Foehn signals detected by sodar wind and turbulence measurements in the Rhine Valley, Austria, during the MAP field phase

Summary Within the Mesoscale Alpine Programme MAP conducted in autumn 1999, the vertical structure and the temporal evolution of the planetary boundary layer (PBL) in the Rhine Valley 2km south of Lake Constance were observed with a Remtech PA2 sodar (sound-detection-and-ranging instrument) rendering half-hour averages of the three-dimensional wind profile within the lowest kilometre above ground. During Foehn events, tethered balloon soundings and wind profiler measurements were conducted in addition to the rawinsonde network which was built up for the MAP field campaign.The remote sensing instrument renders a surprisingly high number of valid data during south Foehn. Due to the frequent formation of a cold air pool with stable conditions below the Foehn flow with near-neutral static stability, even more sodar data is valid during Foehn periods than during no Foehn periods. A significant reduction of the sodar data quality is only observed during Foehn events with grounding of the Foehn at the sodar site due to high background noise. At higher levels, a Foehn signal can be detected from the sodar wind and turbulence intensitiy information. With Foehn, higher wind speeds and larger turbulence intensities occur than without Foehn. Comparisons to rawinsonde and tethersonde soundings and wind profiler measurements at sites nearby reveal the spatial inhomogeneity of the Foehn flow within this part of the valley as well as instrumental short-comings. Different methods to determine the mixing height using the vertical sounding devices lead to some uncertainty of mixing height estimates which however can reasonably be explained.     

Detection of Inversions and Mixing Height by REMTECH PA2 Sodar in Comparison with Collocated Radiosonde Measurements

Summary A REMTECH PA2 Doppler Sodar is operated regularly at the Czech Hydrometeorological Institute (CHMI) observatory in Prague, collocated with a routine rawinsonde sounding system. The Air Pollution Control Division of CHMI utilises the sodar data in air pollution studies and as an information support for the smog warning system operated in Prague. Besides of the basic software for echo strength and wind profile evaluation, optional routines for deriving parameters such as inversion and mixing height, stability class etc. were delivered by the sodar manufacturer. Based on a sufficiently large data set (more than one year) of synchronous sodar and rawinsonde measurements, an analysis and comparison of inversion and mixing heights provided by both sounding systems have been accomplished in order to evaluate the correctness and accuracy of sodar estimates of these parameters. In contrast to the wind speed and wind direction data, for which a satisfactory agreement with other kind of measurements has been reported by many studies, the results for inversion and mixing height detection were totally disappointing. A direct applicability of inversion height and mixing height data provided by the REMTECH’s automatic routines in air pollution studies or smog warning systems is quite problematical with the present “state of the art”. Received November 3, 1998 Revised April 20, 1999     

Mean wind speed profiles in the air basin of Moscow

Results of measurements of mean wind speed profiles and direction during two years in the center of the city of Moscow are presented. These measurements were performed with a Doppler acoustic profiler (sodar), which was used for continuous monitoring of the wind speed within the height range from 40 to 250–500 m. The averaged seasonal mean profiles are presented along with other observational data, including diurnal cycle parameters, wind speed and direction frequencies at chosen levels, and frequencies and duration of strong winds and calm weather.     

A one dimensional wind profile model with stability and eddy viscosity estimations from sodar data

In a one-dimensional wind profile model, methods for eddy viscosity and stability estimations from sodar data have been evaluated with soundings. For eddy viscosity parameterization the ageostrophic method and mixing-length theory have been investigated. Three methods for estimating the static stability have been evaluated; a wind profile adjustment method, gravity wave analysis of sodar backscatter and flux profile functions for windspeed and standard deviation of vertical wind-speed. The wind profile model with variable momentum flux (VF) with height shows better results than an earlier constant flux model (Bergström, 1986). The VF model can be used for extending the sodar profile up to 1500 m.     

