基于物理模型试验的多层滑带堆积层滑坡—抗滑桩受力特征

研究抗滑桩的受力特征是进行抗滑桩设计工作的关键。我国三峡库区部分堆积层滑坡发育多层滑带,而目前抗滑桩的设计方法仅针对单层滑坡,因此,对多层滑带堆积层滑坡—抗滑桩受力特征的研究具有重要意义。基于三峡库区堆积层滑坡工程地质特征,开展了多层滑带堆积层滑坡物理试验模型,在滑坡的后缘施加推力来模拟滑坡演化过程,同时监测滑坡—抗滑桩体系的多场信息。试验结果表明,在多层滑带堆积层滑坡的演化过程中,桩身受力表现出了很好的规律性。根据坡表位移的变化趋势,将滑坡演化分为4个阶段,在此基础上对桩身受力进行分析。滑坡推力分布图式中出现了4个极大值,土体抗力分布图式中出现唯一最大值,该试验结果为抗滑桩的设计提供了一定的理论支持。      

基于物理模型试验的滑坡-抗滑桩位移场变化特征

滑坡-抗滑桩体系演化机理是滑坡灾害防治的重要理论基础,其中桩土相互作用是滑坡-抗滑桩体系中的关键,而位移场是相互作用的重要表征之一,因此,对滑坡-抗滑桩体系位移场的研究具有十分重要的工程意义。以物理模型试验为手段,基于三峡库区堆积层滑坡工程地质特征,建立大型物理试验模型,通过逐级施加荷载来模拟滑坡后缘推力,采用高速摄像机及粒子图像测速技术等获取滑坡坡表与桩顶位移数据,定量分析了体系位移场变化特征。试验结果显示:在滑坡-抗滑桩体系演化过程中,坡表位移场变化呈现出很好的规律性,这为桩土相互作用研究机理起到了一定的推动作用。      

三峡库区麻柳林滑坡变形特征及演化模拟

在库水位波动和降雨作用的共同影响下，库岸滑坡的变形规律往往更为复杂。以三峡库区麻柳林滑坡为例，基于野外调查、钻探编录、深部位移监测以及数值模拟等手段，分析了库水位波动和降雨作用下滑坡变形特征及演化规律。结果表明:麻柳林滑坡在粉质黏土层和块石层交界处发育一个次级滑带，目前该滑坡主要沿次级滑带运动，导致次级滑动的原因与坡体物质的差异性有关；S_i(S_f)指标分析法揭示滑坡的滑带还未完全破坏，滑坡仍处于蠕变状态；根据三峡水库水位调度规律，将一个完整水文年划分为6个阶段，数值模拟结果表明滑坡在库水位缓慢下降阶段变形速率较小、在快速下降阶段和低水位阶段变形速率持续增大、在快速上升阶段和缓慢上升阶段以及高水位阶段变形速率则保持平稳。其中，降雨的直接影响和降雨导致库水位波动进而对滑坡变形造成的间接影响，使得麻柳林滑坡在低水位阶段的变形显著增加、稳定性最差，应加强该时段内滑坡的监测和预警。      

基于物理模型试验的杆塔基础滑坡防护措施效果研究

大量穿越山地丘陵区的高压输电线路杆塔基础常位于滑坡灾害高易发斜坡地段,施加适当防护措施提高其稳定性,是保障输电线路持续安全运行的关键。为研究不同防护措施对杆塔基础滑坡的防护效果,以湖北省巴东县燕子滑坡为地质原型,设计制作物理试验模型,分别开展了极端降雨条件下滑坡在无防护、施加抗滑桩与格构护坡时的物理模型试验,从试验角度揭示了滑坡变形破坏特征与不同防护措施的防护效果。试验结果表明：在2种极端降雨工况(50,100 mm/h)下,无防护的滑坡体历经了坡表冲刷、裂缝扩展、局部垮塌变形与整体滑动的演化过程;抗滑桩措施对滑坡整体的防护效果显著,滑坡整体处于稳定状态,杆塔基础变形较小,杆塔倾斜率满足规范,但坡表会出现冲刷垮塌现象;格构护坡措施能有效减少坡面冲刷和坡脚垮塌风险,但在持续强降雨条件下对杆塔基础的整体稳固作用稍弱。物理模型试验结果与滑坡历史变形和实际治理效果吻合,试验结论可为类似杆塔基础滑坡的破坏机理研究与防护工程设计提供借鉴。     

