Numerical study of sediment transport above rippled beds under the action of combined waves and currents

To study sediment suspension above ripples under the combined action of waves and currents, a three‐dimensional numerical model has been developed based on the use of FLUENT software, and an external sediment transport model. The computer model has been tested against laboratory measurements involving oscillatory wave motion, as well as cases of co‐linear waves with following and opposing currents, with satisfactory results. Compared with the situation in which only waves are present (called waves‐alone cases), the effects from the steady current on both vortex shedding and sediment suspension above ripples have clearly been revealed by the model results. In particular, the vortices generated in combined waves and currents tend to stay low in the trough area of the ripple and are ejected earlier than those in the waves‐alone case at both the ripple crest and trough, which leads to concentration peaks at different phases and with different magnitudes. The model was also applied to a field case from a multi‐barred, dissipative beach at Egmond‐an‐Zee, in the Netherlands, to investigate the influences of a long‐shore current on cross‐shore sediment transport. The model results show reasonable overall agreement with the field measurements, as well as the important effects of the three dimensional flow structure on the sediment entrainment process close to the ripple surface, which is very difficult to observe in such detail in field studies.     

Sediment suspension under waves and currents: time scales and vertical structure

Field measurements of the vertical structure of near-bed suspended sediment concentrations were obtained from arrays of fast response optical backscatter suspended solids sensors to examine the time-dependent response of sediment resuspension to waves and currents and the constraints imposed by bedforms. Data were recorded from both a nonbarred, marine shoreface and a barred lacustrine shoreface, under both shoaling and breaking waves (significant heights of 0·25–1·50m; peak periods of 3 and 8 s) and in water depths of 0·5–5·0 m. Sediment concentrations are positively correlated with increasing elevation above the bed, but lagged in time. The time lag varies directly with separation distance between measurement locations and inversely with the horizontal component of the near-bed oscillatory velocity. Both the presence of wave groups and the settling velocities of the sediment particules in suspension influence the temporal changes in concentration at a given elevation. Sediment concentrations appear to respond more slowly to the incident wind-wave forcing with distance away from the bed as a result of two factors: (1) the sequential increase in concentration induced by a succession of large waves in a group; and (ii) the relative increase in finer sediments with smaller settling velocities. Bedforms interact with the near-bed horizontal currents to impose a distinct constraint upon the timing of suspension events relative to the phase of the fluid motion, and, therefore, the vertical structure of the suspended sediment concentration at a range of time scales. The near-bed concentrations appear to be strongly dependent upon the vertical convection of sediment associated with the ejection from the wave boundary layer of separation vortices generated in the lee of ripple crests. Concentration gradients in the presence of vortex ripples are large, as are the correlation between concentrations measured at different elevations within the fluid.     

Geometry and grain-size sorting of ripples on low-energy sandy beaches: field observations and model predictions

ABSTRACT There are very few field measurements of nearshore bedforms and grain‐size distribution on low‐energy microtidal beaches that experience low‐amplitude, long‐period waves. Field observations are needed to determine grain‐size distribution over nearshore bedforms, which may be important for understanding the mechanisms responsible for ripple development and migration. Additional nearshore field observations of ripple geometry are needed to test predictive models of ripple geometry. Ripple height, length and sediment composition were measured in the nearshore of several low‐energy beaches with concurrent measurements of incident waves. The distribution of sediment sizes over individual ripples was investigated, and the performance of several models of ripple geometry prediction was tested both spatially and temporally. Sediment samples were collected from the crest and trough of 164 ripples. The sand‐sized sediment was separated from the small amount (generally <3%) of coarser material (>2 mm) that was present. Within the sand‐sized fraction, the ripple crests were found to be significantly coarser, better sorted and more positively skewed than the troughs. Overall, the troughs were finer than the crests but contained a greater proportion of the small fraction of sediment larger than 2 mm. The field model of Nielsen (1981 ) and the model of Wiberg & Harris (1994 ) were found to be the most accurate models for predicting the wavelength of parallel ripples in the nearshore of the low‐energy microtidal environments surveyed. The Wiberg & Harris (1994 ) model was also the most accurate model for predicting ripple height. Temporal changes in ripple wavelength appear to be dependent on the morphological history of the bed.     