Use of a High-Resolution Sodar to Study Surface-layer Turbulence at Night

Measurements in the atmospheric surface layer are generally made with point sensors located in the first few tens of metres. In most cases, however, these measurements are not representative of the whole surface layer. Standard Doppler sodars allow a continuous display of the turbulent thermal structure and wind profiles in the boundary layer up to 1000 m, with a few points, if any, in the surface layer. To overcome these limitations a new sodar configuration is proposed that allows for a higher resolution in the surface layer. Because of its capabilities (echo recording starting at 2 m, echo intensity vertical resolution of approximately 2 m, temporal resolution of 1 s) this sodar is called the surface-layer mini-sodar (SLM-sodar). Features and capabilities of the SLM-sodar are described and compared with the sodar. The comparison of the thermal vertical structure given by the SLM-sodar and the sodar provides evidence that, in most cases, the surface layer presents a level of complexity comparable to that of the entire boundary layer. Considering its high vertical resolution, the SLM-sodar is a promising system for the study of the nocturnal surface layer. The nocturnal SLM-sodar measurements have shown that, depending on wind speed, the structure of the surface layer may change substantially within a short time period. At night, when the wind speed is greater than 3 m s⁻¹, mechanical mixing destroys the wavy structure present in the nocturnal layer. Sonic anemometer measurements have shown that, in such cases, also the sensible heat flux varies with height, reaching a peak in correspondence with the wind speed peak. Under these conditions the assumption of horizontal homogeneity of the surface layer and the choice of the averaging time need to be carefully treated.     

Composite wind and temperature profiles obtained from a complex of in-situ and remote sensing measurement systems for the forcing of a boundary layer model

Summary ?This paper describes the configuration of measurement systems operated continuously at the Meteorological Observatory Lindenberg with the aim of constructing combined profiles of wind and temperature – so-called composite profiles – covering the boundary layer with high temporal and vertical resolution. This is required for the forcing of a micro-α-scale model in order to simulate the atmospheric boundary layer structure over a heterogeneous landscape during the LITFASS-98 experiment. The problems of combining measurements of different remote sensing and in-situ systems are briefly discussed. Although the measuring range of individual remote sensing systems is variable, the height coverage of wind and temperature profile measurements by sodar/RASS and two wind profiler radar/RASS complement each other very well. Using a simple merging procedure composite wind and temperature profiles have been synthesized based on radiosonde, windprofiler/RASS, sodar/RASS and tower measurements. Time-height cross sections of hourly composite profiles show considerably more details of the boundary layer structure than simple radiosonde interpolation due to the higher sampling frequency, higher vertical resolution and increased accuracy at the lower levels. Finally some qualifications of the formulated algorithm are suggested for future application. Received June 18, 2001; revised May 30, 2002; accepted June 6, 2002     

Wind regime in the lower atmosphere over Moscow from the long-term acoustic sounding data

Presented are the results of the sounding of the lower atmospheric 500-meter layer for the period of 2004–2012 carried out at the Meteorological Observatory of the Moscow State University (MSU) with the MODOS Doppler acoustic radar (sodar) produced by METEK (Germany). Discussed is the methodological basis of the sodar wind data analysis. It is demonstrated that in the air layer up to 200 m the maximum values in the annual course of the wind speed are observed more often in autumn and winter, and the minimum values, in summer; this is associated with the fact that during the cold period of the year Moscow is often located in the zones of intense gradient currents. The diurnal course of the wind speed is characterized by the daytime maximum and night-time minimum in the layer up to 40–60 m from the surface; it is poorly pronounced and characterized by the minimum in the morning in the layer of 80–120 m; and the daytime minimum and night-time maximum are observed above 140–160 m. The layer from 80 to 120 m approximately corresponds to the height of the wind rotation. The amplitude of diurnal variations of the wind speed increases from 0.3 m/s at the height of 7 m and 0.6 m/s at the height of 15 m, to 4.5 m/s at the height of 400 m; however, its secondary minimum (0.5 m/s) associated with the rotation height is registered at the altitude of 80 m. The statistical relationship between the wind speed and surface air temperature is direct during the cold season, inverse during the warm season, and is absent in April and October. The average maximum wind speed over Moscow for ten minutes in the layer up to 500 m from the surface reaches 30–35 m/s in some cases if two conditions concur: the capital is located on the periphery of vast pressure formations (usually of deep cyclones) and the local low-level jet stream is present in the wind profile.     

