氯盐干湿环境下受弯横向裂缝对钢筋混凝土耐久性影响

为了研究持续开裂状态下横向裂缝对钢筋混凝土结构耐久性的影响特性,开展了8根受弯开裂钢筋混凝土梁构件的盐溶液干湿循环试验;借助无损检测技术和破损实测方法,分别对氯离子侵入量、钢筋半电池电位、腐蚀电流密度以及平均锈蚀率等进行了对比分析。研究结果表明,裂缝的存在将提高混凝土的渗透性,裂缝处及周围混凝土内的氯离子含量明显增大;对于一定裂缝分布状况的钢筋混凝土试验梁,内部钢筋的腐蚀电位、腐蚀电流密度以及平均锈蚀率均高于裂缝自愈及无裂缝的试验梁,并受到保护层厚度与裂缝开展状态的影响,其影响规律可用单位长度内的平均裂缝宽度与保护层厚度的比值wm/c来进行综合评价。综合试验结果,初步建议海洋干湿侵蚀环境下钢筋混凝土构件的最大裂缝宽度wmax宜小于0.003 3 c,相关结论可为海洋混凝土结构的耐久性设计提供参考。     

基于人工神经网络的混凝土疲劳寿命估算

把决定混凝土疲劳寿命的应力水平，应力比，加载频率和描述随机性的破坏概率作为神经网络的输入，以疲劳寿命作为网络的输出，用网络结构描述它们之间的非线性关系，利用实验数据样本完成了网络的训练，并对模拟样本进行了估算，实例计算了结果表明，利用已有疲劳试验数据训练好的人工神经网络进行混凝土疲劳寿命估算，可部分代替冗长，昂贵的疲劳实验。     

基于压磁效应的锈胀开裂混凝土梁疲劳性能试验研究

开展了5根锈胀开裂钢筋混凝土梁疲劳试验并实时记录了梁表面的钢筋压磁信号,研究锈胀开裂混凝土梁的疲劳特性和压磁信号演化规律。结果表明梁疲劳寿命随钢筋锈蚀率增大而急剧减小,梁破坏时混凝土剥落,纵筋发生疲劳断裂;磁信号时变曲线随疲劳进程不断演化,在临近疲劳破坏时曲线形态发生明显畸变,能够反映梁疲劳损伤信息;磁感应强度变化幅值的发展符合三阶段特性,在疲劳初期和破坏前增长明显;磁感应强度变化幅值对钢筋锈蚀敏感,随锈蚀率增加而增大,因此建立了疲劳作用不同阶段磁信号幅值和梁内钢筋锈蚀率的相关关系。     

Fatigue Behavior of Plain Concrete Under Biaxial Compression: Experiments and Theoretical Model

The effects of different lateral confinement stress on the fatigue behavior of and cumulative damage to plain concrete are investigated experimentally. Eighty 100 mm x 100 mm x 100 mm specimens of ordinary strength concrete are tested under constant- or variable-amplitude fatigue loading and lateral confinement pressure in two orthogonal directions. A fatigue equation is developed by modifying the classical Aas-Jakobsen S-N equation for taking into account the effect of the confined stress on fatigue strength of plain concrete. The results of variable-amplitude fatigue tests indicate that the linear damage theory proposed by Palmgren and Miner is unreasonable in the biaxial stress state. A nonlinear cumulative damage model that could model the effects of the magnitude and sequence of variable-amplitude fatigue loading and lateral confinement pressure is proposed on the basis of the evolution laws of the residual strains in the longitudinal direction during fatigue tests. The residual fatigue life predic     

Fatigue Properties of Plain Concrete Under Triaxial Compressive Cyclic Loading

Experiments were made on plain concrete subjected to triaxial static loading and constant-amphtude compressive fatigue loading with a constant lateral pressure in two directions. The initial confining pressure was O, O. lfc, O. 25fc and O. 4fc, respectively, for the static test, and O. lfc and O. 25fc for the fatigue test. Based on the triaxial compressive constitutive behavior of concrete, the inflexion of confining pressure evolution was chosen to be the fatigue damage criterion during the test. The rule of evolution of longitudinal maximum and minimum strains, longitudinal cyclic modulus and damage were recorded and analyzed. According to the Fardis-Chen criterion model and the concept of equivalent fatigue life and equivalent stress level, a unified S-N curve for multi-axial compressive fatigue loading was proposed. Thus, the fatigue strength factors for different fatigue loading cases can be obtained. The present investigation provides information for the fatigue design of concrete structures.     

