水泥砾质土三轴试验研究

对某水泥砾质土进行了三轴固结排水剪切试验,研究在不同水泥掺入比下水泥砾质土应力-应变关系和强度特性。结果表明：随水泥掺入比的增加,水泥砾质土试样在不同围压下应力-应变关系曲线均表现出不同程度的软化和剪胀现象,尤其在低围压（200 kPa）和高水泥掺入比（8%）下,剪胀性比较明显;在相同水泥掺入比下,峰值强度 随围压的增加近似呈线性增长;与不掺水泥砾质土相比,水泥砾质土的内摩擦角 因掺入不同量的水泥而得到不同程度的提高,黏聚力 随水泥掺入比的增加呈增长趋势,且增幅显著;割线模量 和 均随围压和水泥掺入比的增加而增加。不同高度的心墙堆石坝三维有限元算例的计算结果表明：水泥砾质土作为心墙材料可以显著降低土石坝心墙沉降。     

Undrained behaviour of polypropylene fibre reinforced sandy soil under monotonic loading

Soil improvement using fibres is widely used in soil stabilisation to prevent sand liquefaction. In order to study the undrained behaviour and liquefaction resistance of sand reinforced with polypropylene fibres, a series of triaxial compressive tests were conducted on unreinforced and reinforced Chlef sand with different contents of polypropylene fibres (0, 0.3, 0.5 and 0.8%). Samples were prepared at 30% and 80% relative densities representing loose and dense states respectively, and triaxial tests were performed at confining pressures of 50, 100 and 200 kPa. Tests results show that fibre inclusion has a significant effect on the shear strength and dilation of sandy soil. The increase in strength is function of fibre content, relative density and confining pressure. The maximum strength improvement for both loose and dense fibre-reinforced sand is more pronounced at higher confining pressure and at higher fibre content.     

The behaviour of an artificially cemented sandy gravel

The major section of the city of Tehran, Iran has been developed on cemented coarse-grained alluvium. This deposit consists of gravely sand to sandy gravel with some cobbles and is dominantly cemented by carbonaceous materials. In order to understand the mechanical behaviour of this soil, a series of undrained triaxial compression tests and unconfined compression tests were performed on uncemented and artificially cemented samples. Portland cement type I was used as the cementation agent for preparing artificially cemented samples. Uncemented samples and lightly cemented samples (1.5% cement) tested at high confining pressure showed contractive behaviour accompanied with positive excess pore water pressure and a barrelling failure mode. However, cemented samples and uncemented samples tested at low confining pressure (25 and 50 kN/m²) showed dilative behaviour accompanied with negative excess pore water pressure. Shear zones were formed in these samples and a clear peak in excess pore water pressure and stress ratio against strain could be observed. Test results showed that the limiting stress ratio surface for cemented samples is curved and expands as the cementation and density increase. Unconfined compression strength of cemented samples increases with increases in cementation and density as well.     

Triaxial behaviour of a cemented gravely sand, Tehran alluvium

Cemented coarse-grained alluvium is present in a vast area of Tehran city, Iran including its suburbs. This deposit consists of gravely sand to sandy gravel with some cobbles and is dominantly cemented by carbonaceous materials. In order to understand the mechanical behaviour of this soil, a series of triaxial compression tests were performed on uncemented, artificially cemented and destructured samples. Hydrated lime was used as the cementation agent for sample preparation to model the Tehran deposit. The tests were performed on cemented samples after an appropriate time for curing. The tests on cemented samples show that a shear zone appears as the shear stress approaches the peak shear strength. During shearing these samples undergo dilation at confining stress lower than 1000kPa. However, the uncemented and destructured samples show contraction during shearing. Peak shear strength is followed by strain softening for all cemented samples. The shear strength increases with increasing cement content but the influence of the cementation decreases as the confining stress increases. With increasing cementation the stress-strain behaviour of samples tend towards the behaviour expected of high-density soils. Test results indicate that the failure envelope for cemented samples is curved and not linear.     

