Implementation of state-dependent plasticity model in strain wedge model for laterally loaded piles in sand

ABSTRACT

The strain wedge model effectively performs nonlinear analyses of the lateral response of piles by using a nonlinear stress-strain relationship to describe soil behavior in the strain wedge. In this study, a state-dependent plasticity model has been implemented in the strain wedge model to calculate the stress-strain relationship for sand in the strain wedge. To complement this implementation, the effect of dilatancy on the shear strain is considered in the strain wedge. A full-scale test and a 45 g centrifuge model test on laterally loaded piles are used to validate the proposed method. The results show that the deflections and moments predicted by the proposed method accord well with those measured from full-scale and centrifugal model pile tests. Moreover, the combination of the state-dependent plasticity model and the strain wedge model allows for analyzing the lateral response of single piles using a unique set of model parameters for different relative densities of sands. In addtion, the stress-strain response in the strain wedge, not the dilatancy, dominates the soil resistance in the strain wedge and thus the lateral response of piles.     

Lateral loading of a pile using strain wedge model and its application under scouring

The scour hole around a pile will reduce the capacity of a laterally loaded pile. The strain wedge model is capable to derive a p–y curve for the analysis of a lateral loaded pile on a nonlinear Winkler foundation. To improve and extend the ability of the strain wedge method, a modified strain wedge (MSW) method is developed, in which a nonlinear lateral deflection of the pile is assumed to describe the varied soil strain distribution in the passive wedge. And then by treating the soil weight involved in the strain wedge as a vertical load at the bottom of the scour hole, an equivalent wedge depth is obtained to consider the effect of scour hole dimensions on the response of laterally loaded piles in sand. The validity of the MSW model is proved by comparisons with a centrifuge test without scour. And its applicability in the problem of a pile with scour is performed by a comparison with a model test and a FE analysis. The analysis shows the pile displacement at the pile head with scour can be obtained by multiplying the corresponding deflection without scour with an amplification factor related to scour depth at large load level.     

Shaft capacity of pre-bored grouted planted nodular pile under various overburden pressures in dense sand

Abstract

This paper presents the results of a series of model tests performed to study the shaft capacity of pre-bored grouted planted nodular (PGPN) pile in dense sand. The influence of the vertical overburden pressure on the shaft capacity of the PGPN pile is also investigated based on the test results. The test piles were equipped with strain gauges to measure the axial loads during the loading process, moreover, a foam plate was buried beneath pile tip to eliminate the influence of tip resistance on the shaft capacity. Some conclusions can be drawn based on the test results: the peak skin friction of PGPN pile increases with the increase of vertical overburden pressure applied on the foundation soil, while the rate of increase decreases with the increasing overburden pressure; the surface of the pile–soil interface of PGPN pile is relatively rough, and significant dilatant increase in lateral stress occurs during the loading process.     

Axial compressive bearing capacity of piles in ‎oil-contaminated sandy soil using FCV

ABSTRACT

Oil and its derivatives contaminate many soils and not only affect their chemical and biological properties but also their geotechnical properties. As oil contamination may deteriorate the functioning of piles, this paper addresses the effects of oil contamination on soil–pile interactions. Axial compressive bearing capacities of two close-ended, instrumented piles were investigated in different oil-contaminated sand using frustum confining vessel. Three different oils (gasoil, crude oil, and used motor oil) at different contamination levels were considered and using some strain gauges, the toe, shaft, and the net total bearing capacity of piles, as well as load distributions along the pile length, were derived. The results show that the presence of oil between soil particles has considerable adverse effects on bearing capacities of model piles, especially the shaft bearing capacity. The oil viscosity and percentage, as well as the contaminated sand bed thickness around the piles, are the most influential parameters. The higher the oil viscosity and oil content, the lower the values of the piles’ bearing capacities in comparison to the uncontaminated sand. With some modifications on the bearing capacity parameters of CFEM method, a good agreement was observed between measured and calculated bearing capacity values.     

Study of dilatancy behaviors of calcareous soils in a triaxial test

Abstract

In this article, the dilatancy of calcareous soil is studied systematically based on triaxial consolidation drainage shear tests, and the difference in dilatancy between calcareous soil and siliceous soil is also investigated. It was found that: ① Calcareous soil experience obvious dilated deformation. Dilatancy tendency increases with increasing related density and decreases with increasing confining pressure. ② The volumetric strain rate initially increases from negative to positive. After it reaches a maximum, there is a small decrease in the volumetric strain rate, but it is still greater than zero, and the stress-strain curves are of softening type. ③ For the same condition, the dilatancy deformation of calcareous sand begins later than that of siliceous sand, and the volume compression before dilatancy is also larger for calcareous sand. ④ The critical state alone cannot accurately describe the entire deformation process of soil, and it is proposed that the phase transformation state be added to the standard method used to assess soil dilatation and contraction. ⑤ Based on the statistical analysis of experimental data, mathematical relationships were established between void ratio, relative density, and effective confining pressure of phase transformation state and critical state, respectively.

