Effect of salt on strength development of marine soft clay stabilized with cement-based composites

Abstract

Marine soft clay with a high salt concentration is widely distributed in coastal areas. In this study, cement-based composites consisting of cement, silica fume, plant ash and NaOH were used as a substitute for ordinary Portland cement, and the effect of salt (sodium chloride) on the strength development of clay was investigated by unconfined compressive strength (UCS) testing and scanning electron microscopy (SEM). With the addition of sodium chloride (NaCl), the amount of cementitious materials decreased, and the salt (sodium chloride) was considered to consume the cement-based composites. The consumption effect could be quantitatively evaluated by the consumption index of salt (CIS) and the clay-water/cement ratio hypothesis. The relationship between the CIS and curing period and an UCS prediction model of clay stabilized with cement-based composites with different salt contents and curing times were established. The CIS gradually decreased with increasing curing time and cement-based composites content. The accuracy of the prediction model was evaluated by a comparative analysis between the measured strengths and predicted strengths; the deviation was mostly within 10%. SEM analyses were employed to describe the changes in the microstructure of the specimens and the influencing mechanism of salt on clay stabilized with cement-based composites.     

Primary yielding locus of cement-stabilized marine clay and its applications

ABSTRACT

Strength and stiffness properties of materials are widely studied and used in civil engineering practice. However, most studies are based on unconfined conditions, which are different from real status of soil. This study investigated the primary yielding and yield locus for cement-stabilized marine clay. In this study, two types of cement-stabilized soils were studied through isotropic compression, triaxial drained shearing, unconfined compression, and bender element testing. Specimens with 20–50% of cement content and 7–90 days of curing period were used for the tests. Stress–strain behavior and primary yielding were evaluated, followed by construction of the primary yield locus. The characteristics of the primary yield locus and its development with curing time then were studied. The results showed that the properties of the primary yield locus were dependent on the type of stabilized soil, but were independent of the cement content and curing period. Thus, the approach provides a way to estimate the primary yield stress and drained stress path before primary yielding for cement-stabilized soil under confined condition. An empirical function was used to fit the primary yield locus. The primary isotropic yield stress was correlated to unconfined compressive strength or maximum shear modulus. Three indirect methods were proposed to predict the primary yield stress for cement-stabilized marine clay. The results showed that the primary yield stress can be estimated with reasonable accuracy.     

Laboratory study on cement admixed marine silt bricks

For the purpose of efficient utilization of sediments dredged from harbor, a new method was proposed in this study. Marine silt bricks were made by mixing sediments with cement and gypsum, placing it in a cubic mold with 240 mm in length, 115 mm in width, and 53 mm in height, and curing for certain days. To investigate the effects of cement and initial water content of soil on the mechanical behavior of marine silt bricks, unconfined compressive and flexural strength tests were carried out. Given the same curing time and cement content, the higher the initial water content, the lower the compressive and flexural strength. After 60 days of curing, the compressive strength of marine silt bricks with cement content = 20% and water content = LL (liquid limit) reached approximately 5 MPa. The flexural strength was relatively low. The flexural strength of marine silt bricks with 20% cement and water content = LL was around 1.5 MPa. The compressive and flexural strength decreased with the increase of water/cement ratio. As for the curing time, longer curing time had a positive impact on the compressive strength. The ratio of flexural to compressive strength varied slightly in the range of 0.4–0.5.     

Experimental Investigation of Unconfined Compression Strength and Stiffness of Cement Treated Salt-Rich Clay

Soft clay with high sodium chloride salt concentration is a problem encountered by geotechnical and highway engineers. Chemical stabilization using cement is an attractive method to improve the engineering properties of soft soil. However, very limited studies have been conducted to reveal the effect of salt concentration on the engineering properties of cement-stabilized soil and the reported results in literature are not consistent. The impact of sodium chloride salt on the strength and stiffness properties of cement-stabilized Lianyungang marine clay is studied in this study. The clay with various sodium chloride salt concentrations was prepared artificially and stabilized by various contents of Ordinary Portland cement. A series of unconfined compressive strength (UCS) tests of cement stabilized clay specimen after 7, 14, and 28 days curing periods were carried out. The results indicate that a high sodium chloride salt concentration has a detrimental effect on the UCS and stiffness of cement-stabilized clay. The detrimental effect of salt concentration on the strength and stiffness of cement-stabilized clay directly relates to cement content. Soils mixed with high cement content are more resistant to the negative effect of salts than soils mixed with low cement content. The ratio of modulus of elasticity to UCS of cement treated soil does not have an obvious relationship with salt concentration. The findings of this study present a rational basis for the understanding of the impact of salt on the engineering properties of cement-treated soil.     

