海上风电嵌岩桩水平抗力影响因素研究

桩基础是我国海上风电工程中应用最为广泛的基础形式,其中嵌岩桩因其施工难度大,承载力高备受关注。与其他类型的桩基础不同,嵌岩桩的水平承载力不仅受到围岩强度的影响,更与其成桩质量与灌浆材料的强度相关。采用有限元方法分析了嵌岩深度、桩基直径与壁厚、桩身倾斜度等多种因素对嵌岩桩水平承载力的影响,提出了确定嵌岩桩水平极限抗力的标准。研究表明：桩与围岩间的灌浆环会先于桩身发生破坏,因此可将灌浆环受拉破坏作为判断嵌岩桩达到水平极限承载力的标准;桩身倾斜度对嵌岩桩的水平极限承载力影响较大,直径和壁厚的增加,均能提高桩基的水平承载力。     

Experimental Study on the Interaction Mechanism of Cap—Pile Group—Soil

Static load tests on pile group with prototype size were carried out in order to study the behavior and the working properties of the cap—pile group—soil interaction in the pile group foundation. The soil resistance under the cap, the pile shaft resistance and the tip resistance were measured by installing various measuring gauges. Based on these test results, the cap—pile group—soil interaction characteristics were analyzed. The regulations of the soil reaction on the cap, the shaft resistance and the tip resistance of pile, the mechanism of load transfer have been discussed with comparison to the result of the single pile tests. The bearing capacity of pile group is greater than the sum of the bearing capacity of the single pile obtained from testing in the same site in pile group foundation in the case presented here.     

A Model Test on the Behavior of a Static Drill Rooted Nodular Pile Under Compression

A static drill rooted nodular pile is a new type of composite pile foundation with high bearing capacity, and mud emissions can be largely reduced using the static drill rooted method. This report presents a model test on the behavior of this composite pile in a test box. The load-displacement response, axial force, skin friction, and mobilized base load are discussed in the report; in particular, the force in the cemented soil was investigated based on the measured data. Moreover, the finite element software ABAQUS was used to help investigate this behavior more thoroughly. It was determined that the function of the cemented soil around the pile shaft was different from that at the enlarged pile base; the stress in the cemented soil around the shaft increased suddenly when nearing the pile base; the ultimate skin friction obtained in the model test was larger than that estimated in the field test; and the relative displacement between the precast nodular pile and the cemented soil could be ignored during the loading process, which corresponded to the result of the field test and demonstrated that the nodular pile and cemented soil act as one entity during the loading process.     

Shaft capacity of pre-bored grouted planted nodular pile under various overburden pressures in dense sand

Abstract

This paper presents the results of a series of model tests performed to study the shaft capacity of pre-bored grouted planted nodular (PGPN) pile in dense sand. The influence of the vertical overburden pressure on the shaft capacity of the PGPN pile is also investigated based on the test results. The test piles were equipped with strain gauges to measure the axial loads during the loading process, moreover, a foam plate was buried beneath pile tip to eliminate the influence of tip resistance on the shaft capacity. Some conclusions can be drawn based on the test results: the peak skin friction of PGPN pile increases with the increase of vertical overburden pressure applied on the foundation soil, while the rate of increase decreases with the increasing overburden pressure; the surface of the pile–soil interface of PGPN pile is relatively rough, and significant dilatant increase in lateral stress occurs during the loading process.     

Field study of set-up effect in open-ended PHC pipe piles

Large-scale field tests were conducted to study set-up effect in open-ended prestressed high-strength concrete pipe piles jacked into stratified soil. Four open-ended prestressed high-strength concrete pipe piles with 13 and 18 m in embedment depth were fully instrumented with fiber Bragg grating sensors and installed. Several restrike dynamic tests were performed on each test pile, with the time interval from 21.5 to 284 hours after installation. Static loading tests (SLTs) were later performed on each test pile at 408 hours after installation to substantiate the dynamic tests. Changes with time in pile bearing capacity and in the shaft and toe resistances were studied based on the results of the pile tests. The development of shaft resistance set-up in different layers was studied in particular. It was found that set-up effect in the shaft resistance is significant and the toe resistance increment was minor. The overall set-up factor of total bearing capacity was found to range from 0.09 to 0.53, and the set-up effect of friction pile is much larger than the end bearing pile. More significant set-up in shaft resistance was observed in fill and alluvium layer. The dimensionless set-up factor A for shaft resistance in marine deposits ranges from 0.5 to 1.43, and it contributes the most to the shaft resistance as the shaft resistance in marine deposits is higher.     

