于评估黄河三角洲地区海底粉土的液化势;孔压和动应变发展模式均表明与未液化粉土相比,已液化海底粉土再次发生液化的抗力有所提高;已液化和未液化海底粉土归一化孔压比u_d/σ₃与循环加载次数比N/N_f间相关关系可采用双曲线或指数函数模型进行定量化描述;未液化海底粉土的波致液化临界循环应力比约为0.20,已液化海底粉土的临界循环应力比约为0.35。研究成果有助于加深对海底粉土波致液化特性的认识,亦可为循环应力历史影响下的土体力学性质研究提供参考。     

循环荷载下半圆堤整体稳定性计算方法研究

针对圆弧滑动面法已无法准确判断土体强度发生弱化后半圆堤整体稳定性问题,建立基于循环强度结合D-P屈服准则的拟静力有限元模型来分析半圆堤整体稳定性。分析荷载破坏包络线的变化趋势,给出提高半圆堤整体稳定性的工程建议。并在有限元数值分析结果基础上,对变量进行无量纲化,通过优化分析进行非线性拟合归一得出描述半圆堤整体稳定性的极限状态方程。以长江口深水航道治理二期工程为例,结果表明简化计算方法是可靠的,可供工程设计借鉴和使用。     

Experimental study on the cyclic behavior of loose calcareous sand under linear stress paths

Abstract

Hollow cylinder torsional shear tests on loose isotropically and anisotropically consolidated calcareous sand were conducted to investigate the cyclic behavior under three different linear stress paths, including horizontal line, oblique line, and vertical line stress paths, in a coordinate system of the normal stress difference and the horizontal shear stress. The dominant strain components of the isotropically consolidated specimens are affected by the stress paths. With increasing consolidation stress ratio, axial strain gradually becomes the dominant strain component under the three different stress paths. The cyclic strength of the isotropically consolidated specimens under the three different stress paths are almost the same, while for the anisotropically consolidated specimens, the cyclic strengths are strongly affected by the stress paths. These results indicate that conventional cyclic triaxial tests may overestimate cyclic strength in some cases. Irrespective of the stress paths and cyclic stress ratios, the terminal residual excess pore pressure ratio decreases with increasing consolidation stress ratio. Moreover, an empirical equation is proposed to describe the relationship between the normalized shear work and the normalized residual excess pore pressure ratio. The comparative study reveals that the relationship proposed for silica sand is not suitable for the dynamic analyses of calcareous sand.