Bedform spurs: a result of a trailing helical vortex wake

The formative conditions for bedform spurs and their roles in bedform dynamics and associated sediment transport are described herein. Bedform spurs are formed by helical vortices that trail from the lee surface of oblique segments of bedform crest lines. Trailing helical vortices quickly route sediment away from the lee surface of their parent bedform, scouring troughs and placing this bed material into the body of the spur. The geometric configuration of bedform spurs to their parent bedform crests is predicted by a cross‐stream Strouhal number. When present, spur‐bearing bedforms and their associated trailing helical wakes exert tremendous control on bedform morphology by routing enhanced sediment transport between adjacent bedforms. Field measurements collected at the North Loup River, Nebraska, and flume experiments described in previous studies demonstrate that this trailing helical vortex‐mediated sediment transport is a mechanism for bedform deformation, interactions and transitions between two‐dimensional and three‐dimensional bedforms.     

On the relationship between flow and suspended sediment transport over the crest of a sand dune, Río Paraná, Argentina

The links between large‐scale turbulence and the suspension of sediment over alluvial bedforms have generated considerable interest in the last few decades, with past studies illustrating the origin of such turbulence and its influence on flow resistance, sediment transport and bedform morphology. In this study of turbulence and sediment suspension over large sand dunes in the Río Paraná, Argentina, time series of three‐dimensional velocity, and at‐a‐point suspended sediment concentration and particle‐size, were measured with an acoustic Doppler current profiler and laser in situ scattering transmissometer, respectively. These time series were decomposed using wavelet analysis to investigate the scales of covariation of flow velocity and suspended sediment. The analysis reveals an inverse relationship between streamwise and vertical velocities over the dune crest, where streamwise flow deceleration is linked to the vertical flux of fluid towards the water surface in the form of large turbulent fluid ejections. Regions of high suspended sediment concentration are found to correlate well with such events. The frequencies of these turbulent events have been assessed from wavelet analysis and found to concentrate in two zones that closely match predictions from empirical equations. Such a finding suggests that a combination and interaction of vortex shedding and wake flapping/changing length of the lee‐side separation zone are the principal contributors to the turbulent flow field associated with such large alluvial sand dunes. Wavelet analysis provides insight upon the temporal and spatial evolution of these coherent flow structures, including information on the topology of dune‐related turbulent flow structures. At the flow stage investigated, the turbulent flow events, and their associated high suspended sediment concentrations, are seen to grow with height above the bed until a threshold height (ca 0·45 flow depth) is reached, above which they begin to decay and dissipate.     

浅水非线性波作用下沙纹床面底层流动特性试验研究

通过水槽试验研究浅水非线性波作用下沙纹床面底层流动特性,利用CCD图像技术观测分析非对称沙纹的形成和演化规律。利用声学多普勒测速仪(ADV)测量非对称沙纹底床上的流场,得到了不同波高、周期、水深条件下的沙纹峰顶和谷底断面的瞬时速度。试验结果分析表明,浅水非线性波作用下床面上形成非对称沙纹,其近底流速具有较强紊动特性,随着距床面距离的增大紊动强度逐渐减弱。在水流方向改变时,沙纹背部具有明显漩涡运动。沙纹背后形成的漩涡能起到维持沙纹的作用。浅水非线性波作用下,沙纹的形成原因主要是床面泥沙颗粒在非对称流动和床面近壁粘性底层中漩涡结构动力作用下,作受迫摆动、推移所致。     

Fine-scale relief related to Late Holocene channel shifting within the floor of the upper Redondo Fan, offshore Southern California

