Prediction of acid mine drainage generation potential in selected mines in the Ashanti Metallogenic Belt using static geochemical methods

Acid mine/rock drainage (AMD/ARD) is the biggest environmental threat facing the mining industry. This study investigates AMD/ARD possibilities in three mines in the Ashanti Belt, using acid base accounting (ABA) and net acid generation pH (NAGpH) tests. Twenty-eight samples of rock units and mine spoil from these mines were collected for ABA and NAGpH tests. Two tailing dumps at Prestea and Nsuta were confirmed by both methods as acid generating with NAGpH of 4.5 and 4.6 and neutralization potential ratio values of 4.38 and 4.60, respectively. Six other samples are classified as potentially acid generating using a variety of established classification criteria. The rest of the samples either exhibited very low sulphur and carbonate content or had excess carbonate over sulphur. Consistency between results from ABA and NAGpH tests validates these tests as adequate tools for preliminary evaluation of AMD/ARD possibilities in any mining project in the Ashanti Belt.     

Mineralogical constraints on the determination of neutralization potential and prediction of acid mine drainage

 Acid-base accounting tests, commonly used as a screening tool in acid mine drainage (AMD) predictions, have limitations in (1) measuring with confidence the amount of neutralizers present in samples and (2) affording an interpretation of what the test results mean in terms of predicting the occurrence of acid mine drainage. Aside from the analytical difficulties inherent to the conventional methods, a potential source of error in neutralization potential (NP) measurements is the contribution from the dissolution of non-carbonate minerals. Non-carbonate alkalinity measured during static tests may or may not be available to neutralize acidity produced in the field. In order to assess the value-added of extending the NP with the knowledge of mineralogical composition and evaluate potential sources of errors in NP measurements, a suite of samples were examined and characterized in terms of their mineralogical and chemical compositions. The results indicate that although the acid-base accounting tests work well for simple compositions, the tests may result in overestimation or underestimation of NP values for field samples. Mineralogical constraint diagrams relating NP determinations to Ca, Mg and CO₂ concentrations were developed with the purpose to serve as supplementary guides to conventional static tests in identifying possible NP contributions from non-carbonate minerals and checking the quality of the chemical testing results. Mineralogical NP makes it possible to interpret the meaning of NP results and to assess the behaviour of samples over time by predicting the onset of AMD and calculating NP values for individual size fractions. Received: 1 June 1998 · Accepted: 6 October 1998     

The status of the passive treatment systems for acid mine drainage in South Korea

This study was performed to investigate the operating status, evaluate the problems, and discuss possible improvement methods of passive treatment systems for acid mine drainage (AMD) in South Korea. Thirty-five passive treatment systems in 29 mines have been constructed from 1996 to 2002 using successive alkalinity producing systems (SAPS) as the main treatment process. We investigated 29 systems (two for metal mines), 19 of which revealed various problems. Overflows of drainage from SAPS, wetland, or oxidation ponds were caused by the flow rate exceeding the capacities of the facilities or by the reduced permeability of the organic substance layer. Leakages occurred at various parts of the systems. In some cases, clogged and broken pipes at the mouths of the mine adits made the whole system unusable. Some systems showed very low efficiencies without apparent leakage or overflow. Even though the systems showed fairly good efficiencies in metal removal ratios (mainly iron) and pH control; sulfate removal rates were very poor except in three systems, which may indicate very poor sulfate reductions with sulfate reducing bacteria (SRB) as a means.     

