Influence of colloidal silica grout on liquefaction potential and cyclic undrained behavior of loose sand

Cyclic triaxial tests were performed to investigate the influence of colloidal silica grout on the deformation properties of saturated loose sand. Distinctly different deformation properties were observed between grouted and ungrouted samples. Untreated samples developed very little axial strain prior to the onset of liquefaction. However, once liquefaction was triggered, large strains occurred rapidly and the samples collapsed within a few additional loading cycles. In contrast, grouted sand samples experienced very little strain during cyclic loading. Additionally, the strain accumulated uniformly throughout loading rather than rapidly prior to collapse and the samples never collapsed. Cyclic triaxial tests were done on samples stabilized with colloidal silica at concentrations of 5, 10, 15, and 20%. In general, samples stabilized with higher concentrations of colloidal silica experienced very little strain during cyclic loading. Sands stabilized with lower concentrations tolerated cyclic loading well, but experienced slightly more strain. Thus, treatment with colloidal silica grout significantly increased the deformation resistance of loose sand to cyclic loading.     

A critical state interpretation for the cyclic liquefaction resistance of silty sands

Contrary to many laboratory investigations, common empirical correlations from in situ tests consider that the increase in the percentage of fines leads to an increase of the cyclic liquefaction resistance of sands. This paper draws upon the integrated Critical State Soil Mechanics framework in order to study this seemingly not univocal effect. Firstly the effect of fines on the Critical State Line (CSL) is studied through a statistical analysis of a large data set of published monotonic triaxial tests. The results show that increasing the content of non-plastic fines practically leads to a clockwise rotation of the CSL in (e–ln p) space. The implication of this effect on cyclic liquefaction resistance is subsequently evaluated with the aid of a properly calibrated critical state elasto-plastic constitutive model, as well as a large number of published experimental results and in situ empirical correlations. Both sets of data show clearly that a fines content, less than about 30% by weight, may prove beneficial at relatively small effective stresses (p₀<50–70 kPa), such as the in situ stresses prevailing in most liquefaction case studies, and detrimental at larger confining stresses, i.e. the stresses usually considered in laboratory tests. To the extent of these findings, a correction factor is proposed for the practical evaluation of liquefaction resistance in terms of the fines content and the mean effective confining stress.     

Requirements for soil-specific correlation between shear wave velocity and liquefaction resistance of sands

The application of the simplified method for evaluating the liquefaction potential based on shear wave velocity measurements has increased substantially due to its advantages, especially for microzonation of liquefaction potential. In the simplified method, a curve is proposed to correlate the cyclic resistance ratio (CRR) with overburden stress-corrected shear wave velocity (V_s1). However, the uniqueness of this curve for all types of soils is questionable. The objective of this research is to study whether the correlation between CRR and V_s1 is unique or not. Besides, the necessity of developing the soil-specific correlations is also investigated. Based on laboratory test data, a new semi-empirical method is proposed to establish the soil-specific CRR–V_s1 correlation. To validate the proposed method, a number of undrained cyclic triaxial tests along with bender element tests were performed on two types of sands. Similar experimental data for six other types of sands reported in the literature was also compiled. Applying the proposed method, soil-specific CRR–V_s1 correlation curves were developed for these eight types of sands. It is shown that the correlation is not unique for different types of sands and the boundary curve proposed in the available simplified method can only be used as an initial estimation of liquefaction resistance. Finally, using the results of this study as well as previous ones, a chart is suggested to be used in engineering practice showing the conditions for which a detailed soil-specific CRR–V_s1 correlation study needs to be performed.     

Liquefaction behaviour of loose and compacted pond ash

Most of the ash produced all over the world is primarily disposed off by wet disposal method onto the ash ponds, which are occupying huge valuable lands. This disposal problem can be minimized by utilizing ash in large geotechnical earthworks. However, its use in earthquake prone areas requires thorough understanding of its liquefaction resistance and nature of development of excess pore pressures under dynamic loading conditions. Investigations have been carried out in this paper on the liquefaction behaviour of pond ash by conducting cyclic triaxial tests on inflow and outflow ash samples collected from two different ash ponds. Distinctly different liquefaction phenomenon was observed for the ash samples from inflow and outflow points of the same ash pond. Inflow samples exhibited higher cyclic resistance than outflow samples and their strengths were comparable with the natural sands. Further studies revealed that the influence of various factors on liquefaction susceptibility of both the types of ashes is similar to that of natural sands.     

