Predicting onset of cyclic instability of loose sand with fines using instability curves

This study utilises the equivalent granular state parameter, ψ^⁎, as a key parameter for studying static and cyclic instability and their linkage. ψ^⁎ can be considered as a generalisation of the state parameter as first proposed by Been and Jefferies so that the influence of fines content in addition to stress and density state can be captured. Test results presented in this study conclusively showed that ψ^⁎ at the start of undrained shearing and η_IS, the stress ratio at onset of static instability, can be described by a single relationship irrespective of fines content for both compression and extension shearing. This single relationship is referred as instability curve. However, the instability curve in extension shearing is different from that of compression. In this paper, the capacity of the instability curve in predicting triggering of cyclic instability was evaluated experimentally. An extensive series of undrained one-way (compression) and non-symmetric two-way cyclic triaxial tests, in addition to monotonic triaxial tests in both compression and extension were conducted for this evaluation. Furthermore, a published database for Hokksund sand with fines was also used. Test results show that cyclic instability was triggered shortly after the cyclic effective stress path crossed the estimated η_IS-zone(s) as obtained from instability curve(s) irrespective of whether instability occurs in the compression or extension side.     

Interfacial instability of sand patterns induced by turbulent shear flow

When a turbulent shear flow above a plane sand surface entrains sand grains,it generates a variety of sand patterns.Fluvial sand forms two major interfacial patterns:meso-scale dunes and antidunes,and large-scale bars.Measurements have evidenced that under erosive conditions,meso-scale patterns either change to or coexist with large-scale patterns.However,it remains elusive what exactly drives the switching of interfacial patterns and how the switching occurs.Here,we showdcombing a flow model with a grain transport model,allowing for both the surface and suspended sand fluxes dthat the switching of patterns emerges from the shear-driven complex feedback between grain transport and topographic perturbations.The switching predominantly depends on the magnitudes of the Rouse number and the grain size to undisturbed flow depth ratio.The model offers quantitative predictions of the maximum amplification of sand patterns and unveils a new attraction erepulsion phenomenon.     

The effect of plastic fines on the pore pressure generation characteristics of saturated sands

Pore water pressure generation during earthquake shaking initiates liquefaction and affects the shear strength, shear stiffness, deformation, and settlement characteristics of soil deposits. The effect of plastic fines (kaolinite) on pore pressure generation in saturated sands was studied through strain-controlled cyclic triaxial tests. In addition to pore pressure generation, this experimental study also focused on evaluating the threshold shear strain for pore pressure generation and the volumetric compressibility of specimens during pore pressure dissipation. The results reveal that specimens having up to 20% plastic fines content generated larger values of pore water pressure than clean sand specimens. At 30% fines content, the excess pore water pressure decreased below that of clean sand. The threshold shear strain, which indicates the strain level above which pore pressures begin to generate, was assessed for different kaolinite–sand mixtures. The threshold shear strain was similar for 0–20% fines (γ_t0.006–0.008%), but increased to about 0.025% for 30% fines. The volumetric compressibility, measured after pore pressure generation, was similar for all specimens. The transition of behavior at fines contents between 20% and 30% can be attributed to a change in the soil structure from one dominated by sand grains to one dominated by fines.     

Influence of fines content on liquefied strength of silty sands

Critical state soil mechanics is a useful framework to understand sand behavior. In this paper, a relationship is developed for estimating undrained critical shear strength of sands based on the critical state framework. The relationship is validated by comparison with laboratory test results and sand liquefied strength from field liquefaction failure case histories. Using this relationship, the influence of fines content on undrained critical shear strength is studied for different combinations of effective stress and density. The parametric study indicates that depending on soil void ratio, effective stress, and the shape and mineralogy of the fine particles, undrained critical strength may increase, remain the same, or decrease as the amount of fines content increases. Both the susceptibility to liquefaction and the severity of strain-softening are affected by adding fines. It is suggested that the critical state parameter is inadequate for describing the behavior of liquefiable sands and sand shearing-compressibility should be taken into account in liquefaction analysis.     

