首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 25 毫秒
1.
Abstract

Open‐pipe piles are widely used for offshore structures. During the initial stage of installation, soil enters the pile at a rate equal to the pile penetration. As penetration continues, the inner soil cylinder may develop sufficient frictional resistance to prevent further soil intrusion, causing the pile to become plugged. The open‐ended pile then assumes the penetration characteristics of a closed‐ended pile. The mode of pile penetration significantly alters the soil‐pile interaction during and after installation. This affects the ultimate static bearing capacity (mainly in granular materials), the time‐dependent pile capacity (in clays), and the dynamic behavior and analysis of the piles.

Following a summary demonstrating the effects of pile plugging, a review of the common view of offshore pile plugging is undertaken. The interpretation of plugging by referring to the average plug length has led to the erroneous conclusion that in most piles significant plugging action does not occur.

Establishment of an analogy between soil samplers and open‐ended piles enabled correct identification of plugging by referring to the incremental changes in plug length. Examination of case histories of plugging of offshore piles revealed that beyond a certain penetration depth‐to‐diameter ratio, most piles are plugged.  相似文献   

2.
大直径超长桩的可打入分析是海洋平台打桩施工顺利进行的重要保障,土塞是否闭合的判断对于桩基可打入性分析具有较大的影响,因此,合理准确的土塞判断结果对提高桩的可打入分析的准确性具有重要的意义。以现场静力触探(CPTU)试验数据为依据,采用孔扩张理论推导了基于CPTU测试结果的桩端土的极限承载力计算公式;在求解桩端土体承载力时考虑了管桩与土体的刚度差异,同时考虑到打桩过程中的土体扰动。采用Randolph推荐的方法得到了土塞阻力,将两者进行比较,进而判断土塞的状态。通过实际工程的实测数据,对各个土层的土塞状况进行了判别,并根据判别情况采用波动方程的方法对桩基的可打入性进行了分析,将预测结果和现场的打桩记录进行了比较。计算结果显示,提出的方法与实测结果更为接近,有效地提高了桩的可打入性的预测精度。  相似文献   

3.
The low side friction of piles in coral sand results in the low bearing capacity of foundations. In this paper, expansive concrete pile is utilized to improve the bearing capacity of pile foundations in coral sand. Both model tests and numerical simulation are performed to reveal the bearing mechanism of expansive concrete pile in coral sand.Results showed that the lateral earth pressure near pile increases obviously and the side friction of piles is improved,after adding expansion agent to the concrete. The horizontal linear expansion is 1.11% and the bearing capacity increased 41% for the pile, when 25% expansion agent is added. Results in finite element numerical simulation also show that ultimate bearing capacity increases with the increase of the linear expansion ratio. Besides, the area for obvious increase in side friction is below the surface of soil about three times the pile diameter, and the expansion leads to a high side friction sharing of the pile. Therefore, the cast-in-place expansive concrete pile is effective in improving the bearing capacity of piles in coral sand.  相似文献   

4.
Abstract

The performance of steel caisson during and after installation with different penetration velocities in medium dense sand is presented. The applied jacking forces, the amount of formed soil heave and bearing capacity were measured in the model tests. The influence of penetration velocities on jacking forces, soil heave and bearing capacity were also discussed in detail. The results indicated that the jacking forces for caisson in medium dense sands were significantly affected by the penetration velocity. The larger the penetration velocity, the more soil flowed into the caisson cavity during installation. This will lead to larger inner shaft resistance and in turn more jacking forces required for the same penetration depth. The height of soil heave during installation increases with penetration velocity. The m value calculated by the ratio of the volumes of the soil heave to that of the penetrated caisson wall can be used to evaluate the soil heave. The larger the applied velocity, the larger the m value and larger bearing capacity of caisson after installation. The relationship between the m value and penetration velocity can be used to control the soil heave for a steel caisson with a wall thickness to external diameter ratio of 4.2% in medium dense sand by jacking method.  相似文献   

