Anisotropy and depth‐related heterogeneity of hydraulic conductivity in a bog peat. II: modelling the effects on groundwater flow

Anisotropy and heterogeneity of hydraulic conductivity (K) are seldom considered in models of mire hydrology. We investigated the effect of anisotropy and heterogeneity on groundwater flow in bog peat using a steady‐state groundwater model. In five model simulations, four sets of K data were used. The first set comprised measured K values from an anisotropic and heterogeneous bog peat. These data were aggregated to produce the following simplified data sets: an isotropic and heterogeneous distribution of K; an isotropic and homogeneous distribution; and an anisotropic and homogeneous distribution. We demonstrate that, where anisotropy and heterogeneity exist, groundwater flow in bog peat is complex. Fine‐scale variations in K have the potential to influence patterns and rates of groundwater flow. However, for our data at least, it is heterogeneity and not anisotropy that has the greater influence on producing complex patterns of groundwater flow. We also demonstrate that patterns and rates of groundwater flow are simplified and reduced when measured K values are aggregated to create a more uniform distribution of K. For example, when measured K values are aggregated to produce isotropy and homogeneity, the rate of modelled seepage is reduced by 28%. We also show that when measured K values are used, the presence of a drainage ditch can increase seepage through a modelled cross‐section. Our work has implications for the accurate interpretation of hydraulic head data obtained from peat soils, and also the understanding of the effect of drainage ditches on patterns and rates of groundwater flow. Copyright © 2002 John Wiley & Sons, Ltd.     

Numerical simulation of groundwater flow patterns using flux as upper boundary

Since the 1960s, most of the studies on groundwater flow systems by analytical and numerical modelling have been based on given‐head upper boundaries. The disadvantage of the given‐head approach is that the recharge into and discharge from a basin vary with changes in hydraulic conductivity and/or basin geometry. Consequently, flow patterns simulated with given‐head boundaries but with different hydraulic conductivities and/or basin geometry may not reflect the effects of these variables. We conducted, therefore, numerical simulations of groundwater flow in theoretical drainage basins using flux as the upper boundary and realistically positioned fluid‐potential sinks while changing the infiltration intensity, hydraulic conductivities, and geometric configuration of the basin. The simulated results demonstrate that these variables are dominant factors controlling the flow pattern in a laterally closed drainage basin. The ratio of infiltration intensity to hydraulic conductivity (R_ic) has been shown to be an integrated pattern‐parameter in a basin with a given geometric configuration and possible fluid‐potential‐sink distribution. Successively, the changes in flow patterns induced by stepwise reductions in R_ic are identical, regardless of whether the reductions are due to a decrease in infiltration intensity or an increase in hydraulic conductivity. The calculated examples show five sequential flow patterns containing (i) only local, (ii) local–intermediate, (iii) local–intermediate–regional, (iv) local–regional, and (v) just regional flow systems. The R_ic was found to determine also whether a particular sink is active or not as a site of discharge. Flux upper boundary is preferable for numerical simulation when discussing the flow patterns affected by a change of infiltration, the hydraulic conductivity, or the geometry of a basin. Copyright © 2012 John Wiley & Sons, Ltd.     

Modelling two‐dimensional steady‐state groundwater flow and flow sensitivity to boundary conditions in blanket peat complexes

This study used a two‐dimensional steady‐state finite‐element groundwater flow model to simulate groundwater flow in two Newfoundland blanket peat complexes and to examine flow system sensitivity to changes in water table recharge and aquifer properties. The modelling results were examined within the context of peat‐forming processes in the two complexes. Modelled flow compared favourably with observed flow. The sensitivity analyses suggested that more highly decomposed bog peat along bog margins probably has/had a positive impact on net peat accumulation within bog interiors. Peat with lower hydraulic conductivity along bog margins effectively impedes lateral drainage, localizes water table drawdown to extreme bog margins, and elevates water tables along bog interiors. Peat formation and elevated water tables in adjacent poor fens/laggs currently rely on placic and ortstein horizons impeding vertical drainage and water flow inputs from adjacent bogs. Modest reductions in atmospheric recharge were found to govern bog‐flow‐system geometries in a way that would adversely affect paludification processes in adjacent fens/laggs. Copyright © 2004 John Wiley & Sons, Ltd.     