Assessment of Unconfined Compressive Strength of Cement Stabilized Marine Clay

Two aspects of deep mixing method, the difference relating strength gain in dry jet mixing (DJM, reagent powder introduced into the ground) and cement deep mixing (CDM, reagent slurry introduced into the ground), and prediction of unconfined compressive strength of cement stabilized marine clay, are discussed in this paper. The first part of this paper concentrates on the difference between DJM and CDM on strength gain, and suggests a guideline for DJM and CDM selection. An indicator in terms of water content ratio, which is defined as the ratio of water content to the liquid limit of the soil, is presented by statistical analysis from the laboratory and field test data as a guideline for the selection of DJM or CDM. Based on the laboratory test data, a mathematical model relating strength gain of cement stabilized marine clay to related variables is developed. A new simple index designated as total water-cement ratio, which is defined as the ratio of water weight in the soil-cement to the weight of cement in dry state, is proposed for interpretation of test data of soil-cement. The proposed method is then verified with available test data published by other different researchers.     

Assessment of Unconfined Compressive Strength of Cement Stabilized Marine Clay

Two aspects of deep mixing method, the difference relating strength gain in dry jet mixing (DJM, reagent powder introduced into the ground) and cement deep mixing (CDM, reagent slurry introduced into the ground), and prediction of unconfined compressive strength of cement stabilized marine clay, are discussed in this paper. The first part of this paper concentrates on the difference between DJM and CDM on strength gain, and suggests a guideline for DJM and CDM selection. An indicator in terms of water content ratio, which is defined as the ratio of water content to the liquid limit of the soil, is presented by statistical analysis from the laboratory and field test data as a guideline for the selection of DJM or CDM. Based on the laboratory test data, a mathematical model relating strength gain of cement stabilized marine clay to related variables is developed. A new simple index designated as total water-cement ratio, which is defined as the ratio of water weight in the soil-cement to the weight of cement in dry state, is proposed for interpretation of test data of soil-cement. The proposed method is then verified with available test data published by other different researchers.     

Mechanical Characteristics of Light-Weighted Soils Using Dredged Materials

This study investigates the mechanical characteristics of light-weighted soils (LWS) consisting of expanded polystyrene (EPS), dredged clays, and cement through both unconfined and triaxial compression tests. The mechanical characteristics of the compressive strength of LWS are analyzed with varying initial water contents of dredged clays, EPS ratio, cement ratio, and curing pressure. In the triaxial compression test, it is found that the compressive strength of LWS associated with EPS is independent on the effective confining pressure. When both EPS ratio is less than 2% and cement ratio is more than 2%, the compressive strength rapidly decreases after the ultimate value. This signifies that the compressive strength-strain behavior is quite similar to that of the cemented soil. The ground improved by LWS has the compressive strength of 200 kPa associated with the optimized EPS ratio of 3-4% and initial water content of 165-175%. The ultimate compressive strength under both triaxial and unconfined compression tests is almost constant for a cement ratio of up to 2%.     

Mechanical Characteristics of Light-Weighted Soils Using Dredged Materials

This study investigates the mechanical characteristics of light-weighted soils (LWS) consisting of expanded polystyrene (EPS), dredged clays, and cement through both unconfined and triaxial compression tests. The mechanical characteristics of the compressive strength of LWS are analyzed with varying initial water contents of dredged clays, EPS ratio, cement ratio, and curing pressure. In the triaxial compression test, it is found that the compressive strength of LWS associated with EPS is independent on the effective confining pressure. When both EPS ratio is less than 2% and cement ratio is more than 2%, the compressive strength rapidly decreases after the ultimate value. This signifies that the compressive strength-strain behavior is quite similar to that of the cemented soil. The ground improved by LWS has the compressive strength of 200 kPa associated with the optimized EPS ratio of 3–4% and initial water content of 165–175%. The ultimate compressive strength under both triaxial and unconfined compression tests is almost constant for a cement ratio of up to 2%.     

Strength Sensitivity of Marine Ariake Clays

ABSTRACT

Natural Ariake clays are characterized by high sensitivity. In this study, the mechanism and the factors controlling undrained shear strengths of both undisturbed and remolded Ariake clays are discussed. A series of unconfined compressive tests were performed on undisturbed samples of natural Ariake clays. The remolded undrained shear strength is predicted using a quantitative expression derived from extensive data of remolded undrained shear strength for a number of soils compiled from resources in the literature. The sensitivity of natural Ariake clays derived from the ratio of half of unconfined compressive strength for undisturbed samples to remolded undrained shear strength is found to be affected by both natural water content and normalized water content that is defined as the ratio of natural water content to liquid limit. The smaller the natural water content, the higher the sensitivity is at the same normalized water content. At the same natural water content, the larger the normalized water content, the higher the sensitivity is.     

