Bioaugmentation in a Well‐Characterized Fractured Rock DNAPL Source Area

A field demonstration was performed at Edwards Air Force Base to assess bioaugmentation for treatment of a well‐characterized tetrachloroethene (PCE) dense nonaqueous phase liquid (DNAPL) source area in fractured rock. Groundwater recirculation was employed to deliver remedial amendments, including bacteria, to facilitate reductive dechlorination and enhance DNAPL dissolution. An active treatment period of 9 months was followed by a 10‐month posttreatment rebound evaluation. Dechlorination daughter products were observed in both the shallow and deep fracture zones following treatment. In the shallow fracture zone, the calculated DNAPL mass removed was approximately equal to the DNAPL mass estimated using partitioning tracer testing, and no rebound in chlorinated ethenes or ethene was observed during the posttreatment period. A maximum DNAPL dissolution enhancement factor of 5 was observed in the shallow fracture zone. In the deep fracture zone, only approximately 45% of the DNAPL mass—as estimated via partitioning tracer testing—was removed and rebound in the total molar chlorinated ethenes + ethene was observed. The difference in behavior between the shallow and deep fracture zones was attributed to DNAPL architecture and the fracture flow field.     

Pesticides Removal Using Conventional and Low‐Cost Adsorbents: A Review

Worldwide pesticide usage has increased dramatically during the last three decades, coinciding with changing practices and increasing by intensive agriculture. This widespread use of pesticides for agricultural and non‐agricultural purposes has resulted in the presence of their residues in various environmental matrices. The occurrence of pesticides and their metabolite transported in rivers, channels, lakes, sea, air, soils, groundwater, and even drinking water, proves the high risk of these chemicals to human health and the environment. Therefore, pesticide removal is of an increasing concern. In this study, a review of the published literature dealing with pesticides removal process is presented. Firstly, pesticide removal by conventional means is briefly considered. Secondly, the use of the low‐cost sorbent through biosorption process is discussed comprehensively. The effect of factors such as pH, contact time, sorbent dosage, initial pesticide concentration, and optimization of biosorption conditions is also discussed. Kinetic, thermodynamic, and mechanism studies are also given. This study shows that both microorganisms and other materials with biological origin like agricultural by‐products may be used to this end. There is a significant potential for pesticide uptake by the use of various pristine and especially modified biosorbents. In the case of living organisms used as removal agents, degradation may also play a role in the total removal observed.     

Removal of Organic Pollutants from Wastewater Using Wood Fly Ash as a Low‐Cost Sorbent

In this study, untreated and treated wood fly ash (WA) was used as a low‐cost sorbent in batch sorption tests to investigate the removal of organic pollutants from a real wastewater generated by cleaning/washing of machinery in a wood‐laminate floor industry in Sweden. The experiments focused on the effect of the WA dosage and particle size on the removal efficiency for organic compounds. With a WA dosage of 160 g L^?1 and a particle size less than 1 mm, the reductions of chemical oxygen demand (COD), biologic oxygen demand, and total organic carbon were 37 ± 0.4, 24 ± 0.4, and 30 ± 0.3%, respectively. Pre‐treatment of WA with hot water improved the COD removal efficiency by absorption from 37 ± 0.4 to 42 ± 1.6% when the same dosage (160 g L^?1) was applied. Sorption isotherm and sorption kinetics for COD using untreated WA can be explained by Freundlich isotherm and pseudo‐second‐order kinetic models. Intra‐particle diffusion model indicates that pore diffusion is not the rate‐limiting step for COD removal. Based on the experimental data, WA could be used as an alternative low‐cost sorption media/filter for removal of organic compounds from real industrial wastewater.     