Direct observation of complex Tóthian groundwater flow systems in the laboratory

Based on the theory of gravity‐driven groundwater flow systems, we have developed a complex Flow System Sand‐Box Model (FSM). It enables the visual observations of the development and characteristics and temporal evolution of complex Tóthian flow systems in the laboratory. The configuration of the regional, intermediate and local flow systems can be controlled and observed; hydraulic head, flow direction and travel time can be measured; and the scale and shape of the sub‐flow systems as well as the path lines and flow lines can be observed directly. The experiments demonstrate the Tóthian flow systems in a small basin with multiple sources and sinks. Greater local topographic (water table) undulation will lead to larger local flow systems. Greater regional and less local topographic undulation will enhance the development of intermediate and regional flow systems. In homogeneous media, increasing fluid‐potential differences between source and sink increase the spatial scale of the generated flow systems. The FSM is a useful teaching aid and experimental device to study and develop an intuitive insight into gravity‐driven groundwater flow systems. It helps to visualize and understand the hydraulic properties and controlling factors of Tóthian flow systems and may be used to study problems related to the chemical and temperature characteristics of the flow systems as well. Copyright © 2010 John Wiley & Sons, Ltd.     

Reducing monitoring gaps at the aquifer–river interface by modelling groundwater–surface water exchange flow patterns

This study investigates spatial patterns and temporal dynamics of aquifer–river exchange flow at a reach of the River Leith, UK. Observations of sub‐channel vertical hydraulic gradients at the field site indicate the dominance of groundwater up‐welling into the river and the absence of groundwater recharge from surface water. However, observed hydraulic heads do not provide information on potential surface water infiltration into the top 0–15 cm of the streambed as these depths are not covered by the existing experimental infrastructure. In order to evaluate whether surface water infiltration is likely to occur outside the ‘window of detection’, i.e. the shallow streambed, a numerical groundwater model is used to simulate hydrological exchanges between the aquifer and the river. Transient simulations of the successfully validated model (Nash and Sutcliff efficiency of 0·91) suggest that surface water infiltration is marginal and that the possibility of significant volumes of surface water infiltrating into non‐monitored shallow streambed sediments can be excluded for the simulation period. Furthermore, the simulation results show that with increasing head differences between river and aquifer towards the end of the simulation period, the impact of streambed topography and hydraulic conductivity on spatial patterns of exchange flow rates decreases. A set of peak flow scenarios with altered groundwater‐surface water head gradients is simulated in order to quantify the potential for surface water infiltration during characteristic winter flow conditions following the observation period. The results indicate that, particularly at the beginning of peak flow conditions, head gradients are likely to cause substantial increase in surface water infiltration into the streambed. The study highlights the potential for the improvement of process understanding of hyporheic exchange flow patterns at the stream reach scale by simulating aquifer‐river exchange fluxes with a standard numerical groundwater model and a simple but robust model structure and parameterization. Copyright © 2011 John Wiley & Sons, Ltd.     

Influence of pore size and geometry on peat unsaturated hydraulic conductivity computed from 3D computed tomography image analysis

In organic soils, hydraulic conductivity is related to the degree of decomposition and soil compression, which reduce the effective pore diameter and consequently restrict water flow. This study investigates how the size distribution and geometry of air‐filled pores control the unsaturated hydraulic conductivity of peat soils using high‐resolution (45 µm) three‐dimensional (3D) X‐ray computed tomography (CT) and digital image processing of four peat sub‐samples from varying depths under a constant soil water pressure head. Pore structure and configuration in peat were found to be irregular, with volume and cross‐sectional area showing fractal behaviour that suggests pores having smaller values of the fractal dimension in deeper, more decomposed peat, have higher tortuosity and lower connectivity, which influences hydraulic conductivity. The image analysis showed that the large reduction of unsaturated hydraulic conductivity with depth is essentially controlled by air‐filled pore hydraulic radius, tortuosity, air‐filled pore density and the fractal dimension due to degree of decomposition and compression of the organic matter. The comparisons between unsaturated hydraulic conductivity computed from the air‐filled pore size and geometric distribution showed satisfactory agreement with direct measurements using the permeameter method. This understanding is important in characterizing peat properties and its heterogeneity for monitoring the progress of complex flow processes at the field scale in peatlands. Copyright © 2010 John Wiley & Sons, Ltd.     

