Probabilistic seismic hazard assessment for Thailand

A set of probabilistic seismic hazard maps for Thailand has been derived using procedures developed for the latest US National Seismic Hazard Maps. In contrast to earlier hazard maps for this region, which are mostly computed using seismic source zone delineations, the presented maps are based on the combination of smoothed gridded seismicity, crustal-fault, and subduction source models. Thailand’s composite earthquake catalogue is revisited and expanded, covering a study area limited by 0°–30°N Latitude and 88°–110°E Longitude and the instrumental period from 1912 to 2007. The long-term slip rates and estimates of earthquake size from paleoseismological studies are incorporated through a crustal fault source model. Furthermore, the subduction source model is used to model the megathrust Sunda subduction zones, with variable characteristics along the strike of the faults. Epistemic uncertainty is taken into consideration by the logic tree framework incorporating basic quantities, such as different source modelling, maximum cut-off magnitudes and ground motion prediction equations. The ground motion hazard map is presented over a 10 km grid in terms of peak ground acceleration and spectral acceleration at 0.2, 1.0, and 2.0 undamped natural periods and a 5% critical damping ratio for 10 and 2% probabilities of exceedance in 50 years. The presented maps give expected ground motions that are based on more extensive data sources than applied in the development of previous maps. The main findings are that northern and western Thailand are subjected to the highest hazard. The largest contributors to short- and long-period ground motion hazard in the Bangkok region are from the nearby active faults and Sunda subduction zones, respectively.     

Probabilistic seismic hazard assessment for South-Eastern France

The accurate evaluation and appropriate treatment of uncertainties is of primary importance in modern probabilistic seismic hazard assessment (PSHA). One of the objectives of the SIGMA project was to establish a framework to improve knowledge and data on two target regions characterized by low-to-moderate seismic activity. In this paper, for South-Eastern France, we present the final PSHA performed within the SIGMA project. A new earthquake catalogue for France covering instrumental and historical periods was used for the calculation of the magnitude-frequency distributions. The hazard model incorporates area sources, smoothed seismicity and a 3D faults model. A set of recently developed ground motion prediction equations (GMPEs) from global and regional data, evaluated as adequately representing the ground motion characteristics in the region, was used to calculate the hazard. The magnitude-frequency distributions, maximum magnitude, faults slip rate and style-of-faulting are considered as additional source of epistemic uncertainties. The hazard results for generic rock condition (Vs30 = 800 m/s) are displayed for 20 sites in terms of uniform hazard spectra at two return periods (475 years and 10,000 years). The contributions of the epistemic uncertainties in the ground motion characterizations and in the seismic source characterization to the total hazard uncertainties are analyzed. Finally, we compare the results with existing models developed at national scale in the framework of the first generation of models supporting the Eurocode 8 enforcement, (MEDD 2002 and AFPS06) and at the European scale (within the SHARE project), highlighting significant discrepancies at short return periods.     

Probabilistic seismic hazard assessment of the Pyrenean region

A unified probabilistic seismic hazard assessment (PSHA) for the Pyrenean region has been performed by an international team composed of experts from Spain and France during the Interreg IIIA ISARD project. It is motivated by incoherencies between the seismic hazard zonations of the design codes of France and Spain and by the need for input data to be used to define earthquake scenarios. A great effort was invested in the homogenisation of the input data. All existing seismic data are collected in a database and lead to a unified catalogue using a local magnitude scale. PSHA has been performed using logic trees combined with Monte Carlo simulations to account for both epistemic and aleatory uncertainties. As an alternative to hazard calculation based on seismic sources zone models, a zoneless method is also used to produce a hazard map less dependant on zone boundaries. Two seismogenic source models were defined to take into account the different interpretations existing among specialists. A new regional ground-motion prediction equation based on regional data has been proposed. It was used in combination with published ground-motion prediction equations derived using European and Mediterranean data. The application of this methodology leads to the definition of seismic hazard maps for 475- and 1,975-year return periods for spectral accelerations at periods of 0 (corresponding to peak ground acceleration), 0.1, 0.3, 0.6, 1 and 2 s. Median and percentiles 15% and 85% acceleration contour lines are represented. Finally, the seismic catalogue is used to produce a map of the maximum acceleration expected for comparison with the probabilistic hazard maps. The hazard maps are produced using a grid of 0.1°. The results obtained may be useful for civil protection and risk prevention purposes in France, Spain and Andorra.     