Evaluation of a Novel Control Method on Biofilm Parameters in an Aerated Submerged Fixed‐bed Biofilm Reactor

One of the critical technological parameter in operation of aerated submerged fixed‐bed biofilm reactor (ASFBBR) is the control over process of biofilm detachment. Both, an excessive growth of biomass with its accumulation in the bioreactor and an exceeded biofilm detachment rate, cause serious operational and technological problems. The studies presented in this paper demonstrate that in an ASFBBR reactor with a PVC bed carrier media, an effective way to maintain a proper shear stress acting on the biofilm and causing its detachment could be an internal recirculation of wastewater instead of backwashing with wastewater or air flushing. In case of polishing of oil‐refinery wastewater with average COD loading rate equal to 9 g COD/(m² day), the minimum value of the hydraulic loading rate in such reactor is 1.9 m³/(m² h), at which there was no excessive growth of biofilms. Despite a significant decrease of the biofilms thickness and amount of biomass in the reactor, there was no significant decline in the efficiency of pollutant removal from oil‐refinery wastewater, which made it possible to obtain the quality of effluent at the outlet of the bioreactor significantly below the water permits and standards.     

Field Test of Enhanced Remedial Amendment Delivery Using a Shear‐Thinning Fluid

Heterogeneity of hydraulic properties in aquifers may lead to contaminants residing in lower‐permeability zones where it is difficult to deliver remediation amendments using conventional injection processes. The focus of this study is to examine use of a shear‐thinning fluid (STF) to improve the uniformity of remedial amendment distribution within a heterogeneous aquifer. Previous studies have demonstrated the significant potential of STFs for improving remedial amendment delivery in heterogeneous aquifers, but quantitative evaluation of these improvements from field applications is lacking. A field‐scale test was conducted that compares data from successive injection of a tracer in water followed by injection of a tracer in an STF to evaluate the impact of the STF on tracer distribution uniformity in the presence of permeability contrasts within the targeted injection zone. Data from tracer breakthrough at multiple depth‐discrete monitoring intervals and electrical resistivity tomography (ERT) showed that inclusion of STF in the injection solution improved the distribution of the injected fluid within the targeted treatment zone. One improvement was a reduction in the movement of injected fluids through high‐permeability pathways, as evidenced by slower breakthrough of tracer at monitoring locations where breakthrough in baseline tracer‐only injection data was faster. In addition, STF‐amended injection solutions arrived faster and to a greater extent in monitoring locations within low‐permeability zones. ERT data showed that the STF injection covered a higher percentage of a two‐dimensional cross section within the injection interval between the injection well and a monitoring well about 3 m away.     

Characterization and Source History Modeling Using Low‐k Zone Profiles at Two Source Areas

Like tree rings, high‐resolution soil sampling of low‐permeability (low‐k) zones can be used to evaluate the style of source history at contaminated sites (i.e., historical pattern of concentration and composition vs. time since releases occurred at the interface with the low‐k zone). This is valuable for the development of conceptual site model (CSM) and can serve as an important line of evidence supporting monitored natural attenuation (MNA) as a long‐term remedy. Source histories were successfully reconstructed at two sites at Naval Air Station Jacksonville using a simple one‐dimensional (1D) model. The plume arrival time and historical composition were reconstructed from the time initial releases that were suspected to occur decades earlier. At the first site (Building 106), the source reconstructions showed relatively constant source concentrations, but significant attenuation over time in the downgradient plume in the transmissive zone, suggesting MNA may not be an appropriate remedy if source control is a requirement, but attenuation processes are clearly helping to maintain plume stability and reduce risk. At the second site (Building 780), source concentrations in the transmissive zone showed an approximately a one order of magnitude over time, but apparently less attenuation in the downgradient plume. The source reconstruction method appeared to reflect site remediation efforts (excavation, soil vapor extraction) implemented in the 1990s. Finally, a detailed analysis using molecular biological tools, carbon isotopes, and by‐products suggests that most degradation activity is associated with high‐k zones but not with low‐k zones at these source areas. Overall, the source reconstruction methodology provided insight into historical concentration trends not obtainable otherwise given the limited long‐term monitoring data.     