Contribution of climatic and anthropogenic effects to the hydric deficit of peatlands

The present study makes use of a detailed water balance to investigate the hydrological status of a peatland with a basal clay‐rich layer overlying an aquifer exploited for drinking water. The aim is to determine the influence of climate and groundwater extraction on the water balance and water levels in the peatland. During the two‐year period of monitoring, the hydrological functioning of the wetland showed a hydric deficit, associated with a permanent unsaturated layer and a deep water table. At the same time, a stream was observed serving as a recharge inflow instead of draining the peatland, as usually described in natural systems. Such conditions are not favourable for peat accumulation. Field investigations show that the clay layer has a high hydraulic conductivity (from 1·10^?7 to 3·10^?9 m.s^?1) and does not form a hydraulic barrier. Moreover, the vertical hydraulic gradients are downward between the peat and the sand aquifer, leading to high flows of groundwater through the clay layer (20–48% of the precipitation). The observed hydric deficit of the peatland results from a combination of dry climatic conditions during the study period and groundwater extraction. The climatic effect is mainly expressed through drying out of the peatland, while the anthropogenic effect leads to an enhancement of the climatic effect on a global scale, and a modification of fluxes at a local scale. The drying out of the peatland can lead to its mineralisation, which thus gives rise to environmental impacts. The protection of such wetlands in the context of climate change should take account of anthropogenic pressures by considering the wetland‐aquifer interaction. Copyright © 2011 John Wiley & Sons, Ltd.     

FLOW REVERSALS IN PEATLANDS INFLUENCED BY LOCAL GROUNDWATER SYSTEMS

Piezometric head data from various depths were examined at two peatlands in Ontario, Canada and one peatland in Sweden influenced by small-scale, shallow groundwater systems. Data from different hydrogeological settings show reversals in groundwater flow leading to discharge in topographically high regions of peatlands in isolation from large-scale groundwater flow. It is suggested that subsurface flow within peat can reverse in direction in response to water deficit and water-table drawdown. The data presented here refute the assumption that local groundwater flow in peatlands is unidirectional and further illustrate the fact that measurable subsurface water flow can occur at depth in peat isolated from large-scale groundwater flow systems. In the light of implicit assumptions made by many workers on water movement in peatlands, especially when connected to small-scale groundwater systems, the consequences of such reversals are paramount in understanding the hydrology and biogeochemistry of peatlands. © 1997 by John Wiley & Sons, Ltd.     

An analytical study on three‐dimensional versus two‐dimensional water table‐induced flow patterns in a Tóthian basin

Although it has been increasingly acknowledged that groundwater flow pattern is complicated in the three‐dimensional (3‐D) domain, two‐dimensional (2‐D) water table‐induced flow models are still widely used to delineate basin‐scale groundwater circulation. However, the validity of 2‐D cross‐sectional flow field induced by water table has been seldom examined. Here, we derive the analytical solution of 3‐D water table‐induced hydraulic head in a Tóthian basin and then examine the validity of 2‐D cross‐sectional models by comparing the flow fields of selected cross sections calculated by the 2‐D cross‐sectional model with those by the 3‐D model, which represents the “true” cases. For cross sections in the recharge or discharge area of the 3‐D basin, even if head difference is not significant, the 2‐D cross‐sectional models result in flow patterns absolutely different from the true ones. For the cross section following the principal direction of groundwater flow, although 2‐D cross‐sectional models would overestimate the penetrating depth of local flow systems and underestimate the recharge/discharge flux, the flow pattern from the cross‐sectional model is similar to the true one and could be close enough to the true one by adjusting the decay exponent and anisotropy ratio of permeability. Consequently, to determine whether a 2‐D cross‐sectional model is applicable, a comparison of hydraulic head difference between 2‐D and 3‐D solutions is not enough. Instead, the similarity of flow pattern should be considered to determine whether a cross‐sectional model is applicable. This study improves understanding of groundwater flow induced by more natural water table undulations in the 3‐D domain and the limitations of 2‐D models accounting for cross‐sectional water table undulation only.     