Erosional and depositional bedforms have been imaged at outcrop scale in the upper Redondo Fan, in the San Pedro Basin of offshore Southern California in ≥600 m water depths, using an Autonomous Underwater Vehicle developed by the Monterey Bay Aquarium Research Institute. The Autonomous Underwater Vehicle is equipped with multibeam and chirp sub-bottom sonars. Sampling and photographic images using the Monterey Bay Aquarium Research Institute Remotely Operated Vehicle Tiburon provide groundtruth for the Autonomous Underwater Vehicle survey. The 0·3 m vertical and 1·5 m lateral bathymetric resolution and 0·1 m sub-bottom profile resolution provide unprecedented detail of bedform morphology and structure. Multiple channels within the Redondo Fan have been active at different times during the Late Holocene (0 to 3000 yr bp ). The currently active channel extending from Redondo Canyon makes an abrupt 90° turn at the canyon mouth before resuming a south-easterly course along the east side of the Redondo Fan. This channel is floored by sand and characterized by small steps generally <1 m in relief, spaced 10 to 80 m in the down-channel direction. A broader channel complex lies along the western side of the fan valley that was last active more than 850 years ago. Two distinct trains of large scours, with widths ranging from tens to a few hundred metres and depths of 20 m, occur on the floor of the western channel complex, which has a thin mud drape. If observed in cross-section only, these large scours would probably be misidentified as the thalweg of an active channel.     

Subaqueous density flow processes and deposits of an island volcano landslide (Stromboli Island, Italy)

Stromboli is a 3000 m high island volcano, rising to 900 m above sea-level. It is the most active volcano of the Aeolian Archipelago in the Tyrrhenian Sea (Italy). Major, large volume (1 km³) sector collapses, four occurring in the last 13 kyr, have played an important role in shaping the north-western flank (Sciara del Fuoco) of the volcano, potentially generating a high-risk tsunami hazard for the Aeolian Islands and the Italian coast. However, smaller volume, partial collapses of the Sciara del Fuoco have been shown to be more frequent tsunami-generating events. One such event occurred on 30 December 2002, when a partial collapse of the north-western flank of the island took place. The resulting landslide generated 10 m high tsunami waves that impacted the island. Multibeam bathymetry, side-scan sonar imaging and visual observations reveal that the landslide deposited 25 to 30 × 10⁶ m³ of sediment on the submerged slope offshore from the Sciara del Fuoco. Two contiguous main deposit facies are recognized: (i) a chaotic, coarse-grained (metre-sized to centimetre-sized clasts) deposit; and (ii) a sand deposit containing a lower, cross-bedded sand layer and an upper structureless pebbly sand bed capped by sea floor ripple bedforms. The sand facies develops adjacent to and partially overlying the coarse deposits. Characteristics of the deposits suggest that they were derived from cohesionless, sandy matrix density flows. Flow rheology and dynamics led to the segregation of the density flow into sand-rich and clast-rich regions. A range of density flow transitions, both in space and in time, caused principally by particle concentration and grain-size partitioning within cohesionless parent flows was identified in the deposits of this relatively small-scale submarine landslide event.     

Pyroclastic dune bedforms: macroscale structures and lateral variations. Examples from the 2006 pyroclastic currents at Tungurahua (Ecuador)

Pyroclastic currents are catastrophic flows of gas and particles triggered by explosive volcanic eruptions. For much of their dynamics, they behave as particulate density currents and share similarities with turbidity currents. Pyroclastic currents occasionally deposit dune bedforms with peculiar lamination patterns, from what is thought to represent the dilute low concentration and fluid‐turbulence supported end member of the pyroclastic currents. This article presents a high resolution dataset of sediment plates (lacquer peels) with several closely spaced lateral profiles representing sections through single pyroclastic bedforms from the August 2006 eruption of Tungurahua (Ecuador). Most of the sedimentary features contain backset bedding and preferential stoss‐face deposition. From the ripple scale (a few centimetres) to the largest dune bedform scale (several metres in length), similar patterns of erosive‐based backset beds are evidenced. Recurrent trains of sub‐vertical truncations on the stoss side of structures reshape and steepen the bedforms. In contrast, sporadic coarse‐grained lenses and lensoidal layers flatten bedforms by filling troughs. The coarsest (clasts up to 10 cm), least sorted and massive structures still exhibit lineation patterns that follow the general backset bedding trend. The stratal architecture exhibits strong lateral variations within tens of centimetres, with very local truncations both in flow‐perpendicular and flow‐parallel directions. This study infers that the sedimentary patterns of bedforms result from four formation mechanisms: (i) differential draping; (ii) slope‐influenced saltation; (iii) truncative bursts; and (iv) granular‐based events. Whereas most of the literature makes a straightforward link between backset bedding and Froude‐supercritical flows, this interpretation is reconsidered here. Indeed, features that would be diagnostic of subcritical dunes, antidunes and ‘chute and pools’ can be found on the same horizon and in a single bedform, only laterally separated by short distances (tens of centimetres). These data stress the influence of the pulsating and highly turbulent nature of the currents and the possible role of coherent flow structures such as Görtler vortices. Backset bedding is interpreted here as a consequence of a very high sedimentation environment of weak and waning currents that interact with the pre‐existing morphology. Quantification of near‐bed flow velocities is made via comparison with wind tunnel experiments. It is estimated that shear velocities of ca 0·30 m.s^?1 (equivalent to pure wind velocity of 6 to 8 m.s^?1 at 10 cm above the bed) could emplace the constructive bedsets, whereas the truncative phases would result from bursts with impacting wind velocities of at least 30 to 40 m.s^?1.     