Field Test of a Hybrid Finite‐Difference and Analytic Element Regional Model

Regional finite‐difference models often have cell sizes that are too large to sufficiently model well‐stream interactions. Here, a steady‐state hybrid model is applied whereby the upper layer or layers of a coarse MODFLOW model are replaced by the analytic element model GFLOW, which represents surface waters and wells as line and point sinks. The two models are coupled by transferring cell‐by‐cell leakage obtained from the original MODFLOW model to the bottom of the GFLOW model. A real‐world test of the hybrid model approach is applied on a subdomain of an existing model of the Lake Michigan Basin. The original (coarse) MODFLOW model consists of six layers, the top four of which are aggregated into GFLOW as a single layer, while the bottom two layers remain part of MODFLOW in the hybrid model. The hybrid model and a refined “benchmark” MODFLOW model simulate similar baseflows. The hybrid and benchmark models also simulate similar baseflow reductions due to nearby pumping when the well is located within the layers represented by GFLOW. However, the benchmark model requires refinement of the model grid in the local area of interest, while the hybrid approach uses a gridless top layer and is thus unaffected by grid discretization errors. The hybrid approach is well suited to facilitate cost‐effective retrofitting of existing coarse grid MODFLOW models commonly used for regional studies because it leverages the strengths of both finite‐difference and analytic element methods for predictions in mildly heterogeneous systems that can be simulated with steady‐state conditions.     

Low‐frequency wave propagation in periodically layered media

In this paper, we consider wave propagation in a layered medium. Using the Baker‐Campbell‐Hausdorff series, we expand the logarithm of a propagator matrix in series of frequency. The series coefficients allow us to extend the effective Backus medium for low frequencies. The proposed technique is applied to vertical propagation in a periodically layered and binary medium as well as for a gradient medium. The velocity dispersion equations are derived for these media. We also consider the layered medium with monoclinic anisotropy. We illustrate the accuracy of the proposed method on synthetic and well‐log data.     

Arsenic Remediation Field Study Using a Sulfate Reduction and Zero‐Valent Iron PRB

Toxic and carcinogenic effects of arsenic in drinking water continue to impact people throughout the world and arsenic remains common in groundwater at cleanup sites and in areas with natural sources. Advances in groundwater remediation are needed to attain the low concentrations that are protective of human health and the environment. In this article, we present the successful use of a permeable reactive barrier (PRB) utilizing sulfate reduction coupled with zero‐valent iron (ZVI) to remediate the leading edge of a dissolved arsenic plume in a wetland area near Tacoma, Washington. A commercially available product (EHC‐M®, Adventus Americas Inc., Freeport, Illinois) that contains ZVI, organic carbon substrate, and sulfate was injected into a reducing, low‐seepage‐velocity aquifer elevated in dissolved arsenic and iron from a nearby, slag‐containing landfill. Removal effectiveness was strongly correlated with sulfate concentration, and was coincident with temporary redox potential (Eh) reductions, consistent with arsenic removal by iron sulfide precipitation. The PRB demonstrates that induced sulfate reduction and ZVI are capable of attaining a regulatory limit of 5 µg/L total arsenic, capturing of 97% of the arsenic entering the PRB, and sustaining decreased arsenic concentrations for approximately 2 years, suggesting that the technology is appropriate for consideration at other sites with similar hydrogeochemical conditions. The results indicate the importance of delivery and longevity of minimum sulfate concentrations and of maintaining sufficient dissolved organic carbon and/or microscale ZVI to precipitate FeS, a precursor phase to arsenic‐bearing pyrite that may provide a stable, long‐term sink for arsenic.     