5.
Large-scale field tests were conducted to study set-up effect in open-ended prestressed high-strength concrete pipe piles jacked into stratified soil. Four open-ended prestressed high-strength concrete pipe piles with 13 and 18 m in embedment depth were fully instrumented with fiber Bragg grating sensors and installed. Several restrike dynamic tests were performed on each test pile, with the time interval from 21.5 to 284 hours after installation. Static loading tests (SLTs) were later performed on each test pile at 408 hours after installation to substantiate the dynamic tests. Changes with time in pile bearing capacity and in the shaft and toe resistances were studied based on the results of the pile tests. The development of shaft resistance set-up in different layers was studied in particular. It was found that set-up effect in the shaft resistance is significant and the toe resistance increment was minor. The overall set-up factor of total bearing capacity was found to range from 0.09 to 0.53, and the set-up effect of friction pile is much larger than the end bearing pile. More significant set-up in shaft resistance was observed in fill and alluvium layer. The dimensionless set-up factor A for shaft resistance in marine deposits ranges from 0.5 to 1.43, and it contributes the most to the shaft resistance as the shaft resistance in marine deposits is higher.  相似文献   

6.
Calibration chamber tests were conducted on open‐ended model piles driven into dried siliceous sands with different soil conditions in order to clarify the effect of soil conditions on load transfer mechanism in the soil plug. The model pile used in the test series was devised so that the bearing capacity of an open‐ended pile could be measured as three components: outside shaft resistance, plug resistance, and tip resistance. Under the assumption that the unit shaft resistance due to pile‐soil plug interaction varies linearly near the pile tip, the plug resistance was estimated. The plug capacity, which was defined as the plug resistance at ultimate condition, is mainly dependent on the ambient lateral pressure and relative density. The length of wedged plug that transfers the load decreases with the decrease of relative density, but it is independent of the ambient pressure and penetration depth. Under several assumptions, the value of earth pressure coefficient in the soil plug can be calculated. It gradually reduces with increase in the longitudinal distance from the pile tip. At the bottom of the soil plug, it tends to decrease with increase in the penetration depth and relative density, and to increase with the increase of ambient pressure. This may be attributed to (1) the decrease of friction angle as a result of increase in the effective vertical stress, (2) the difference in the dilation degree of the soil plug during driving with ambient pressures, and (3) the difference in compaction degree of soil plug during driving with relative densities. Based on the test results, an empirical equation was suggested to compute the earth pressure coefficient to be used in the calculation of plug capacity using one‐dimensional analysis, and it produces proper plug capacities for all soil conditions.  相似文献   

7.
ABSTRACT

Oil and its derivatives contaminate many soils and not only affect their chemical and biological properties but also their geotechnical properties. As oil contamination may deteriorate the functioning of piles, this paper addresses the effects of oil contamination on soil–pile interactions. Axial compressive bearing capacities of two close-ended, instrumented piles were investigated in different oil-contaminated sand using frustum confining vessel. Three different oils (gasoil, crude oil, and used motor oil) at different contamination levels were considered and using some strain gauges, the toe, shaft, and the net total bearing capacity of piles, as well as load distributions along the pile length, were derived. The results show that the presence of oil between soil particles has considerable adverse effects on bearing capacities of model piles, especially the shaft bearing capacity. The oil viscosity and percentage, as well as the contaminated sand bed thickness around the piles, are the most influential parameters. The higher the oil viscosity and oil content, the lower the values of the piles’ bearing capacities in comparison to the uncontaminated sand. With some modifications on the bearing capacity parameters of CFEM method, a good agreement was observed between measured and calculated bearing capacity values.  相似文献   

8.
Piling procedure may disturb the surrounding soil, due to the installation particularly for cast-in-place piles. It causes a reduction in the soil strength parameters and, consequently, pile capacity. To overcome shortcomings and also for improving piles’ capacity, postgrouting as a compensation method is recognized and more developed in recent years. Helical piles, those are used widely in marine and land projects, although, are driven by torque implementation, but soil disturbance is noticed, where number of the helices become up to 3 and more. In this paper, an experimental study program is performed by frustum-confined vessel (FCV) to investigate bearing capacity of model helical piles and also postgrouted cases’ performance. FCV has been used because of its linear distribution of vertical and horizontal stresses from zero at top to maximum at bottom which simulates real field stress conditions. Through experimental study, small-scale helical model piles were made of 4-mm-thick steel plate and have been used with a length of 750?mm. The shaft and helix diameters of model piles have been 32 and 89?mm, respectively. So, the helix-to-shaft ratio (wing ratio) was about 2.8. The helical model piles installed in fine-grained sand as a surrounding soil and then axial loading tests before and after grouting were performed to achieve ultimate pile capacity. Results indicated postgrouting can improve both ratios of toe and frictional soil–pile interactions including upgrading β and Nt factors. In addition, the post grouting phenomena can change the pile geometry due to treated soil bond, resulting better functioning. Therefore, it is a proper method to improve helical piles performance and compensate installation effects in capacity mobilization.  相似文献   