基于极限位移准则和变形预测的滑坡变形潜势分析

为准确掌握库区滑坡变形潜势,在变形监测成果统计基础上,首先利用极限位移准则开展滑坡现状变形潜势分析;然后以相关向量机为理论基础,通过优化处理保证其参数最优性,构建滑坡变形预测模型,并以预测结果开展滑坡变形潜势的发展趋势评价;最后结合两种分析结果,实现滑坡综合变形潜势分析。结果表明,不同监测点的现状变形潜势状态存在一定差异,由不利原则可知,现状变形潜势等级为Ⅳ级,潜势程度属严重状态;滑坡变形仍会进一步增加,变形潜势趋于不利方向发展。综合两种分析结果可知,滑坡变形潜势处于不利状态,后期失稳可能性较大,应加强灾害防治,避免成灾损失。     

基于模型试验的动水驱动型顺层岩质滑坡启滑机制初探

动水驱动型顺层岩质滑坡数量多、灾害频发、危害大, 是滑坡地质灾害领域的研究重点, 但目前对于滑坡启滑机制的认识仍不充分, 滑坡的准确预报还面临巨大挑战。鉴于此, 以含软弱夹层的中倾角顺层岩质滑坡为研究对象, 通过构建理想的单层滑带滑坡物理模型, 开展了一系列动水作用下的滑坡模型试验研究。结果表明, 动水作用下顺层岩质滑坡从开始变形至失稳滑动需经历初始变形、缓慢变形、加速变形和失稳破坏4个阶段, 而各个阶段的演化特征与滑面粗糙度和倾角密切相关。滑面倾角越大或粗糙度越小, 滑坡体从开始变形至失稳滑动所需的时间则越短; 相应地, 坡体加速变形阶段越不明显, 滑坡破坏的突发性越强。滑带内的渗流冲蚀作用会使滑带土中的骨料流失, 导致其抗剪强度降低, 进而引发坡体滑动。与此同时, 上覆坡体的压剪作用以及变形演化过程亦将反过来影响冲蚀强度。基于滑带土黏聚力随水力梯度和冲蚀时间的变化关系, 提出了渗流驱动下滑带土黏聚力演化模型, 可较好地描述滑带土黏聚力的退化过程。滑面粗糙度的存在不仅显著影响了滑带的冲蚀劣化规律, 还改变了滑带不同区域的破坏模式。此外, 通过考虑滑面粗糙度对滑带不同区域破坏模式的影响, 开展了动水多效应关联分析, 建立了滑坡地质体力学分析模型, 实现了动水作用下顺层岩质滑坡动态稳定性的有效评估。本研究成果可为实际动水驱动型顺层岩质滑坡的预测和防治提供理论参考。      

鲁西尚河韧性剪切带变形特征研究

发育于鲁西隆起区尼山凸起内的尚河韧性剪切带,其韧性变形在不同阶段主导变形机制不同:初期的变形机制以晶格错位和显微破裂为主;中期以韧性流动、物质扩散迁移为主;晚期以晶质塑性变形和颗粒边界滑动为主。在剪切带的发育过程中,岩石的物质成分和体积都发生了较大变化。根据构造岩的矿物组合和形变特征判断,该剪切带具右行走滑性质,其剪切位移量为1048m。尚河韧性剪切带变质变形温度较低,属绿片岩相动力变质作用。     