Mechanical test study on corroded marine high performance steel under cyclic loading

It is inevitable that marine structures suffer from corrosion and extreme cyclic loading. In order to study the influence of corrosion damage and cumulative fatigue damage on mechanical properties of marine steel, high performance steel NV-D36 was analyzed under electrochemical corrosion and cyclic loading. It was found that corrosion damage can reduce the elastic modulus, yield strength, ultimate stress and ultimate strain of steel NV-D36. And it was also found that cumulative fatigue damage will increase the ultimate stress of steel NV-D36 and reduce the ultimate strain of steel NV-D36. The effect of double damage on mechanical properties of steel NV-D36 was coupled with these two kinds of damage. The Chaboche model parameters calibrated under incremental cyclic loading scheme can exactly describe the stiffness and peak stress of steel NV-D36.     

Fatigue Behavior of Unbonded Partially Prestressed Concrete Beams with Flexure

A study on fatigue behavior of unbonded partially prestressed concrete beams is presented.Model tests have been carried out in static loading and cyclic compressive loading on 15 beams withflexure.The ratios of the lower limit to the upper limit of fatigue load are 0.5 and 0.3 respectively,and thefrequencies of cyclic loading are 8 Hz and 4.5 Hz respectively.The experimental results of the strains of theconcrete and steel bars,the deflection of test beams,and the crack width of normal section are analyzed.According to statistics and analysis of test results,the corresponding calculation models are developed andpresented.     

FPSO结构低周疲劳寿命计算方法研究

FPSO在海洋环境中频繁地进行装载与卸载操作,使FPSO船体结构产生较大的应力幅值,尤其是承受货油压力的内底纵骨。由于局部的应力集中,应力幅值超过材料的屈服强度,其装卸载次数小于104时,结构将产生低周疲劳。研究一种新的计算方法,根据Neuber假设进行塑性修正,通过应变范围得到伪热点应力范围,并确定热点应力与伪热点应力之间的关系。推导出一种新的S-N曲线作为低周疲劳的设计曲线,以伪热点应力作为计算量来预测低周疲劳寿命,降低了船体结构低周疲劳寿命计算的难度。     

波浪作用下开孔沉箱疲劳与承载能力研究

开孔沉箱孔洞周围存在以三轴循环应力为特征的复杂承载区,其中混凝土损伤速度远大于单轴应力条件,局部疲劳损伤快速累积使结构整体承载能力迅速下降。考虑迎浪面入射波浪与消浪室内反射波浪的循环作用,针对开孔区域复杂应力状态下的疲劳损伤问题,基于不可逆损伤力学发展的数值计算方法模拟开孔板疲劳过程,得到循环荷载作用下不同类型开孔板的损伤演化历程,并计算损伤后整体结构极限承载力大小,通过综合对比孔洞损伤发展规律和结构极限承载能力,建立了疲劳作用下开孔沉箱极限承载能力判断依据。现有规范依据设计使用年限、波浪条件、作用效应组合等确定材料与结构强度,但并未充分体现开孔结构的优势与承载特点,在此基础上文中补充了开孔结构的优化设计以及实际寿命判断。     

An Integrated Approach to Fatigue Life Prediction of Whole System for Offshore Platforms

The failure of one or even more components usually does not lead to the collapse of the whole structure. Most of the analysis of fatigue is centered on only a single component which the researchers are interested in or much attention should be paid to. However, the collapse of a structure is the result of failure of a series of components in a specific order or path. This paper proposes an integrated approach to fatigue life prediction of whole structural system for offshore platforms, mainly describing the basic principles and prediction method. A method is presented for determining the failure path of the whole structure system and calculating the fatigue life in the determined failure path. The corresponding final collapse criteria for the whole structure system are discussed. A simple method of equivalent fatigue stress range calculation and a mathematical model of structural component fatigue life estimation in consideration of sea wave and sea ice loads are provided. As an application of the propo     

