The dilatant behaviour of sand–pile interface subjected to loading and stress relief

Property and behaviour of sand–pile interface are crucial to shaft resistance of piles. Dilation or contraction of the interface soil induces change in normal stress, which in turn influences the shear stress mobilised at the interface. Although previous studies have demonstrated this mechanism by laboratory tests and numerical simulations, the interface responses are not analysed systematically in terms of soil state (i.e. density and stress level). The objective of this study is to understand and quantify any increase in normal stress of different pile–soil interfaces when they are subjected to loading and stress relief. Distinct element modelling was carried out. Input parameters and modelling procedure were verified by experimental data from laboratory element tests. Parametric simulations of shearbox tests were conducted under the constant normal stiffness, constant normal load and constant volume boundary conditions. Key parameters including initial normal stress ( $ \sigma_{{{\text{n}}0}}^{\prime } $ ), initial void ratio (e ₀), normal stiffness constraining the interface and loading–unloading stress history were investigated. It is shown that mobilised stress ratio ( $ \tau /\sigma_{\text{n}}^{\prime } $ ) and normal stress increment ( $ \Updelta \sigma_{\text{n}}^{\prime } $ ) on a given interface are governed by $ \sigma_{{{\text{n}}0}}^{\prime } $ and e ₀. An increase in $ \sigma_{{{\text{n}}0}}^{\prime } $ from 100 to 400 kPa leads to a 30 % reduction in $ \Updelta \sigma_{\text{n}}^{\prime } $ . An increase in e ₀ from 0.18 to 0.30 reduces $ \Updelta \sigma_{\text{n}}^{\prime } $ by more than 90 %, and therefore, shaft resistance is much lower for piles in loose sands. A unique relationship between $ \Updelta \sigma_{\text{n}}^{\prime } $ and normal stiffness is established for different soil states. It can be applied to assess the shaft resistance of piles in soils with different densities and subjected to loading and stress relief. Fairly good agreement is obtained between the calculated shaft resistance based on the proposed relationship and the measured results in centrifuge model tests.     

Petrological cannibalism: the chemical and textural consequences of incremental magma body growth

The textures of minerals in volcanic and plutonic rocks testify to a complexity of processes in their formation that is at odds with simple geochemical models of igneous differentiation. Zoning in plagioclase feldspar is a case in point. Very slow diffusion of the major components in plagioclase means that textural evidence for complex magmatic evolution is preserved, almost without modification. Consequently, plagioclase affords considerable insight into the processes by which magmas accumulate in the crust prior to their eventual eruption or solidification. Here, we use the example of the 1980–1986 eruptions of Mount St. Helens to explore the causes of textural complexity in plagioclase and associated trapped melt inclusions. Textures of individual crystals are consistent with multiple heating and cooling events; changes in total pressure (P) or volatile pressure ( $P_{{{\text{H}}_{ 2} {\text{O}}}}$ P H 2 O ) are less easy to assess from textures alone. We show that by allying textural and chemical analyses of plagioclase and melt inclusions, including volatiles (H₂O, CO₂) and slow-diffusing trace elements (Sr, Ba), to published experimental studies of Mount St. Helens magmas, it is possible to disambiguate the roles of pressure and temperature to reconstruct magmatic evolutionary pathways through temperature–pressure–melt fraction (T– $P_{{{\text{H}}_{ 2} {\text{O}}}}$ P H 2 O –F) space. Our modeled crystals indicate that (1) crystallization starts at $P_{{{\text{H}}_{ 2} {\text{O}}}}$ P H 2 O  > 300 MPa, consistent with prior estimates from melt inclusion volatile contents, (2) crystal cores grow at $P_{{{\text{H}}_{ 2} {\text{O}}}}$ P H 2 O  = 200–280 MPa at F = 0.65–0.7, (3) crystals are transferred to $P_{{{\text{H}}_{ 2} {\text{O}}}}$ P H 2 O  = 100–130 MPa (often accompanied by 10–20 °C of heating), where they grow albitic rims of varying thicknesses, and (4) the last stage of crystallization occurs after minor heating at $P_{{{\text{H}}_{ 2} {\text{O}}}}$ P H 2 O  ~ 100 MPa to produce characteristic rim compositions of An₅₀. We hypothesize that modeled $P_{{{\text{H}}_{ 2} {\text{O}}}}$ P H 2 O decreases in excess of ~50 MPa most likely represent upward transport through the magmatic system. Small variations in modeled $P_{{{\text{H}}_{ 2} {\text{O}}}}$ P H 2 O , in contrast, can be effected by fluxing the reservoir with CO₂-rich vapors that are either released from deeper in the system or transported with the recharge magma. Temperature fluctuations of 20–40 °C, on the other hand, are an inevitable consequence of incremental, or pulsed, assembly of crustal magma bodies wherein each pulse interacts with ancestral, stored magmas. We venture that this “petrological cannibalism” accounts for much of the plagioclase zoning and textural complexity seen not only at Mount St. Helens but also at arc magmas generally. More broadly we suggest that the magma reservoir below Mount St. Helens is dominated by crystal mush and fed by frequent inputs of hotter, but compositionally similar, magma, coupled with episodes of magma ascent from one storage region to another. This view both accords with other independent constraints on the subvolcanic system at Mount St. Helens and supports an emerging view of many active magmatic systems as dominantly super-solidus, rather than subliquidus, bodies.     