Probabilistic seismic hazard assessment of Eastern Marmara Region

The objective of this study is to evaluate the seismic hazard in Eastern Marmara Region using an improved probabilistic seismic hazard assessment methodology. Two significant improvements over the previous seismic hazard assessment practices are accomplished in this study: advanced seismic source characterization models in terms of source geometry and recurrence relationships are developed, and improved global ground motion models (NGA-W1 models) are employed to represent the ground motion variability. Planar fault segments are defined and a composite magnitude distribution model is used for all seismic sources in the region to properly represent the characteristic behavior of the North Anatolian Fault without the need for an additional background zone. Multi-segment ruptures are considered using the rupture model proposed by the Working Group on California Earthquake Probabilities (2003). Events in the earthquake catalogue are attributed to the fault zones and scenario weights are determined by releasing the accumulated seismic energy. The uniform hazard spectra at 10 % probability of exceedance in 50 years hazard level for different soil conditions (soil and rock) are revealed for specific locations in the region (Adapazar?, Düzce, Gemlik, Izmit, Iznik and Sapanca). Hazard maps of the region for rock site conditions at the selected hazard levels are provided to allow the readers perform site-specific hazard assessment and develop site-specific design spectrum for local site conditions.     

Probabilistic seismic hazard assessment of southern part of Ghana

This paper presents a seismic hazard map for the southern part of Ghana prepared using the probabilistic approach, and seismic hazard assessment results for six cities. The seismic hazard map was prepared for 10% probability of exceedance for peak ground acceleration in 50 years. The input parameters used for the computations of hazard were obtained using data from a catalogue that was compiled and homogenised to moment magnitude (Mw). The catalogue covered a period of over a century (1615–2009). The hazard assessment is based on the Poisson model for earthquake occurrence, and hence, dependent events were identified and removed from the catalogue. The following attenuation relations were adopted and used in this study—Allen (for south and eastern Australia), Silva et al. (for Central and eastern North America), Campbell and Bozorgnia (for worldwide active-shallow-crust regions) and Chiou and Youngs (for worldwide active-shallow-crust regions). Logic-tree formalism was used to account for possible uncertainties associated with the attenuation relationships. OpenQuake software package was used for the hazard calculation. The highest level of seismic hazard is found in the Accra and Tema seismic zones, with estimated peak ground acceleration close to 0.2 g. The level of the seismic hazard in the southern part of Ghana diminishes with distance away from the Accra/Tema region to a value of 0.05 g at a distance of about 140 km.     

Probabilistic seismic hazard assessment of Switzerland: best estimates and uncertainties

We present the results of a new genera tion of probabilistic seismic hazard assessment for Switzerland. This study replaces the previous intensity-based generation of national hazard maps of 1978. Based on a revised moment-magnitude earthquake catalog for Switzerland and the surrounding regions, covering the period 1300–2003, sets of recurrence parameters (a and b values, M _max ) are estimated. Information on active faulting in Switzerland is too sparse to be used as source model. We develop instead two models of areal sources. The first oriented towards capturing historical and instrumental seismicity, the second guided largely by tectonic principles and express ing the alterative view that seismicity is less stationary and thus future activity may occur in previously quiet regions. To estimate three alterna tive a and b value sets and their relative weighting, we introduce a novel approach based on the modified Akaike information criterion, which allows us to decide when the data in a zone deserves to be fitted with a zone-specific b value. From these input parameters, we simulate synthetic earthquake catalogs of one-million-year duration down to magnitude 4.0, which also reflect the difference in depth distribution between the Alpine Foreland and the Alps. Using a specific predictive spectral ground motion model for Switzerland, we estimate expected ground motions in units of the 5% damped acceleration response spectrum at frequencies of 0.5–10 Hz for all of Switzerland, referenced to rock sites with an estimated shear wave velocity of 1,500 m/s² in the upper 30 m. The highest hazard is found in the Wallis, in the Basel region, in Graubünden and along the Alpine front, with maximum spectral accelerations at 5 Hz frequency reaching 150 cm/s² for a return period of 475 years and 720 cm/s² for 10,000 years. Electronic supplementary material The online version of this article (doi: ) contains supplementary material, which is available to authorized users.     

