不同支撑形式高强钢组合偏心支撑抗震性能研究

耗能梁段作为偏心支撑结构的耗能元件,在大震作用下通过弹塑性变形吸收地震能量,保护主体结构处于弹性受力状态。现行规范基于强度的设计理论,为了保证耗能梁段进入塑性或破坏,梁柱构件需要进行放大内力设计,导致截面过大,而且基于强度的设计方法很难保证结构的整体破坏状态。目前,抗震设计越来越重视基于性能的设计思想,该方法能够评估结构的弹塑性反应。对于高强钢组合偏心支撑,其中耗能梁段和支撑采用Q345钢,框架梁柱采用Q460或者Q690高强度钢材,高强钢不仅带来良好的经济效益,而且能够推广高强钢在抗震设防区的应用。利用基于性能设计方法设计了4种不同形式的高强钢组合偏心支撑钢框架,包括K形、Y形、V形和D形,考虑4层、8层、12层和16层的影响。通过Pushover分析和非线性时程分析评估该结构的抗震性能,研究结果表明:4种形式的高强钢组合偏心支撑钢框架具有类似的抗震性能,在罕遇地震作用下,几乎所有耗能梁段均参与耗能,而且层间侧移与耗能梁段转角沿高度分布较为均匀。其中:D形偏心支撑具有最大的抗侧刚度,但延性较差,而Y形偏心支撑的抗侧刚度最弱,但延性最佳。     

基于Revit平台设计建筑模型的钢网架结构抗震性能数值模拟

研究基于Revit平台设计建筑模型的钢网架结构抗震性能数值模拟方法,对于提高钢网架结构抗震性能以及安全性具有重要应用价值。该方法依据标高和轴网的定位信息设计钢网架建筑构件及结构构件后,通过Revit软件平台确定实例钢网架结构建筑模型大体框架;采用绑定约束以及接触约束方法,分别实现建筑模型杆件-梁以及混凝土-型钢间的约束,并采用位移控制加载方法在得到的建筑模型杆顶以及梁与轴线方向加载轴向荷载和往复荷载。采用TurnTool虚拟仿真软件,进行钢网架结构抗震性数值模拟。结果显示:在低周往复荷载作用下钢网架结构荷载与位移的变化较为稳定;在低周往复荷载作用下的塑性阶段时,结构的纵向系杆对混凝土存在约束效果,构件间距越小该结构的延性就越好,纵向系杆能够提高实例钢网架结构的受力性;不同地震波作用下钢网架结构楼层节点位移随着楼层的增高而加大,证明了所设计模型的抗震模拟结果准确性较高。     

Probabilistic seismic assessment of multistory precast concrete frames exposed to corrosion

Seismic design of concrete structures is currently based on time-invariant capacity design criteria which do not account for environmental hazards. The significant progressive decay of strength and ductility of concrete structures exposed to damage, in particular due to reinforcing steel corrosion, shows that this approach should be revised to consider the deterioration over time of the seismic performance. This is important also for precast systems, for which most of structural members are often directly exposed to the atmosphere and environmental aggressiveness. This paper presents a probabilistic approach for the lifetime assessment of seismic performance of concrete structures considering the interaction of seismic and environmental hazards. The effectiveness of the proposed approach is shown by its application to multistory precast buildings exposed to corrosion. The results show that structures designed for the same seismic action could have different lifetime seismic performance depending on the environmental exposure. These results emphasize the importance of a life-cycle approach to both seismic assessment of existing buildings and seismic design of new structures, and indicate that capacity design criteria need to be properly revised to consider the severity of the environmental exposure.     