基于EIFS和P-M的海底管道腐蚀疲劳寿命预测

鉴于腐蚀疲劳损伤的特殊性,研究了点蚀过程和腐蚀疲劳裂纹扩展过程。基于等效初始缺陷尺寸(EIFS)和线性累积损伤理论(P-M)方法,消除了点蚀形核、蚀坑生长及腐蚀疲劳短裂纹扩展对腐蚀疲劳寿命预测的影响;避免了基于单点蚀坑建立的腐蚀疲劳寿命预测表达式的弊端;合理地简化了随机荷载下腐蚀疲劳寿命的预测流程。利用现有试验数据,对基于EIFS和P-M方法建立的腐蚀疲劳寿命预测表达式进行了模型验证。结果显示,所提模型的有效性和合理性得到了验证,为工程实际中海底管道的腐蚀疲劳寿命预测提供了一种可行方法。     

风、浪荷载作用下海上风机单桩结构灌浆连接段疲劳性能评价

灌浆连接段的疲劳性能对于海上风机单桩支撑结构至关重要。基于385种工况下的某实际5 MW单桩风机支撑结构在风、浪荷载作用下的动力响应分析,获取了灌浆连接段荷载边界条件时程。建立灌浆连接段精细化有限元子模型,将荷载边界条件转化为应力时程。对于剪力键采用"热点应力"方法进行疲劳性能评价。对于灌浆材料,选取剪力键附近灌浆材料单元积分点处的第三主应力进行疲劳性能评价。采用Palmgren-Miner线性损伤累计准则和雨流计数方法进行疲劳损伤的累计。在某实际灌浆连接段20年的设计寿命周期内,最大剪力键总疲劳损伤为1.35×10~(-10);最大灌浆材料总疲劳损伤为1.54×10~(-3)。由此可见,灌浆连接段的疲劳性能由灌浆材料控制,且损伤值远小于限值1/3,在现有的荷载条件下,灌浆连接段不会发生疲劳破坏。分析产生损伤较大的几种工况可知,风速对现有单桩结构灌浆连接段疲劳的损伤起控制作用。     

Durability of Concrete with Different Improvement Measures and Its Service Life Prediction in Island and Reef Environment

To solve the durability of island and reef concrete engineering in the harsh environment of high temperature, high salt, high humidity and windy, the strength grade of concrete and the type of corrosion inhibitor were used as the influence factors, while the relative dynamic elastic modulus was used as the evaluation index. In addition, the law and time variability of the deterioration of concrete, the size effect, environmental similarity and the service life model were studied. The results showed that improving the strength grade of concrete could improve the durability of concrete, and corrosion inhibitor could slightly improve the durability of concrete. Time-varying law of the deterioration of concrete conformed to the univariate quadratic polynomial. Combined with the concrete damage equivalent theory, a size effect model based on the relative dynamic elastic modulus was proposed and verified, and the size effect coefficient was also given. An environmental similarity model between simulated and practical island and reef environment was proposed. Combined with the reliability theory and the first order second moment method, a new service life model of concrete structure was proposed. The authors were convinced that the research will be advantageous to researchers.

     

Probabilistic lifetime assessment of marine reinforced concrete with steel corrosion and cover cracking

In order to study the durability behavior of marine reinforced concrete structure suffering from chloride attack,the structural service life is assumed to be divided into three critical stages,which can be characterized by steel corrosion and cover cracking.For each stage,a calculated model used to predict the lifetime is developed.Based on the definition of durability limit state,a probabilistic lifetime model and its time-dependent reliability analytical method are proposed considering the random natures of influencing factors.Then,the probabilistic lifetime prediction models are applied to a bridge pier located in the Hangzhou Bay with Monte Carlo simulation.It is found that the time to corrosion initiation t0 follows a lognormal distribution,while that the time from corrosion initiation to cover cracking t1 and the time for crack to develop from hairline crack to a limit crack width t2 can be described by Weibull distributions.With the permitted failure probability of 5.0%,it is also observed that the structural durability lifetime mainly depends on the durability life t0 and that the percentage of participation of the life t0 to the total service life grows from 61.5% to 83.6% when the cover thickness increases from 40 mm to 80 mm.Therefore,for any part of the marine RC bridge,the lifetime predictions and maintenance efforts should also be directed toward controlling the stage of corrosion initiation induced by chloride ion.     