Probabilistic seismic hazard assessment in SE-Spain based on macroseismic site histories

In many countries such as Spain earthquake databases still mainly comprise macroseismic data from felt effects. The full exploit of this information is of basic importance for seismic risk assessment and emergency planning, given the strict link between macroseismic intensity and damage. A probabilistic procedure specifically developed to handle macroseismic data, mostly relying on site information and seismogenic-source free, has been applied to evaluate seismic hazard in SE-Spain (Alicante-Murcia region). Present seismicity is moderate-low with largest magnitudes slightly over Mw5.0. The historical record includes very destructive earthquakes, maximum EMS98 intensities reaching IX–X and X in the nineteenth century (e.g., Torrevieja 1829 earthquake). Very recently, two events in the area on 11 May 2011 (Mw4.5, Mw5.2) killed nine people, injured 300, and produced important damage in the city of Lorca. Regional hazard maps for the area together with specific hazard curves at selected localities are obtained. Results are compared with the maximum observed intensities in the period 1300–2012, and with the values in the seismic hazard map from the Spanish Building Code in force. In general, the maximum felt intensity values are closer to the hazard values calculated for 2 % probability of exceedance in 50 years, using felt and expected intensity. The intensity-based probabilistic hazard maps obtained through the applied approach reduce the inherent smoothing of those based on standard probabilistic seismic hazard assessment approaches for the region, allowing identifying possible over- or sub-estimates of site hazard values, providing very valuable information for risk reduction strategies or for future updates of the building code hazard maps.     

Probabilistic seismic hazard analysis in Nepal

The seismic ground motion hazard for Nepal has been estimated using a probabilistic approach. A catalogue of earthquakes has been compiled for Nepal and the surrounding region （latitude 26% N and 31.7% N and longitude 79° E and 90° E） from 1255 to 2011. The distribution of catalogued earthquakes, together with available geological and tectonic information were used to delineate twenty-three seismic source seismic source information and probabilistic earthquake hazard prediction relationship, peak ground accelerations （PGAs） have zones in Nepal and the surrounding region. By using the parameters in conjunction with a selected ground motion been calculated at bedrock level with 63%, 10%, and 2% probability of exceedance in 50 years. The estimated PGA values are in the range of 0.07-0.16 g, 0.21 0.62 g, and 0.38-1.1 g for 63%, 10%, and 2% probability of exceedance in 50 years, respectively. The resulting ground motion maps show different characteristics of PGA distribution, i.e., high hazard in the far-western and eastern sections, and low hazard in southern Nepal. The quantified PGA values at bedrock level provide information for microzonation studies in different parts of the country.     

Probabilistic seismic hazard analysis: Early history

Probabilistic seismic hazard analysis (PSHA) is the evaluation of annual frequencies of exceedence of ground motion levels (typically designated by peak ground acceleration or by spectral accelerations) at a site. The result of a PSHA is a seismic hazard curve (annual frequency of exceedence vs ground motion amplitude) or a uniform hazard spectrum (spectral amplitude vs structural period, for a fixed annual frequency of exceedence). Analyses of this type were first conceived in the 1960s and have become the basis for the seismic design of engineered facilities ranging from common buildings designed according to building codes to critical facilities such as nuclear power plants. This Historical Note traces the early history of PSHA. Copyright © 2007 John Wiley & Sons, Ltd.     

Probabilistic seismic loss assessment of aging bridges using a component‐level cost estimation approach

Deteriorating highway bridges in the United States and worldwide have demonstrated susceptibility to damage in earthquake events, with considerable economic consequences due to repair or replacement. Current seismic loss assessment approaches for these critical elements of the transportation network neglect the effects of aging and degradation on the loss estimate. However, the continued aging and deterioration of bridge infrastructure could not only increase susceptibility to seismic damage, but also have a significant impact on these economic losses. Furthermore, the contribution of individual aging components to system‐level losses, correlations between these components, and uncertainty modeling in the risk assessment and repair modeling are all crucial considerations to enhance the accuracy and confidence in bridge loss estimates. In this paper, a new methodology for seismic loss assessment of aging bridges is introduced based on the non‐homogeneous Poisson process. Statistical moments of seismic losses can be efficiently estimated, such as the expected value and variance. The approach is unique in its account for time‐varying seismic vulnerability, uncertainty in component repair, and the contribution of multiple correlated aging components. A representative case study is presented with two fundamentally distinct highway bridges to demonstrate the effects of corrosion deterioration of different bridge components on the seismic losses. Using the proposed model, a sensitivity study is also conducted to assess the effect of parameter variations on the expected seismic losses. The results reveal that the seismic losses estimated by explicitly considering the effects of deterioration of bridge components is significantly higher than that found by assuming time‐invariant structural reliability. Copyright © 2011 John Wiley & Sons, Ltd.     