基于时变地震损伤模型的多龄期钢框架结构易损性分析

基于时变地震损伤模型提出酸性大气环境作用下多龄期钢框架结构概率地震易损性分析的方法及步骤;考虑服役龄期对钢框架结构抗震性能的影响,分别建立时变概率地震需求模型、时变概率抗震能力模型及时变易损性模型;在概率地震需求分析及概率抗震能力分析的基础上,得到多龄期(20年、30年、40年、50年)钢框架结构的易损性模型及易损性曲线。     

大跨度钢管混凝土拱桥抗震性能指标研究

高轴压比钢管混凝土墩柱的试验结果对钢管混凝土拱肋具有较大的借鉴意义。为明确大跨度钢管混凝土拱桥的抗震性能指标,研究了高轴比钢管混凝土构件的破坏过程及延性性能。以弯矩作为性能指标将高轴压比钢管混凝土构件的试验破坏过程分为轻微损伤、有限损伤与严重损伤3个阶段,结合钢管混凝土截面性能状态的数值分析,探讨了高轴压比钢管混凝土构件的破坏机理。结果表明:高轴压比钢管混凝土构件具有一定的可用延性;提出了以计算等效屈服弯矩作为抗震性能指标,适当利用延性和实现钢管混凝土拱桥的有限损伤抗震设计,并给出了与有限损伤相关的截面性能状态及参数。研究成果弥补了规范在此方面的不足,可供高烈度地震区大跨度钢管混凝土拱桥抗震设计时参考。     

多龄期钢框架时变损伤模型研究

对3种不同厚度的钢材标准试件进行酸性大气环境气雾加速腐蚀试验,并对锈蚀后的试件进行单向拉伸试验,得到钢材力学性能随失重率的衰变规律。同时考虑构件截面削弱与材料力学性能降低,建立不同锈蚀程度下的钢框架有限元分析模型,利用非线性静力推覆分析得到锈蚀钢框架结构的整体初始刚度随锈蚀程度增大的退化规律,以表征结构因锈蚀造成的损伤。提出同时反映最大变形效应和累积耗能效应的双参数结构整体地震损伤模型,并在此损伤模型的基础上集合钢材材性试验结果及有限元分析结果,提出适用于锈蚀钢结构的"时变"损伤模型。对比分析以层间位移角及时变损伤模型为性能指标建立的不同龄期钢框架结构的地震易损性曲线,结果表明:随着锈蚀程度的增加,在相同地震动强度下结构超越某一极限状态的失效概率均增大。     

钢框架结构的地震损伤研究

基于预定损伤法对钢框架构件主要设计参数进行损伤敏感度分析,研究主要设计参数与钢框架结构梁、柱损伤的关系;揭示钢框架结构梁、柱的损伤及梁、柱线刚度比、结构高宽比、柱轴压比、锈蚀率对楼层损伤的影响规律;获得楼层的损伤与整体结构损伤的关系,最终建立钢框架结构的损伤演化模型。研究成果可为建立地震激励下钢框架结构的损伤模型提供理论基础和数据支持。     

Building damage from the Marmara, Turkey earthquake of August 17, 1999

The objective of this paper is to provide a brief overview of damage as observed immediately following the earthquake. Detailed studies of structural seismic performance, conducted in the time elapsed since August 1999, are not the subject of this paper, but rather the object of other papers presented in this Special Issue of the Journal. Damage to reinforced concrete, masonry, and steel structures, is described. The mode the failure presented include: foundation failures; soft stories; strong beams and weak columns; lack of column confinement and poor detailing practice; buckling and fractures of steel members; and non-structural damage. Some general lessons learned from this earthquake are also formulated.     