Effect of depositional method on the undrained behavior and microstructure of sand with silt

It has been known for many years that depositional method plays an important part in the results of laboratory testing of clean sands. In this paper, undrained triaxial compression tests were performed on specimens composed of Nevada sand with 20% non-plastic silt content using a variety of depositional methods that include slurry deposition, water sedimentation, air pluviation, mixed dry deposition, and dry funnel deposition. It was found that there was a marked difference in the undrained behavior even though the density and stress conditions were identical. The conclusion was that the soil fabric was responsible for this result. Using the scanning electron microscope, a method was developed to examine and quantify the microstructure of silty sand. These results appear to indicate that there are internal particle structures in sand with silt and their relative quantities correlate with the observed macroscopic undrained behavior.     

Performance of laterally loaded H-piles in sand

Results from experimental testing of four approximately one-third scale laterally loaded H-piles, subjected to monotonic and cyclic loading are presented. The test setups were designed to prevent torsion in the pile during testing and to eliminate the self-weight of the hydraulic actuator that could otherwise induce moment on the model piles. The tests were conducted in compacted medium dense sand and all the piles were extensively instrumented. Test results indicate that the lateral force–displacement responses under cyclic loading exhibited slight pinching behavior due to the gap that opened at the top of the soil-pile interface. Numerical simulations show that p–y curves based on the American Petroleum Institute (API) recommendations and that proposed by Reese et al. can reasonably predict the lateral response of the piles though slightly underestimate the ultimate capacities. The general pile behavior such as force–displacement response and moment distributions along the pile depth show slight sensitivity to the subgrade reaction modulus at large displacements.     

Effects of chemical dispersants and mineral fines on crude oil dispersion in a wave tank under breaking waves

The interaction of chemical dispersants and suspended sediments with crude oil influences the fate and transport of oil spills in coastal waters. A wave tank study was conducted to investigate the effects of chemical dispersants and mineral fines on the dispersion of oil and the formation of oil-mineral-aggregates (OMAs) in natural seawater. Results of ultraviolet spectrofluorometry and gas chromatography flame ionized detection analysis indicated that dispersants and mineral fines, alone and in combination, enhanced the dispersion of oil into the water column. Measurements taken with a laser in situ scattering and transmissometer (LISST-100X) showed that the presence of mineral fines increased the total concentration of the suspended particles from 4 to 10microl l(-1), whereas the presence of dispersants decreased the particle size (mass mean diameter) of OMAs from 50 to 10microm. Observation with an epifluorescence microscope indicated that the presence of dispersants, mineral fines, or both in combination significantly increased the number of particles dispersed into the water.     

Effects of gravel and sand mulches on dew deposition in the semiarid region of China

Information regarding dew deposition on the stone-covered surface is scarce. The effects of gravel and sand mulches on dew condensation were studied during the late summer and fall of 1999 in the semiarid loess region of China. The results indicated that there were significant difference in daily dew amount between gravel mulch, sand mulch and dry loess soil (control). The average dew amount for gravel mulch was 0.071 mm d⁻¹ with extreme 0.022 and 0.20 mm d⁻¹. The average values for sand mulch and dry loess soil was 0.12 and 0.15 mm d⁻¹, respectively. The minimum dew amount was 0.048 mm d⁻¹ for sand mulch and 0.071 mm d⁻¹ for dry loess soil, and the maximum dew amount was approximate 0.25 mm d⁻¹ for both treatments. The results suggest that surface stone mulch can reduce dew deposition as compared to sand and dry loess soil.     

Local analysis of the magnetic instability in rotating magnetohydrodynamics with the short-wavelength approximation

We investigate analytically the magnetic instability in a rotating and electrically conducting fluid induced by an imposed magnetic field with its associated electric current. The short-wavelength approximation is used in the linear stability analysis, i.e. the length scale of the imposed field is much larger than the wavelength of perturbations. The dispersion relationship is derived and then simplified to give the criteria for the onset of the magnetic instability in three cases of imposed field, namely, the axial dependence, the radial dependence and the mixed case. The orientation of rotation, imposed field and imposed current is important for this instability.     