Modelling natural attenuation of heavy-metal groundwater contamination in the Selebi-Phikwe mining area,Botswana

Seepage from a tailings dam is the major source of groundwater pollution in the Selebi-Phikwe area, where mining of sulphidic nickel–copper–cobalt ore started in 1973 and will continue until 2014. The seepage water has a pH in the range of 1.7–2.8 and is strongly enriched in SO₄ ²⁻ (5,680 g/L) and heavy metals (6,230 μg/L Ni, 1,860 μg/L Cu and 410 μg/L Co). The fracture aquifer affected by pollution from the dam exhibits a remarkable capacity of heavy-metal sorption. Most of the Ni, Cu and Co is scavenged at less than 500 m distance downgradient from the polluting source, whereas SO₄ ²⁻ is not immobilized significantly. The heavy-metal sorption process is assumed to be due to surface complexation, which is supported by a relatively high groundwater pH (in the range of 6.2–7.8 at >200 m distance from the tailings dam). The objective of this study is to demonstrate that the sorption process can be incorporated into a realistic three-dimensional reactive-transport groundwater model that is implicitly charge-balanced. The simulations are performed with the PHAST1.2 program, which is based on the HST3D flow and transport code and the hydrochemical PHREEQC2.12 code.     

Heavy metal pollution and acid drainage from the abandoned Balya Pb-Zn sulfide Mine,NW Anatolia,Turkey

This study was conducted to determine the effects of the waste-rock dump (WRD) of the underground polymetallic Balya Mine on the Kocacay River and eventually on Lake Manyas in Turkey. Data presented in this paper include geochemical characteristics of various kinds of water (mine, surface and groundwater) and of suspended-particle samples in the vicinity of Balya. The more polluted mine waters have low pH and high conductivity, while high concentrations of Zn, Cd, Mn tend to be found in the dry and wet seasons. High concentrations of Pb, As, Cr, Cu and S appear only in the wet season. The sources of the heavy metal concentration within the Kocacay River are leached waste, surface run off, and overflow from the spillway of the WRD. To minimize the formation of acids and dissolved metal, and for the remediation of the harmful effects of extreme contamination conditions, it is recommended that lime or alkali materials and organic carbon be added to simulate the action of sulfate-reducing bacteria.     

Interaction of acid mine drainage with waters and sediments at the Corona stream, Lousal mine (Iberian Pyrite Belt, Southern Portugal)

This study investigates the geochemical characteristics of the acid mine drainage discharged from the abandoned mine adits and tailing piles in the vicinity of the Lousal mine and evaluates the extent of pollution on water and on the stream sediments of the Corona stream. Atmospheric precipitation interacting with sulphide minerals in exposed tailings produces runoff water with pH values as low as 1.9–2.9 and high concentrations of (9,249–20,700 mg l⁻¹), Fe (959–4,830 mg l⁻¹) and Al (136–624 mg l⁻¹). The acidic effluents and mixed stream water carry elevated Cu, Pb, Zn, Cd and As concentrations that exceed the water quality standards. However, the severity of contamination generally decreases 4 km downstream of the source due to mixing with fresh waters, which causes the dilution of dissolved toxic metals and neutralization of acidity. Some natural attenuation of the contaminants also occurs due to the general reduced solubility of most trace metals, which may be removed from solution, by either co-precipitation or adsorption to the iron and aluminium precipitates.     

A laboratory study of covers made of low-sulphide tailings to prevent acid mine drainage

Covers with capillary barrier effects (CCBE) are considered to be one of the most effective ways to control acid mine drainage (AMD) production from mine wastes. The use of low-sulphide tailings in CCBE has been proposed recently for cases where other types of material may be unavailable near the mining site. This paper presents leaching column test results showing that CCBEs with a moisture-retaining layer made of slightly reactive tailings, with three different sulphide contents, can effectively limit the production of AMD from the acid-generating tailings placed underneath. With these layered covers, the leachate pH was maintained near neutrality throughout the testing period. When compared to uncovered tailings, the efficiency of the cover systems for reducing the amount of contaminants in the percolated water was determined to be greater than 99% for zinc, copper and iron. This study shows that the use of low-sulphide tailings can improve the ability of a CCBE to limit gas diffusion by consuming a fraction of the migrating oxygen.     