Dynamic response of a large-diameter pile with variable section in layered saturated soil considering construction disturbance effect

ABSTRACT

An analytical solution is developed in this paper to investigate the vertical time-harmonic response of a large-diameter variable-section pile, and it considers the radial inhomogeneity of the surrounding soil caused by construction disturbance. First, the saturated soil surrounding the pile is described by Biot’s poroelastic theory and a series of infinitesimally thin independent layers along the shaft of the pile, and the pile is represented by a variable-section Rayleigh–Love rod. Then, the dynamic equilibrium equations of the soil and pile are solved to obtain an analytical solution for the impedance function at the pile top using the complex stiffness transfer method and impedance function transfer method. Finally, the proposed solution is compared with previous solutions to verify its reliability, and a parameter study is conducted to provide insights into the sensitivity of the vertical dynamic impedance of the pile and velocity response in low-strain integrity testing on defective piles.     

Longitudinal dynamic impedance of a static drill rooted nodular pile embedded in layered soil

The static drill rooted nodular (SDRN) pile is a new type of precast pipe pile with equally spaced nodes distributed along the shaft and wrapped by the surrounding cemented soil. In this paper, the longitudinal dynamic response of the SDRN pile embedded in layered soil is investigated with respect to the complexity of the pile body structure and the pile–soil contact condition. First, the shear complex stiffness transfer model is used to simulate the radial inhomogeneity of the surrounding soil. Then, the governing Equations of the pile–soil system subjected to longitudinal dynamic loading are established. The analytical solution for the dynamic response at the pile head is obtained by the shear complex stiffness transfer method and the impedance function transfer method. The degenerate case of the present solution is compared with the published solution to verify its reliability, and the complex impedance of the SDRN pile is compared with that of the precast pipe pile and the bored pile. Finally, a parametric study is conducted to investigate the influence of pile–soil parameters on the complex impedance at the pile head within the low frequency range concerned in the design of the dynamic foundation.     

Numerical investigations of soil plugging effect inside large-diameter,open-ended wind turbine monopiles driven by vibratory hammers

Abstract

This study established a Couple Eulerian–Lagrange model to simulate monopile vibratory penetration for the investigation of soil plugging effect during high-frequency penetration of monopiles for wind turbine. Simulation analysis is focused particularly on soil plugging effect of a large diameter monopile during vibratory penetration into sand, clay, or layered soil. The results of the numerical simulation show that soil plugging effect is unlikely to occur during monopile penetration into the clay soil, while partial soil plugging may occur during the sand penetration. Penetration resistance at the pile toe is transferred to the radial stress around the pile wall. At a critical point penetration process, internal shaft friction becomes larger than external shaft friction. Moreover, radial pressure factors increase during partial soil plugging effect. For layered soil, the topsoil not only has great influence on the soil plugging effect, but also affects shaft friction in the subsoil during monopile penetration.     

Field and Theoretical Analysis on the Response of Destructive Pile Subjected to Tension Load

Most field tests are carried out using working piles for verification purposes in China, and loading tests are terminated before achieving true pile capacity. In this work, two full-scale destructive loading tests on tension piles instrumented with strain gauges were conducted to capture true pile capacity. The load-displacement response, load transfer, and threshold of the pile-soil relative displacement for fully mobilizing skin resistance in the uplift case were discussed. It was found that the shaft resistance degradation is observed to be along the pile depth with a reduction factor of 0.905 to 0.931, and the thresholds of pile-soil relative displacement for fully mobilizing skin resistance of the tension pile in different soils are found to be in the range 0.67% to 1.34% of the pile diameter. Based on the field test results, a simple softening model was proposed to describe the degradation behavior of skin friction along the pile-soil interface. Further study was conducted to assess the influence of the threshold of pile-soil relative displacement for fully mobilizing skin friction and the reduction factor on the skin friction. As to the analysis of the response of single pile subjected to tension load, a highly effective iterative computer program was developed using the proposed skin friction softening model. Comparisons of the load-settlement response for the well-instrumented tests were given to demonstrate the effectiveness and accuracy of the proposed simple method.     