Comparison of wind measurements by means of industrially produced sodar and high-altitude meteorological mast in Obninsk

The real characteristics of the MFAS sodar industrially produced by Scintec AG (Germany) are given. The paper presents a wider range of altitudes as compared with the papers published before as a result of using the meteorological mast with the height of 310 m and longer duration of practically continuous testing embracing different weather conditions in the period from July to November 2008. During the comparison, the 10-min averaging time for the wind speed and direction is used. The comparison of the data of acoustic sounding and contact measurement methods indicates that the sodar provides reliable information on the vertical profiles of average wind speed within the considered altitude range up to 300 m except the cases of heavy rainfalls and low wind speed.     

Comparative analysis of sodar and ozone profile measurements in a complex structured boundary layer and implications for mixing height estimation

Profile data from simultaneous sodar and tethered balloon measurements have been analyzed with respect to the complex structure of the atmospheric boundary layer in the Upper Rhine Valley. Special attention was focused on ozone concentration profiles measured with a novel lightweight ozone sensor at the balloon. In general, good agreement was found between the signature of the ozone concentration profiles and special features of the backscattered sound intensity profiles. This allows reliable estimation of the mixing height from the sodar data even in a complex stable ABL, except for very shallow mixing layers (below about 75 m), which could not be detected by the sodar.     

Studies of the Marine Boundary Layer at Tarapur

Simultaneous observations were made of the Marine Boundary Layer at Tarapur, a site near Bombay on the sea coast, by acoustic sounder and instrumented tower. The meteorological tower was used to sense wind and temperature at various levels up to a height of 120 m while the acoustic sounder was used to examine the thermal structure of the boundary layer up to a height of 700 m. Data recorded for the year 1982 have been analysed.Analysis of the data shows that while the normal structures of thermal echoes and shear echoes represent the mixing depth of the atmospheric boundary layer, the often observed elevated layers are due to sea breeze reversals with their base giving a measure of the depth of the sea-breeze circulation during the day. A sea breeze has been detected during both spring (March to May) and autumn (October to December) months. The onset times are around 1000 hr during spring months and around noon during the autumn period, the height of development being respectively up to 500 and 350 m. The capability of the sodar to detect the base and thickness of the sea breeze, is clearly revealed.     

Observations of Atmospheric Solitary Waves in the Urban Boundary Layer

The simultaneous operation of a three-axis Doppler sodar system in the centralurban area of Rome and two similar systems in the suburban area, forming atriangle about 20 km on each side, provided evidence of solitary-type wavesin the urban boundary layer. Three events, each lasting from a few minutes toabout 30 min, and ranging in depth from the minimum range of the sodar (39 m) to over 500 m, are reported here. Two events were recognizable onall three sodar records while the third event could be observed at the urbanlocation only. Time-height acoustic echo intensity records showed no-echoregions within the wave indicating transport of trapped recirculating air.This is typical of large amplitude solitary waves. The time series plots ofsodar-derived vertical wind velocity revealed a maximum peak-to-peakvariation of about 5 m s^-1 during periods of wave-associated disturbance.The vertical velocity is found to increase with height up to the top of the closedcirculation within the wave and decreases further above. The normalisedamplitude-wavelength relationship for the two events indicates that theobserved waves are close to a strongly nonlinear regime.     

A COMPARISON BETWEEN THE DOPPLER SODAR AND IN-SITU WIND MEASUREMENTS

In this paper,a comparison is made of the Doppler sodar wind measurement with the in-situ measurements on a 325 m meteorological tower.The results show that when the ratio of signal to noise is larger than 1,the mean wind speeds and directions obtained from the two techniques are well correlated,thus their profiles are close to each other.The mean value and root mean square of vertical velocity measured by the Doppler sodar are a little larger than those measured by a sonic anemometer at a height of 85 m,which is in agreement with the analysis by Gaynor et al.(1983).We notice that there are some differences in the observational results between the Doppler sodar and insitu measurements,especially when comparing the values measured at each time.Therefore,it is important to analyze the reason for the differences and to make corrections to the Doppler sodar measurements.     