9.
海上复杂地质条件下大直径钢管桩时效性试验研究   总被引:1,自引:1,他引:0  
通过对3根海上复杂地质条件下的大直径钢管桩采取高应变初打与不同休止时间复打相结合的试验方法,得到不同休止时间钢管桩承载力、侧阻力及端阻力大小,以此对不同桩侧土及持力层对钢管桩时效性的影响进行了研究。研究结果表明:1)钢管桩承载力时效性现象明显,且随时间增长迅速; 2)钢管桩侧阻力的恢复系数远大于端阻力; 3)桩侧黏性土强度的恢复是钢管桩侧阻力增加的主要原因; 4)砂土层虽提供的侧阻力较大,但其对侧阻力增长的贡献不如黏性土; 5)持力层越硬,端阻力与承载力的恢复性越差。  相似文献   

10.
Abstract

Mono-pile foundations have been widely used for offshore wind turbines principally due to their convenient construction and cost-effective nature. So far, little attention has been paid to large diameter “semi-rigid” piles that have distinct behaviours from flexible or ideally rigid piles. This paper presents a series of centrifuge model tests to study the deforming and bearing characteristics of a 5.9 dia. semi-rigid pile under lateral loadings in kaolin clay. For monotonic loading, a modified p–y curve analysis model considering rotational soil flow near the rotation centre of pile was proposed, highlighting the limitation of classic plane-strain based plasticity models to evaluate the ultimate lateral pile-soil resistance. For cyclic loading, a strong correlation between the degree of soil degradation and cyclic load amplitude was identified. Besides, a degradation factor model, accounting for various cyclic stress levels and soil depths, was proposed, which can be used to assess the accumulative displacement of semi-rigid piles under cyclic loadings in soft clay.  相似文献   

11.
螺旋桩芯劲性复合桩(helix stiffened cement mixing pile,简称HSCM桩)是一种新型复合桩,其成桩工艺会对桩身及其承载性能有较大影响。为验证HSCM桩在软黏土中同步旋进注浆工艺的可行性,并研究其成桩参数对抗压承载性能的影响,设计了2组缩尺模型试验,包括不同叶片数量与钻进速度的HSCM桩与对比螺旋桩。通过在高岭土制备的软黏土中成桩,并进行抗压承载性能及桩身几何尺寸测试,分析HSCM桩的成桩参数与水泥土桩身间的关系。试验结果表明:同步旋进注浆工艺能够在螺旋桩周围形成倒圆台状的水泥土桩身,水泥土桩身的平均黏结直径约为叶片直径的1.17~1.35倍;适当增加叶片数量能够使水泥与土体充分拌和,提高水泥土桩身的完整性与连续性,以改善HSCM桩的成桩质量;钻进速度大幅提高会导致注浆量不足,减小水泥土桩身的黏结直径与刚度;试验条件下HSCM桩的抗压极限承载力是螺旋桩的3.83~3.93倍,桩径扩大提高了侧摩阻力,注浆工艺加固并提高了土体强度,弥补了叶片在旋进过程中扰动土体造成强度降低的问题。  相似文献   

12.
Drilled displacement (DD) piles with a screw-shaped shaft (referred to as DD piles) are installed using a continuous full thread hollow rod (without a displacement body) inserted and advanced in the soil by both a vertical force and a torque. As a type of newly developed pile, current understanding of the bearing mechanism of DD piles is unsatisfactory, which restricts their further applications in engineering. The primary aim of this paper is to study the bearing mechanism of this type of pile using a numerical method. First, a numerical model for calculating the bearing capacity of the DD piles was created and validated by a laboratory test. Then, the effects of the parameters of pile–soil interface, soil strength, and pile geometrical parameters on the bearing mechanism of the DD piles were investigated in parametric studies. The results of parametric studies show that the limit shear stress on the pile–soil interface, the friction angle of surrounding sand, screw pitch, and thread width significantly influence the bearing capacity of the DD piles, whereas the friction coefficient at the pile–soil interface and the thread thickness have little effect. Based on the results of the parametric studies, the failure mechanism of the DD piles under vertical load is analyzed. Finally, an equation for predicting the ultimate bearing capacities of helical piles based on cylindrical shear failure was used for estimating the bearing capacity of the DD piles, and the calculated results were verified with the numerical results.  相似文献   