Thermal equation of state of synthetic orthoferrosilite at lunar pressures and temperatures

Iron-rich orthopyroxene plays an important role in models of the thermal and magmatic evolution of the Moon, but its density at high pressure and high temperature is not well-constrained. We present in situ measurements of the unit-cell volume of a synthetic polycrystalline end-member orthoferrosilite (FeSiO₃, fs) at simultaneous high pressures (3.4–4.8 GPa) and high temperatures (1,148–1,448 K), to improve constraints on the density of orthopyroxene in the lunar interior. Unit-cell volumes were determined through in situ energy-dispersive synchrotron X-ray diffraction in a multi-anvil press, using MgO as a pressure marker. Our volume data were fitted to a high-temperature Birch–Murnaghan equation of state (EoS). Experimental data are reproduced accurately, with a  $\varDelta P$ Δ P  standard deviation of 0.20 GPa. The resulting thermoelastic parameters of fs are: V ₀ = 875.8 ± 1.4 Å³, K ₀ = 74.4 ± 5.3 GPa, and $\frac{{\text d}K}{{\text d}T} = -0.032 \pm 0.005\,\hbox{GPa K}^{-1}$ d K d T = - 0.032 ± 0.005 GPa K - 1 , assuming ${K}^{\prime}_{0} = 10 $ K 0 ′ = 10 . We also determined the thermal equation of state of a natural Fe-rich orthopyroxene from Hidra (Norway) to assess the effect of magnesium on the EoS of iron-rich orthopyroxene. Comparison between our two data sets and literature studies shows good agreement for room-temperature, room-pressure unit-cell volumes. Preliminary thermodynamic analyses of orthoferrosilite, FeSiO₃, and orthopyroxene solid solutions, (Mg_1?x Fe _x ) SiO₃, using vibrational models show that our volume measurements in pressure–temperature space are consistent with previous heat capacity and one-bar volume–temperature measurements. The isothermal bulk modulus at ambient conditions derived from our measurements is smaller than values presented in the literature. This new simultaneous high-pressure, high-temperature data are specifically useful for calculations of the orthopyroxene density in the Moon.     

Foundation Stability of a Levee

Stability of a levee and its foundation soil during flood is governed by seepage forces. In this study, the seepage forces in the flow domain have been determined using conformal mapping technique. Stability of foundation soil has been studied for a levee with and without cut-off wall on permeable soil of infinite depth. In situ effective normal and shear stresses due to self-weight, additional induced stresses due to levee structure and ponded water on upstream sloping face have been determined by assuming soil to be elastic. Besides, components of seepage stress acting at a point on two orthogonal planes, i.e., on vertical and horizontal planes, are considered and the Mohr’s circle is drawn. Mohr–Coulomb failure envelope is drawn for the foundation soil with known effective cohesion ( $c^{\prime}_{1}$ c 1 ′ ) and angle of internal friction ( $\varphi^{\prime}_{1}$ φ 1 ′ ), and then the stability of the foundation soil has been assessed. Probable zone of general shear failure considering seepage flow has been identified. Zones vulnerable to foundation failure for different width of levee and depth of cut-off wall have been computed. The hydraulic unstable zone in downstream side of the levee resembles a log spiral. The provision of cut-off wall restricts the progress of failure zone only in the downstream side; otherwise, the zone of failure will enter the foundation of the levee. The stability of the foundation soil of an existing ring levee along the rivers Ganga, Sone and Punpun, near Patna (India), has been evaluated.     