Geochemical distribution and removal of As,Fe, Mn and Al in a surface water system affected by acid mine drainage at a coalfield in Southwestern China

The chemical characteristics, formation and natural attenuation of pollutants in the coal acid mine drainage (AMD) at Xingren coalfield, Southwest China, are discussed in this paper based on the results of a geochemical investigation as well as geological and hydrogeological background information. The chemical composition of the AMD is controlled by the dissolution of sulfide minerals in the coal seam, the initial composition of the groundwater and the water–rock interaction. The AMD is characterized by high sulfate concentrations, high levels of dissolved metals (Fe, Al, Mn, etc.) and low pH values. Ca²⁺ and SO₄ ²⁻ are the dominant cation and anion in the AMD, respectively, while Ca²⁺ and HCO₃ ⁻ are present at significant levels in background water and surface water after the drainage leaves the mine site. The pH and alkalinity increase asymptotically with the distance along the flow path, while concentrations of sulfate, ferrous iron, aluminum and manganese are typically controlled by the deposition of secondary minerals. Low concentrations of As and other pollutants in the surface waters of the Xingren coalfield could be due to relatively low quantities being released from coal seams, to adsorption and coprecipitation on secondary minerals in stream sediments, and to dilution by unpolluted surface recharge. Although As is not the most serious water quality problem in the Xingren region at present, it is still a potential environmental problem. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Measured and computed neutralization potentials from static tests of diverse rock types

Static tests typically are used in the initial stage of environmental assessments to predict the potential for acid mine drainage, and also are used to monitor waste disposal at active mining operations. The neutralization potential (NP) of 19 sedimentary, metamorphic, and igneous extrusive rocks was measured by the Sobek method to compare the results with those computed by using the quantitative mineralogy of the rocks and the NP values that were deemed to be appropriate for the individual minerals. Most of the computed NP values of the rocks are lower than the measured values, but a close relationship is evident. If the contents of carbonate minerals are low, the NP in non-ultramafic igneous rocks typically is controlled by the amount of Ca substitution in plagioclase, whereas in ultramafic rocks the NP contribution is dominated by the amount of olivine and serpentine. Compositional and NP analyses of plagioclase concentrates indicate that the NP systematically varies from <1 for the Na end-member to about 14 for compositions near that of the Ca end-member. Among several variables that can affect the Sobek NP values, the volume and normality of the acid added to the sample are well-known to influence the results; however, the temperature and duration of the acidification stage can also have a pronounced effect on the measured NP of some rocks, depending on their mineralogy. Fizz tests to estimate the carbonate content and the consequent acid addition are highly subjective, and the ‘no fizz’ rating is not to be taken literally. The NP results themselves provide a clear indication of whether a sample has been over-acidified or under-acidified in the test procedure.     

The potential formation of acid mine drainage in pyrite-bearing hard-coal tailings under water-saturated conditions: an experimental approach

 Annually, an amount of approximately 13 million cubic meters of hard-coal tailings must be disposed of in the German Ruhr Valley. Besides the waste of land in a densily populated region, the disposal of the pyrite-bearing material under atmospheric conditions may lead to the formation of acid mine drainage (AMD). Therefore, alternative disposal opportunities are of increasing importance, one of which being the use of tailings under water-saturated conditions, such as in backfilling of abandoned gravel pits or in the construction of waterways. In this case, the oxidation of pyrite, and hence the formation of AMD, is controlled by the amount of oxygen dissolved in the pore water of tailings deposited under water. In case the advective percolation of water is suppressed by sufficient compaction of the tailings, oxygen transport can be reduced to diffusive processes, which are limited by the diffusive flux of dissolved oxygen in equilibrium with the atmospheric pO₂. Calculations of the duration of pyrite oxidation based on laboratory experiments have shown that the reduction of oxygen is mainly controlled by the content of organic substance rather than the pyrite content, a fact that is supported by results from oxidation experiments with nitrate. A "worst case" study has lead to the result that the complete oxidation of a 1.5-m layer of hard-coal tailings deposited under water-saturated conditions would take as much as several hundred thousand years. Received: 6 May 1996 · Accepted: 2 August 1996     