A field study of turbulence and sediment dynamics over subaqueous dunes with flow separation

This study examines flow, turbulence and sand suspension over large dunes in Canoe Pass, a distributary channel of the Fraser River delta, Canada. Dune morphology is characterized by a symmetrical shape and steep leeside slopes over 30°. Velocity was measured with an electromagnetic current meter and suspended sand concentration with four optical backscatter (OBS) probes. The general patterns of time-averaged velocity and sand suspension are consistent with previous studies, including an increase in mean velocity and decrease in turbulence intensity and sand concentration with height above the bed, reversed flow with high turbulence intensity and high sand concentrations in the leeside flow separation zone and an increase in near-bed velocity and sand concentration along the stoss side of the dune. Frequency spectra of near-bed velocity and OBS records from leeside separation zones are composed of two distinct frequencies, providing field confirmation of scale relations based on flume experiments. The low-frequency spectral signal probably results from wake flapping and the high-frequency signal from vortex shedding. The wake-flapping frequency predominates outside the separation zone and is linked to turbulent structures that suspend sand. Predictions from a depth-scale Strouhal Law show good agreement with measured wake-flapping frequencies. Cross-correlations of OBS records reveal that turbulent sand suspension structures advect downstream at 23–25° above the horizontal. These advection angles are similar to coherent flow structures measured in flumes and to sand suspension structures visualized over large dunes in the field.     

Sedimentary processes in the Selvage sediment-wave field, NE Atlantic: new insights into the formation of sediment waves by turbidity currents

An integrated geophysical and sedimentological investigation of the Selvage sediment-wave field has revealed that the sediment waves are formed beneath unconfined turbidity currents. The sediment waves occur on the lower continental rise and display wavelengths of up to 1 km and wave heights of up to 6 m. Wave sediments consist of interbedded turbidites and pelagic/hemipelagic marls and oozes. Nannofossil-based dating of the sediments indicates a bulk sedimentation rate of 2·4 cm 1000 years^–1, and the waves are migrating upslope at a rate of 0·28 m 1000 years^–1. Sediment provenance studies reveal that the turbidity currents maintaining the waves are largely sourced from volcanic islands to the south. Investigation of existing models for sediment-wave formation leads to the conclusion that the Selvage sediment waves form as giant antidunes. Simple numerical modelling reveals that turbidity currents crossing the wave field have internal Froude numbers of 0·5–1·9, which is very close to the antidune existence limits. Depositional flow velocities range from <6 to 125 cm^–1. There is a rapid increase in wavelength and flow thickness in the upper 10 km of the wave field, which is unexpected, as the slope angle remains relatively constant. This anomaly is possibly linked to a topographic obstacle just upslope of the sediment waves. Flows passing over the obstacle may undergo a hydraulic jump at its boundary, leading to an increase in flow thickness. In the lower 15 km of the wave field, flow thickness decreases downslope by 60%, which is comparable with results obtained for other unconfined turbidity currents undergoing flow expansion.     