The P–V–T equation of state of CaPtO3 post-perovskite

Orthorhombic post-perovskite CaPtO₃ is isostructural with post-perovskite MgSiO₃, a deep-Earth phase stable only above 100 GPa. Energy-dispersive X-ray diffraction data (to 9.4 GPa and 1,024 K) for CaPtO₃ have been combined with published isothermal and isobaric measurements to determine its P–V–T equation of state (EoS). A third-order Birch–Murnaghan EoS was used, with the volumetric thermal expansion coefficient (at atmospheric pressure) represented by α(T) = α₀ + α₁(T). The fitted parameters had values: isothermal incompressibility, $ K_{{T_{0} }} $  = 168.4(3) GPa; $ K_{{T_{0} }}^{\prime } $  = 4.48(3) (both at 298 K); $ \partial K_{{T_{0} }} /\partial T $  = ?0.032(3) GPa K^?1; α₀ = 2.32(2) × 10^?5 K^?1; α₁ = 5.7(4) × 10^?9 K^?2. The volumetric isothermal Anderson–Grüneisen parameter, δ _T , is 7.6(7) at 298 K. $ \partial K_{{T_{0} }} /\partial T $ for CaPtO₃ is similar to that recently reported for CaIrO₃, differing significantly from values found at high pressure for MgSiO₃ post-perovskite (?0.0085(11) to ?0.024 GPa K^?1). We also report axial P–V–T EoS of similar form, the first for any post-perovskite. Fitted to the cubes of the axes, these gave $ \partial K_{{aT_{0} }} /\partial T $  = ?0.038(4) GPa K^?1; $ \partial K_{{bT_{0} }} /\partial T $  = ?0.021(2) GPa K^?1; $ \partial K_{{cT_{0} }} /\partial T $  = ?0.026(5) GPa K^?1, with δ _T  = 8.9(9), 7.4(7) and 4.6(9) for a, b and c, respectively. Although $ K_{{T_{0} }} $ is lowest for the b-axis, its incompressibility is the least temperature dependent.     

Crystallographic preferred orientation in wüstite (FeO) through the cubic-to-rhombohedral phase transition

Magnesiowüstite, (Mg_0.08Fe_0.88)O, and wüstite, Fe_0.94O, were compressed to ~36?GPa at ambient temperature in the diamond anvil cell (DAC) at the Advanced Light Source. X-ray diffraction patterns were taken in situ in radial geometry in order to study the evolution of crystallographic preferred orientation through the cubic-to-rhombohedral phase transition. Under uniaxial stress in the DAC, {100}_c planes aligned perpendicular to the compression direction. The {100}_c in cubic became { $\left\{ {10\bar 14} \right\}$ }_r in rhombohedral and remained aligned perpendicular to the compression direction. However, the {101}_c and {111}_c planes in the cubic phase split into { ${10{\bar{1}}4}$ }_r and { ${11{\bar{2}}0}$ }_r, and (0001)_r and { ${10{\bar{1}}1}$ }_r, respectively, in the rhombohedral phase. The { ${11{\bar{2}}0}$ }_r planes preferentially aligned perpendicular to the compression direction while { ${10{\bar{1}}4}$ }_r oriented at a low angle to the compression direction. Similarly, { ${10{\bar{1}}1}$ }_r showed a slight preference to align more closely perpendicular to the compression direction than (0001)_r. This variant selection may occur because the 〈 ${10{\bar{1}}4}$ 〉_r and [0001]_r directions are the softer of the two sets of directions. The rhombohedral texture distortion may also be due to subsequent deformation. Indeed, polycrystal plasticity simulations indicate that for preferred { ${10{\bar{1}}4}$ }〈 ${1{\bar{2}}10}$ 〉_r and { ${11{\bar{2}}0}$ }〈 ${{\bar{1}}101}$ 〉_r slip and slightly less active { ${10{\bar{1}}1}$ }〈 ${{\bar{1}}2{\bar{1}}0}$ 〉_r slip, the observed texture pattern can be obtained.     