Geochemical Processes Controlling the Formation of As-Rich Waters Within a Tailings Impoundment (Carnoulès, France)

The distribution of arsenic (As(III), As(V)) and iron (Fe(II), Fe(III)) species was monitored during 1 year in a borehole drilled in the Carnoulès tailings impoundment which contains As-rich pyrite. The concentrations of total As and Fe in subsurface waters exhibited strong variations over one year, which were controlled by dissolved oxygen concentrations. At high oxygen levels, extremely high As (up to 162 mM) and Fe (up to 364 mM) concentrations were reached in the borehole, with the oxidised species predominant. As and Fe concentrations decreased 10-fold under oxygen-deficient conditions, as a result of pH increase and subsequent precipitation of As(V) and Fe(III). From drill core sections, it appeared that at low dissolved oxygen levels, As(III) was primarily released into water by the oxidation of As-rich pyrite in the unsaturated zone. Subsequent As and Fe precipitation was promoted during transport to the saturated zone; this reaction resulted in As enrichments in the sediment below the water table compared to the original content in pyrite, together with the formation of As-rich (up to 35 wt% As) ferruginous material in the unsaturated zone. High amounts of As(V) were released from these secondary phases during leaching experiments with oxygenated acid sulfate-rich waters; this process is believed to contribute to As(V) enrichment in the subsurface waters of the Carnoulès tailings during periods of high dissolved oxygen level.     

金川铜镍矿山尾矿砂酸溶性实验研究

为研究金川铜镍矿山酸性废水溶解尾矿砂实现综合治理废液与废固的可能性,进行了尾矿砂在硫酸中的溶解实验。结果表明,尾矿砂在硫酸浓度大于3mol/L、温度保持90℃以上并在液固比6.0下强力搅拌,能够较好地溶解于硫酸中,生成无定形二氧化硅;300℃的马弗炉焙烧4h有助于尾矿砂中绿泥石的溶解,对透闪石的溶解影响不大。尾矿砂中橄榄石、蛇纹石和透辉石较容易被硫酸溶解,透闪石、斜长石则比较难溶解,这与尾矿砂中矿物性质有密切关系。     

Acid mine drainage and acid rock drainage processes in the environment of Herrerías Mine (Iberian Pyrite Belt, Huelva-Spain) and impact on the Andevalo Dam

The present work describes the process of acid water discharge into the Andévalo Dam (Iberian Pyrite Belt, Huelva-Spain) starting from the interpretation of rainfall data and chemical analyses regarding pH, conductivity, metal and sulphate content in water, from a time series corresponding to the sampling of two confluent channels that discharge water into the referred dam. Statistical data treatment allows us to conclude the existence of acid mine drainage processes in the Chorrito Stream, which are translated into very low pH values and high sulphate and metal concentrations in the water coming from Herrerías Mine. On the other hand, the Higuereta Stream shows, for the same parameters, much lower values that can be interpreted as the channel response to acid rock drainage processes in its drainage basin induced by the rocky outcrops of the Iberian Pyrite Belt.     

Hydrogeochemical Characteristics of Acid Mine Drainage around the Abandoned Youngdong Coal Mine in Korea