Cyclic undrained behavior of silty sand

Laboratory cyclic triaxial tests were performed to investigate the effect of fine content on the pore pressure generation in sand. Strain-controlled, consolidated undrained tests have been performed with a cyclic shear strain range of 0·015-1·5%. These tests were carried to 1000 cycles or to initial liquefaction, which ever occurred first. Triaxial tests were performed on pure sand silt specimens and specimens with silt additions of 10, 20, 30, and 60% by weight. Two types of silt, a non-plastic silt and a low plasticity silt (PI 10) were used as control materials. The main parameters varied in this study were the amount of silt, the plasticity index of silt, and the void ratio where the observed parameter was the pore pressure generation. For all silt contents, silt plasticity and the number of loading cycles have no significant effect at strain levels below 0·01%. Therefore, threshold strain for silty sands have approximately the same value as sands. For both non-plastic and low plasticity silts, there is a significant increase in the generated pore pressure at high strain levels.     

Improved bounds on linear instability of barotropic zonal flow within the shallow water equations

Here we develop mathematical results to describe the location of linear instability of a parallel mean flow within the framework of the shallow water equations; growth estimates of near neutral modes (for disturbances subcritical with respect to gravity wave speed) in the cases of non-rotating and rotating shallow water. The bottom topography is taken to be one-dimensional and the isobaths are parallel to the mean flow. In the case of a rotating fluid, the isobaths and the mean flow are assumed to be zonal. The flow is front-like: there is a monotonic increase of mean flow velocity. Our results show that for barotropic flows the location of instabilities will be a semi-ellipse region in the complex wave velocity plane, that is based on the wave-number, Froude number, and depth of the fluid layer. We also explore the instability region for the case of spatially unbounded mean velocity profiles for non-rotating shallow water.     

Effects of mechanical and chemical processes on the degradation of plastic beach debris on the island of Kauai, Hawaii

Plastic debris is accumulating on the beaches of Kauai at an alarming rate, averaging 484 pieces/day in one locality. Particles sampled were analyzed to determine the effects of mechanical and chemical processes on the breakdown of polymers in a subtropical setting. Scanning electron microscopy (SEM) indicates that plastic surfaces contain fractures, horizontal notches, flakes, pits, grooves, and vermiculate textures. The mechanically produced textures provide ideal loci for chemical weathering to occur which further weakens the polymer surface leading to embrittlement. Fourier transform infrared spectroscopy (FTIR) results show that some particles have highly oxidized surfaces as indicated by intense peaks in the lower wavenumber region of the spectra. Our textural analyses suggest that polyethylene has the potential to degrade more readily than polypropylene. Further evaluation of plastic degradation in the natural environment may lead to a shift away from the production and use of plastic materials with longer residence times.     

On the modelling of sand bedforms using the semivariogram

This study shows the usefulness of the semivariogram for modelling sand ripples created by water flows of varied flow intensity. A combination of two mathematical functions is fitted to each sample semivariogram, that is an exponential (or stochastic) component and a periodic component. The parameters of each of these components have direct physical meaning. A non-dimensional ratio combining the two parameters of the exponential model is interpreted as a regularity index (which increases with the degree of regularity of bedform arrangement). This regularity index is inversely related to the Froude number of the flow. The non-dimensional wavelength, estimated from the dominant periodic function, is also inversely and closely related to the Froude number. The wave height, accurately estimated from properties of the two fitted components, is a direct function of flow velocity and is also proportional to the standard deviation of bed elevations. The bedform shape introduces a considerable discrepancy between the generally assumed normal frequency distribution and the empirical distributions of bed height. The series of bed elevations are generally characterized by a mixture of normal distributions having the same variance but different means. The calculation of a covariance assuming a constant and single mean (as in spectral analysis) can therefore be misleading and the problem may be avoided by using the semivariogram.     

Grain size dependency in the occurrence of sand waves

Sandy shallow seas, like the North Sea, are very dynamic. Several morphological features are present on the bed, from small ripples to sand waves and large tidal sandbanks. The larger patterns induce significant depth variations that have an impact on human activities taking place in this area. Therefore, it is important to know where these large-scale features occur, what their natural behaviour is and how they interact with human activities. Here, we extend earlier research that compares the results of an idealized model of large-scale seabed patterns with data of seabed patterns in the North Sea. The idealized model is extended with a grain size dependency. The adaptations lead to more accurate predictions of the occurrence of large-scale bed forms in the North Sea. Therefore, grain size dependency and, in particular, critical shear stress are important to explain the occurrence of sand waves and sandbanks in the North Sea. Responsible Editor: Alejandro Souza     