装配式钢混组合结构加固时抗震性能模糊综合评估模型研究

参数化的装配式钢混组合结构建筑信息模型缺少结构信息描述,无法实现装配式钢混组合结构图档的修正和自主更新,对结构构件的损伤评估效果差,抗震加固性能差。据此提出用于装配式钢混组合结构抗震加固的建筑信息模型,模型框架包括建筑设计模型、结构设计模型、结构抗震加固设计和损伤评估;通过结构构件的实体定义、属性定义和关联性定义,全面描述柱、梁、板和墙等钢混组合结构构件的抗震加固性能信息;采用模糊加固评估方法获取精准的结构构建综合损伤指数,评估结构构件的加固等级,提高抗震加固性能。经实验证明,所设计模型得到的结构损伤指数与实际损伤指数的误差低于0.03,说明该模型分析装配式钢混组合结构抗震加固性能准确性较高。     

拱形与矩形断面地铁车站结构地震反应比较研究

采用动力时程法开展了拱形与矩形断面地铁车站结构地震反应的研究,分析了拱形断面和矩形断面地铁车站结构的关键截面在地震作用下的内力及变形的差异。结果表明:相比于矩形断面车站结构,拱形断面车站结构顶板边缘处和侧墙顶端的弯矩明显减小,车站侧墙顶端和顶板边缘处因承受弯矩过大而发生破坏的可能降低;内柱截面的轴压比明显减小,且与侧墙的轴压比差异显著减小,受力分配更为合理;拱形车站结构顶、底板的相对位移、内柱和侧墙的位移角相对较小。在已模拟的工况下拱形车站内力分布形式更为合理,水平变形相对较小,更有利于抗震。     

Pure aluminium shear panels as dissipative devices in moment‐resisting steel frames

The use of energy dissipation systems for the seismic control of steel structures represents a valid alternative to conventional seismic design methods. The seismic devices currently employed are mostly based on the metallic yielding technology due to the large feasibility and efficiency they can provide. Within this context, in the current paper an innovative solution based on the adoption of low‐yield‐strength pure aluminium shear panels (SPs) for seismic protection of steel moment‐resisting frames is proposed and investigated. In order to prove the effectiveness of the system, a wide numerical study based on both static and dynamic non‐linear analyses has been carried out, considering a number of different frame‐to‐shear panel combinations, aiming at assessing the effect of the main influential parameters on the seismic response of the structure. The obtained results show that the contribution provided by aluminium SPs is rather significant, allowing a remarkable improvement of the seismic performance of the structure in terms of stiffness, strength and ductility, with the possibility to strongly limit the damage occurring in the members of moment‐resisting frames. In particular, it is clearly emphasized that the stiffening effect provided by SPs allows a more rational design procedure to be adopted, since the serviceability limit state check does not lead to unavoidable and uneconomical increase of the size of main structural members. Copyright © 2007 John Wiley & Sons, Ltd.     

Markovian modeling of seismic damage accumulation

Analysis of civil structures at the scale of life‐cycle requires stochastic modeling of degradation. Phenomena causing structures to degrade are typically categorized as aging and point‐in‐time overloads. Earthquake effects are the members of the latter category this study deals with in the framework of performance‐based earthquake engineering (PBEE). The focus is structural seismic reliability, which requires modeling of the stochastic process describing damage progression, because of subsequent events, over time. The presented study explicitly addresses this issue via a Markov‐chain‐based approach, which is able to account for the change in seismic response of damaged structures (i.e. state‐dependent seismic fragility) as well as uncertainty in occurrence and intensity of earthquakes (i.e. seismic hazard). The state‐dependent vulnerability issue arises when the seismic hysteretic response is evolutionary and/or when the damage measure employed is such that the degradation increment probabilistically depends on the conditions of the structure at the time of the shock. The framework set up takes advantage also of the hypotheses of classical probabilistic seismic hazard analysis, allowing to separate the modeling of the process of occurrence of seismic shocks and the effect they produce on the structure. It is also discussed how the reliability assessment, which is in closed‐form, may be virtually extended to describe a generic age‐ and state‐dependent degradation process (e.g. including aging and/or when aftershock risk is of interest). Illustrative applications show the options to calibrate the model and its potential in the context of PBEE. Copyright © 2015 John Wiley & Sons, Ltd.     