Three‐dimensional seismic analysis of sediment waves and related geomorphological features on a carbonate shelf exposed to large amplitude internal waves,Browse Basin region,Australia

This study analyses the three‐dimensional geometry of sedimentary features recorded on the modern sea floor and in the shallow subsurface of a shelf to upper slope region offshore Australia that is characterized by a pronounced internal wave regime. The data interpreted comprise an extensive, >12 500 km² industrial three‐dimensional seismic‐reflection survey that images the northern part of the Browse Basin, Australian North West Shelf. The most prominent seismic–morphological features on the modern sea floor are submarine terrace escarpments, fault‐scarps and incised channels, as well as restricted areas of seismic distortion interpreted as mass wasting deposits. Besides these kilometre‐scale sea floor irregularities, smaller bedforms were discovered also, including a multitude of sediment waves with a lateral extent of several kilometres and heights up to 10 m. These sedimentological features generally occur in extensive fields in water depths below 250 m mostly at the foot of submerged terraces, along the scarps of modern faults and along the shelf break between the outer shelf and the upper continental rise. Additional bedforms that characterize the more planar regions of the outer shelf are elongate, north‐west/south‐east oriented furrows and ridges. The formation of both sediment waves and furrow‐ridge systems requires flow velocities between 0·3 m sec^?1 and 1·5 m sec^?1, which could be generated by oceanic currents, gravity currents or internal waves. In the studied setting, these velocities can be best explained as being generated by bottom currents induced by internal waves, an interpretation that is discussed against oceanographic background data and modelling results. In addition to the documentation of three‐dimensional seismic–geomorphological features of the modern sea floor, it was also possible to map kilometre‐scale buried sediment wave fields in the seismic volume down to ca 500 ms two‐way‐time below the present sea floor, indicating the general potential for the preservation of such bedforms in the sedimentary record.     

Sediment transport and bedforms in a carbonate tidal inlet; Lee Stocking Island, Exumas, Bahamas

An active oolitic sand wave was monitored for a period of 37 days in order to address the relationship between the direction and strength of tidal currents and the resultant geometry, and amount and direction of migration of bedforms in carbonate sands. The study area is situated in a tidal channel near Lee Stocking Island (Exumas, Bahamas) containing an estimated 5.5 to 6 × 10⁵ m³ of mobile oolitic sand. Tidal ranges within the inlet are microtidal and the maximum current velocity at the studied site is 0.6 m s^?1. At least 300–400 m³ of mostly oolitic sand are formed within, or brought into, the channel area every year. The tidal inlet is subdivided into an ocean-orientated segment, in which sand waves are shaped by both flood and ebb tides, and a platform-orientated segment, where sand waves are mainly shaped by flood tides. The studied sand wave lies on the platformward flood-tide dominated segment in a water depth of 3.5.4.5 m. During the 37 days of observation, the oolitic and bioclastic sand wave migrated 4 m in the direction of the dominant flood current. The increments of migration were directly related to the strength of the tide. During each tidal cycle, bedforms formed depending on the strength of the tidal current, tidal range and their location on the sand wave. During flood tides, a steep lee and a gentle stoss side formed and current ripples and small dunes developed on the crest of the sand wave, while the trough developed only ripples. The average lee slope of the sand wave is 24.2°, and therefore steeper than typical siliciclastic sand waves. During ebb tides, portions of the crest are eroded creating a convex upward ebb stoss side, covered with climbing cuspate and linguoid ripples and composite dunes. The area between the ebb-lee side and the trough is covered with fan systems, sinuous ripples and dunes. The migration of all bedforms deviated to a variable degree from the main current direction, reflecting complex flow patterns in the tidal inlet. Small bedforms displayed the largest deviation, migrating at an angle of up to 90° and more to the dominant current direction during spring tides.     

Physical criteria for distinguishing sandy tsunami and storm deposits using modern examples

Modern subaerial sand beds deposited by major tsunamis and hurricanes were compared at trench, transect, and sub-regional spatial scales to evaluate which attributes are most useful for distinguishing the two types of deposits. Physical criteria that may be diagnostic include: sediment composition, textures and grading, types and organization of stratification, thickness, geometry, and landscape conformity.