Abstract: To determine the geochemical characteristics of the Imgok creek impacted by acid mine drainage (AMD) generated from the abandoned Youngdong coal mine in Korea, chemical analyses of water samples and precipitates and the geochemical modelling of the precipitates were conducted. Acid mine drainage drained from the mine adit and coal refuse piles shows a low pH, high conductivity and high concentrations of Fe, Al, SO₄ and heavy metals such as Co, Cu, Ni and Zn. In the Imgok creek, the concentrations of heavy metals and major cations besides Fe are decreased by dilution, but concentrations of Fe are decreased by the formation of precipitates as well as dilution. From the results of geochemical modelling, goethite is oversaturated, and schwertmannite is the most stable solid phase in the Imgok creek. Yellowish red Fe-precipitates collected at the Imgok creek are recognized as amorphous or poorly crystallized minerals from XRD patterns and Fe_ox/Fe_totratios, and as containing chemically bonded SO₄ and OH by an IR analysis. The mole ratios of Fe/S in these precipitates, which are determined by EPMA, are 5. 1 and 6. 1.     

Mineralogical and geochemical characterization of the Old Tailings Dam,Australia: Evaluating the effectiveness of a water cover for long-term AMD control

Establishing a shallow water cover over tailings deposited in a designated storage facility is one option to limit oxygen diffusion and retard oxidation of sulfides which have the potential to form acid mine drainage (AMD). The Old Tailings Dam (OTD) located at the Savage River mine, western Tasmania contains 38 million tonnes of pyritic tailings deposited from 1967 to 1982, and is actively generating AMD. The OTD was constructed on a natural gradient, resulting in sub-aerial exposure of the southern area, with the northern area under a natural water cover. This physical contrast allowed for the examination of tailings mineralogy and geochemistry as a function of water cover depth across the OTD. Tailings samples (n = 144, depth: ≤ 1.5 m) were collected and subjected to a range of geochemical and mineralogical evaluations. Tailings from the southern and northern extents of the OTD showed similar AMD potential based on geochemical (NAG pH range: 2.1 to 4.2) and bulk mineralogical parameters, particularly at depth. However, sulfide alteration index (SAI) assessments highlighted the microscale contrast in oxidation. In the sub-aerial zone pyrite grains are moderately oxidized to a depth of 0.3 m (maximum SAI of 6/10), under both gravel fill and oxidized covers, with secondary minerals (e.g., ferrihydrite and goethite) developed along rims and fractures. Beneath this, mildly oxidized pyrite is seen in fresh tailings (SAI = 2.9/10 to 5.8/10). In the sub-aqueous zone, the degree of pyrite oxidation demonstrates a direct relationship with cover depth, with unoxidized, potentially reactive tailings identified from 2.5 m, directly beneath an organic-rich sediment layer (SAI = 0 to 1/10). These findings are broadly similar to other tailings storage facilities e.g., Fox Lake, Sherritt-Gordon ZnCu mine, Canada and Stekenjokk mine, Sweden where water covers up to 2 m have successfully reduced AMD. Whilst geotechnical properties of the OTD restrict the extension of the water cover, pyrite is enriched in cobalt (up to 2.6 wt%) indicating reprocessing of tailings as an alternative management option. Through adoption of an integrated mineralogical and geochemical characterization approach for tailings assessment robust management strategies after mine closure can be developed.     

Transport and sediment–water partitioning of trace metals in acid mine drainage: an example from the abandoned Kwangyang Au–Ag mine area, South Korea

Transport and sediment–water partitioning of trace metals (Cr, Co, Fe, Pb, Cu, Ni, Zn, Cd) in acid mine drainage were studied in two creeks in the Kwangyang Au–Ag mine area, southern part of Korea. Chemical analysis of stream waters and the weak acid (0.1 N HCl) extraction, strong acid (HF–HNO₃–HClO₄) extraction, and sequential extraction of stream sediments were performed. Heavy metal pollution of sediments was higher in Chonam-ri creek than in Sagok-ri creek, because there is a larger source of base metal sulfides in the ores and waste dump upstream of Chonam-ri creek. The sediment–water distribution coefficients (K _d) for metals in both creeks were dependent on the water pH and decreased in the order Pb ≈ Al > Cu > Mn > Zn > Co > Ni ≈ Cd. K _d values for Al, Cu and Zn were very sensitive to changes in pH. The results of sequential extraction indicated that among non-residual fractions, Fe–Mn oxides are most important for retaining trace metals in the sediments. Therefore, the precipitation of Fe(–Mn) oxides due to pH increase in downstream sites plays an important role in regulating the concentrations of dissolved trace metals in both creeks. For Al, Co, Cu, Mn, Pb and Zn, the metal concentrations determined by 0.1 N HCl extraction (Korean Standard Method for Soil Pollution) were almost identical to the cumulative concentrations determined for the first three weakly-bound fractions (exchangeable + bound to carbonates + bound to Fe–Mn oxides) in the sequential extraction procedure. This suggests that 0.1 N HCl extraction can be effectively used to assess the environmentally available and/or bioavailable forms of trace metals in natural stream sediments.     