High temperature calorimetry of sulfide systems

The standard enthalpies of formation of FeS (troilite), FeS₂ (pyrite), Co_0.9342S, Co₃S₄ (linnaeite), Co₉S₈ (cobalt pentlandite), CoS₂ (cattierite), CuS (covellite), and Cu₂S (chalcocite) have been determined by high temperature direct reaction calorimetry at temperatures between 700 K and 1021 K. The following results are reported: $$\Delta {\rm H}_{f,FeS}^{tr} = - 102.59 \pm 0.20kJ mol^{ - 1} ,$$ $$\Delta {\rm H}_{f,FeS}^{py} = - 171.64 \pm 0.93kJ mol^{ - 1} ,$$ $$\Delta {\rm H}_{f,Co_{0.934} S} = - 99.42 \pm 1.52kJ mol^{ - 1} ,$$ $$\Delta {\rm H}_{f,Co_9 S_8 }^{ptl} = - 885.66 \pm 16.83kJ mol^{ - 1} ,$$ $$\Delta {\rm H}_{f,Co_3 S_4 }^{In} = - 347.47 \pm 7.27kJ mol^{ - 1} ,$$ $$\Delta {\rm H}_{f,CoS_2 }^{ct} = - 150.94 \pm 4.85kJ mol^{ - 1} ,$$ $$\Delta {\rm H}_{f,Cu_2 S}^{cc} = - 80.21 \pm 1.51kJ mol^{ - 1} ,$$ and $$\Delta {\rm H}_{f,CuS}^{cv} = - 53.14 \pm 2.28kJ mol^{ - 1} ,$$ The enthalpy of formation of CuFeS₂ (chalcopyrite) from (CuS+FeS) and from (Cu+FeS₂) was determined by solution calorimetry in a liquid Ni_0.60S_0.40 melt at 1100 K. The results of these measurements were combined with the standard enthalpies of formation of CuS, FeS, and FeS₂, to calculate the standard enthalpy of formation of CuFeS₂. We found \(\Delta {\rm H}_{f,CuFeS_2 }^{ccp} = - 194.93 \pm 4.84kJ mol^{ - 1}\) . Our results are compared with earlier data given in the literature; generally the agreement is good and our values agree with previous estimates within the uncertainties present in both.     

Physical conditions in faint gigahertz-peaked spectrum radio sources

Weak, compact radio sources (～100 mJy peak flux, L～1–10 pc) with their spectral peaks at about a gigahertz are studied, based on the complete sample of 46 radio sources of Snellen, drawn from high-sensitivity surveys, including the low-frequency Westerbork catalog. The physical parameters have been estimated for 14 sources: the magnetic field (H _⊥), the number density of relativistic particles (n _e), the energy of the magnetic field $(E_{H_ \bot } )$ , and the energy of relativistic particles (E _e). Ten sources have $E_{H_ \bot } \ll E_e $ , three have approximate equipartition of the energies $(E_{H_ \bot } \sim E_e )$ , and only one has $E_{H_ \bot } \gg E_e $ . The mean magnetic fields in quasars (10^?3 G) and galaxies (10^?2 G) have been estimated. The magnetic field appears to be related to the sizes of compact features as $H \sim 1/\sqrt L $ .     

A multi-isotope approach for understanding sources of water,carbon and sulfur in natural springs of the Central Appalachian region

Natural springs have been reliable sources of domestic water and have allowed for the development of recreational facilities and resorts in the Central Appalachians. The structural history of this area is complex and it is unknown whether these natural springs receive significant recharge from modern precipitation or whether they discharge old water recharged over geological times scales. The main objective of this study was to use stable isotopes of water ( $\delta^{18} {\text{O}}_{{{\text{H}}_{2} {\text{O}}}}$ and $\delta^{2} {\text{H}}_{{{\text{H}}_{2} {\text{O}}}}$ ), dissolved inorganic carbon ( $\delta^{13} {\text{C}}_{\text{DIC}}$ ) and dissolved sulfate ( $\delta^{34} {\text{S}}_{{{\text{SO}}_{4} }}$ and $\delta^{18} {\text{O}}_{{{\text{SO}}_{4} }}$ ) to delineate sources of water, carbon and sulfur in several natural springs of the region. Our preliminary isotope data indicate that all springs are being recharged by modern precipitation. The oxygen isotope composition indicates that waters in thermal springs did not encounter the high temperatures required for O isotope exchange between the water and silicate/carbonate minerals, and/or the residence time of water in the aquifers was short due to high flow rates. The carbon isotopic composition of dissolved inorganic carbon and sulfur/oxygen isotopic composition of dissolved sulfate provide evidence of low-temperature water–rock interactions and various biogeochemical transformations these waters have undergone along their flow path.     