水泥土芯样强度变形特性及本构关系试验研究

为了研究现场施工工艺下水泥土的强度及变形特性,对水泥搅拌桩钻孔芯样进行了无侧限抗压强度试验与三轴试验,分析了水泥掺量与围压对水泥土芯样强度、变形特性的影响规律。结果表明：随着水泥掺量的提高,水泥土芯样的强度明显增强,变形模量显著增大,但其破坏应变变小,脆性增大;水泥掺量超过18%的水泥土芯样其应力-应变关系表现为软化型,随着围压的提高,其强度增强,破坏应变增大,脆性降低,且应力-应变关系曲线有可能发生转型;不同围压下的水泥土芯样三轴试验先为体缩,后变化为体胀,发生剪胀的应变较破坏应变略小,是由剪切面上颗粒错动引起的,在颗粒错动达到一定程度后抗剪强度才发挥到峰值;水泥土的结构屈服应力比较大,在围压的作用下其胶结结构未发生破损,强度包线满足摩尔-库仑线性强度规律;根据水泥土的强度变形特征,应力-应变全曲线分弹性、塑性、软化3个阶段,可采用Popovics模型对其进行模拟,与试验结果较为吻合。     

循环荷载作用下纤维水泥土动力特性

通过动三轴试验,研究水泥土中掺入不同掺量的聚丙烯纤维和玄武岩纤维条件下,其动应力 、动弹性模量 随动应变的变化规律。试验结果表明：水泥土的动强度和动弹性模量与围压、掺入纤维的种类和纤维掺量有关;随着纤维掺量的增多,水泥土的动强度和动弹性模量增大,动变形减小。从滞回曲线和微观的角度分析,掺入玄武岩纤维的水泥土动力性能最好,聚丙烯纤维水泥土次之,素水泥土（无纤维）较弱;最大动弹性模量 随着围压和纤维掺量的增大而增大。玄武岩纤维水泥土在不同围压下的 归一化曲线相互聚拢,表明 对围压的依赖程度降低。     

砂土与EPS颗粒混合的轻质土的动剪切模量衰减特性分析

动荷载下砂土与EPS颗粒混合的轻质土（LSES）的割线剪切模量Gsec随着剪应变的累积会发生衰减，基于不同水泥掺量和EPS含量的LSES试样的动三轴试验结果，建立了与围压、剪应变、水泥掺量等因素相关的Gsec的经验衰减模型。通过比较发现，LSES与砂及胶结砂的Gsec衰减模型具有一定相似性，即Gsec与yd呈双曲线关系，与σc为指数关系。此外，由于水泥胶结的约束作用，Gsec对σc的依存度随水泥掺量的增加而减小，这种依存程度通过参数n反映出来，但当水泥掺量达到10％时n随其的变化就不明显了，这是因为胶结强度已经增大到使得LSES中颗粒间的相对位置不易发生错动的程度。     

Laboratory Investigation into the Effects of Silty Fines on Liquefaction Susceptibility of Chlef (Algeria) Sandy Soils

In a number of recent case studies, the liquefaction of silty sands has been reported. To investigate the undrained shear and deformation behaviour of Chlef sand–silt mixtures, a series of monotonic and stress-controlled cyclic triaxial tests were conducted on sand encountered at the site. The aim of this laboratory investigation is to study the influence of silt contents, expressed by means of the equivalent void ratio on undrained residual shear strength of loose, medium dense and dense sand–silt mixtures under monotonic loading and liquefaction potential under cyclic loading. After an earthquake event, the prediction of the post-liquefaction strength is becoming a challenging task in order to ensure the stability of different types of earth structures. Thus, the choice of the appropriate undrained residual shear strength of silty sandy soils that are prone to liquefaction to be used in engineering practice design should be established. To achieve this, a series of undrained triaxial tests were conducted on reconstituted saturated silty sand samples with different fines contents ranging from 0 to 40 %. In all tests, the confining pressure was held constant at 100 kPa. From the experimental results obtained, it is clear that the global void ratio cannot be used as a state parameter and may not characterize the actual behaviour of the soil as well. The equivalent void ratio expressing the fine particles participation in soil strength is then introduced. A linear relationship between the undrained shear residual shear strength and the equivalent void ratio has been obtained for the studied range of the fines contents. Cyclic test results confirm that the increase in the equivalent void ratio and the fines content accelerates the liquefaction phenomenon for the studied stress ratio and the liquefaction resistance decreases with the increase in either the equivalent void ratio or the loading amplitude level. These cyclic tests results confirm the obtained monotonic tests results.     