Characterization of anthropogenic and natural sources of acid rock drainage at the Cinnamon Gulch abandoned mine land inventory site,Summit County,Colorado

Colorado's Cinnamon Gulch releases acid rock drainage (ARD) from anthropogenic and natural sources. In 2001, the total discharge from Cinnamon Gulch was measured at 1.02 cfs (29 L/s) at base flow and 4.3 cfs (122 L/s) at high flow (spring runoff). At base flow, natural sources account for 98% of the discharge from the watershed, and about 96% of the chemical loading. At high flow, natural sources contribute 96% of discharge and 92 to 95% of chemical loading. The pH is acidic throughout the Cinnamon Gulch watershed, ranging from 2.9 to 5.4. At baseflow, nearly all of the trace metals analyzed in the 18 samples exceeded state hardness-dependent water quality standards for aquatic life. Maximum dissolved concentrations of selected constituents included 16 mg/L aluminum, 15 mg/L manganese, 40 mg/L iron, 2 mg/L copper, 560 g/L lead, 8.4 mg/L zinc, and 300 mg/L sulfate. Average dissolved concentrations of selected metals at baseflow were 5.5 mg/L aluminum, 5.5 mg/L manganese, 14 g/L cadmium, 260 g/L copper, 82 g/L lead, and 2.8 mg/L zinc.     

Solid phase characterization and metal deportment in a mussel shell bioreactor for the treatment of AMD,Stockton Coal Mine,New Zealand

The Stockton Coal Mine, located on the West Coast of New Zealand, is evaluating the use of a mussel shell bioreactor (MSB) to treat acidic metalliferous runoff from acid forming overburden. This novel approach is similar in concept to vertical flow wetlands (VFWs) and successive alkalinity producing systems (SAPS). The MSB system is a trapezoidal pit 2 m deep, 35 m long, 3–10 m wide with 60° angle sides. During operation it contained 160 tonnes (240 m³) of mussel shell material and was saturated with a 100–200 mm water cap. Influent flowed through the reactor at a mean rate of 0.3 L s⁻¹ resulting in a hydraulic retention time (HRT) of ≈6 days. The prototype MSB was in operation for a total of 1027 days, from June 2009 through March 2012, and effectively sequestered 99.7% of Al, 99.3% of Fe, 98.8% of Ni, 98.4% Tl and 99.3% of Zn, as determined from a previous evaluation of MSB performance. The MSB also effectively neutralized acidity, which resulted in an increase in influent pH from 2.8 to 6.9 in the effluent. Based on an examination of several excavated pits, five distinct reaction zones developed within the MSB. The reaction zones consisted of an allochthonous sediment layer (0–330 mm), an oxidized iron-rich ocherous layer (at 330–350 mm depth), an aluminum layer (at 350–600 mm depth) with geochemical variations throughout (350–500 mm and 500–600 mm); and a chemically reduced bottom shell layer (at 600–1100 mm). Representative samples were collected from each layer and analyzed using a combination of geochemical and physical methods to assess the stability of the secondary minerals and trace metal deportment within the MSB. Major elements Fe, Al, Ni, Tl, and Zn where preferentially associated with particular layers within the MSB. Elevated concentrations of Fe (110,000 mg kg⁻¹) were observed in the allochthonous sediment and ocherous precipitate layers, while Al (27,816 mg kg⁻¹), Ni (55 mg kg⁻¹), and Zn (655 mg kg⁻¹) were elevated within the aluminum and lower reduced depths within the MSB. Trace Tl (21 mg kg⁻¹) showed varying concentrations throughout the MSB, but was strongly correlated to lower layers of the system. Microbial biofilms were observed within the reduced portions of the shell layers often proximal to bacterial shaped sulfides. The geochemical assessment of the MSB presented in this study is the first of its kind for a MSB, and supports the argument that this system is another viable option for passive treatment of AMD.     