Published reports of Pacific Ocean tsunami impacts and our field observations suggest that sandy tsunami deposits are generally < 25 cm thick, extend hundreds of meters inland from the beach, and fill microtopography but generally conform to the antecedent landscape. They commonly are a single homogeneous bed that is normally graded overall, or that consists of only a few thin layers. Mud intraclasts and mud laminae within the deposit are strong evidence of tsunami deposition. Twig orientation or other indicators of return flow during bed aggradation are also diagnostic of tsunami deposits. Sandy storm deposits tend to be > 30 cm thick, generally extend < 300 m from the beach, and will not advance beyond the antecedent macrotopography they are able to fill. They typically are composed of numerous subhorizontal planar laminae organized into multiple laminasets that are normally or inversely graded, they do not contain internal mud laminae and rarely contain mud intraclasts. Application of these distinguishing characteristics depends on their preservation potential and any deposit modifications that accompany burial.

The distinctions between tsunami and storm deposits are related to differences in the hydrodynamics and sediment-sorting processes during transport. Tsunami deposition results from a few high-velocity, long-period waves that entrain sediment from the shoreface, beach, and landward erosion zone. Tsunamis can have flow depths greater than 10 m, transport sediment primarily in suspension, and distribute the load over a broad region where sediment falls out of suspension when flow decelerates. In contrast, storm inundation generally is gradual and prolonged, consisting of many waves that erode beaches and dunes with no significant overland return flow until after the main flooding. Storm flow depths are commonly < 3 m, sediment is transported primarily as bed load by traction, and the load is deposited within a zone relatively close to the beach.     

Time-sequence observations of wave-formed sand ripples on an ocean shoreface

Analysis of an 18-day time-lapse film record of shoreface ripple development, with concurrent measurements of near-bottom flow and surface waves, provides new insight on equilibrium bedform conditions, adjustment of ripple planform to variable hydrodynamics, and ripple migration behaviour. The study was conducted in approximately 10 m water depth, 1 km off Martinique Beach on the Atlantic coast of Nova Scotia (Canada), under low-energy summer wave conditions. Significant wave-height and peak period during the study averaged 0–7 m and 8 s, respectively, with extremes up to 1–7 m and 11 s during passage of three weak weather disturbances. Six mutually exclusive ripple types have been defined: (1) short-wavelength regular ripples; (2) variable bifurcated ripples; (3) variable terminated ripples; (4) short-crested ripples; (5) long-wavelength regular ripples; and (6) chaotic ripples. Ripple wavelength ranged from 0–07 m to 0–24 m and displayed a strong Reynolds number dependence. Together with other published field data, the results suggest a lower limit of γ=0–06 m for the wavelength of wave ripples in ocean shoreface environments. Ripple orientation ranged through 38° and responded rapidly to changes in wave approach direction, but did not conform to the orientation of the adjacent shoreline. Ripples were observed to migrate both on- and off-shore (with and against the wave advance direction) at rates up to ±0–1 m h^-1, associated with net flows other than wave-induced onshore asymmetry and mass transport. Migration (mainly of ripple types 1 and 2) occurred during the peak of storm events, but showed no obvious correlation with measured near-bottom flow magnitude or direction. Ripple behaviour demonstrates equilibrium with prevailing dynamic conditions when straight-crested rippie types 1 and 5 are present. Disequilibrium in orientation or dimensions is expressed by increasing sinuosity, bifurcation and crest termination in types 2,3,4 and 6.     

Flow and turbulence structure across the ripple–dune transition: an experiment under mobile bed conditions