Modelling study on the impact of deep building foundations on the groundwater system

Coastal areas are usually the preferred place of habitation for human beings. Anthropogenic activities such as the construction of high‐rise buildings and underground transport systems usually require extensive deep foundations and ground engineering works, which may unintentionally modify the coastal groundwater system because the construction materials of foundations are usually of low hydraulic conductivity. In this paper, the impact of these building foundations on the groundwater regime is studied using hypothetical flow and transport models. Various possible realizations of foundation distributions are generated using stochastic parameters derived from a topographical map of an actual coastal area in Hong Kong. The effective hydraulic conductivity is first calculated for different realizations and the results show that the effective hydraulic conductivity can be reduced significantly. Then a hypothetical numerical model based on FEFLOW is set up to study the change of hydraulic head, groundwater discharge, and saltwater‐fresh water interface. The groundwater level and flow are modified to various degrees, depending on the foundations percentage and the distribution pattern of the buildings. When the foundations percentage is high and the building foundations are aggregated, the hydraulic head is raised significantly and the originally one‐dimensional groundwater flow field becomes complicated. Seaward groundwater discharge will be reduced and some groundwater may become seepage through the ground surface. The transport model shows that, after foundations are added, overall the seawater and fresh groundwater interface moves landward, so extensive foundations may induce seawater intrusion. It is believed that the modification of the coastal groundwater system by building foundations may have engineering and environmental implications, such as submarine groundwater discharge, foundation corrosion, and slope stability. Copyright © 2007 John Wiley & Sons, Ltd.     

Scale‐dependency of hydraulic conductivity: an example from Thorne Moor,a raised mire in South Yorkshire,UK

The hydraulic conductivity (K) of many low permeability materials is strongly scale‐dependent. In raised mires and other types of peat deposit the effects of features such as abandoned infilled ditches, root holes and localized woody material, cause K to be heterogeneous and scale‐dependent. Despite this, field measurements are routinely made using auger hole (slug) tests at the scale of only a few tens of centimetres. Such measurements are locally valid, but where the regional subsurface movement of water through peat bogs is simulated using groundwater models, typically at the scale of hundreds of metres, they give rise to a systematic underestimate of flows and an overprediction of water table elevations. Until now, techniques to obtain values at a scale sufficiently large to include the effects of localized features of higher permeability have not been applied routinely. Research at Thorne Moor, a large raised mire, demonstrates that the K of peat varies over several orders of magnitude when measured at different scales, using a variety of techniques. Laboratory and auger hole tests cannot be relied upon to provide results that represent the hydraulic conductivity of large expanses of peatland. This has significant implications for the management and long‐term restoration of peatlands where both regional and local control of water levels is crucial. For groundwater models to be used successfully to plan such schemes, it is essential to apply the K values relevant to the scale of the simulation. This paper describes and tests novel techniques, using ditches, for the derivation of K at large scales which overcome many of the problems that have been identified with conventional techniques and are capable of producing estimates that are appropriate to the application of physically based regional flow models. Copyright © 2004 John Wiley & Sons, Ltd.     

Characteristics of preferential flow and groundwater discharge to Shingobee Lake,Minnesota, USA

Small‐scale heterogeneities and large changes in hydraulic gradient over short distances can create preferential groundwater flow paths that discharge to lakes. A 170 m² grid within an area of springs and seeps along the shore of Shingobee Lake, Minnesota, was intensively instrumented to characterize groundwater‐lake interaction within underlying organic‐rich soil and sandy glacial sediments. Seepage meters in the lake and piezometer nests, installed at depths of 0·5 and 1·0 m below the ground surface and lakebed, were used to estimate groundwater flow. Statistical analysis of hydraulic conductivity estimated from slug tests indicated a range from 21 to 4·8 × 10^?3 m day^?1 and small spatial correlation. Although hydraulic gradients are overall upward and toward the lake, surface water that flows onto an area about 2 m onshore results in downward flow and localized recharge. Most flow occurred within 3 m of the shore through more permeable pathways. Seepage meter and Darcy law estimates of groundwater discharge agreed well within error limits. In the small area examined, discharge decreases irregularly with distance into the lake, indicating that sediment heterogeneity plays an important role in the distribution of groundwater discharge. Temperature gradients showed some relationship to discharge, but neither temperature profiles nor specific electrical conductance could provide a more convenient method to map groundwater–lake interaction. These results suggest that site‐specific data may be needed to evaluate local water budget and to protect the water quality and quantity of discharge‐dominated lakes. Copyright © 2002 John Wiley & Sons, Ltd.     