基于多源数据的谭家湾滑坡变形机制及稳定性评价

针对2016年5月发生于秭归县西北部的谭家湾滑坡,结合卫星遥感影像、现场勘查资料以及历史资料等多源数据,初步明确了滑坡的影响区域、特征及发生时序;综合采用钻探、槽探、物探等手段,开展室内外相关实验,明确了滑坡区的地层特性以及岩土体物理力学性质指标,通过分析该区裂缝位移及GPS数据,对该边坡的变形机制进行了探讨,并对该区稳定性进行了评价。结果表明:①谭家湾滑坡属于不规则"圈椅形"中型松散层的水库下降型滑坡,滑坡区的地表形态、地质构造及岩性等因素决定了滑坡的形成和发育,库水位和降雨的共同作用激励了滑坡的变形;②滑坡根据时序共分为3级滑体,总体呈现多次、多层、相互影响的演化特点,第三级滑体具有牵引式特征;③滑坡体内地下水位随库水位下降而下降,但下降速率缓于库水位,随之坡体内水力梯度和渗透力显著变大,此时碰到强降雨,将会导致坡体地下水赋存,岩土体软化,加剧滑坡变形,须施加必要的防护措施。④稳定性分析表明,该滑坡现处于临界稳定状态,一旦发生降雨和库水位变化,局部段可能发生失稳滑动。      

基于灰色理论的滑坡变形反演与预测研究

以紫阳县城滑坡为例,采用灰色理论的单序列一阶线性动态模型,在探讨滑坡变形规律的基础上,着重研究了滑坡变形的趋势预测及主要特征点变形的位移反演,为全面研究滑坡各阶段的变形规律提出了一种分析方法     

基于神经网络的滑坡变形预测报研究

利用ＢＰ神经网络方法建立了滑坡变形预报模型,在此模型的基础上对几个典型滑坡进行了预报分析,其结果表明用ＢＰ模型进行滑坡短期预报效果较好。     

Displacement characteristic of landslides reinforced with flexible piles: field and physical model test

A field monitoring system was established in an active river bank landslide in the Three Gorges area, China, and a consecutive monitoring for about 5 years were conducted to understand the displacement characteristics of flexible piles and the surrounding soil. It was found that piles deformed elastically under reservoir operation, and the soil in front of piles was gradually separated from piles. The movement of the pile heads exceeded that of the soil between and behind piles. This phenomenon was further studied by a large-scale physical model test to gain insights into the pile-soil interaction. The displacement relationship between pile heads and the surrounding soil is in good agreement with the field data. The physical model test shows that the deformation process of pile-reinforced landslides can be divided into two stages: firstly, when the piles head movement exceeds soil movement, the soil arching is mainly affected by the deflection of the piles, the arches between and behind piles bent upwards;but when the soil movement exceeds piles head movement, the arches near the upslope and downslope bent downwards and upwards, respectively. Furthermore, the different deformation of two adjacent piles and the pile stiffness influenced the arch’s shape and formation;the flexible piles exhibit great coordinated deformation with the landslide, and caused the soil arch on the downslope.     

Shaking table test for reinforcement of soil slope with multiple sliding surfaces by reinforced double-row anti-slide piles

Despite the continuous advancements of engineering construction in high-intensity areas, many engineering landslides are still manufactured with huge thrust force, and double-row piles are effective to control such large landslides. In this study, large shaking table test were performed to test and obtain multi-attribute seismic data such as feature image, acceleration, and dynamic soil pressure. Through the feature image processing analysis, the deformation characteristics for the slope reinfor...     

Three-dimensional stability of landslides based on local safety factor

Unlike the limit equilibrium method (LEM), with which only the global safety factor of the landslide can be calculated, a local safety factor (LSF) method is proposed to evaluate the stability of different sections of a landslide in this paper. Based on three-dimensional (3D) numerical simulation results, the local safety factor is defined as the ratio of the shear strength of the soil at an element on the slip zone to the shear stress parallel to the sliding direction at that element. The global safety factor of the landslide is defined as the weighted average of all local safety factors based on the area of the slip surface. Some example analyses show that the results computed by the LSF method agree well with those calculated by the General Limit Equilibrium (GLE) method in two-dimensional (2D) models and the distribution of the LSF in the 3D slip zone is consistent with that indicated by the observed deformation pattern of an actual landslide in China.     