Wavy Vertical Motions in the ABL Observed by Sodar

Some characteristics of wavelike motions in the atmospheric boundary layer observed by sodar are considered. In an experiment carried out in February 1993 in Milan, Italy, Doppler sodar measurements were accompanied by in situ measurements of temperature and wind velocity vertical profiles using a tethered balloon up to 600 m. The oscillations of elevated wavy layers containing intense thermal turbulence, usually associated with temperature-inversion zones, were studied by using correlation and spectral analysis methods. The statistics of the occurrence of wavelike and temperature-inversion events are presented. The height distributions of Brunt–Vaisala frequency and wind shear and their correlation within elevated inversion layers were determined, with a strong correlation observed between the drift rate of the wavy layers and the vertical velocity measured by Doppler sodar inside these layers. Spectral analysis showed similarities regarding their frequency characteristics. The phase speed and propagation direction of waves were estimated from the time delay of the signals at three antennae to provide estimates of wavelength. Moreover, wavelengths were estimated from the intrinsic frequency obtained from sodar measurements of the Doppler vertical velocity and oscillations of wavy turbulent layers. The two wavelength estimates are in good agreement.     

Corrections for Wind-Speed Errors from Sodar and Lidar in Complex Terrain

The quality of lidar and sodar wind estimates is generally judged through comparisons with mast-mounted instruments, and the resulting regressions. Evaluation of the relative merits of lidars versus sodars is complicated by the fact that lidars are generally placed close to a mast whereas sodars are generally placed some distance from a mast so that acoustic reflections off the mast are reduced. This leads to the two technologies, lidar and sodar, not being compared in similar situations. Differences arising from the two geometries can be expected to be larger in complex terrain, where the wind regime can vary significantly spatially. The current work explores these differences in moderately complex terrain. Lidar–mast comparisons are performed with the lidar close to an 80 m mast, and sodar–mast comparisons performed with the sodar 300 m from the mast. Systematic variations in estimated wind speed are found to occur with height, consistent with predictions from a simple flow model. When the lidar was moved to the sodar location, further from the mast, there were significant changes in the estimated wind speeds and a reduction in correlation with the mast-based wind speeds, as expected. However, the correlation between collocated lidar and sodar winds was high. This finding emphasizes that any comparison of two remote sensing instruments needs to be through similar experiments, and that differences in accuracy often reported for the lidar and sodar technologies are likely to be contaminated due to poor comparison configurations. A method was devised to simulate the sodar being collocated with the mast, by using the lidar–sodar measurements and the lidar–mast measurements. It was found that there was then no statistically detectable difference between lidar–mast regressions and sodar–mast regressions for the particular lidar and sodar tested. Both remote sensing instruments were also found to be good estimators of Weibull parameters, as compared with those derived from mast data. The conclusion is that the sodar measured the winds above the sodar with a similar accuracy to the lidar measuring winds above the lidar.     

Studies of sodar‐observed dot echo structures

Abstract

During moist weather under stably stratified and light wind conditions very often “dot” shaped echoes, either distributed randomly or arranged in a stratified layer, have been observed on sodar echograms. They last from a couple of hours to ten hours. Their horizontal widths are up to 200 m while their vertical sizes are up to 40 m. It is argued that dot echoes represent clusters of water vapour translated by the wind in the boundary layer, the back‐scattered acoustic energy being the contribution of correlated fluctuations in temperature and humidity (turbulent mixing) in the inertial subrange.     

基于风廓线雷达的广东登陆台风边界层高度特征研究

针对8个登陆广东省的热带气旋,利用经过数据质量控制的风廓线雷达连续、高时空分辨率的风场观测数据,对热带气旋边界层特征进行了分析。研究结果表明:热带气旋边界层中切向风速大值区垂直范围越大、风速越强、持续时间越久,则热带气旋强度越大、登陆后强度维持时间越久。眼区外入流层厚度越大,入流层气流越强,热带气旋登陆后强度维持时间则越久。风廓线雷达信噪比垂直梯度对大气湍流信息有一定的指示作用,对于入流层高度在2000 m以下的热带气旋,其入流层顶所在高度与信噪比梯度最大值所在高度相近,对于入流层较为深厚的热带气旋,用信噪比垂直梯度确定的边界层高度虽接近入流层顶高,但仍有一定差距。不同特点的热带气旋其边界层高度并不相同,对于登陆后强度迅速减弱的热带气旋边界层高度在500~1000 m;登陆后强度持续时间短的热带气旋,其边界层高度约1000~2000 m;登陆后强度持续时间长的热带气旋,其边界层高度在2000 m之上,最高可达5000~7000 m。这些结果加深了对登陆台风边界层高度演变特征的认识。     