An experimental study of the liquefaction strength of silty sands in terms of the state parameter

An elaborate program of monotonic and cyclic triaxial laboratory tests on mixtures of sand and silt with fines content 0%, 15% and 25% was performed to investigate the effect of density, consolidation stress and non-plastic fines on the liquefaction strength. The monotonic tests illustrated that the critical state lines of all mixtures do not cross each other, and are, approximately, parallel to each other. The results of the cyclic tests illustrated that the relationship between the cyclic strength and the state parameter does not depend on the consolidation stress, the soil density and the silt content. Analysis in terms of the state parameter showed that: (i) as the consolidation stress increases, the cyclic strength decreases and this effect is more pronounced as the specimens become denser, especially as the fines content increases and (ii) the cyclic strength decreases as the fines content increases and this effect is more pronounced as the specimens become denser.     

Cyclic and post-cyclic monotonic behavior of Adapazari soils

The August 17, 1999 Kocaeli earthquake affected the city of Adapazari, which is located in the northwest of Turkey, with severe liquefaction and bearing capacity failures causing tilting of buildings, excessive settlements and lateral displacements. To understand the stress–strain behavior and pore pressure behavior of undisturbed soils during the earthquake, the cyclic and post-cyclic shear strength tests have been conducted on soil samples obtained from Adapazari in a cyclic triaxial test system within the scope of this research. Cyclic tests have been conducted under stress controlled and undrained conditions. Post-cyclic monotonic tests have been conducted following cyclic tests. The strength curves obtained in the experiments showed that the dynamic resistance of silty sand was found to be 45% lower than those of high plasticity soils (MH). The strength of clayey soils with the plasticity index of PI=15–16% was lower compared to the strength of high plasticity soils. Also, it was observed that silty sand soils had the lowest strength. The dynamic strength of the soils increased with the increase in plasticity.     

The cyclic behaviour of soils and effects of geotechnical factors in microzonation

Geotechnical site conditions that can be very different due to changes in thickness and properties of soil layers, depth of bedrock and water table are among the main factors controlling earthquake characteristics on the ground surface. Soil layers subjected to cyclic stresses may lead to degradation of stress–strain and shear strength properties. The laboratory tests were conducted to evaluate the changes in the stress–strain and shear strength characteristics in terms of threshold cyclic shear stresses and cyclic yield stress. The effects of local site conditions are assessed based on geotechnical site conditions and earthquake source characteristics.     

Computation of degradation factors of p-y curves in liquefiable soils for analysis of piles using three-dimensional finite-element model

This paper presents a procedure to compute the values of degradation factors of p-y curves in the pseudo-static analysis of piles in liquefiable soils. Three-dimensional finite-element model was used for the computation of p and y values using OpenSees computer package. The piles were modeled using beam-column elements and elastic section. The soil continuum was modeled using brick elements and a two-surface plasticity model. By comparing the results of models in two cases of liquefiable and non-liquefiable, values of degradation factors were obtained. Validation of the degradation factors computed was conducted through the centrifuge test results. The simulation results showed a similar trend between degradation factor variation in different densities and sands. With increasing depth, the degradation factor increased. By comparing the results of pseudo-static analysis with the centrifuge test results, it was concluded that the use of the p-y curves with computed degradation factors in liquefiable sand gave reasonable results.     

A simplified method for unified buckling and free vibration analysis of pile-supported structures in seismically liquefiable soils

In seismic-prone zones with liquefiable deposit piles are routinely used to support structures (buildings/bridges). In this paper, a unified buckling and dynamic approach is taken to characterize this vibration. The pile–soil system is modelled as Euler–Bernoulli beam resting against an elastic support with axial load and a pile head mass with rotary inertia. The emphasis here is to obtain a simple expression that can be used by practicing engineers to obtain the fundamental frequency of the structure–pile–soil system. An approximate method based on an equivalent single-degree-of-freedom model has been proposed. Natural frequencies obtained from the exact analytical method are compared with approximate results. Proposed expressions are general as they are functions of non-dimensional parameters. It is shown that this simplified method captures the essential design features such as: (a) the continuous reduction of the first natural frequency of the structure–pile–soil system due to progressive reduction of soil stiffness due to liquefaction; (b) the reduction in the axial load-carrying capacity of the pile due to instability caused by liquefaction. The results derived in this paper have the potential to be directly applied in practice due to their simple yet general nature. An example problem has been taken to demonstrate the application of the method.     

Numerical modelling of the transverse dynamic behaviour of circular tunnels in clayey soils

In this paper, different approaches aimed at investigating the dynamic behaviour of circular tunnels in the transverse direction are presented. The analysed cases refer to a shallow tunnel built in two different clayey deposits. The adopted approaches include 1D numerical analyses performed modelling the soil as a single-phase visco-elastic non-linear medium, the results of which are then used to evaluate the input data for selected analytical solutions proposed in the literature (uncoupled approach), and 2D fully coupled FE simulations adopting visco-elastic and visco-elasto-plastic effective stress models for the soil (coupled approach). The results are proposed in terms of seismic-induced loads in the transverse direction of the tunnel lining. The different constitutive hypotheses adopted in the coupled numerical approach prove to play a significant role on the results. In particular, the plasticity-based analyses indicate that a seismic event can produce a substantial modification of loads acting in the lining, leading to permanent increments of both hoop force and bending moment.     