• Highlights

• Reports results from a well-designed experiment that includes a good amount of samples and data.

• Effects of relative density and effective confining pressure on deformation mode and mechanical properties of calcareous sand are evaluated.

• The difference in dilatancy between calcareous sand and siliceous sand was compared

• The phase-transformation state and critical state were compared with the axial strain, volumetric strain and deviatoric stress.

• Using phase-transformation void ratio and critical void ratio to describe the whole deformation process of calcareous sand is proposed.

• The mathematical expressions of phase-transformation void ratio and critical void ration were given, respectively.

     

Comparison Between Shear Behaviors of Overconsolidated Nakdong River Sandy Silt and Silty Sand

From this research, overconsolidated undrained and drained behaviors of specimens with high sand content were highly dilatant. According to the comparison results of laboratory tests, the deviator stresses of silty sand were greater than sandy silt due to high sand content under increasing OCRs, and both silty sand and sandy silt were presented strain softening tendency after failure under undrained loading. The pore water pressure increased with increasing fines content under increasing OCRs. Silty sand exhibited more dilatancy and increasing shear strength than sandy silt because pore water pressures of silty sand were lower than sandy silt under higher OCRs. In overconsolidated drained tests, silty sand is higher strength than sandy silt because silty sand has a lower volumetric strain and higher deviator stress than sandy silt under increasing OCRs. As the degree of overconsolidation increased, similar behaviors of silty sand and sandy silt observed that volumetric strain decreased to negative values due to dilatancy effect and low-cohesion under current effective confining pressures.     

Role of piles in mitigating the movement of pipes in soft grounds during embankment loading

Abstract

Pipes buried in soft ground can be damaged due to the vertical and lateral movement of the ground during the construction of the embankment. To investigate such a movement of the soft ground, full-scale tests using embankment piles and stabilizing piles were conducted for 70?days. A pile-supported embankment has been used to reduce the deformation of soft ground by transferring the embankment load through piles to the firm layer below the soft ground, whereas stabilizing piles have been employed to resist the lateral earth pressure that is induced in soft ground by embankment loads. The Coupling Area (CA), which was defined as the quantitative index to determine the resistance effect of both settlement and lateral flow of the soft ground when the embankment was reinforced, is adapted. The analysis results of the CA indicate that the piled embankment was more effective for preventing the damage to buried pipe installed near the embankment, while the stabilizing piles had almost the same effect as the piled embankment when the pipe was buried far away from the embankment.     

Model tests on open-ended concrete pipe piles jacked in sand

Abstract

An experimental study of the performance of concrete pipe piles during installation under different penetration speeds and static load tests on the piles in sand is presented. The applied jacking force, the amount of pile penetration, length of soil plug formed and ultimate bearing capacity were measured during the model tests. The results showed that the concrete pipe piles were partially plugged and the behavior of the soil plug was significantly affected by the penetration speed. The lower the penetration speed, the larger the soil plug formed which in turn leads to a greater ultimate bearing capacity. The size of soil plug can be evaluated by the m value defined as the ratio of the volume of the soil plug to that of the penetrated pile wall. The relationship between the m value and the penetration speeds can be used to estimate the amount of soil plug and the depth of penetration for an open-ended concrete pipe pile jacked into sand.     

Centrifuge modeling of single pile response due to lateral cyclic loading in kaolin clay

In offshore engineering, pile foundations are commonly constructed in marine deposits to support various structures such as offshore platforms. These piles are subjected to lateral cyclic loading due to wind, wave action, and drag load from ships. In this paper, centrifuge model tests are conducted to investigate the response of the existing single piles due to lateral cyclic loading. The cyclic loading was simulated by a hydraulic actuator. It is found that the residual lateral movement and bending strain are induced in the existing pile after each loading–unloading cycle. This is because plastic deformation is induced in the soil surrounding the existing pile during each loading–unloading cycle. By increasing the applied loads during cyclic loading–unloading process, the lateral movements and bending strains induced in the pile head increase simultaneously. As the cyclic loading varies from 10 to 50 kN, the residual pile head movement increases from 40 to 154?mm, and the residual bending strain of the existing pile varies from 100 to 260 με. The ratio of residual to the maximum pile head movements varies from 0.17 to 0.22, while the ratio of residual to the maximum bending strains is in a range of 0.12–0.55.     