The impact of pipe flow in riparian peat deposits on nitrate transport and removal

The effect of preferential flow in soil pipes on nitrate retention in riparian zones is poorly understood. The characteristics of soil pipes and their influence on patterns of groundwater transport and nitrate dynamics were studied along four transects in a 1‐ to >3‐m deep layer of peat and marl overlying an oxic sand aquifer in a riparian zone in southern Ontario, Canada. The peat‐marl deposit, which consisted of several horizontal layers with large differences in bulk density, contained soil pipes that were generally 0.1 to 0.2 m in diameter and often extended vertically for 1 to >2 m. Springs that produced overland flow across the riparian area occurred at some sites where pipes extended to the peat surface. Concentrations of NO₃^?–N (20–30 mg L^?1) and dissolved oxygen (DO) (4–6 mg L^?1) observed in peat pipe systems and surface springs were similar to values in the underlying sand aquifer, indicating that preferential flow transported groundwater with limited nitrate depletion. Low NO₃^?–N concentrations of <5 mg L^?1 and enriched δ¹⁵N values indicated that denitrification was restricted to small areas of the peat where pipes were absent. Groundwater DO concentrations declined rapidly to <2 mg L^?1 in the peat matrix adjacent to pipes, whereas high NO₃^?–N concentrations of >15 mg L^?1 extended over a larger zone. Low dissolved organic carbon values at these locations suggest that supplies of organic carbon were not sufficient to support high rates of denitrification, despite low DO conditions. These data indicate that it is important to develop a greater understanding of pipes in peat deposits, which function as sites where the transport of large fluxes of water with low biogeochemical reaction rates can limit the nitrate removal capacity of riparian zones. Copyright © 2011 John Wiley & Sons, Ltd.     

Analytical studies on transient groundwater flow induced by land reclamation using different fill materials

Land reclamation may have a significant influence on groundwater regimes. Analytical solutions have been developed in the past to study the impact of land reclamation on a steady‐state groundwater flow and transient flow in fill materials, assuming that the reclamation site consists of a single zone of uniform hydraulic parameters. In this paper, we derive analytical solutions to describe the transient water table change in response to multi‐stage land reclamation where the fill material is uniform in each stage but the hydraulic conductivity of the fill material varies from stage to stage. By introducing the method of separation of variables, we develop a transient analytical solution to study the impact of land reclamation consisting of fill material with different hydraulic properties on groundwater dynamics. The results show that the water table first increases significantly into the reclaimed zone following the fill material deposition, and then the increase gradually propagates into the original aquifer. The change of water table in the original aquifer mainly depends on the value of hydraulic conductivity of the fill materials. Examples in this paper illustrate how the aquifer system experiences a long time unsteady‐state flow as a result of the reclamation, and it takes at least tens of years for the system to approach a new equilibrium. It is suggested that for a large‐scale reclamation project, the response of the groundwater regime to reclamation should be carefully studied. Copyright © 2013 John Wiley & Sons, Ltd.     

Effective groundwater–surface water exchange at watershed scales

Coupled groundwater–surface water (GW–SW) models are capable of simulating complex hydrological systems when used at fine resolutions. However, properly characterizing bulk GW–SW fluxes for either coarsely resolved integrated models or basin‐discretized surface water models remains a challenge. Loss of subgrid detail, while beneficially decreasing computational cost, leads to a decrease in model accuracy as scale effects become important. Ideally, coarse low‐resolution models should be informed by expected subgrid behaviour, reducing the impact of scale effects. Determining how to best represent these fine‐scale details in lower‐resolution models is important for improving the accuracy and appropriateness of these models. To investigate some of these scale effects, we here explore the relationships between area‐averaged hydraulic head and bulk GW–SW exchange fluxes (e.g. evapotranspiration and discharge), all of which are presumed to be controlled predominantly by subgrid topographic effects. These relationships may be useful for simply upscaling models without the complete loss of crucial fine‐resolution subgrid details. Using finely resolved simulation output from Modflow for a fine‐resolution simulation and post‐processed results generated to represent coarser resolutions, upscaled flux relationships (UFRs) are generated for multiple terrains; these UFRs define the relationships that exist between average hydraulic head and average fluxes in unconfined aquifer systems. It is found that, for steady‐flow regimes, similar one‐to‐one power law relationships consistently exist between area‐averaged hydraulic heads, exchange fluxes and saturated area for a variety of terrains. Additionally, when the averaged values are properly normalized, the generated steady‐state UFRs for a single terrain are independent of hydraulic conductivity and potential evapotranspiration rates and apparently insensitive to the presence of mild heterogeneity. While some hysteresis is apparent in the relationships under transient conditions, transient artefacts are shown to be minor under some circumstances, indicating that UFRs may be applied to both steady‐state and transient scenarios. Simpler tests performed under saturated and variably saturated conditions in a cross‐sectional model show similar trends, suggesting that the UFR representation is extendable to systems where the vadose zone plays a significant role. It is suggested that relatively simple UFRs such as these may find use as an alternative to direct point upscaling or multi‐resolution models for estimating GW–SW exchange fluxes in coarse‐scale models. They also appear to justify the functional form of some classical models of baseflow and evapotranspiration used in conceptual surface water models. Copyright © 2015 John Wiley & Sons, Ltd.     