Probabilistic sinkhole modelling for hazard assessment

A method for quantitatively assessing sinkhole susceptibility (spatial probability) and hazard (spatio‐temporal probability) has been developed and independently tested in a 50 km² sector of the Ebro Valley evaporite karst. Three genetic types of sinkholes have been mapped in the floodplain and a terrace surface: 947 small cover‐collapse sinkholes (type 1, terrace), large collapse sinkholes (type 2, floodplain) and large subsidence depressions (type 3, floodplain). The type 1 sinkhole inventory includes two temporal populations: 447 sinkholes formed before 24 November 2005, and 500 between that date and 2 November 2006. Sinkhole susceptibility models have been elaborated analysing the statistical relationships between the sinkholes of the 2005 inventory and a set of potential conditioning factors. The independent evaluation (validation) of the susceptibility models by means of several strategies (random, sequentially excluded, and temporal) has allowed us to select the most significant variables for each sinkhole type and assess quantitatively the quality of models; which are reasonable for the three sinkhole types. Validation has also provided information on the contribution of specific variables and the effect of changing their accuracy to the prediction capability of models. Susceptibility models for type 3 sinkholes have been validated satisfactorily with the 2006 sinkhole inventory (temporal validation). The best susceptibility model has been transformed into a hazard map considering the frequency of sinkholes that occurred in each susceptibility class between 2005 and 2006, as well as their average size. The susceptibility and hazard models obtained could be used as an objective basis for the application of mitigation measures, either of preventive or corrective nature. Copyright © 2008 John Wiley & Sons, Ltd.     

Probabilistic seismic hazard maps for the Japanese islands

Probabilistic seismic hazard maps are constructed by utilising a new methodology called the parametric-historic method, since it combines the best features of the ‘deductive’ ([2]) and ‘historic’ ( [4]) procedures.

The technique has been developed specifically for the estimation of seismic hazard at individual sites without the subjective judgment involved in the definition of seismic source zones, when specific active faults have not been mapped or identified, and when the causes of seismicity are not well understood. The combination of historical and instrumental data is permitted. The historical part of the catalogue contains only the strongest events, whereas the complete part can be divided into several subcatalogues, each assumed complete above a specified threshold of magnitude. Uncertainty in the determination of magnitude has also been taken into account. The maximum credible magnitude, m_max, is of paramount importance in this approach.

The seismic hazard maps are based on a long-term earthquake history (599–1997) compiled of the catalogues of Utsu (Utsu T. Catalog of large earthquakes in the region of Japan from 1885 through 1980. Bull Earthq Res Inst, Univ Tokyo, 1982;57:401–63), Usami (Usami T. Materials for comprehensive list of destructive earthquakes in Japan. Tokyo: Tokyo Press, 1996) and JMA for the Japanese islands. The analysis is based on subregions at a grid size of 0.05° along the Japanese islands, for each of which peak ground accelerations and spectral accelerations for natural frequencies of 1, 3, 5 and 10 Hz, are predicted and mapped to occur at a 10% probability in 50 years.     

Probabilistic seismic hazard analysis for spatially distributed infrastructure

Two key issues distinguish probabilistic seismic risk analysis of a lifeline or portfolio of structures from that of a single structure. Regional analysis must consider the correlation among lifeline components or structures in the portfolio, and the larger scope makes it much more computationally demanding. In this paper, we systematically identify and compare alternative methods for regional hazard analysis that can be used as the first part of a computationally efficient regional probabilistic seismic risk analysis that properly considers spatial correlation. Specifically, each method results in a set of probabilistic ground motion maps with associated hazard‐consistent annual occurrence probabilities that together represent the regional hazard. The methods are compared according to how replicable and computationally tractable they are and the extent to which the resulting maps are physically realistic, consistent with the regional hazard and regional spatial correlation, and few in number. On the basis of a conceptual comparison and an empirical comparison for Los Angeles, we recommend a combination of simulation and optimization approaches: (i) Monte Carlo simulation with importance sampling of the earthquake magnitudes to generate a set of probabilistic earthquake scenarios (defined by source and magnitude); (ii) the optimization‐based probabilistic scenario method, a mixed‐integer linear program, to reduce the size of that set; (iii) Monte Carlo simulation to generate a set of probabilistic ground motion maps, varying the number of maps sampled from each earthquake scenario so as to minimize the sampling variance; and (iv) the optimization‐based probabilistic scenario again to reduce the set of probabilistic ground motion maps. Copyright © 2012 John Wiley & Sons, Ltd.     