Effects of Linking a Soil‐Water‐Balance Model with a Groundwater‐Flow Model

A previously published regional groundwater‐flow model in north‐central Nebraska was sequentially linked with the recently developed soil‐water‐balance (SWB) model to analyze effects to groundwater‐flow model parameters and calibration results. The linked models provided a more detailed spatial and temporal distribution of simulated recharge based on hydrologic processes, improvement of simulated groundwater‐level changes and base flows at specific sites in agricultural areas, and a physically based assessment of the relative magnitude of recharge for grassland, nonirrigated cropland, and irrigated cropland areas. Root‐mean‐squared (RMS) differences between the simulated and estimated or measured target values for the previously published model and linked models were relatively similar and did not improve for all types of calibration targets. However, without any adjustment to the SWB‐generated recharge, the RMS difference between simulated and estimated base‐flow target values for the groundwater‐flow model was slightly smaller than for the previously published model, possibly indicating that the volume of recharge simulated by the SWB code was closer to actual hydrogeologic conditions than the previously published model provided. Groundwater‐level and base‐flow hydrographs showed that temporal patterns of simulated groundwater levels and base flows were more accurate for the linked models than for the previously published model at several sites, particularly in agricultural areas.     

Tide‐Induced Air Pressure Fluctuations in a Coastal Unsaturated Zone: Effects of Thin Low‐Permeability Pavements

This paper presents an analytical case study to explore one‐dimensional subsurface air pressure variation in a coastal three‐layered unsaturated zone. The upper layer is thin and much less permeable than the middle layer, and water table is located in the very permeable lower layer. An analytical solution was derived to describe the air pressure variation caused by tide‐induced water table fluctuations. We revisited the case study at Hong Kong International Airport conducted by Jiao and Li (2004) who used a two‐dimensional numerical model. The analytical prediction using the parameter values equivalent to the two‐dimensional numerical model agreed very well with the observed air pressure, indicating the validity and applicability of our one‐dimensional model in approximating the actual situation in this coastal zone with adequate accuracy. The analysis revealed that the asphalt pavement played an important role in causing air pressure fluctuations below it. Abnormally high air pressure can be caused beneath the surface pavement when the air permeability decreases due to rainfall infiltration, which may lead to heaving problems during rising tides.     

Membrane Interface Probe Protocol for Contaminants in Low‐Permeability Zones

Accurate characterization of contaminant mass in zones of low hydraulic conductivity (low k) is essential for site management because this difficult‐to‐treat mass can be a long‐term secondary source. This study developed a protocol for the membrane interface probe (MIP) as a low‐cost, rapid data‐acquisition tool for qualitatively evaluating the location and relative distribution of mass in low‐k zones. MIP operating parameters were varied systematically at high and low concentration locations at a contaminated site to evaluate the impact of the parameters on data quality relative to a detailed adjacent profile of soil concentrations. Evaluation of the relative location of maximum concentrations and the shape of the MIP vs. soil profiles led to a standard operating procedure (SOP) for the MIP to delineate contamination in low‐k zones. This includes recommendations for: (1) preferred detector (ECD for low concentration zones, PID or ECD for higher concentration zones); (2) combining downlogged and uplogged data to reduce carryover; and (3) higher carrier gas flow rate in high concentration zones. Linear regression indicated scatter in all MIP‐to‐soil comparisons, including R² values using the SOP of 0.32 in the low concentration boring and 0.49 in the high concentration boring. In contrast, a control dataset with soil‐to‐soil correlations from borings 1‐m apart exhibited an R² of ≥0.88, highlighting the uncertainty in predicting soil concentrations using MIP data. This study demonstrates that the MIP provides lower‐precision contaminant distribution and heterogeneity data compared to more intensive high‐resolution characterization methods. This is consistent with its use as a complementary screening tool.     