Defining hydrochemical evolution of streamflow through flowpath dynamics in Kawakami headwater catchment,Central Japan

The hydrochemical behaviour of catchments is often investigated by inferring stream chemistry through identification of source areas involved in hydrograph separation analysis, yet its dynamic evolution of hydrologic pathways has received little attention. Intensive hydrometric and hydrochemical measurements were performed during two different storms on March 29, 2001 and August 21–22, 2001 to define hydrochemical evolution under the dynamic of flow pathways in a 5·2 ha first‐order drainage of the Kawakami experimental basin (KEB), Central Japan, a forested headwater catchment with various soil depths (1·8 to 5 m) overlying late Neogene of volcanic bedrocks. The hydraulic potential distribution and flow lines data showed that the change in flow direction, which was controlled by rainfall amount and antecedent wetness of the soil profile, agreed well with the hydrochemical change across the slope segment during the storm. Hydrograph separation predicted by end‐member mixing analysis (EMMA) using Ca²⁺ and SiO₂ showed that near surface riparian, hillslope soil water and deep riparian groundwater were important in stream flow generation. The evidence of decrease in solutes concentration at a depth of 1 m in the hillslope and 0·6 m in the near surface riparian during peak storm suggested a flushing of high solutes concentration. Most of the solutes accumulated in the deep riparian groundwater zone, which was due to prominent downward flow and agreed well with the residence time. The distinct flow pathways and chemistry between the near surface riparian and deep riparian groundwater zones and the linkage hillslope aquifer and near surface riparian reservoir, which controls rapid flow and solutes flushing during the storm event, are in conflict with the typical assumption that the whole riparian zone resets flow pathways and chemical signature of hillslope soil water, as has been reported in a previous study. Copyright © 2005 John Wiley & Sons, Ltd.     

An experimental study of water table recharge by seepage losses from a ditch with intermittent flow

Farmed catchments in the Mediterranean area often exhibit dense networks of ditches which are also preferential zones of water table recharge, and thereby of groundwater contamination. This study presents an experimental analysis of seepage losses and related groundwater recharge patterns during a typical Mediterranean runoff event at the scale of a ditch located above a shallow water table. The objectives were (i) to evaluate the patterns of water table recharge by seepage in a ditch, (ii) to study the main flow processes occurring during recharge, and (iii) to estimate solute propagation in case of contaminated flow in the ditch. The field observation indicated three major points. Firstly, they showed that seepage losses during a runoff event in a ditch can rapidly lead to a significant recharge of a shallow water table. Secondly, the recharge induces a groundwater mound much larger than the event plume. The infiltrated water and the accompanying solutes remained in the vicinity of the ditch. The patterns of groundwater recharge and contamination appeared very different. Lastly, both unsaturated and saturated‐piston flow processes were observed which suggests that a variably‐saturated flow modelling approach ought to be used to simulate the ditch‐water shallow table interaction. Finally, the study indicates that the patterns of water table recharge and contamination in Mediterranean catchments with dense ditches network vary largely in space and time, and will require dense monitoring networks to estimate the evolution of the average contamination levels. Copyright © 2008 John Wiley & Sons, Ltd.     