Quantifying the potential for recoverable resources of gallium,germanium and antimony as companion metals in Australia

Although critical to newly evolving and increasingly essential technologies, antimony (Sb), gallium (Ga), and germanium (Ge) are generally recovered as byproducts or ‘companion metals’ of other metal ores. The stage at which companion metals are extracted depends on metallurgical processes by which the host ore mineral is extracted and processed; many companion metals are recovered late during this processing. Therefore, the current and future supply of companion metals relies not only on production of major commodities, but also on the efficient recovery of these metals during processing that recovers the primary commodity.National geological surveys, particularly the USGS, publish annual estimates of global reserves for a variety of primary metals, but generally not for companion metals. This study provides estimates for the geogenic stocks (in waste rock piles, tailings, smelting, and refining) of Ga, Ge, and Sb as companion metals. These elements are mined in Australia but may be recovered outside of Australia, but their life cycles have not yet been well understood.Based on the methodology adapted, this paper estimates a minimum of 970–1230 kt of Ga, 30–10,000 kt of Ge and 70–1000 kt of Sb in current Australian lead-zinc-silver, gold, copper, iron ore, coal, bauxite, and bauxite residue (red mud) resources. The large range of estimated stocks stems from the variable range of ore grades reported by companies and the considerable uncertainty that exists among the grade estimates presented. However, these estimates are reflective of best practice in mineral resource estimation of Ga, Ge, and Sb, and provide a basis for determining similar recoverable resource estimates of other companion metals, such as indium, rhenium, and selenium, all of which are of increasing importance in modern-day life.     

Organic matter maturation under the influence of a deep intrusive heat source: A natural experiment for quantitation of hydrocarbon generation and expulsion from a petroleum source rock (Toarcian shale, northern Germany)

Four shallow boreholes were drilled in the Hils syncline, northern Germany, in order to determine quantitatively the amount of hydrocarbons generated and expelled during maturation of a typical kerogen-type-II-bearing source rock. The holes penetrated the carbonceous Lias shales (Posidonia shale, Lower Toarcian) and part of the adjacent Dogger α and Lias δ mudstones. The maturity of the organic matter in the cores recovered ranges from immature (0.48% R̄₀) to overmature 1.45% R̄₀) due to location of the Hils syncline in the vicinity of the Vlotho Massif, which is deep-seated intrusive body. Facies variations of the Lias within the short geographical distances in the study area are negligible.Organic matter mass balance calculations were based on detailed organic geochemical analyses of residual material in the Lias shales (kerogen, bitumen etc.) and on the evidence of a uniform initial composition of these sediments in the study area. Dead carbon determinations supported this latter criterion but were not used as a parameter in the calculations.About 50% of the initial kerogen was transformed into oil, gas and inorganic compounds during the vitrinite reflectance increase from 0.48 to 0.88% R̄_o and only marginally more during the maturity increase from 0.88 to 1.45% R̄_o. Only a small portion of the generated material remained in the source rock even at a relatively early stage of generation (0.68% R̄_o). Expulsion efficiency of oil plus gas reached a value of 86% at the end of the main generation stage (0.88% R̄_o).