13.
This study has evaluated the vertical bearing capacity by conducting static load tests for noise-free and vibration-free screw pretensioned spun high-strength concrete (PHC) piles installed using two different methods (end-squirting shoe and pre-boring methods). Vertical bearing capacity differences seem to occur due to the displacement of soils near the external circumference of a pile, depending on the installation method. A method by which to evaluate the bearing capacity of screw concrete piles is suggested by considering the equations that already have been used to calculate the bearing capacity of piles. Based on static load tests and analysis, the pile installed using the end-squirting shoe method was assumed to be a bored pile and it was reasonable to use the equation proposed by the Japanese Geotechnical Society. At the same time, the pile installed using the pre-boring method was deemed a low soil displacement pile and so it was reasonable to apply the equations proposed for calculating the bearing capacity of the driven pile suggested by the Architectural Institute of Japan.  相似文献   

14.
一种新型钢管桩预装荷载箱法被研发出用于自平衡法海上风电钢管桩基检测试验,并通过现场自平衡试验研究探究了海上打入桩桩基础特性。该方法首次成功应用于海外某海上风电场直径1.4 m的超长大直径钢管桩承载力检测,用于探究其承载特性和桩侧桩端阻力发挥规律。现场试验显示,该新型检测方法达到了预期的测试效果和经济效益,与现有钢管桩自平衡法相比,对土的影响更小,可靠度更高,为类似土层和直径的超长钢管桩承载力试验提供了新的途径。  相似文献   

15.
Abstract

Pile foundation is the most popular option for the foundation of offshore wind turbines. The degradation of stiffness and bearing capacity of pile foundation induced by cyclic loading will be harmful for structure safety. In this article, a modified undrained elastic–plastic model considering the cyclic degradation of clay soil is proposed, and a simplified calculation method (SCM) based on shear displacement method is presented to calculate the axial degradated capacity of a single pile foundation for offshore wind turbines resisting cyclic loadings. The conception of plastic zone thickness Rp is introduced to obtain the function between accumulated plastic strain and displacement of soil around pile side. The axial ultimate capacity of single piles under axial cyclic loading calculated by this simplified analysis have a good consistency with the results from the finite element analysis, which verifies the accuracy and reliability of this method. As an instance, the behavior of pile foundation of an offshore wind farm under cyclic load is studied using the proposed numerical method and SCM. This simplified method may provide valuable reference for engineering design.  相似文献   

16.
利用室内半模试验和颗粒流数值模拟,揭示多层砂土地基扩底桩单桩抗压承载特性及变形特征。结果表明,通过对比分析极限承载力与H_h/D(持力层厚度与扩大头直径之比)的关系可以看出,单桩的抗压极限承载力随H_h/D逐渐增加,当H_h/D超过2.0时,极限承载力基本不再增加,此时的单桩抗压极限承载力稳定在300.01~303.25 N,是H_h/D=0.5时极限承载力(183.83 N)的1.65倍。扩大头下部土体发生局部压缩-剪切破坏,破坏面从扩大头底面边缘向斜下方扩展,在水平方向影响范围达到最大后逐渐向桩内侧收缩;荷载作用越大,地基破坏区域越大,相应的极限抗压承载力也越大;持力层厚度增加,扩大头分担的荷载比例增大,分担的荷载达到稳定需要的桩顶位移也越大,H_h=0.5 D试验扩大头分担的荷载比例稳定时为60%,对应的桩顶位移约为29 mm;桩顶位移达到33 mm后,H_h=1.0~3.0 D试验稳定在63%~65%之间;通过细观颗粒流理论对砂土移动特性的研究发现,持力层厚度从0.5 D增大至2.0 D,破坏面的起始扩展角度从31°增大至42°。数值模拟研究结果与模型试验数据吻合效果良好,证明该方法分析多层砂土地基扩底桩单桩抗压荷载传递机理是可行的。  相似文献   