Field Study on the Behavior of Destructive and Non-Destructive Piles Under Compression

This paper presents a series of full-scale load tests on long bored piles instrumented with strain gauges along the shafts, including eight field tests of piles loaded to failure and one non-destructive pile load test. The load-displacement response, skin friction, end resistance, and the threshold of the pile-soil relative displacement for fully mobilizing skin resistance were discussed. A simple softening model was proposed to describe the degradation behavior of the skin friction along the pile-soil interface and the load-displacement relationship developed at the pile base. It is found that the shaft resistance degradation investigated in the non-destructive load test only occurs at a shallow depth, and the skin friction of deeper soil is not fully developed. However, unlike the results of the non-destructive load tests, the softening is accompanied by a reduction in skin friction and observed to be along the whole pile depth. The thresholds of pile-soil relative displacement for fully mobilizing skin resistances in different soils have been found to be in the range 0.6% to 2.4% of the pile diameter. Moreover, in practical applications, a bilinear model is assumed to be feasible in analyzing the load-settlement relationship developed at the end of non-destructive pile, whereas the load transmission curve of the soils below the pile base corresponds to a softening model in the field tests of piles loaded to failure.     

适用于潮流能电站的新型模块式嵌岩灌注桩基础结构的应用

近年来,潮流能能量转换技术发展迅速,但大型潮流发电机组基础结构方面的研究和应用还并不多见。针对潮流能电站基础结构在抗弯抗剪强度、桩径尺寸方面的特殊要求,结合我国潮流能富集区海底多为浅覆盖层或裸露基岩、且地形复杂的情况,提出了一种新型模块式嵌岩灌注桩基础结构。该基础结构的嵌岩灌注桩通过在桩内布置环形钢板箍和钢筋束来增强抗剪抗弯能力,使其在常规桩径即可满足潮流能电站的支撑要求,减少了对发电水流断面的阻挡;各主体灌注桩可通过横撑、纵撑和斜撑连接构成模块式基础,以适应不同地形条件、不同机组数量和安装方式的要求。新型模块式嵌岩灌注桩基础结构在LHD联合动能公司3.4 MV潮流发电项目中进行了首次应用,获得了良好的使用反馈。     

端承型桩承载力离心模型试验中的粒径效应研究

利用modeling of models的方法研究端承型桩承载力离心模型试验中的粒径效应。在模拟同一原型时,不同桩径的模型桩,桩身压缩性及桩长均不同,导致侧摩阻力发挥机理及程度不同,本文分别探讨了桩端阻力,侧摩阻力及承载力(桩顶荷载)的粒径效应对承载机理和承载特性的影响。结果表明,桩端阻力的粒径效应作用规律与浅基础一致,可以借用浅基础的粒径效应定量评价方法评价端承桩承载力离心模型试验中的粒径效应。侧摩阻力的粒径效应比桩端阻力的粒径效应显著。由于侧摩阻力的影响,相同条件下承载力的粒径效应比桩端阻力有所增强。对于极限桩端阻力和极限承载力,粒径效应均随长径比的增加而减弱。     

Field and Theoretical Study of the Response of Super-Long Bored Pile Subjected to Compressive Load