湖北省阳新县基岩滑坡变形因子及其破坏模式

斜坡变形受众多因子综合控制,不同因子的敏感性与作用规律在变形过程中差异明显。以湖北省阳新县顺层基岩滑坡为研究对象,通过正交试验结合离散元数值模拟的方法,研究多个影响因子对应顺层滑坡变形的敏感性并确立主导因素,随后基于响应面拟合主导因素与滑坡不同部位变形程度间的量化关系,揭示主导因素交互作用对滑坡变形破坏模式的影响规律。结果表明,在研究区内坡度与岩层倾角分别为影响顺层滑坡变形的主导与次主导因素,滑坡的变形破坏模式受控于二者的交互作用。在中-陡倾顺层滑坡中,当坡度小于岩层倾角时,滑坡变形主要集中在坡顶,且变形程度随岩层倾角的增加而增大,表现出滑移-弯曲的变形破坏模式;在缓倾顺层滑坡中,当坡度大于岩层倾角时,滑坡坡脚位移较坡顶显著,其坡脚变形程度随坡度的增加而增大,以滑移-拉裂变形为主。研究成果可为该类滑坡的防治工作提供参考。     

Failure behavior of soil-rock mixture slopes based on centrifuge model test

The stability of soil-rock mixtures(SRMs) that widely distributed in slopes is of significant concern for slope safety evaluation and disaster prevention. The failure behavior of SRM slopes under surface loading conditions was investigated through a series of centrifuge model tests considering various volumetric gravel contents. The displacement field of the slope was determined with image-based displacement system to observe the deformation of the soil and the movement of the block during loading in the tests. The test results showed that the ultimate bearing capacity and the stiffness of SRM slopes increased evidently when the volumetric block content exceeded a threshold value. Moreover, there were more evident slips around the blocks in the SRM slope. The microscopic analysis of the block motion showed that the rotation of the blocks could aggravate the deformation localization to facilitate the development of the slip surface. The high correlation between the rotation of the key blocks and the slope failure indicated that the blocks became the dominant load-bearing medium that influenced the slope failure. The blocks in the sliding body formed a chain to bear the load and change the displacement distribution of the adjacent matrix sand through the block rotation.     

Microstructure evolution of loess under multiple collapsibility based on nuclear magnetic resonance and scanning electron microscopy

In recent years, the acceleration of urbanization in loess areas has prompted frequent dismantling and reconstruction of old urban areas. Demolition and reconstruction of buildings involve multiple collapses of the foundation. To study microstructure evolution of loess under multiple collapsibility, this paper selects undisturbed loess samples from Guyuan, Northwest China for multiple compression tests. Using nuclear magnetic resonance(NMR) imaging and scanning electron microscopy(SEM) as auxiliary methods, a combination of qualitative and quantitative analyses was used to study the microstructure of loess samples before and after various number of collapses under different pressures. Results show that the loess does undergo multiple collapse under 200 kPa pressure. Pore is an important reason for loess collapse. The initial collapse comes primarily from the compression of macropores and mesopores, and the second collapse comes primarily from mesopore compression. The compression process of loess can be roughly divided into two stages. First, under the action of dissolution and compression, the relative displacement of soil particles occurs. Macropores and mesopores are destroyed first, generating small pores. Second, with increasing pressure and times of collapses, pore compression gradually transforms into small pore compression. During the first collapse, particle aggregates disintegrate due to water and pressure. However, with increasing times of collapses, the contact relationship between particles gradually changes from the point contact to face contact. Loess particles tend to gradually become rounded. The study of the microstructure provides the possibility to further reveal the mechanism of multiple collapsibility of loess.