Experimental study on the unconfined compressive strength of carbon fiber reinforced clay soil

To study the effect and mechanism of carbon fiber reinforced clay, a series of unconfined compression tests for clay reinforced with carbon fiber have been performed under the conditions of controlled water content and dry density. The carbon fiber is mixed into soil with the quality percentage of 0.01, 0.02, 0.03, 0.05, 0.1, 0.15, 0.25, 0.35, and 0.5%, then a certain quality of water was added in the soil to achieve the optimum soil water content. Ten groups of samples were tested by the unconfined compression experiment. The results showed that the incorporation of carbon fiber elements can effectively improve the unconfined compressive strength and brittle failure mode of soil. The soil is strengthened at the beginning and then weakened with the increased incorporation of carbon fiber, the effect is especially significant when the mix percentage becomes 0.1%. The interaction at the interface between carbon fiber surface and soil matrix is analyzed by using scanning electron microscopy (SEM). It is found that the enhancement mechanisms of carbon fiber reinforced soil are one-dimensional reinforcement of a single carbon fiber thread and three-dimensional reinforcement caused by fiber network respectively.     

Strength Sensitivity of Marine Ariake Clays

Natural Ariake clays are characterized by high sensitivity. In this study, the mechanism and the factors controlling undrained shear strengths of both undisturbed and remolded Ariake clays are discussed. A series of unconfined compressive tests were performed on undisturbed samples of natural Ariake clays. The remolded undrained shear strength is predicted using a quantitative expression derived from extensive data of remolded undrained shear strength for a number of soils compiled from resources in the literature. The sensitivity of natural Ariake clays derived from the ratio of half of unconfined compressive strength for undisturbed samples to remolded undrained shear strength is found to be affected by both natural water content and normalized water content that is defined as the ratio of natural water content to liquid limit. The smaller the natural water content, the higher the sensitivity is at the same normalized water content. At the same natural water content, the larger the normalized water content, the higher the sensitivity is.     

Effects of fly ash and slag content on the solidification of river-dredged sludge

Abstract

River-dredged sludge has a high water content and minimal bearing capacity and strength. Adding cement, fly ash, and slag to dredged sludge as a combined curing agent can quickly reduce its water content and improve its strength. This study experimentally investigates the solidification effectiveness of different proportions of curing agents using methods including electron microscopy, particle size analysis, water ratio limit, and water content and direct shear tests. The water content and shear strength of different combined curing agents are obtained at different ages. We find that an optimum curing agent combination exists. With increases in fly ash and slag content, test results indicate that the water content of solidified sludge first decreases and then increases, whereas the shear strength first increases and then decreases, allowing an optimal combination curing agent to be obtained. When using industrial waste residue as curing agent, it is necessary to consider the negative effects of the curing agent to better control the dosage so as to achieve better curing effect.     

Strengthening of Soft Marine Clay Using Bioencapsulation

Dredged or excavated soft marine clay can be improved by mixing it with cement or lime. However, these treatments are usually expensive. It is shown in this paper that soft marine clay can be strengthened through a bioencapsulation method in which the shear strength of clay aggregates can be substantially increased after the aggregates are treated with urease-producing bacteria, calcium chloride, and urea. We found that the bioencapsulation had increased the unconfined compressive strength of marine clay aggregates with a size of 5 mm from almost zero to more than 2 MPa. The strength of the bioencapsulated clay aggregates decreases with the increase in the size of the aggregate when the size is greater than 5 mm.     

The tensile and swelling behavior of cement-stabilized marine clay reinforced with short waste fibers

Abstract

Short waste fibers are used to suppress the expansion and improve the tensile strength of cement-stabilized marine clay (CMC). The fiber-reinforced mechanism and characteristics are revealed by experimental and numerical methods. First, the curing effect of the CMC when adding a composite curing agent is observed by scanning electronic microscopy, as is the contact surface between the fiber and the matrix. Then, the expansion rate and the tensile strength of fiber-reinforced cement-stabilized marine clay (FCMC) are illustrated by an expansion experiment and a direct tensile experiment, respectively. The results show that the sample with the cement content of 0.1% and the fiber length of 10?mm is the best in terms of strength enhancement and expansion inhibition. Finally, the mechanism of fiber reinforcement is discussed following a single fiber pullout experiment and some comprehensive explanations are proposed to verify the results of the tensile experiment. A numerical simulation of a single fiber pullout from a matrix is established by using a cohesive contact model. The comparison between the numerical results and the experimental results shows that the two models can be in good agreement, indicating that the calculation model of the interaction between the fiber and the matrix is realistic.     