In this article, two full-scale pile loading tests were conducted to observe the field performance of the super-long bored piles, and a simplified approach for nonlinear analysis of the load-displacement behavior of a single pile was presented. The field tests on piles indicates that, under the maximum test load, more than 70% of the pile top settlement is caused by the compression of pile shaft. For practical purposes, the pile top settlement can be reduced through improving the pile shaft strength. When the load reaches the maximum test load, the proportion of the load carried by the pile tip is approximately 30%. The super-long pile is functioning as an end-bearing friction pile. The skin friction at shallow depth is fully mobilized and decreases from a peak value with increasing load. However, the skin friction of deeper soil is not fully developed due to less relative displacement. Furthermore, a BoxLucas1 model is used to capture the relationship between unit skin friction and pile-soil relative displacement, whereas a hyperbolic model is used to describe the relationship between toe stress and pile base displacement. Based on the BoxLucas1 model and the hyperbolic model, a load transfer method is used to clarify the response of a single pile, and a computational flow chart is developed. The efficiency and accuracy of the present method is verified using the field tests on piles. The proposed simple analytical approach is economical and efficient, resulting in savings in time and cost.     

Hammer's Impact Force on Pile and Pile's Penetration

Methods of energy and momentum conservation, vibration theories, and model tests are employed to research the impact force of a hammer on a pile and the pile's penetration. An analytical formula of impact force of the hammer on pile is obtained. A comparison of results from the three methods finds that the analytical formula proposed by this article conforms well to practical situations. Research results show that if the hammer's impact energy remains unchanged, penetration increases with the increase of hammer weight and cushion stiffness. In addition, the impact force received by the pile head degrades with the increase of hammer weight, but increases with the increase of cushion stiffness. Impact time decreases with the increase of cushion stiffness, but increases with the increase of hammer weight. The model test shows that, when compared with a cotton cloth cushion, an elastic cushion's advantages lie in that the relatively small pile head impact force can achieve significant pile penetration. The cotton cloth is gradually compacted with the increase of blow counts; hence, the impact force the pile head receives tends to increase gradually.     

海上风电单桩基础土相互作用特性影响因素分析

采用有限元软件ABAQUS建立了海上风电单桩基础与土相互作用数值计算模型,将波浪、洋流及风荷载等效成双向对称循环荷载,研究了水平循环荷载作用下不同因素对桩身水平位移、剪力和弯矩的影响规律。研究表明,随着循环荷载比的增加,桩身位移零点和桩身剪力反弯点沿埋深逐渐下移,桩身弯矩最大值点位于浅层土体;不同荷载频率时桩身位移在零点以上变化较大,桩身弯矩随着频率的增加逐渐增大;单向循环荷载作用下桩身位移最大,双向对称循环荷载作用下桩身位移最小;壁厚较小时对桩身水平位移影响较大;在位移零点之上范围内可以考虑设计"上厚下薄"的钢管桩,以减小桩身水平位移;不同桩壁厚时桩身剪力曲线在埋深约6D处出现交点,且泥面处桩身弯矩变化不明显。     

Field Investigations of Two Super-long Steel Pipe Piles in Offshore Areas

A research on super-long piles has been primarily based on cast-in-place bored piles. In this article, field tests associated with selected measuring technologies were conducted on two super-long steel pipe piles in offshore areas to investigate the behaviors and performance of super-long steel pipe piles. The strain along the pile shaft was monitored by adopting the Brillouin optical time domain reflection and fiber Bragg grating techniques. Static load tests were also conducted on two test piles to determine the bearing capacities. In addition, the axial forces, relative displacements between piles and soils and pile shaft resistances were calculated based on the measured strain. According to the results of the static load tests, the ultimate bearing capacities of the two test piles are greater than 15,000 and 15,500 kN. Both of these values meet the design requirements. In addition, the two test piles can be treated as pure friction piles, and the load transfer mechanism and relationships between the pile shafts and relative displacements are also discussed. Finally, recommendations for practical engineering and significant conclusions are presented.     