Divergence and flow direction as indicators of subsurface heterogeneity and stage‐dependent storage in alluvial floodplains

Assuming homogeneity in alluvial aquifers is convenient, but limits our ability to accurately predict stream‐aquifer interactions. Research is needed on (i) identifying the presence of focused, as opposed to diffuse, groundwater discharge/recharge to streams and (ii) the magnitude and role of large‐scale bank and transient storage in alluvial floodplains relative to changes in stream stage. The objective of this research was to document and quantify the effect of stage‐dependent aquifer heterogeneity and bank storage relative to changes in stream stage using groundwater flow divergence and direction. Monitoring was performed in alluvial floodplains adjacent to the Barren Fork Creek and Honey Creek in northeastern Oklahoma. Based on results from subsurface electrical resistivity mapping, observation wells were installed in high and low electrical resistivity subsoils. Water levels in the wells were recorded real time using pressure transducers (August to October 2009). Divergence was used to quantify heterogeneity (i.e. variation in hydraulic conductivity, porosity, and/or aquifer thickness), and flow direction was used to assess the potential for large‐scale (100 m) bank or transient storage. Areas of localized heterogeneity appeared to act as divergence zones allowing stream water to quickly enter the groundwater system, or as flow convergence zones draining a large groundwater area. Maximum divergence or convergence occurred with maximum rates of change in flow rates or stream stage. Flow directions in the groundwater changed considerably between base and high flows, suggesting that the floodplains acted as large‐scale bank storage zones, rapidly storing and releasing water during passage of a storm hydrograph. During storm events at both sites, the average groundwater direction changed by at least 90° from the average groundwater direction during baseflow. Aquifer heterogeneity in floodplains yields hyporheic flows that are more responsive and spatially and temporally complex than would be expected compared to more common assumptions of homogeneity. Copyright © 2012 John Wiley & Sons, Ltd.     

Stage‐dependent transient storage of phosphorus in alluvial floodplains

Models for contaminant transport in streams commonly idealize transient storage as a well mixed but immobile system. These transient storage models capture rapid (near‐stream) hyporheic storage and transport, but do not account for large‐scale, stage‐dependent interaction with the alluvial aquifer. The objective of this research was to document transient storage of phosphorus (P) in coarse gravel alluvium potentially influenced by large‐scale, stage‐dependent preferential flow pathways (PFPs). Long‐term monitoring was performed at floodplain sites adjacent to the Barren Fork Creek and Honey Creek in northeastern Oklahoma. Based on results from subsurface electrical resistivity mapping which was correlated to hydraulic conductivity data, observation wells were installed both in higher hydraulic conductivity and lower hydraulic conductivity subsoils. Water levels in the wells were monitored over time, and water samples were obtained from the observation wells and the stream to document P concentrations at multiple times during high flow events. Contour plots indicating direction of flow were developed using water table elevation data. Contour plots of total P concentrations showed the alluvial aquifer acting as a transient storage zone, with P‐laden stream water heterogeneously entering the aquifer during the passage of a storm pulse, and subsequently re‐entering the stream during baseflow conditions. Some groundwater in the alluvial floodplains had total P concentrations that mirrored the streams' total P concentrations. A detailed analysis of P forms indicated that particulate P (i.e. P attached to particulates greater than 0·45 µm) was a significant portion of the P transport. This research suggests the need for more controlled studies on stage‐dependent transient storage in alluvial systems. Copyright © 2011 John Wiley & Sons, Ltd.     

A high‐altitude temporary spring in a compartmentalized carbonate aquifer: the role of low‐permeability faults and karst conduits

The aim of this research was to refine the actual conceptual model related to the activation of high‐altitude temporary springs within the carbonate Apennines in southern Italy. The research was carried out through geophysical, hydrogeological, hydrochemical and isotopic investigations at the Acqua dei Faggi experimental site during five hydrologic years. The research demonstrated that, in carbonate aquifers where low‐permeability faults cause the aquifer system to be compartmentalized, high‐altitude temporary springs may be recharged by groundwater. In such settings, neither surface water infiltration in karst systems nor perched temporary aquifers play a role of utmost importance. The rare (once or a few time a year) activation of such springs is due to the fact that groundwater unusually reach the threshold head that allows the spring to flow. The activation of the studied high‐altitude temporary spring also depended on relationships between a low‐permeability fault core and a karst system that locally interrupts the low‐permeability barrier. In fact, when the hydraulic head did not reach the karst system, the concentrated head loss within the fault core did not allow the spring to flow, because the groundwater entirely flowed through the fault towards the downgradient compartment. Copyright © 2009 John Wiley & Sons, Ltd.