Updated seismic hazard assessment of Tunisia

Modern earthquake loss models make use of earthquake catalogs relevant to the seismic hazard assessment upon seismicity and seismotectonic analysis. The main objective of this paper is to investigate a recently compiled catalog (National Institute of Meteorology or INM catalog: 412-2011) and to generate seismic hazard maps through classical probabilistic seismic hazard assessment (PSHA) and smoothed-gridded seismicity models for Tunisia. It is now established with the local earthquake bulletin that the recent seismicity of Tunisia is sparse and moderate. Therefore, efforts must be undertaken to elaborate a robust hazard analysis for risk assessment and seismic design purposes. These recommendations follow the recently published reports by the World Bank that describe the seismic risk in Tunis City as being beyond a tolerable level with an MSK intensity level of VII. Some attempts were made during the past two decades to assess the seismic hazard for Tunisia and they have mostly failed to properly investigate the historical and instrumental seismicity catalog. This limitation also exists for the key aspect of epistemic and random uncertainties impact on the final seismic hazard assessment. This study also investigates new ground motion prediction equations suitable for use in Tunisia. The methodology applied herein uses, for the first time in PSHA of Tunisia, seismicity parameters integrated in logic tree framework to capture epistemic uncertainties through three different seismic source models. It also makes use of the recently released version of OpenQuake engine; an open-source tool for seismic hazard and risk assessment developed in the framework of the Global Earthquake Model.     

Probabilistic earthquake hazard assessment for Peninsular India

In this paper, a new probabilistic seismic hazard assessment (PSHA) is presented for Peninsular India. The PSHA has been performed using three different recurrence models: a classical seismic zonation model, a fault model, and a grid model. The development of a grid model based on a non-parameterized recurrence model using an adaptation of the Kernel-based method that has not been applied to this region before. The results obtained from the three models have been combined in a logic tree structure in order to investigate the impact of different weights of the models. Three suitable attenuation relations have been considered in terms of spectral acceleration for the stable continental crust as well as for the active crust within the Gujarat region. While Peninsular India has experienced large earthquakes, e.g., Latur and Jabalpur, it represents in general a stable continental region with little earthquake activity, as also confirmed in our hazard results. On the other hand, our study demonstrates that both the Gujarat and the Koyna regions are exposed to a high seismic hazard. The peak ground acceleration for 10 % exceedance in 50 years observed in Koyna is 0.4 g and in the Kutch region of Gujarat up to 0.3 g. With respect to spectral acceleration at 1 Hz, estimated ground motion amplitudes are higher in Gujarat than in the Koyna region due to the higher frequency of occurrence of larger earthquakes. We discuss the higher PGA levels for Koyna compared Gujarat and do not accept them uncritically.     

Regional and local seismic hazard assessment

Recent earthquakes such as the M_JMA 7.2 Hyogo-ken Nambu earthquake and the M 7.4 Kocaeli earthquake demonstrate once again the need to include detailed soil investigation into hazard evaluation, that is the need of microzonation. Seismic hazard assessment evaluated at a regional scale generally does not consider soil effects but only in a limited way using an attenuation law that can be ‘soft soil’ or ‘rock’. However, the relevant role of seismic hazard in the assessment of seismic coefficients for the definition of the actions in seismic codes must be properly considered. That is to say, the level of protection of buildings is proportional to a definite level of hazard (generally considered to be the ground motion with 10% probability of exceedence in 50 years). When a microzonation is performed, this criterion cannot be ignored, therefore, a clear linkage must be established between hazard (regional scale) and microzonation. The crucial point is represented by the reference motion (or input motion) to be used for site effects analysis, that must be compatible with the regional seismic hazard. In this paper, three different approaches for reference motion evaluation are analysed: probabilistic; stochastic; and deterministic. Through the case history of Fabriano microzonation the three approaches are compared. It is shown that each approach presents advantages and disadvantages with respect to the others. For example, the probabilistic approach (the reference motion is directly derived from the expected response spectra for a given return period) is linked with hazard, but produces an overestimation in short periods range, while the deterministic approach correctly simulates the wave propagation, but it ends with a kind of conditional probability. Until now, clear criteria to choose the right approach do not appear to exist and the expert experience is of fundamental importance.     