Numerical analysis of bearing capacity of drilled displacement piles with a screw-shaped shaft in sand

Drilled displacement (DD) piles with a screw-shaped shaft (referred to as DD piles) are installed using a continuous full thread hollow rod (without a displacement body) inserted and advanced in the soil by both a vertical force and a torque. As a type of newly developed pile, current understanding of the bearing mechanism of DD piles is unsatisfactory, which restricts their further applications in engineering. The primary aim of this paper is to study the bearing mechanism of this type of pile using a numerical method. First, a numerical model for calculating the bearing capacity of the DD piles was created and validated by a laboratory test. Then, the effects of the parameters of pile–soil interface, soil strength, and pile geometrical parameters on the bearing mechanism of the DD piles were investigated in parametric studies. The results of parametric studies show that the limit shear stress on the pile–soil interface, the friction angle of surrounding sand, screw pitch, and thread width significantly influence the bearing capacity of the DD piles, whereas the friction coefficient at the pile–soil interface and the thread thickness have little effect. Based on the results of the parametric studies, the failure mechanism of the DD piles under vertical load is analyzed. Finally, an equation for predicting the ultimate bearing capacities of helical piles based on cylindrical shear failure was used for estimating the bearing capacity of the DD piles, and the calculated results were verified with the numerical results.     

Vertical dynamic impedance of large-diameter pile considering its transverse inertia effect and construction disturbance effect

The vertical dynamic impedance of the large-diameter pile is theoretically investigated considering the construction disturbance effect. First, the Rayleigh–Love rode model is introduced to simulate the large-diameter pile with the consideration of its transverse inertia effect. The shear complex stiffness transfer model is proposed to simulate the radial inhomogeneity of the pile surrounding soil caused by the construction disturbance effect. Then, the pile–soil system is divided into finite segments, and the governing equation of the pile–soil system subjected to vertical dynamic loading is established. Following this, the analytical solution of vertical dynamic impedance at the pile head is obtained by means of the shear complex stiffness transfer method and the impedance function transfer method. Based on the present solution, a parametric analysis is conducted to investigate the influence of the transverse inertia effect on the vertical dynamic impedance at the pile head and its relationship with the pile–soil parameters. Finally, comparisons with published solutions are carried out to verify the reliability of the present solution.     

多向不规则波作用下九桩群桩效应试验研究

小尺度群桩应用广泛,一直是学者研究的重点,小尺度有别于大尺度桩柱,由于桩柱周围存在漩涡的脱落,使得受力特性复杂。以往的研究过程中,波浪主要采用单向不规则波浪,并且试验模型多以两桩或三桩组成的群桩结构为主,桩数相对较少。多向不规则波与群桩结构的作用特点有别于单向不规则波且研究较少。通过物理模型试验,针对多向不规则波对于9桩桩排群桩结构的作用进行了研究。首先综合考虑KC1/3数和相对桩径的影响,提出以参数KCLD 1/3数来衡量群桩的效应,并分析了正向力与横向力随着参数KCLD 1/3数和相对桩距的变化关系,研究了群桩中不同桩位桩柱波浪力的变化规律和方向分布宽度对于群桩波浪力的影响。研究结果表明,群桩中各桩的正向力随着方向分布标准差的增大而减小,而横向力在相对桩距较大时随着方向分布标准差的增大而增大,同时群桩中不同位置桩上的波浪力具有较大的差异。     

Neural Network Model for Predicting the Resistance of Driven Piles

Although numerous investigations have been performed over the years to predict the behavior and resistance of piles, the mechanisms are not yet entirely understood. Predicting pile resistance is a difficult task because there are a large number of parameters affecting the capacity that have complex relationships with each other. It is extremely difficult to develop appropriate relationships between various essential parameters, including the soil condition, pile type, driving condition, time effect, and others. This paper describes the application of an artificial neural network (ANN) to predict the resistance of driven piles in dynamic load tests. The training and testing of the ANN were based on 165 data points for driven piles at various construction sites in Korea. Predictions on the tip, shaft, and total pile resistance were made for piles with available corresponding measurements of such values. The effect of the essential parameters on the pile resistance values was investigated through parametric analysis using ANN modeling. The results of this study indicate that the ANN model serves as a reliable and simple predictive tool to appropriately consider various essential parameters for predicting the resistance of driven piles.