Traveling wave effect on the seismic response of a steel arch bridge subjected to near fault ground motions

In the 1990s, several major earthquakes occurred throughout the world, with a common observation that near fault ground motion (NFGM) characteristics had a distinct impact on causing damage to civil engineering structures that could not be predicted by using far field ground motions. Since then, seismic responses of structures under NFGMs have been extensively examined, with most of the studies focusing on structures with relatively short fundamental periods, where the traveling wave effect does not need to be considered. However, for long span bridges, especially arch bridges, the traveling wave (only time delay considered) effect may be very distinct and is therefore important. In this paper, the results from a case study on the seismic response of a steel arch bridge under selected NFGMs is presented by considering the traveling wave effect with variable apparent velocities. The effects of fling step and long period pulses of NFGMs on the seismic responses of the arch bridge are also discussed.     

Seismic response of steel frame structures with hybrid passive control systems

The concept of the hybrid passive control system is studied analytically by investigating the seismic response of steel frame structures. Hybrid control systems consist of two different passive elements combined into a single device or system. The hybrid systems investigated in this research consist of a rate‐dependent damping device paired with a rate‐independent energy dissipation element. The innovative configurations exploit individual element strengths and offset their weaknesses through multiphased behavior. A nine‐story, five‐bay steel moment‐frame was used for the analysis. Six different seismic resisting systems were analyzed and compared. The conventional systems included a special moment‐resisting frame (SMRF) and a dual SMRF–buckling‐restrained brace (BRB) system. The final four configurations are hybrid passive systems. The different hybrid configurations utilize a BRB and either a high‐damping rubber damper or viscous fluid damper. The analyses were run in the form of an incremental dynamic analysis. Several damage measures were calculated, including maximum roof drift, base shear, and total roof acceleration. The results demonstrate the capability of hybrid passive control systems to improve structural response compared with conventional lateral systems and to be effective for performance‐based seismic design. Each hybrid configuration improved some aspect of structural response with some providing benefits for multiple damage measures. The multiphased nature provides improved response for frequent and severe seismic events. Copyright © 2011 John Wiley & Sons, Ltd.     

网架减震球型钢支座减震性能振动台试验研究

针对网架结构的受力特点,提出了一种新型网架减震球型钢支座.按照相似原理制作了网架减震球型钢支座的缩尺模型,并通过模拟地震振动台试验系统地研究了这种支座在地震作用下的减隔震性能.试验结果表明,网架减震球型钢支座能够有效阻隔地震动向上部结构的传递,滞回环饱满、等效阻尼比大,具有良好的隔震及减震耗能能力.     

On the design and seismic response of RC frame buildings designed with Eurocode 8

Performance-Based Seismic Design is now widely recognized as the pre-eminent seismic design and assessment methodology for building structures. In recognition of this, seismic codes may require that buildings achieve multiple performance objectives such as withstanding moderate, yet frequently occurring earthquakes with minimal structural and non-structural damage, while withstanding severe, but rare earthquakes without collapse and loss of life. These objectives are presumed to be satisfied by some codes if the force-based design procedures are followed. This paper investigates the efficacy of the Eurocode 8 force-based design provisions with respect to RC frame building design and expected seismic performance. Four, eight, and 16-storey moment frame buildings were designed and analyzed using the code modal response spectrum analysis provisions. Non-linear time-history analyses were subsequently performed to determine the simulated seismic response of the structures and to validate the Eurocode 8 force-based designs. The results indicate the design of flexural members in medium-to-long period structures is not significantly influenced by the choice of effective member stiffness; however, calculated interstorey drift demands are significantly affected. This finding was primarily attributed to the code’s enforcement of a minimum spectral ordinate on the design spectrum. Furthermore, design storey forces and interstorey drift demand estimates (and therefore damage), obtained by application of the code force-based design procedure varied substantially from those found through non-linear time-history analysis. Overall, the results suggest that though the Eurocode 8 may yield life-safe designs, the seismic performance of frame buildings of the same type and ductility class can be highly non-uniform.     