Behavior of Loose Silty Sand of Chlef River: Effect of Low Plastic Fine Contents and Other Parameters

This article presents a laboratory study of static behavior of silty-sand soils. The objective of this laboratory investigation is to study the effect of initial confining pressures and fines content on the undrained shear strength (known as liquefaction resistance) response, pore pressure, and hydraulic conductivity of sand–silt mixtures. The triaxial tests were conducted on reconstituted saturated silty-sand samples at initial relative density D_r = 15% with fines content ranging from 0 to 50%. All the samples were subjected to a range of initial confining pressures (50, 100, and 200 kPa). The obtained results indicate that the presence of low plastic fines in sand–silt mixture leads to a more compressible soil fabric, and consequently to a significant loss in the soil resistance to liquefaction. The evaluation of the data indicates that the undrained shear strength can be correlated to fines content (F_c), inter-granular void ratio (e_g), and excess of pore pressure (Δu). The undrained shear strength decreases with the decrease of saturated hydraulic conductivity and the increase of fines content for all confining pressures under consideration. There is a relatively high degree of correlation between the peak shear strength (q_peak) and the logarithm of the saturated hydraulic conductivity (k_sat) for all confining pressures.     

Undrained Monotonic Response and Instability of Medium-Dense Sandy Soil

A series of undrained monotonic triaxial compression tests were performed on natural, medium-dense (relative density (RD) = 50%) Chlef sand containing 0.5% of non-plastic fines, under different confining pressures of 50 kPa, 100 kPa, and 200 kPa. This article focuses on distinctive states of the monotonic undrained response of sands, namely the critical state, the phase transformation state, the quasi-steady state, and the state of undrained instability (onset of flow liquefaction). Specimens were prepared using dry funnel pluviation and wet deposition to investigate the effect of the initial sand fabric on these states. The present data suggest that the initial fabric of the sand appears to have a significant effect on the undrained behavior in the early stages of shearing, with its influence vanishing at large strains. Wet deposition specimens demonstrate considerably larger undrained instability state strength than their dry funnel pluviation counterparts, and a unique critical state locus is reached by both dry funnel pluviation and wet deposition.     

Laboratory Study on the Hydraulic Conductivity and Pore Pressure of Sand-Silt Mixtures

The hydraulic conductivity plays a major role on the excess pore pressure generation during monotonic and cyclic loading of granular soils with fines. This paper aims to determine how much the hydraulic conductivity and pore pressure response of the sand-silt mixtures are affected by the percentage of fines and void ratio of the soil. The results of flexible wall permeameter and undrained monotonic triaxial tests performed on samples reconstituted from Chlef River sand with 0, 10, 20, 30, 40, and 50% nonplastic silt at an effective confining stress of 100 kPa and two relative densities (D_r = 20, and 91%) are presented and discussed. It was found that the pore pressure increases linearly with the increase of the fines content and logarithmically with the increase of the intergranular void ratio. The results obtained from this study reveal that the saturated hydraulic conductivity (k) of the sand mixed with 50% low plastic fines can be, on average, four orders of magnitude smaller than that of the clean sand. The results show also that the hydraulic conductivity decreases hyperbolically with the increase of the fines content and the intergranular void ratio.     

Simplified analysis of offshore piles under cyclic lateral loads

A simple theory for predicting the response to cyclic lateral loading of piles deeply driven in either soft clay or sand is presented and formulas given for calculating, among other things, deflection and internal bending moment along the pile. The theory assumes the soil resistance to deflection to be characterized by an initial elastic reaction up to a critical deflection level, followed by a yield reaction independent of further deflection. Soil parameters are estimated and the theory is shown to provide good correlation with existing field data.     

Degradation of lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading

Abstract

In this article, the degradation of the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading is studied numerically. A modified kinematic hardening constitutive model is employed to simulate the degradation of soft clay after cyclic loading. The modified model is verified by comparing the numerical simulation results with the results of centrifuge model tests. Furthermore, the modified model is applied to numerical simulations for evaluating the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading. The degradation of the lateral bearing capacity of piles in soft clay after different cyclic displacement levels and different numbers of cycles is investigated. The study reveals that the modified kinematic hardening constitutive model can effectively estimate the cyclic degradation behavior of piles in soft clay subjected to cyclic lateral loading. The degradation of the ultimate lateral bearing capacity progresses slowly with increasing cyclic displacement level for fewer cycles, and the degradation develops significantly at higher levels of cyclic displacement after applying a larger number of cycles.     

Influence on lateral rigidity of offshore piles using proposed p–y curves

A fundamental study of pile–soil systems subjected to lateral loads in offshore deposit was conducted using experimental tests and numerical analysis. The emphasis was on the soil–pile rigidity of a laterally loaded pile in marine clay. Rigid- and flexible-pile analyses were conducted for comparison. A framework for determining the lateral load transfer curve (p–y curves) is proposed based on both field and laboratory model tests. A numerical analysis that takes into account the proposed p–y curves was performed for the pile flexibility parameters such as pile diameter, pile length, pile-bending stiffness, and the modulus of subgrade reaction. Based on the analysis, it is shown that the differences in bending moment and lateral displacement are more significant for flexible piles rather than rigid piles. It was found that the p–y curves influence the behavior of flexible piles more than rigid piles, thus the magnitude and distribution of the p–y curves are significantly important in flexible pile design.     