A micro-Mössbauer study of chromites included in diamond and other mantle-related rocks

Oxygen fugacity ( $ f_{{{\text{O}}_{ 2} }} $ f O 2 ) is a fundamental but little known intensive variable in mantle processes. It influences the P/T position of a mantle solidus and the composition of mantle-derived melts and fluids and constrains mantle-core equilibria and a number of geophysical properties of the mantle. An important source of information on oxidation states is the ferric–ferrous iron ratio in mantle spinels. Since the magnetite component is low in mantle spinels, normal analytical errors translate into considerable $ f_{{{\text{O}}_{ 2} }} $ f O 2 uncertainties. In this study, we analyzed the Fe³⁺–Fe_tot ratio of chromites present as inclusions in diamond and other mantle-related occurrences by point-source Mössbauer spectroscopy using single-crystal absorbers as well as conventional Mössbauer spectroscopy using powder absorbers. The studied spinels have been previously analyzed by single-crystal X-ray diffraction and electron microprobe. The ferric–ferrous ratios found are normally similar to the different techniques apart from some samples where a large number of grains have been used for the analyses (powder absorbers). The general agreement between the different techniques allows us to conclude that the studied chromites are stoichiometric. However, conventional Mössbauer spectroscopy on powder absorbers should be conducted with great care, since the method requires a relatively large amount of sample material. Spinel frequently occurs as small grains, and the large number of crystals required may possess different degrees of oxidation/alteration and, consequently, different ferric–ferrous ratio leading to possible errors in the interpretation of the results.     

Experimental Investigation of Seepage Properties of Fractured Rocks Under Different Confining Pressures

The effectiveness of transmitting underground water in rock fractures is strongly influenced by the widths of the fractures and their interconnections. However, the geometries needed for water flow in fractured rock are also heavily controlled by the confining pressure conditions. This paper is intended to study the seepage properties of fractured rocks under different confining pressures. In order to do this, we designed and manufactured a water flow apparatus that can be connected to the electro-hydraulic servo-controlled test system MTS815.02, which provides loading and exhibits external pressures in the test. Using this apparatus, we tested fractured mudstone, limestone and sandstone specimens and obtained the relationship between seepage properties and variations in confining pressure. The calculation of the seepage properties based on the collection of water flow and confining pressure differences is specifically influenced by non-Darcy flow. The results show that: (1) The seepage properties of fractured rocks are related to confining pressure, i.e. with the increase of confining pressure, the permeability $ k $ decreases and the absolute value of non-Darcy flow coefficient $ \beta $ increases. (2) The sandstone coefficients $ k $ and $ \beta $ range from $ 1.03 \times 10^{ - 18} $ to $ 1.53 \times 10^{ - 17} $  m² and $ - 1.13 \times 10^{17} $ to $ - 2.35 \times 10^{18} $  m^?1, respectively, and exhibit a greater change compared to coefficients of mudstone and limestone. (3) From the regression analysis of experimental data, it is concluded that the polynomial function is a better fit than the power and logarithmic functions. The results obtained can provide an important reference for understanding the stability of rock surrounding roadways toward prevention of underground water gushing-out, and for developing underground resources (e.g. coal).     

Dislocation-assisted diffusion of oxygen in albite

Oxygen diffusion in albite has been determined by the integrating (bulk ¹⁸O) method between 750° and 450° C, for a P _H2O of 2 kb. The original material has a low dislocation density (<10⁶ cm^?2), and its lattice diffusion coefficient (D ₁), given below, agrees well with previous determinations. A sample was deformed at high temperature and pressure to produce a uniform dislocation density of 5 × 10⁹ cm^?2. The diffusion coefficient (D _a) for this deformed material, given below, is about 0.5 and 0.7 orders of magnitude larger than D ₁ at 700° and 450° C, respectively. This enhancement is believed due to faster diffusion along the cores of dislocations. Assuming a dislocation core radius of 4 Å, the calculated pipe diffusion coefficient (D _p), given below, is about 5 orders of magnitude larger than D ₁. These results suggest that volume diffusion at metamorphic conditions may be only slightly enhanced by the presence of dislocations. $$\begin{gathered} D_1 = 9.8 \pm 6.9 \times 10^{ - 6} (cm^2 /\sec ) \hfill \\ {\text{ }} \cdot \exp [ - 33.4 \pm 0.6(kcal/mole)/RT] \hfill \\ \end{gathered} $$ $$\begin{gathered} D_a = 7.6 \pm 4.0 \times 10^{ - 6} (cm^2 /\sec ) \hfill \\ {\text{ }} \cdot \exp [ - 30.9 \pm 1.1(kcal/mole)/RT] \hfill \\ \end{gathered} $$ $$\begin{gathered} D_p \approx 1.2 \times 10^{ - 1} (cm^2 /\sec ) \hfill \\ {\text{ }} \cdot \exp [ - 29.8(kcal/mole)/RT]. \hfill \\ \end{gathered} $$      