1st Ishihara Lecture: An overview of the behavior of pile foundations in liquefiable and non-liquefiable soils during earthquake excitation

The seismic response of a pile foundation is usually analyzed by approximate methods in practice. These methods typically neglect one or more of the important factors that affect seismic response such as inertial interaction, kinematic interaction, seismic pore water pressures, soil nonlinearity, cross stiffness coupling and dynamic pile to pile interaction. A nonlinear 3-D analysis is used to show how all these factors affect pile response, to demonstrate some of the consequences of using various approximate methods and to provide a comprehensive overview of how pile foundations behave during earthquakes in liquefiable and non-liquefiable soils.     

On the influence of the polarization and the shape of the strain loop on strain accumulation in sand under high-cyclic loading

This paper presents results of cyclic triaxial (CT) tests on sand with a simultaneous variation of the axial and the lateral stresses. Furthermore, a cyclic multidimensional simple shear (CMDSS) device and corresponding test results are discussed. For in-phase cycles with a constant strain amplitude it is demonstrated that the accumulation rate is independent of the polarization of the cycles in the strain space. Polarization changes lead to a temporary increase of the accumulation rate: they increase the effectiveness of compaction. For out-of-phase (e.g. elliptical) cycles the shape of the strain loop significantly influences the residual strain. A circular strain loop generates twice larger accumulation rates than a one-dimensional strain loop with identical span. The accumulation rate is not influenced by the circulation of the strain loop. It is shown that the direction of accumulation (so-called “cyclic flow rule”) is only moderately affected by the polarization and the shape of the cycles.     

Evaluation of state indices in predicting the cyclic and monotonic strength of sands with different fines contents

State parameter, ψ, has been widely used to combine the influence of void ratio, e, and stress level, p′, on the soils behavior. Stress ratio, R_s, and modified state parameter, ψ_m, have also been proposed for the same purpose. This paper aims to evaluate and compare the different state indices in combining the effect of fines content, density and stress level for five different types of sands, by processing a large number of previously published experimental data. The use of the recently established concept of equivalent interparticle void ratio, e^⁎, in definition of the state indices is also evaluated. The results indicate that the influence of fines presence, in addition to the e and p′, on the behavior is favorably reflected by the state indices. Unique correlations were derived between the cyclic or monotonic strength and each of the state indices, independent of the fines content. The correlations, for all the different types of soils, fell into limited types of common formulations. ψ and R_s worked generally better than ψ_m, whether defined in terms of e or e^⁎. The extension of straight part of critical state line was found to be an appropriate reference line for calculating R_s used in conjunction with e or e^⁎.     

A comparison of flow intensities in alluvial rivers: characteristics and implications for modelling flow processes

This paper compares flow intensity data obtained with different instruments from a variety of fluvial environments. It examines associations between the root-mean-square of longitudinal velocity fluctuations (flow intensity), local mean velocity, relative depth, and boundary resistance. Results indicate systematic differences in the behaviour of flow intensity which scale with respect to position in the boundary layer (deep sand-bedded rivers), boundary grain resistance (shallow river environments with coarse beds), and possibly form resistance (shallower sand-bedded rivers). Preliminary approaches to prediction and modelling of variations in flow intensity are suggested based upon linear regression relationships. Intensity values are also compared with theoretical and empirical limits to the use of Taylor's substitution, which allows time and frequency properties of a single-point velocity time series to be used to yield a flow length scale. In general, limits are exceeded in all environments for near-boundary flow measurements, but are met for y/d > 0·3 in most cases in sand-bed rivers, and for y/d > 0·4 in some gravel-bed environments. © 1998 John Wiley & Sons, Ltd.     