17.
Abstract

In this article, the degradation of the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading is studied numerically. A modified kinematic hardening constitutive model is employed to simulate the degradation of soft clay after cyclic loading. The modified model is verified by comparing the numerical simulation results with the results of centrifuge model tests. Furthermore, the modified model is applied to numerical simulations for evaluating the lateral bearing capacity of piles in soft clay subjected to cyclic lateral loading. The degradation of the lateral bearing capacity of piles in soft clay after different cyclic displacement levels and different numbers of cycles is investigated. The study reveals that the modified kinematic hardening constitutive model can effectively estimate the cyclic degradation behavior of piles in soft clay subjected to cyclic lateral loading. The degradation of the ultimate lateral bearing capacity progresses slowly with increasing cyclic displacement level for fewer cycles, and the degradation develops significantly at higher levels of cyclic displacement after applying a larger number of cycles.  相似文献   

18.
Abstract

In onshore and offshore fields of ocean engineering, piles are used as foundation systems for various structures. Piles are classified into different types depending on their materials, geometries, and particularly, installation methods, which have advantages or limitations. Companies and engineers have developed a new group of piles, because of necessity to improve their performance in terms of increasing the bearing capacity, reducing impacts of traditional installation procedures, implementing by low- torque power equipment, and utilizing them in widely different ground conditions, including in a marine environment. In the present study, three different models of a new pile with an expander body are introduced to increase the shaft and pile-toe diameters and its self-expansion in the embedment depth under the titles of the Bubble pile (BP), Self-Expanded pile (SEP) and Wing pile (WP). The main subject of this research is to achieve increased bearing capacity, reduced installation effects, and decreased required installation torque. The frustum-confining vessel of Amirkabir University of Technology (FCV-AUT) was employed for this purpose. Up to 14 axial compressive and tensile load tests were carried out on different model piles on sand collected from Anzali shore located on the northern coast of Caspian Sea in Iran, with relative densities of 45% to 50% within FCV-AUT. Comparing the performance of introduced pile with traditional pile corresponding to the same characteristics, the results indicated a significant increase in the axial bearing capacity and reduced disturbance effect of the pile. Also, a lower installation torque of the SE pile was required compared to the helical pile. The test results also demonstrated that the new pile could resist considerable compressive and uplift loads, and could be a possible alternative to traditional piles in the onshore sector.  相似文献   

19.
Abstract

This paper presents the results of a series of model tests performed to study the shaft capacity of pre-bored grouted planted nodular (PGPN) pile in dense sand. The influence of the vertical overburden pressure on the shaft capacity of the PGPN pile is also investigated based on the test results. The test piles were equipped with strain gauges to measure the axial loads during the loading process, moreover, a foam plate was buried beneath pile tip to eliminate the influence of tip resistance on the shaft capacity. Some conclusions can be drawn based on the test results: the peak skin friction of PGPN pile increases with the increase of vertical overburden pressure applied on the foundation soil, while the rate of increase decreases with the increasing overburden pressure; the surface of the pile–soil interface of PGPN pile is relatively rough, and significant dilatant increase in lateral stress occurs during the loading process.  相似文献   

20.
Abstract

Land reclamation has increased significantly in the eastern coastal areas of China. The increased exploitation of offshore resources has made cast-in-situ piles more preferable in these regions. However, precise prediction of axial forces and shaft resistances of piles is particularly difficult because geological conditions are complex after the foundation is treated by vacuum preloading. In this study, two groups of cast-in-situ piles, each of which consisted of two piles installed in soft soil in Oufei Project, Wenzhou, China, were compared by conducting tests using the slow static loading method to evaluate the influence of applying vacuum preloading to deal with soft soil foundation on the vertical bearing capacities of the piles. Two piles were located in an untreated area, while the other two were located in a vacuum preloading treating area. All the piles had the same length and diameter. In addition, the axial forces and shaft resistances of piles were calculated based on the measured strains. The field tests revealed that the ultimate bearing capacities and shaft resistances of test piles were significantly improved compared to those of the piles in untreated area. The experimental results presented in this study are expected to be highly beneficial for practical engineering.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号