The calcium oxotellurate(IV) nitrates Ca5Te4O12(NO3)2(H2O)2 and Ca6Te5O15(NO3)2

Single crystals of two novel calcium oxotellurate(IV) nitrates were grown under hydrothermal conditions and were structurally characterized by X-ray diffraction. Ca $_5$ Te $_4\text {O}_{12}$ (NO $_3$ ) $_2$ (H $_2$ O) $_2$ [ $Cc$ , $Z=4$ , $a=25.258(3)$ Å, $b=5.7289(7)$ Å, $c=17.0066(19)$ Å, $\beta =124.377(2)^{\circ}$ , $R[F^2 > 2\sigma (F^2)]=0.043$ , 4083 $F^2$ data, 281 parameters] can be described as a non-classic order/disorder (OD) structure, which fulfills the basic principle of OD theory, viz. local equivalence of polytypes, but does not strictly follow the vicinity condition (VC) of OD theory. The structure is made up from an alternating stacking of non-polar layers composed of isolated [TeO $_3$ ] units and Ca $^{2+}$ ions and polar layers containing NO $_3^-$ ions and water molecules. The electron lone-pairs of the [TeO $_3$ ] units protrude into the free space of the anion/water layers. The crystal under investigation was a non-classic OD-twin of domains of a maximum degree of order (MDO). At the twin plane a fragment of the second MDO polytype is located. The main building blocks of Ca $_6$ Te $_5\text {O}_{15}$ (NO $_3$ ) $_2$ [ $P2_1/c$ , $Z=4$ , $a=15.494(2)$ Å, $b=5.6145(7)$ Å, $c=39.338(4)$ Å, $\beta =142.480(5)^{\circ}$ , $R[F^2 > 2\sigma (F^2)]=0.043$ , 3026 $F^2$ data, 307 parameters] are isolated [TeO $_3$ ] units and Ca $^{2+}$ ions which are connected to a three-dimensional framework perforated by channels in which the N atoms of the nitrate anions are located and the electron lone-pairs of the [TeO $_3$ ] units protrude. The structure can topologically be derived from the structure of Ca $_5$ Te $_4\text {O}_{12}$ (NO $_3$ ) $_2$ (H $_2$ O) $_2$ by removing the water molecules and connecting the CaTeO $_3$ layers with additional [TeO $_3$ ] units and Ca $^{2+}$ ions.     

P wave attenuation structure beneath the Kanto district and surrounding area, Japan

Spectral ratios of teleseismic P waves for 15 deep (>200 km) earthquakes recorded at 146 High-Sensitivity Seismographic Network stations in the Kanto district and its surrounding area, eastern Japan, were inverted for attenuation parameter $ t_P^{ * } $ . The dataset consisted of good-quality vertical-component seismograms, whose P phases were handpicked. The P wave spectral ratios with high signal-to-noise ratios were calculated up to 1 Hz for all the station pairs, linear regressed, and then inverted for $ t_P^{ * } $ using the technique of least squares . The result showed that the active volcanic areas were clearly characterized by high $ t_P^{ * } $ . In contrast, $ t_P^{ * } $ varied in the nonvolcanic areas. The present result on the $ t_P^{ * } $ distribution was roughly consistent with the shallow part (<30 km) of an attenuation structure, which has been previously obtained based on 3-D tomography by using records of high-frequency (around 5 Hz) P waves from local earthquakes. This suggested that the present method of $ t_P^{ * } $ estimation is valid. The advantage and possible application to other areas were also discussed.     

Metasomatic interaction between rock and solution under varying pressure-temperature conditions

Variations in the activity of major components in a rock and solution initially equilibrated with the activity were evaluated under thermal and pressure gradient conditions by the example of the system granite-chloride solution. These variations are controlled by the shifts of mineral hydrolysis reactions in the rock and dissociation equilibria of salts, acids, and bases in the solution. The resulting relationships between $a_{Me^ + } /a_{H^ + }^{sol} $ and $a_{Me^ + } /a_{H^ + }^{rock} $ control the direction of infiltration metasomatism. There is a high-temperature region, where the behavior of Mg and Fe is very different from that of Na and K and the behavior of Ca is transitional, and a low-temperature region, where these components are similar to each other. The processes of acidic and alkalic metasomatism may be accompanied in various combinations by the processes of basification and debasification, as well as rock silicification and desilication. The type of these combinations is controlled by the character of the gradient field, involving either a decrease or an increase in temperature and pressure, and can be correlated with a particular metasomatic association.     