Current knowledge of flow and turbulent processes acting across the sand bed continuum is still unable to unequivocally explain the mechanism(s) by which ripples become dunes. Understanding has been improved by comparative high-resolution studies undertaken over fixed bedforms at different stages in the continuum. However, these studies both ignore the role of mobile sediment and do not examine flow structure during the actual transition from ripples to dunes. The aims of the paper are: (i) to describe flow and turbulence characteristics acting above mobile bedforms at several stages across the transition; and (ii) to compare these data with those arising from experiments over fixed ripples and dunes. Laboratory experiments are presented that examine the turbulence structure across seven distinct stages of the transition from ripples to dunes. Single-point acoustic Doppler velocimeter sampling at three flow heights above a developing mobile boundary was undertaken. Time-averaged statistics and the instantaneous quadrant record reveal distinct changes in flow structure either side of the change from ripples to dunes. Initially, shear-related, high-frequency vortex shedding dominates turbulence production. This increases until two-dimensional (2D) dunes have formed. Thereafter, turbulence intensities and Reynolds stress decline and three-dimensional dunes exhibit values found over 2D ripples. This is the result of shear layer dampening which occurs when the topographically-accelerated downstream velocity increases at a faster rate than flow depth. Activity at reattachment increases due to high velocity fluid imparting high mass and momentum transfer at the bed and/or wake flapping. Suspended sediment may also play a role in turbulence dampening and bed erosion. Ejections dominate over sweeps in terms of event frequency but not magnitude. Strong relationships between inward interactions and sweeps, and ejections and outward interactions, suggest that mass and momentum exchanges are dependent upon activity in all four quadrants. The results contradict the notion present in most physical models that larger bedforms exhibit most shear layer activity. Consequently an improved model for the ripple–dune transition is proposed.     

Fluvial processes and facies sequences in the sandy braided South Saskatchewan River, Canada

The South Saskatchewan River has a long term average discharge of 275 m³/sec, with flood peaks in the range of 1500 to 3800 m³/sec. South of Saskatoon, the four major types of geomorphological elements recognised are channels, slipface-bounded bars, sand flats and vegetated islands and floodplains. Major channels are 3-5 m deep, up to 200 m wide, and flow around sand flats which are 50-2000 m long, and around vegetated islands up to 1 km long. At areas of flow expansion, long straight-crested cross-channel bars form. During falling stage, a small part of the crest of the cross-channel bar may become emergent, and act as a nucleus for downstream and lateral growth of a new sand flat. The dominant channel bedforms are dunes, which deposit trough cross bedding. Cross-channel bars deposit large sets of planar tabular cross bedding. Sand flats that grow from a nucleus on a cross-channel bar are mostly composed of smaller planar tabular sets, with some parallel lamination, trough cross-bedding, and ripple cross-lamination. A typical facies sequence related to sand flat growth would consist of in-channel trough cross-bedding, overlain by a large (1-2 m) planar tabular set (cross-channel bar), overlain in turn by a complex association mostly of small planar tabular cross-beds, trough cross-beds and ripple cross-lamination. By contrast, a second stratigraphic sequence can be proposed, related only to channel aggradation. It would consist dominantly of trough cross-beds, decreasing in scale upward, and possible interrupted by isolated sets of planar tabular cross-bedding if a cross-channel bar formed, but failed to grow into a sand flat. During final filling of the channel, ripple cross-lamination and thin clay layers may be deposited. In the S. Saskatchewan, these sequences are a minimum of 5 m thick, and are overlain by 0.5-1 m of silty and muddy vertical accretion deposits.     

Frequency spectra and intermittency of the turbulent suspension process in a sand-bed river

Previous research suggests that the turbulence-driven suspension process in sand-bed channels is dominated by intermittent, energetic eddies with length scales of the order of channel depth. Because of the scarcity of data on the turbulent suspension process in alluvial channels, the possible variability in suspension intermittency and turbulent frequency content due to contrasts in flow depth, velocity or bedforms remains unclear however. The present study analyses eddy correlation suspension signals from seven deployments in varied flow conditions around a sandy meander bend. Deployment depths at near-bankfull flow stages varied from 2 to 5.5 m, velocities at 0.75–1 m height from 0.6 to 0.9 m s^?1 and local mean suspended sand concentrations ranged from 30 to 150 mg L^?1 in the intermittence and spectral content of sand suspension between the various deployments are analysed and results are compared with previously published findings. Study data suggest that the dominant eddy sizes involved in sediment mixing across the sensor level are consistently of the order of 1–5 times flow depth and lie within the ‘energy-bearing’ turbulent range. When sand suspension is analysed in the time domain in the various deployments, energetic, burst-like suspension events occupying only 1-5% of the record duration account for 20-90% of the suspension work. The degree of intermittence in the suspension process was observed to increase in deeper flows, where mixing events contributing extreme vertical sediment fluxes appear to be relatively more frequent.