连云港软黏土的不排水强度试验研究

对连云港软黏土不扰动样和重塑样进行三轴CU对比试验研究。结果表明,不扰动样的不排水强度包线是由以屈服压力为界的双折线组成,而重塑样的不排水强度包线可以用通过圆点的直线表示。屈服前阶段,不扰动样由于受结构性影响产生的抵抗作用,其不排水强度包线高于重塑样;屈服后阶段,不扰动样的不排水强度包线介于具有不同初始含水率的重塑样的包线之间。通过对比分析,发现不扰动样与重塑样的不排水强度包线存在差异的主要原因是由于试样的不同初始含水率引起的。不扰动样在屈服后阶段的含水率变化规律与不排水强度增长规律与重塑土相一致,采用Burland提出的孔隙指数Iv,可将不同初始含水率重塑样及屈服后阶段不扰动样的压缩性状较好地归一化。     

原状膨胀土剪切力学特性的应变速率效应

为研究应变速率对原状膨胀土力学性状的影响,通过GDS三轴试验系统进行了不同速率和围压下的固结不排水三轴剪切试验,分析了应力−应变曲线、孔隙水压力、剪切强度以及破坏模式随应变速率的变化规律。结果表明：不同应变速率下,膨胀土应力−应变曲线均呈应变硬化型。随着应变速率的增加,不排水剪切强度单调递增,引入应变速率参数ρ_0.9后发现,不排水强度增长率为14.3%～23.2%,平均值为18.4%。低围压下,应变速率对孔隙水压力影响较小,随着围压的增大,孔隙水压力的发展趋势由软化型转变为硬化型,孔隙水压力峰值随应变速率的增大而减小。原状膨胀土应变速率效应与其多裂隙性密切相关,破坏形式表现为小应变速率下主剪切带与次剪切带共存,大应变速率下仅有主剪切带,裂隙或多剪切带的出现强化了膨胀土强度的应变速率效应。     

生活垃圾焚烧炉渣在饱和状态下的强度特性

城市生活垃圾焚烧炉渣具有活性,饱和炉渣的剪切强度随时间增加而增加。本文采用常规三轴试验测试饱和炉渣的剪切强度,围压σ₃分别为50kPa、100kPa、200kPa和400kPa,试样的干密度ρ_d分别为1.4g·cm-3、1.5g·cm-3和1.6g·cm-3,龄期t分别为3d、7d、14d和28d。三轴试验结果表明:饱和炉渣的破坏模式受龄期和围压的影响明显。围压小于200kPa,龄期小于14d的试样表现为脆性破坏。在τ-σ坐标上,应力莫尔圆的包络线不是直线;炉渣在σ₁-σ₃坐标上表现为两段直线,分界点为σ₃=200kPa,由σ₁-σ₃相关关系确定炉渣的内摩擦角和黏聚力更合理可信。     

Undrained Triaxial Behavior of Cement Treated Marine Clay

Clays treated with lower cement contents often exhibit behaviour similar to stiff clays with planar failure surface under triaxial compression. In the present work the behaviour of a marine clay treated with 5 % cement, subjected to undrained triaxial compression tests is studied. The pre-consolidation pressure of the cemented clay due to the cementation bonding is observed to be very high. It is attempted to model the behaviour of cement treated clay using a bounding surface plasticity formulation as the plastic behaviour of the cemented clays within the yield surface has to be considered. The effect of cementation is included in the model as the pre-consolidation pressure obtained from consolidation tests. The tensile strength due to cementation bonds is included in the equation of the bounding surface. Simulations of the undrained triaxial compression tests on cemented clays are carried out and the results are validated with the experimental results.     

Evaluation of shear strength of cohesionless soil due to excess pore water pressure

The shear strength of cohesionless soil is reduced as the water pressure inside the pores of the soil mass increases. The mathematical relationship between the shear strength and the pore water pressure was derived using Mohr–Coulomb failure criteria as a function of the confining pressure and the effective angle of friction. Experimentally, a series of consolidated drained triaxial tests with back pore water pressure was run on samples of saturated uniform dense sand. The tests were conducted at different confining pressures in the range of 100–400 kPa with an increment of 100 kPa. At each level of confining pressure, the tests were repeated at different values of back pore water pressure in the range of 0–100 kPa with an increment of 25 kPa. For each test, the initial applied back pore water pressure was kept constant during the test for comparing the results at the same effective confining pressure. This study concludes that the mathematical relationship gives accurate results at any level of confining pressure and/or pore water pressure as a function of the effective angle of friction that can be evaluated using single consolidated drained triaxial test at zero back pore water pressure.     