Evolution of sand waves in the Messina Strait, Italy

In the present paper the morphodynamics of sand waves in the Messina Strait, Italy, is analysed by comparing data gathered during two different surveys carried out in 1991 and 2001, respectively. In particular, a morphometric analysis on the most recent data and a qualitative analysis of the differences between bottom bedform patterns, are carried out. At locations characterised by greater depths, only minor changes to the planimetric configuration of the field, i.e. crest orientation (which is seen to be orthogonal to the direction of net gross sand transport) and wave length are observed, while differences in wave length and crest direction are more evident in more shallow areas. On the other hand, wave height has significantly increased in the whole field. A possible explanation of such a change, based on the previsions of a theory which relates sand-wave growth and migration to the main components of the tidal ellipse, is provided.Responsible Editor: Jens Kappenberg     

泡沫塑料颗粒种类对轻质混合土力学特性的影响

轻质混合土是一种新型的轻质土工材料,具有轻质、环保、高强等特点。本文对添加不同种类泡沫塑料颗粒的轻质混合土试样进行了无侧限抗压强度试验、等向压缩试验及三轴剪切试验。试验结果表明:泡沫塑料颗粒种类对轻质混合试样的力学特性有较大的影响。     

Mitigating the effects of sand dunes on seismic data from the Rub al Khali basin,Saudi Arabia

The Rub Al Khali region in Saudi Arabia is characterized by the presence of sand dunes separated by salt flats, also called Sabkhas. In general, the elevation of dunes in this region varies between 90 and 250 m above sea level. The presence of these sand dunes, along with the rapidly changing surface topography poses challenges for seismic data acquisition and processing. The high contrast in acoustic impedance between the dune base and the underlying formation often results in amplification of seismic waves that are recorded at stations located on the surface of sand dunes. Attempts to address the issue using conventional surface-consistent amplitude scaling methods without reducing these amplification effects generally fail, thus compromising the suitability of the processed data for amplitude versus offset analysis. In this study, we propose a new reference site technique to reduce the effects of sand dune amplification, enabling the production of data sets that are suitable for amplitude versus offset processing. The proposed technique uses a deterministic approach to derive surface-consistent, frequency-dependent de-amplification functions for shots and stations located on the dunes only. Two-dimensional synthetic and field data examples show that the technique significantly reduces the effects of sand dune amplification.     

Shear modulus and damping ratio of grouted sand

An experimental comparative study of three different grouted sands in terms of their effects on the values of two dynamic properties is presented. The dynamic properties studied are the shear modulus and the damping ratio which are determined with resonant column tests and cyclic triaxial tests. The behaviour of a pure Fontainebleau sand is compared with the behaviour of a Fontainebleau sand grouted with a silicate grout, a micro-fine cement grout and a mineral grout. The effects of the grouting treatment, the type of grout, the confining pressure, and the strains, on the shear modulus and the damping ratio are studied. The test results have shown that grouting improves the stiffness of the sand especially for small strains. Whatever the type of material, confining stress improves the shear modulus whereas it has a negligible effect on the damping ratio. When strain increases, the shear modulus decreases and the damping ratio increases.     

The pollution of the marine environment by plastic debris: a review

The deleterious effects of plastic debris on the marine environment were reviewed by bringing together most of the literature published so far on the topic. A large number of marine species is known to be harmed and/or killed by plastic debris, which could jeopardize their survival, especially since many are already endangered by other forms of anthropogenic activities. Marine animals are mostly affected through entanglement in and ingestion of plastic litter. Other less known threats include the use of plastic debris by "invader" species and the absorption of polychlorinated biphenyls from ingested plastics. Less conspicuous forms, such as plastic pellets and "scrubbers" are also hazardous. To address the problem of plastic debris in the oceans is a difficult task, and a variety of approaches are urgently required. Some of the ways to mitigate the problem are discussed.     

两河口水电站混合料流变模型研究

对两河口水电站混合料进行了三轴流变试验研究,对其流变机理和模型进行了探讨。两河口水电站混合料的轴向和体积流变特性可以用幂函数来描述,模型参数可根据试验得到的流变特性确定,并对流变模型参数的影响因素及取值进行了分析。