Numerical simulation of water content dependent undrained shear strength of clays

Abstract

A nonlinear mathematical model for estimating the water content dependent undrained shear strength of clayey soils was developed. Three types of clay mixtures (kaolinite, bentonite, and kaolinite-bentonite) were considered. The shear strength of the given soil samples was determined via torvane tests. Experimental results were compared with three numerical results: (i) the analytical function fit, (ii) modeling without the water content effect, and (iii) modeling with the water content effect using the Mohr-Coulomb (M-C) model. There was good agreement among the experimental, analytical, and numerical results with and without the water content effect in the fully softening zone. However, there was a large difference between the numerical results obtained from the developed model with and without the water content effect in the flow zone with a high liquidity index, because the shear strength may decrease significantly to low value in the case of an abrupt increase of the water content. The greatest advantage of the developed model is that it can simulate the reduction of the shear strength and shear band development under the high water content condition, which may trigger a large mobile mass movement.     

Strength Characteristics of the Cement-Stabilized Surface Layer in Dredged and Reclaimed Marine Clay,Korea

ABSTRACT

A series of tests in both laboratory and field were performed to investigate the engineering and mechanical properties, especially flexural strength, of cement-stabilized soils. The strength of cement-stabilized soils mainly depends on water-to-cement ratio and curing temperature. The higher curing temperature and the longer curing time, the higher strength in cement-stabilized soils generates. The high ratio of water-to-cement results in lower strength. The compressive strength observed in the field is similar to the strength in the laboratory. Field tests on a cement-stabilized soil layer indicate that the strength is significantly affected by the thickness of the improved layer, which is directly related to the moment of inertia. In addition, the failure shape observed in a cement-stabilized layer in the field looks likes a bending failure type, because the flexural tensile strength, rather than the compressive strength, mainly dominates the failure of cement-stabilized layer. The flexural tensile strength is closely related to the moment of inertia. Therefore, the flexural tensile strength should be considered for determining the thickness and strength in improvement of soft clay.     

Enhancing the mechanical properties of marine clay using cement solidification

Abstract

The use of soft clay and dredged marine clays as the construction material is challenging. This is because the high water content, high compressibility and low permeability of the clay causing the instability of ground and structure. This detrimental effect of soft clay can be improved by the cement solidification process, which is relatively cheap and efficient. This paper mainly focuses on the study of improvement on the mechanical behavior of cement mixed marine clay. The soil is reconstituted by using ordinary Portland cement of 5%, 10%, 15% and 20% by its mass. The study reveals that cementation of clay significantly improves the peak and residual strength of soil. Similarly, the primary yield stress of the soil is also improved from 16 to 275?kPa as cement content increases from 5% to 20%, respectively. By using statistical tools, the relationships between various parameters are established, which are very important to define the mechanical behavior of the clay. This study reveals that the yield surface of the solidified marine clay is not a smooth elliptical surface. Rather it is composed of two linear surfaces followed by a log-linear surface which can be modeled by using simple parameters obtained from triaxial tests.     

Effect of Sample Disturbance on Unconfined Compression Strength of Natural Marine Clays

1 .IntroductionCoastalstructuresoftenencountersettlementandstabilityproblemsofsoftmarinefoundation (Liuetal.,1 999;Zhouetal.,2 0 0 0 ;Liuetal.,2 0 0 3) .Manyresearchershaveillustratedthatnaturalmarineclaysaregenerallysubjectedtotheeffectsofsoilstructureduringtheirdepositionalandpost depositionalprocesses (Zhangetal.,1 995;Hongetal.,2 0 0 3a ;2 0 0 3b) .Thesoilstructureofnat uralmarineclaysiseasilydamagedduringsamplingandhandlingbecausenaturalmarineclaysgeneral lyhavehighwatercontentandlowsti…     

Properties of sediments deposited in a fluid with different pH

Abstract

The effect of pH on the physical and mechanical properties of a sediment was investigated through a set of experimental tests. The sediment was formed from deposition of suspended particles in a fluid. Two different types of clay soil were suspended in fluids with different pH (2, 4, 7, 9 and 11) in cylindrical tubes with volume of 1?liter and also in special cylindrical reservoirs. The height of the sediment was measured in the cylindrical tube until equilibrium was achieved. The sediment deposited in the reservoirs was dried in air and then Atterberg limit, compaction and unconfined compressive strength (UCS) tests were conducted on samples prepared from each sediment. The results showed that the final height of the settled sediment is a function of pH; the height of sediment is increased with increasing the pH. Also, the Atterberg limits increased with increasing the pH. The maximum dry unit weight and optimum water content decreased and increased with increasing the pH. The final strength of the sediment decreased with increasing pH. Based on the SEM analysis, it was found that the values of pH influence the properties of the formed sediments.