Biradical states of oxygen-vacancy defects in ��-quartz: centers E_{2}^{\prime \prime } and E_{4}^{\prime \prime }

Several new radiation defects with total electron spin S?=?1 occurring in electron-irradiated, synthetic ??-quartz have been observed by using electron paramagnetic resonance spectroscopy. These defects are considered to be biradicals, i.e., pairs of S?=?1/2 species. The concentration of these centers depends on the condition of the fast-electron irradiation. They have different decay behaviors that allow measurements of any individual species especially when it predominates over the others. The primary spin Hamiltonian parameter matrices g ₁, g ₂, D have now been determined for two similar defects, which herein are labeled $ E_{2}^{\prime \prime } $ and $ E_{4}^{\prime \prime } $ . Inter-electron distances estimated by using the magnetic dipole model, suggest that the structures of centers $ E_{2}^{\prime \prime } $ and $ E_{4}^{\prime \prime } $ both involve the unpaired electrons each located in orbitals of two silicon atoms next to a common oxygen vacancy but which have slightly different Si?CSi distances at 0.90 and 0.79?nm, respectively. This model is consistent with previous DFT calculations of the triplet configurations with local energetic minima. Observed decay behaviors suggest a transformation of centers $ E_{2,4}^{\prime \prime } $ to the analogous $ E_{1}^{\prime \prime } $ center. These triplet centers in quartz provide new insights into the structures of analogous defects in amorphous silica.     

The concept of geochemical potential field exemplified by ore formation field

Geochemical potential field is defined as the scope within the earth’s space where a given component in a certain phase of a certain material system is acted upon by a diffusion force, depending on its spatial coordinatesX, Y andZ. The three coordinates follow the relations: $$NF_{ix} = - \frac{{\partial \mu }}{{\partial x}}, NF_{iy} = - \frac{{\partial \mu }}{{\partial y}}, NF_{iz} = - \frac{{\partial \mu }}{{\partial z}}$$ The characteristics of such a field can be summarized as: (1) The summation of geochemical potentials related to the coordinatesX, Y, Z, or pseudo-velocity head, pseudo-pressure head and pseudo-potential head of a certain component in the earth is a constant as given by $$\mu _x + \mu _y + \mu _z = c$$ or $$\mu _{x2} + \mu _{y2} + \mu _{z2} = \mu _{x1} + \mu _{y1} + \mu _{z1} $$ Derived from these relations is the principle of geochemical potential conservation. The following relations have the same physical significance: $$\mu _k + \mu _u + \mu _p = c$$ or $$\mu _{k2} + \mu _{u2} + \mu _{p2} = \mu _{k1} + \mu _{u1} + \mu _{p1} $$ (2) Geochemical potential field is a vector field quantified by geochemical field intensity which is defined as the diffusion force applied to one molecular volume (or one atomic volume) of a certain component moving from its higher concentration phase to lower concentration phase. The geochemical potential field intensity is given by $$\begin{gathered} E = - grad\mu \hfill \\ E = \frac{{RT}}{x}i + \frac{{RT}}{y}j + \frac{{RT}}{z}K \hfill \\ \end{gathered} $$ The present theory has been inferred to interpret the mechanism of formation of some tungsten ore deposits in China.     

Thermodynamic properties of andradite and application to skarn with coexisting andradite and hedenbergite