Characteristics of runoff and sediment yield for two typical erodible soils in southern China

Granite red soil (GRS) and Quaternary red clay (QRC) are two typical erodible soils in the red-soil region of southern China. Analytical and comparative studies of the characteristics of runoff and sediment yield for the two soils at various slopes are currently needed. The purpose of the current study was to clarify the characteristics of runoff and sediment yield for GRS and QRC at different slopes and to establish models for estimating sediment yield for the two soils. Forty-eight runoff microplots with four slopes (5°, 15°, 25°, and 35°) and two soils (GRS and QRC) were established and exposed to natural rainfall. Runoff and sediment yield were measured 10 times during the study period. Runoff and sediment yield for the two soils under the various slopes had similar temporal variations, and both increased with prior cumulative erosive rainfall. Runoff for GRS and QRC was moderately temporally variable, with coefficients of variation (CVs) from 46.2% to 60.6%, and sediment yield for QRC was strongly temporally variable, with CVs from 114.8% to 145.8%. Sediment yield for GRS increased with slope, but sediment yield for QRC first increased and then decreased, with a calculated inflection point of 18°, but runoff for both soils decreased with slope. The CVs of both runoff and sediment yield with slope for the two soils ranged from 3.6% to 88.0%, lower than the temporal variabilities, indicating that rainfall may have a larger impact than slope on runoff and sediment yield for QRC and GRS. Under the various slopes, runoff and sediment yield for both soils increased with rainfall and sediment yield increased with runoff, but the proportions of effective rainfall and runoff differed. Pedotransfer-function models based on rainfall, runoff, and slope accurately estimated sediment yield for the two soils, with the model fit coefficient of determination (R²) > 0.81 and the R² for verification >0.79. These results improve the understanding of the laws governing erosion for different soil types in the red-soil region of southern China and are important for managing the erosion of collapsing gullies and sloping farmland in the region.     

Spectral and petrologic analyses of basaltic sands in Ka'u Desert (Hawaii) – implications for the dark dunes on Mars

Dark aeolian deposits on Mars are thought to consist of volcanic materials due to their mineral assemblages, which are common to basalts. However, the sediment source is still debated. Basaltic dunes on Earth are promising analogs for providing further insights into the assumed basaltic sand dunes on Mars. In our study we characterize basaltic dunes from the Ka'u Desert in Hawaii using optical microscopes, electron microprobe, and spectral analyses. We compare the spectra of terrestrial and Martian dune sands to determine possible origins of the Martian dark sediments. Our results show that the terrestrial sands consist primarily of medium to coarse sand‐sized volcanic glass and rock fragments as well as olivine, pyroxene, and plagioclase minerals. Grain shapes range from angular to subrounded. The sample composition indicates that the material was derived from phreatomagmatic eruptions partially with additional proportions of rock fragments from local lava flows. Grain shape and size indicate the materials were transported by aeolian processes rather than by fluvial processes. Spectral analyses reveal an initial hydration of all terrestrial samples. A spectral mineralogical correlation between the terrestrial and Martian aeolian sands shows a similarity consistent with an origin from volcanic ash and lava. We suggest that the Martian deposits may contain similar abundances of volcanic glass, which has not yet been distinguished in Martian spectral data. Copyright © 2011 John Wiley & Sons, Ltd.     

A micromorphological record of contemporary and relict pedogenic processes in soils of the Indo‐Gangetic Plains: implications for mineral weathering,provenance and climatic changes

Micromorphology has important application in earth surface process and landform studies particularly in alluvial settings such as the Indo‐Gangetic Plains (IGP) with different geomorphic surfaces to identify climatic changes and neotectonic events and their influence on pedogenesis. The soils of the IGP extending from arid upland in the west to per humid deltaic plains in the east developed on five geomorphic surfaces namely QIG1 to QIG5 originating during the last 13.5 ka. Four soil‐geomorphic systems across the entire IGP are identified as: (i) the western Yamuna Plains/Uplands, (ii) the Yamuna‐Ganga Interfluve, (iii) the Ganga‐Ghaghara Interfluve, and (iv) the Deltaic Plains. Thin section analysis of the soils across the four soil‐geomorphic systems provides a record of provenance, mineral weathering, pedogenic processes and polygenesis in IGP. The soils over major parts of the IGP dominantly contain muscovite and quartz and small fraction of highly altered feldspar derived from the Himalayas. However, soils in the western and eastern parts of the IGP contain large volumes of fresh to weakly altered plagioclase and smectitic clay derived from the Indian craton. The soils in western Yamuna Plains/Uplands dominated by QIG2–QIG3 geomorphic surfaces and pedogenic carbonate developed in semi‐arid climate prior to 5 ka. However, soils of the central part of the IGP in the Yamuna‐Ganga Interfluve and Ganga‐Ghaghara Interfluve regions with dominance of QIG4–QIG5 surfaces are polygenetic due to climate change over the last 13.5 ka. The clay pedofeatures formed during earlier wet phase (13.5–11 ka) show degradation, loss of preferred orientation, speckled appearance in contrast with the later phase of wet climate (6.5–4 ka). The soils over the deltaic plains with dominance of vertic features along with clay pedofeatures suggest that illuviation of fine clay is an important pedogenic process even in soils with shrink‐swell characteristics. Copyright © 2015 John Wiley & Sons, Ltd.