关于钢结构抗震存在的问题及建议

本文探讨了目前钢结构抗震设计中存在的两个主要问题:其一是钢结构的地震作用,由于多高层钢结构房屋被列入“建筑抗震设计规范”(GB50011-2001)中时没有考虑钢结构延性好和弹性阶段阻尼比较小的特点,使得钢结构地震作用偏大,用钢量偏高;其二是钢结构承载力抗震调整系数对梁和焊缝的规定与焊缝强度高于母材强度的实际情况不符,造成设计困难。本文对现行抗震规范、“建筑工程抗震性态设计通则”和美国UBC规范的地震作用进行了分析比较,提出按照耗能能力将钢结构体系分为四类,在此基础上引入结构体系调整系数,对每类结构的地震作用取值给出建议。针对梁柱刚性连接,从抗震设计原则出发,对7、8和9度区分别建议了适合采用的连接形式,并给出了小震和大震下的设计验算公式。     

SRC框支剪力墙结构地震反应简化分析模型研究

针对钢筋混凝土高层框支剪力墙结构抗震性能差的缺点,提出采用型钢混凝土（SRC）梁柱框支剪力墙,试验结果表明了其良好的抗震性能。提出了框支剪力墙结构地震反应简化分析模型,将结构简化为由墙单元和框支单元组成的弹簧体系,墙单元采用二元件模型。推导了框支单元刚度矩阵,基于理论公式和试验结果给出了框支单元恢复力模型。根据提出的简化模型,编制了结构地震反应时程分析程序。程序计算结果与ETABS分析结果及振动台试验结果吻合较好,为进一步对SRC框支剪力墙结构进行地震反应分析提供了理论基础。     

Seismic responses of postyield hardening single–degree-of-freedom systems incorporating high-strength elastic material

It is widely accepted that ductility design improves the seismic capacity of structures worldwide. Nevertheless, inelastic deformation allows serious damage to occur in structures. Previous studies have shown that a certain level of postyield stiffness may reduce both the peak displacement and residual deformation of a structure. In recent years, several high-strength elastic materials, such as fiber-reinforced polymer (FRP) and high-strength steel bars, have been developed. Application of these materials can easily provide a structure with a much higher and more stable postyield stiffness. Many materials, members, and structures that incorporate both high-strength elastic materials and conventional materials show significant postyield hardening (PYH) behaviors. The significant postyield stiffness of PYH structures can help effectively reduce both peak and residual deformations, providing a choice when designing resilient structures. However, the findings of previous studies of structures with elastic-perfectly plastic (EPP) behavior or small postyield stiffness may not be accurate for PYH structures. The postyield stiffness of a structure must be considered an important primary structural parameter, in addition to initial stiffness, yielding strength, and ductility. In this paper, extensive time history and statistical analyses are carried out for PYH single–degree-of-freedom (SDOF) systems. The mean values and coefficients of variation of the peak displacement and residual deformation are obtained and discussed. A new R-μ_p-T-α relationship and damage index for PYH structures are proposed. A theoretical model for the calculation of residual deformation is also established. These models provide a basis for developing the appropriate seismic design and performance evaluation procedures for PYH structures.     

城市群体建筑物震害模拟方法研究

本文针对目前进行城市群体建筑物震害预测时,在数据收集和计算工作中遇到的实际困难,提出了一种简化的震害计算方法——单元破坏度指数法。同时将该计算模型嵌入到ArcView 9.0的GIS平台中,并以Oracle数据库为支撑,结合青岛市的实际数据,对城市群体建筑物的震害进行了模拟。结果表明,单元破坏度指数法不仅大大简化了数据收集和处理的工作量,而且计算结果的精度同样能满足工程应用的要求,与GIS相结合可以客观快速地模拟出城市群体建筑物的震害程度及其空间分布。