The enthalpy of formation of andradite (Ca₃Fe₂Si₃O₁₂) has been estimated as-5,769.700 (±5) kJ/mol from a consideration of the calorimetric data on entropy (316.4 J/mol K) and of the experimental phaseequilibrium data on the reactions: 1 $$\begin{gathered} 9/2 CaFeSi_2 O_6 + O_2 = 3/2 Ca_3 Fe_2 Si_3 O_{12} + 1/2 Fe_3 O_4 + 9/2 SiO_2 (a) \hfill \\ Hedenbergite andradite magnetite quartz \hfill \\ \end{gathered} $$ 1 $$\begin{gathered} 4 CaFeSi_2 O_6 + 2 CaSiO_3 + O_2 = 2 Ca_3 Fe_2 Si_3 O_{12} + 4 SiO_2 (b) \hfill \\ Hedenbergite wollastonite andradite quartz \hfill \\ \end{gathered} $$ 1 $$\begin{gathered} 18 CaSiO_3 + 4 Fe_3 O_4 + O_2 = 6Ca_3 Fe_2 Si_3 O_{12} (c) \hfill \\ Wollastonite magnetite andradite \hfill \\ \end{gathered} $$ 1 $$\begin{gathered} Ca_3 Fe_2 Si_3 O_{12} = 3 CaSiO_3 + Fe_2 O_3 . (d) \hfill \\ Andradite pseudowollastonite hematite \hfill \\ \end{gathered} $$ and $$log f_{O_2 } = E + A + B/T + D(P - 1)/T + C log f_{O_2 } .$$ Oxygen-barometric scales are presented as follows: $$\begin{gathered} E = 12.51; D = 0.078; \hfill \\ A = 3 log X_{Ad} - 4.5 log X_{Hd} ; C = 0; \hfill \\ B = - 27,576 - 1,007(1 - X_{Ad} )^2 - 1,476(1 - X_{Hd} )^2 . \hfill \\ \end{gathered} $$ For the assemblage andradite (Ad)-hedenbergite (Hd)-magnetite-quartz: $$\begin{gathered} E = 13.98; D = 0.0081; \hfill \\ A = 4 log(X_{Ad} / X_{Hd} ); C = 0; \hfill \\ B = - 29,161 - 1,342.8(1 - X_{Ad} )^2 - 1,312(1 - X_{Hd} )^2 . \hfill \\ \end{gathered} $$ For the assemblage andradite-hedenbergite-wollastonite-quartz: 1 $$\begin{gathered} E = 13.98;{\text{ }}D = 0.0081; \hfill \\ A = 4\log (X_{Ad} /X_{Hd} );{\text{ C = 0;}} \hfill \\ B = - 29,161 - 1,342.8(1 - X_{Ad} )^2 - 1,312(1 - X_{Hd} )^2 . \hfill \\ \end{gathered} $$ For the assemblage andradite-hedenbergite-calcitequartz: 1 $$\begin{gathered} E = - 1.69;{\text{ }}D = - 0.199; \hfill \\ A = 4\log (X_{Ad} /X_{Hd} );{\text{ C = 2;}} \hfill \\ B = - 20,441 - 1,342.8(1 - X_{Ad} )^2 - 1,312(1 - X_{Hd} )^2 . \hfill \\ \end{gathered} $$ For the assemblage andradite-hedenbergite-wollastonite-calcite: 1 $$\begin{gathered} E = - 17.36;{\text{ }}D = - 0.403; \hfill \\ A = 4\log (X_{Ad} /X_{Hd} );{\text{ C = 4;}} \hfill \\ B = - 11,720 - 1,342.8(1 - X_{Ad} )^2 - 1,312(1 - X_{Hd} )^2 \hfill \\ \end{gathered} $$ The oxygen fugacity of formation of those skarns where andradite and hedenbergite assemblage is typical can be calculated by using the above equations. The oxygen fugacity of formation of this kind of skarn ranges between carbon dioxide/graphite and hematite/magnetite buffers. It increases from the inside zones to the outside zones, and appears to decrease with the ore-types in the order Cu, Pb?Zn, Fe, Mo, W(Sn) ore deposits.     

High-temperature deformation of forsterite single crystals doped with vanadium

Creep experiments have been performed on samples from a single crystal of vanadium-doped forsterite under controlled \(p_{{\text{O}}_2 } \) conditions to investigate the effects of the addition of substitutional defects in the tetrahedral lattice sites. The addition of vanadium causes marked changes in the flow behavior of the forsterite, with a net increase in the creep rate at high \(p_{{\text{O}}_2 } \) and a new \(p_{{\text{O}}_2 } \) -dependent flow regime at low \(p_{{\text{O}}_2 } \) conditions. These observations can be interpreted as resulting from changes in the majority defect species that maintain the charge neutrality within the crystal. A climb-controlled dislocation creep model for the high-temperature deformation of vanadium-doped forsterite is proposed in which either (i) movement of uncharged jogs is rate-limited by the diffusion of silicon via a vacancy mechanism or (ii) movement of positively charged jogs is rate-limited by diffusion of oxygen via a vacancy mechanism.     

Transmission electron microscopy of experimentally deformed chalcopyrite single crystals

Two crystals of natural chalcopyrite, CuFeS₂, experimentally deformed at 200° C have been studied by means of transmission electron microscopy (TEM). The activated glide planes are (001) and {112}. The dislocations in (001) have the Burgers vector [110] and a predominating edge character. They are split into two colinear partials b=1/2[110] and can cross split into {112}. The dislocations in {112} consist of straight segments along low index lattice lines. They are often arranged in dipoles generating trails of loops. Few dislocations with b=1/2[ \(\overline {11} \) 1] and [1 \(\bar 1\) 0] are present and dislocations with b=[0 \(\bar 2\) 1] occur in low angle subgrain boundaries. From weak beam contrasts it is presumed that most of the dislocations gliding in {112} have b=1/2〈3 \(\overline {11} \) 〉. They are dissociated into up to four partials. Microtwins and different types of stacking faults in {112} also occur. Models of the dissociation of dislocations are discussed.