模拟海洋大气腐蚀试验方法的研究

本文以不同浓度的天然海水、人造海水和氯化钠溶液对五种钢材进行了试验,结果表明,采用天然海水喷雾模拟性和试验重现性为最佳,腐蚀形态与海洋环境腐蚀结果基本一致·     

Parametric interpolation method for probabilistic fatigue analysis of steel risers

Slender marine structures such as mooring lines and risers are susceptible to failures due to stress variations coming from environmental actions. Wave, wind and current are random phenomena, and consequently the most adequate methodology to estimate the fatigue damage accumulation on these structures is the probabilistic fatigue analysis. In practice, the estimation of fatigue life requires the numerical simulation of a huge number of loading cases to compute the multi-dimensional integral of the total fatigue damage.This paper presents an efficient approach to compute the long-term fatigue damage of marine structures. The proposed method needs only a few number of numerical simulations to estimate the structure fatigue life. It uses a parametric interpolation procedure to evaluate the fatigue damage for any individual short-term condition (sea state) required in the calculation of the multi-dimensional integral. In this way, the total number of short-term structural analyzes is considerably reduced.The effectiveness and accuracy of the proposed method is compared to the full direct integration by means of two comprehensive examples. The first studied case is an idealized theoretical model of a single-degree-of-freedom (SDOF) system under wave loading, and the second one is a Steel Catenary Riser (SCR) connected to a FPSO (Floating, Production, Storage and Offloading floating unit).     

非常规管节点疲劳寿命分析与计算

对非常规管节点的疲劳寿命进行了分析研究，用SESAM计算疲劳载荷，应用精细有限元分析计算热点应力，用规范的S—N曲线计算管节点的疲劳寿命。通过实例计算表明，这些处理对非常规管节点疲劳寿命分析与计算是很有效的。     

The influence of wave-current sea states on the reliability estimates of offshore towers

Since offshore towers are high-cost, high-risk structures, reliability analysis is of great importance in their design. This paper presents a possible practical approach to certify a design through selective critical member reliability estimates. After a brief review of current research in this field, the authors outline a procedure for reliability estimation of structural members in extreme stress and fatigue limit states. A spectral approach for the extreme response statistics with stochastic loading is described. The reliabilities are computed by the Level II first-order second moment (advanced) method. The fatigue reliability is estimated with a narrow-banded stress assumption with discrete, but significant sea states within the life of the structure. Two numerical examples, a three shallow water model and a two-dimensional deep water model are presented along with the influences of stochastic variables (sea state, current, tubular member diameter) on reliabilities (extreme stress and fatigue damage).     

点蚀损伤下桩基式平台腿柱轴压极限承载力研究

采用圆柱体点蚀损伤模型,建立含细观尺度点蚀损伤的桩基式平台腿柱多尺度精细化数值模型,研究壁厚损伤度、点蚀损伤强度以及点蚀体积损伤强度影响平台腿柱轴压极限承载力的规律。研究结果表明,壁厚损伤度及点蚀损伤强度明显削弱平台腿柱的极限强度,且随点蚀损伤强度增大壁厚损伤度的影响加剧;点蚀体积损伤强度由于综合考虑了壁厚损伤度和点蚀损伤强度的耦合因素,相比于独立考虑后两者,其更能合理地描述点蚀损伤对平台腿柱极限强度的影响,故点蚀体积损伤强度体现了点蚀损伤的关键特征。本方法不仅适用于研究点蚀损伤构件的极限承载力,其所提出的点蚀损伤模型的构建方法,可拓展于研究受点蚀损伤的整体平台结构的极限承载力,且确定点蚀体积损伤强度为描述点蚀损伤特征的关键参数后,有望将其用于修正点蚀损伤平台腿柱的承载力设计公式。     

深海管道钢的腐蚀疲劳裂纹扩展特性试验研究

采用侧壁开槽型CT试样,分别在空气和3.5%NaCl溶液中进行腐蚀疲劳裂纹扩展试验,研究海底管道用钢X65在海水腐蚀环境下的腐蚀疲劳裂纹扩展特性。为保证试样既能满足腐蚀疲劳试验机的夹具要求,又可控制裂纹沿直线方向扩展,采用侧壁开槽技术对CT试样进行改进;利用有限元软件ABAQUS,建立三维模型,验证了对于侧壁开槽型CT试样,可以采用ASTM标准推荐的应力强度因子表达式对改进后CT试样开展数值计算。利用YYF-50腐蚀疲劳试验装置开展试验,试验结果表明:和惰性环境相比,腐蚀环境不仅会加速X65钢的裂纹扩展速率,还会降低腐蚀疲劳体系下裂纹扩展的门槛值;在腐蚀体系下存在裂纹扩展的稳定阶段,可采用Paris公式对其腐蚀疲劳裂纹扩展速率进行预测。