Field Treatment of MTBE‐Contaminated Groundwater Using Ozone/UV Oxidation

Methyl‐tertiary butyl ether (MTBE) is often found in groundwater as a result of gasoline spills and leaking underground storage tanks. An extrapolation of occurrence data in 2008 estimated at least one detection of MTBE in approximately 165 small and large public water systems serving 896,000 people nationally (United States Environmental Protection Agency [U.S. EPA] 2008). The objective of this collaborative field study was to evaluate a small groundwater treatment system to determine the effectiveness of ultraviolet (UV)/ozone treatment in removing MTBE from contaminated drinking water wells. A pilot‐scale advanced oxidation process (AOP) system was tested to evaluate the oxidation efficiency of MTBE and intermediates under field conditions. This system used ozone as an oxidizer in the presence of UV light at hydraulic retention times varying from 1 to 3 min. MTBE removal efficiencies approaching 97% were possible with this system, even with low retention times. The intermediate t‐butyl alcohol (TBA) was removed to a lesser extent (71%) under the same test conditions. The main intermediate formed in the oxidation process of the contaminated groundwater in these studies was acetone. The concentrations of the other anticipated intermediates t‐butyl formate (TBF), isopropyl alcohol (IPA), methyl acetate (MAc), and possible co‐occurring aromatics (BTEX) in the effluent were negligible.     

Low‐Resolution Modeling of Dense Drainage Networks in Confining Layers

Groundwater‐surface water (GW‐SW) interaction in numerical groundwater flow models is generally simulated using a Cauchy boundary condition, which relates the flow between the surface water and the groundwater to the product of the head difference between the node and the surface water level, and a coefficient, often referred to as the “conductance.” Previous studies have shown that in models with a low grid resolution, the resistance to GW‐SW interaction below the surface water bed should often be accounted for in the parameterization of the conductance, in addition to the resistance across the surface water bed. Three conductance expressions that take this resistance into account were investigated: two that were presented by Mehl and Hill (2010) and the one that was presented by De Lange (1999). Their accuracy in low‐resolution models regarding salt and water fluxes to a dense drainage network in a confined aquifer system was determined. For a wide range of hydrogeological conditions, the influence of (1) variable groundwater density; (2) vertical grid discretization; and (3) simulation of both ditches and tile drains in a single model cell was investigated. The results indicate that the conductance expression of De Lange (1999) should be used in similar hydrogeological conditions as considered in this paper, as it is better taking into account the resistance to flow below the surface water bed. For the cases that were considered, the influence of variable groundwater density and vertical grid discretization on the accuracy of the conductance expression of De Lange (1999) is small.     

Low‐temperature thermochronological database of bedrock in the Japanese Islands

To provide better access to thermochronological data and understand the long‐term denudation history of the Japanese Islands, we compiled a low‐temperature thermochronological dataset of fission‐track (FT) and (U–Th–Sm)/He (He) ages for apatite and zircon in bedrocks. These thermochronometric ages are compiled from 90 literature sources and 1,096 localities, and include 418 apatite FT ages, 851 zircon FT ages, 42 apatite He ages, and 30 zircon He ages. Many FT ages have been reported previously; however, the number of He ages is limited in the Japanese Islands. The compiled data are spatially biased; for instance, more data are reported for the Chubu and Kinki districts and the Pacific coast of the Shikoku Island, whereas less data were available for the Tohoku and Chugoku districts. For better understanding arc‐scale uplift‐denudation history, further thermochronological research in the lesser‐studied regions and more He thermochronometric measurements are desired. This compilation will be updated and provided on the website of the Fission‐Track Research Group in Japan ( http://ftrgj.org/index.html ).     

H2S Emissions from a Submerged Pilot‐Scale Fixed Bed Biofilm Reactor

A study was performed in two submerged, pilot‐scale biofilm bioreactors operated under different conditions to determine the relationship between the operating parameters and H₂S emission. H₂S was always detected in the exhaust air at concentrations varying from 1 to 353 ppm_v. The specific aeration rate was the most influencing parameter, with As < 30 kg COD (dissolved oxygen concentrations <4 mg L^?1) increasing noticeably the H₂S production. The periodical removal of the accumulated sludge reduced H₂S emissions by ～14%.