The UHF wind profiler at Vienna airport – data quality control and comparisons to rawinsonde data

Summary A 1290MHz wind profiler (Radian Lap-3000), at present one of three operational wind profilers in Austria, is operated at Vienna airport. In spite of quality assurance procedures as consensus averaging included in the data evaluation process from profiler raw data, some spurious peaks of wind speed and unrealistic changes of the wind vector in time or height occur in the wind measurements. This is especially true for sampling intervals of only 5 minutes which are used to resolve the temporal evolution of summer thunderstorms and frontal passages. Averaging periods of only a few minutes are rather the lower limit apt for wind profiler observations and result in a low data availability of 28%, whereas about 55% of data (relative to the maximum height range according to the parameter setting) are available for 10 to 30 minutes profiles.Approaches to a posteriori quality control using checks for automatic error detection are proposed and tested on a one and a half year data-set: Flagging data when the three-dimensional wind divergence exceeds a predefined limit (0.5s^–1) is in most cases successful in combination with thresholds for wind speed (2 times the median of the daily data-set) or wind shear (0.2s^–1).The wind profiler data is compared to wind profiles from the next radiosonde station where soundings are launched 4 times a day at Hohe Warte, approx. 20km northwest, at the hill-side of the Viennese Woods. Deviations of about 1m s^–1 in wind speed are found between the observations of the two systems. Differences between the wind profiles within the boundary layer can be explained by local differences in the wind regime observed at the airport and the radiosounding – blocking effects of the Viennese Woods during south-easterly flow. Comparing the profiler data to radiosoundings on a monthly basis gives a tool to monitor the profiler performance.     

Application of the 915 MHz profiler for diagnosing and classifying tropical precipitating cloud systems

Summary The NOAA Aeronomy Laboratory has developed a 915 MHz lower tropospheric wind profiler designed primarily for measuring wind in the planetary boundary layer of the tropics. In recent years the profiler has been used in many field programs worldwide. The profiler is being deployed by the Aeronomy Laboratory at several locations in the tropics to provide long-term measurements for the Tropical Ocean Global Atmosphere (TOGA) program and the Global Ocean Atmosphere Land Surface (GOALS) program. In the absence of precipitating cloud systems the profiler observes winds routinely up to altitudes of 3 to 6 km in the tropics depending primarily on humidity. In the presence of precipitating cloud systems, however, the profiler height coverage is substantially increased due to the presence of hydrometeors to which the profiler is sensitive at its wavelength of 33 cm. In this paper we examine the application of the 915 MHz profiler to the diagnosis and classification of precipitating cloud systems in the tropics. Preliminary results from Christmas Island confirm that at least half of tropical rainfall is stratiform in nature being associated with mesoscale convective systems. The 915 MHz profiler provides a means for the development of a climatology of tropical precipitating cloud systems. Such a climatology is needed to specify diabatic heating rates in large-scale numerical weather prediction and climate models. It should also help develop improved rain retrieval algorithms from satellite observations.With 10 Figures     

The wind speed shear in the case of stable stratification and the scales of the similarity theory

The wind speed shear in the case of stable stratification in the linear part of the profile spreading high above the surface layer of constant flows is studied using the data of long-term sodar measurements in the atmospheric boundary layer. The wind speed shear in this part remains almost invariable during several hours at the significant change in parameters of the Monin-Obukhov theory. The length of this linear part can be associated with the layer of the critical Richardson number. In the case of the pronounced temperature inversion (with the positive gradient of more than 1°C per 100 m), the wind speed profile is close to the linear function in the most part of the nocturnal mixing layer. Proposed is a scale characterizing the height of the surface layer of constant flows.     

近山地区大气边界层声雷达回波的季节特征

本文根据北京附近某一近山地区冬季和夏季的声雷达探测结果,对比了大气边界层声雷达回波图象在季节上的相似性和差异,分析了冬夏逆温层和对流混合层的生消演变特征,并对声雷达回波图象的几种类型与边界层风廓线的关系作了初步探讨。