钱塘江冲海积粉土剪胀性三轴试验研究

钱塘江两岸广泛分布着冲海积粉土.通过大量的三轴固结不排水CU和固结排水CD试验,探讨饱和粉土的应力应变性状和剪胀特性。试验表明,钱塘江冲海积粉土显著的特性之一是在剪切中膨胀,剪胀主要与粉土的密度和围压有关。CU试验中密(e=0.739～0.866)的原状样在围压600kPa范围内剪切膨胀,稍密(e=0.890～0.906)的击实样在围压低于400kPa剪切膨胀。由于粉土膨胀的本质不排水强度在剪切中保持增加,对于这种情况就没有惟一的"不排水强度";CD试验稍密(e=0.889～0.945)的击实样在围压低于400kPa时剪切膨胀。钱塘江冲海积粉土的剪切破坏要经历一个大的变形过程,固结排水剪切过程的应力应变性状可分为4个阶段。取应变继续而没有进一步体积变化的临界状态做破坏标准,确定粉土排水剪切强度指标较合理。     

Effect of Strain Rate on the Strength Characteristics of Soil–Lime Mixture

The effects of rate of strain on strength and deformation characteristics of soil–lime were investigated. Five strain rates (0.1, 0.8, 2.0, 4.0 and 7.0 %/min), five lime contents (0, 3, 6, 9 and 12 %) by dry soil weight and three cell pressures (100, 200 and 340 kN/m²) were carried. Triaxial tests, under unconsolidated condition, were used to study the effect of strain rate on strength and initial modulus of elasticity of soil and soil–lime mixture after two curing periods 7 and 21 days, respectively. A total of 405 triaxial specimens have been tested, where 225 specimens have been tested with first curing period (7 days). The testing program includes nine specimens for each strain rate, and each lime content was carried out, including natural soil with zero lime content. Another set of triaxial tests with a total of 180 specimens for the second curing period (21 days) was prepared at optimum moisture content, and the corresponding maximum dry density was also tested. The effects of strain rate and curing period on each of stress–strain behavior, type of failure, deviator stress at failure, cohesion and angle of internal friction and initial modulus of elasticity were studied thoroughly for the natural soil as well as soil–lime mixtures. For natural soil, the test results showed that the undrained shear strength, the initial modulus of elasticity and the cohesion increase significantly as the strain rate increase, while for soil–lime mixture at different curing periods, the undrained shear strength, initial modulus of elasticity and the cohesion increases to a maximum and then decreases as the strain rate and lime content increase. Also, the same variables and angle of internal friction increase with increasing curing period.     

废轮胎颗粒与黄土混合物剪切特性研究

废轮胎应用于岩土工程不仅开辟了废轮胎处置的新途径,还为解决岩土工程问题提供了新型复合材料。为了更好地模拟实际回填土受力工况,采用不固结不排水三轴试验研究了掺量为10%～50%的废轮胎颗粒与黄土混合物（以下简称GR-LM,granulated rubber loess mixtures）的剪切特性,考察了掺量、围压对剪切强度的影响。对试验结果进行了机制探讨。研究表明,所有GR-LM试样均表现出应变硬化特点,纯废轮胎颗粒在试验所有围压范围内呈近似线性的偏应力-应变特性;GR-LM应力-应变特性与掺量和围压有关,低围压下存在剪切强度增大的掺量为30%,其GR-LM强度高于其他各掺量混合土并略高于纯压实黄土的剪切强度;GR-LM剪切强度机制与GR-LM孔隙填充状态、基质土物理状态、弹性骨架颗粒有关,总体上随骨架颗粒的不同接触关系而表现出粉土与粒状土的强度特性,在剪切强度特性上体现出掺量与围压作用的相互耦合,而与压实粉土或砂土有所不同。     