Centrifuge modelling of lateral loading behaviour of a “semi-rigid” Mono-pile in soft clay

Abstract

Mono-pile foundations have been widely used for offshore wind turbines principally due to their convenient construction and cost-effective nature. So far, little attention has been paid to large diameter “semi-rigid” piles that have distinct behaviours from flexible or ideally rigid piles. This paper presents a series of centrifuge model tests to study the deforming and bearing characteristics of a 5.9 dia. semi-rigid pile under lateral loadings in kaolin clay. For monotonic loading, a modified p–y curve analysis model considering rotational soil flow near the rotation centre of pile was proposed, highlighting the limitation of classic plane-strain based plasticity models to evaluate the ultimate lateral pile-soil resistance. For cyclic loading, a strong correlation between the degree of soil degradation and cyclic load amplitude was identified. Besides, a degradation factor model, accounting for various cyclic stress levels and soil depths, was proposed, which can be used to assess the accumulative displacement of semi-rigid piles under cyclic loadings in soft clay.     

Evaluation of liquefaction potential of marine sandy soil with piles considering nonlinear seismic soil–pile interaction; A simple predictive model

Abstract

An elastoplastic, dynamic, finite-difference method was applied to study the effects of nonlinear seismic soil–pile interaction on the liquefaction potential of marine sand with piles. The developed model was well validated using the centrifuge test. The results showed that acceleration, bending moment, and excess pore water pressure complied well with centrifuge test results. The effect of different affecting parameters on liquefaction potential was investigated using parametric study. Using a sensitivity analysis, the pile embedment parameter was shown to be the most influential parameter. Finally, applying the evolutionary polynomial regression technique, a new model for predicting the liquefaction potential was presented.     

Bearing Behavior of Cast-in-Place Expansive Concrete Pile in Coral Sand Under Vertical Loading

The low side friction of piles in coral sand results in the low bearing capacity of foundations. In this paper, expansive concrete pile is utilized to improve the bearing capacity of pile foundations in coral sand. Both model tests and numerical simulation are performed to reveal the bearing mechanism of expansive concrete pile in coral sand.Results showed that the lateral earth pressure near pile increases obviously and the side friction of piles is improved,after adding expansion agent to the concrete. The horizontal linear expansion is 1.11% and the bearing capacity increased 41% for the pile, when 25% expansion agent is added. Results in finite element numerical simulation also show that ultimate bearing capacity increases with the increase of the linear expansion ratio. Besides, the area for obvious increase in side friction is below the surface of soil about three times the pile diameter, and the expansion leads to a high side friction sharing of the pile. Therefore, the cast-in-place expansive concrete pile is effective in improving the bearing capacity of piles in coral sand.     

Experimental simple shear study of composite soil with cemented soil core

Abstract

Cement soil mixing piles are an effective treatment method for marine soft clay. To investigate the static and dynamic characteristics of the composite soil with cemented soil core, a series of experiments are carried out by using the cyclic simple shear test. The result shows that, the static shear strain showed strain hardening, cemented soil core can improve static shear strength of composite soil, vertical stress can enlarge reinforcement of cemented soil core. The tendency of strain development of composite soil with different area replacement ratios under cyclic loading is the same as that of pure clay, existing critical cyclic stress ratios corresponding to different area replacement ratios. In addition, improving area replacement ratio can increase cyclic strength. At same time, adding of cemented soil core does not change shape of hysteresis curve compared with it for clay either. Moreover, cemented soil core can also obstruct stiffness softening. Through regression analysis of the experimental data, relationship between cyclic number and soil softening index is proved to be linear. The results can give a reference for the dynamic characters of the marine soft clay foundation with cement soil mixing piles.     

A Laboratory model study on the performance of lime pile application for marine soils

In this study, research was conducted to examine the performance of the lime pile application, a deep chemical stabilization method to improve the engineering characteristics of marine soil deposits. By using a laboratory-scale model, the marine soil sample was compacted into soil blocks in circular steel test tanks, with the installation of lime piles in them. An experimental program examined the effect of lime piles on physical and engineering properties of the soil in terms of curing periods and lime pile radial distances. Test results showed that clay fines, linear shrinkage, compressibility, and swelling pressure decreased, while permeability, preconsolidation pressure, and stiffness increased significantly with an increase in curing periods and within a close distance to the lime piles. Also, the electrical resistivity of the treated soils was examined to monitor the changes in their electrical properties. Finally, the correlation between the measured electrical resistivity and swell pressure values of the tested soils at different curing periods suggested that the electrical resistivity values can be used as a monitoring technique for deep chemical treatments of the subsurface soil.