山东某场地概率地震危险性分析

利用概率地震危险性分析(CPSHA)方法,对山东某场地进行地震危险性分析,通过对该场地划分潜在震源区,确定地震活动性参数及地震动衰减关系,计算分析地震危险性概率,基本确定对该场地地震动峰值加速度起主要贡献的几个潜在震源区及贡献值,并确定该场地50年超越概率10%的水平向基岩地震动加速度峰值。结果发现,CPSHA方法以具体的构造尺度和更加细致的构造标志来划分潜在震源区,使潜在震源区规模缩减,从而更能反映地震活动在空间分布上的不均匀性。     

Probabilistic seismic hazard assessment for the two layer fault system of Antalya (SW Turkey) area

Southwest Turkey, along Mediterranean coast, is prone to large earthquakes resulting from subduction of the African plate under the Eurasian plate and shallow crustal faults. Maximum observed magnitude of subduction earthquakes is Mw = 6.5 whereas that of crustal earthquakes is Mw = 6.6. Crustal earthquakes are sourced from faults which are related with Isparta Angle and Cyprus Arc tectonic structures. The primary goal of this study is to assess seismic hazard for Antalya area (SW Turkey) using a probabilistic approach. A new earthquake catalog for Antalya area, with unified moment magnitude scale, was prepared in the scope of the study. Seismicity of the area has been evaluated by the Gutenberg-Richter recurrence relationship. For hazard computation, CRISIS2007 software was used following the standard Cornell-McGuire methodology. Attenuation model developed by Youngs et al. Seismol Res Lett 68(1):58–73, (1997) was used for deep subduction earthquakes and Chiou and Youngs Earthq Spectra 24(1):173–215, (2008) model was used for shallow crustal earthquakes. A seismic hazard map was developed for peak ground acceleration and for rock ground with a hazard level of a 10% probability of exceedance in 50 years. Results of the study show that peak ground acceleration values on bedrock change between 0.215 and 0.23 g in the center of Antalya.     

Probabilistic seismic loss estimation via endurance time method

Probabilistic Seismic Loss Estimation is a methodology used as a quantitative and explicit expression of the performance of buildings using terms that address the interests of both owners and insurance companies. Applying the ATC 58 approach for seismic loss assessment of buildings requires using Incremental Dynamic Analysis (IDA), which needs hundreds of time-consuming analyses, which in turn hinders its wide application. The Endurance Time Method (ETM) is proposed herein as part of a demand propagation prediction procedure and is shown to be an economical alternative to IDA. Various scenarios were considered to achieve this purpose and their appropriateness has been evaluated using statistical methods. The most precise and efficient scenario was validated through comparison against IDA driven response predictions of 34 code conforming benchmark structures and was proven to be sufficiently precise while offering a great deal of efficiency. The loss values were estimated by replacing IDA with the proposed ETM-based procedure in the ATC 58 procedure and it was found that these values suffer from varying inaccuracies, which were attributed to the discretized nature of damage and loss prediction functions provided by ATC 58.     

Probabilistic seismic hazard analysis for the city of Quetta,Pakistan

Seismic hazard assessment for Quetta is carried out using probabilistic seismic hazard analysis technique based on area sources and augmented by line source used for the first time in Pakistan. Seismic data has been collected and analyzed in spatial and temporal domains. Five Seismic Zones have been modeled in line with tectonics of the region with b-value of 1.14 using regression. The b-value is slightly higher, which is attributed to the fact that aftershocks were not removed as it distorted the dataset. Five fault sources are modeled, with three as reverse and two as strike-slip with 7.8 as maximum magnitude. Mach Structure is included in the tectonics for the first time. The attenuation relation used in the present study is recommended by various researchers. The expected Peak Ground Acceleration for 500-year return period is 4.79 m/s² for rock outcrop and characterized as very high. Furthermore, variation in spectral acceleration within Quetta city is observed, for which spectral curves are developed for four different places.