水泥稳定再生沥青路面/红土混合物用于软土改良的效果评估

评估了水泥稳定再生沥青路面（RAP）/边缘红土混合物作为碎石桩骨料替代传统采石场骨料的潜力,研究了混合材料在不同RAP置换率和有效约束压力下的不排水剪切强度变化。RAP置换率分别为10%、30%和50%（按干重计）,普通硅酸盐水泥含量分别为1%和3%。很明显,RAP的置换增加了大颗粒,同时减少了细小颗粒,因此增加了压实度。在低于先期固结压力的有效应力下,RAP−土颗粒混合物表现出与孔隙压力降低相关的应变硬化性能。当RAP置换率增加时,水泥稳定的RAP−土颗粒混合物应力−应变曲线的应变软化性能减弱。胶结作用提高了黏聚力,而内摩擦角未产生明显的变化。水泥稳定的RAP−土颗粒混合物的强度和刚度主要取决于胶结强度和RAP置换率。抗剪强度随着非稳定和水泥稳定的RAP−土颗粒混合物的RAP置换率增加而提高,而水泥稳定的RAP−土颗粒混合物的刚度由于沥青黏结剂的高能量吸收而下降。     

陇西黄土三轴剪切过程微观变化研究

为了解黄土三轴剪切过程中的微观变化,采用PFC3D建立黄土三轴试验模型,模拟围压分别为0、50、150、300 kPa的三轴剪切试验,并与室内试验进行对比分析。分析结果表明：PFC3D能够较好地模拟出不同围压下从开始到破坏到残余变形整个过程中应力-应变的变化规律,且位移场及接触应力场的变化规律与室内三轴试验宏观现象较一致;发现弹性模量、泊松比及峰值强度与数值模型中微观参数有着密切的联系,如法向刚度kn控制试样宏观弹性模量,kn /ks值控制泊松比,摩擦系数控制峰值强度;通过体应变-轴向应变曲线发现,随着围压的增加应变能增大,试样呈现出由体积膨胀到体积减缩的变化规律。其研究结果为进一步探究黄土的应力-应变性状及抗剪强度特性提供参考。     

三轴冲击荷载作用下淤泥力学响应研究

利用SPAX-2000（改进型）静动真三轴系统,针对淤泥类超软土进行静动力排水固结试验,研究包括较高频率在内的各冲击荷载频率（1、8、16 Hz）与不同围压（200、250、300 kPa）作用下淤泥的力学响应;此外,结合三轴剪切试验研究不同固结条件对淤泥不排水强度的影响。试验结果表明：（1）在相同冲击频率作用下,试样抗剪强度随着围压增大而提高;围压增大,使得球应力增大,体应变随着增大,有效地促进试样排水固结。（2）相同围压作用下,存在着一个冲击荷载频率阈值,当冲击频率低于这一阈值时,随着冲击荷载频率的提高,轴向应变量逐渐变小,反之逐渐变大。（3）冲击瞬间,体应变为负值,表现为体胀,这与原位试验夯击瞬间的孔隙水压力变化曲线一致,从而验证了高含水率淤泥在冲击作用下的孔压负增长现象。     

Evaluation of a constitutive model for clays and sands: Part I – sand behaviour

This paper evaluates the performance of a generalized effective stress soil model for predicting the rate independent behaviour of freshly deposited sands, while a companion paper describes model capabilities for clays and silts. Most material parameters can be obtained from standard laboratory data, including hydrostatic or one‐dimensional compression, drained and undrained triaxial shear testing. A compilation of data on compression behaviour allows for estimation of compression parameters when this type of data is not available. Extensive comparisons of model predictions with measured data from undrained triaxial shear tests shows that the model gives excellent predictions of the transition from dilative to contractive shear response as the confining pressure and/or the initial formation void ratio increases. A parametric study of drained response shows that the model describes realistically the variation of peak friction angle and dilation rate as a function of confining pressure and density when compared with an empirical correlation valid for many sands. The proposed formulation predicts a unique critical state locus for both drained and undrained triaxial testing which is non‐linear over the entire range of stresses and is in excellent agreement with recent experimental data. Overall, the model provides excellent predictions of the stress–strain–strength relationships over a wide range of confining pressures and formation densities. Copyright © 2002 John Wiley & Sons, Ltd.