The impact of diagenetic fluid–rock reactions on Rotliegend sandstone composition and petrophysical properties (Altmark area, central Germany)

In the framework of the German R&D joint project CLEAN (CO₂ large-scale enhanced gas recovery in the Altmark natural gas field), Rotliegend reservoir sandstones of the Altensalzwedel block in the Altmark area (Saxony-Anhalt, central Germany) have been studied to characterise litho- and diagenetic facies, mineral content, geochemical composition, and petrophysical properties. These sands have been deposited in a playa environment dominated by aeolian dunes, dry to wet sand flats and fluvial channel fills. The sediments exhibit distinct mineralogical, geochemical, and petrophysical features related to litho- and diagenetic facies types. In sandstones of the damp to wet sandflats, their pristine red colours are preserved and porosity and permeability are only low. Rocks of the aeolian environment and most of the channel fill deposits are preferentially bleached and exhibit moderate to high porosity and permeability. Although geochemical element whole rock content in these rocks is very similar, element correlations are different. Variations in porosity and permeability are mainly due to calcite and anhydrite dissolution and differences in clay coatings with Fe-bearing illitic-chloritic composition exposed to the pore space. Moreover, mineral dissolution patterns as well as compositions (of clays and carbonate) and morphotypes of authigenic minerals (chlorite, illite) are different in red and bleached rocks. Comparison of the geochemical composition and mineralogical features of diagenetically altered sandstones and samples exposed to CO₂-bearing fluids in laboratory batch experiments exhibit similar character. Experiments prove an increase in wettability and water binding capacity during CO₂ impact.     

CLEAN: project overview on CO2 large-scale enhanced gas recovery in the Altmark natural gas field (Germany)

The joint research project CLEAN was conducted in the years 2008?C2011 by a German research and development (R&D) alliance of 16 partners from science and industry. The project was set-up as pilot project to investigate the processes relevant to enhanced gas recovery (EGR) by the injection of CO₂ into a subfield of the almost depleted Altmark natural gas field. Despite the setback that permission for active injection was not issued by the mining authority during the period of the project, important results fostering the understanding of processes linked with EGR were achieved. Work carried out led to a comprehensive evaluation of the EGR potential of the Altmark field and the Altensalzwedel subfield in particular. The calculated safety margins emphasize that technical well integrity of the 12 examined boreholes is given for EGR without a need for any further intervention. The laboratory and field tests confirm that the Altensalzwedel subfield is suitable for the injection of 100,000?t of CO₂. Numerical simulations provide sound predictions for the efficiency and safety of the EGR technology based on the CO₂ injection. The development and testing of different monitoring techniques facilitate an improved surveying of CO₂ storage sites in general. The CLEAN results provide the technological, logistic and conceptual prerequisites for implementing a CO₂-based EGR project in the Altmark and provide a benchmark for similar projects in the world.     

Analyses of pre-injection reservoir data for stable carbon isotope trend predictions in CO2 monitoring: preparing for CO2 injection

Baseline monitoring at the proposed enhanced gas recovery site in Altmark (Germany) was carried out in combination with theoretical and laboratory investigations to describe and predict the principles of expected stable carbon isotope and dissolved inorganic carbon (DIC) trends during CO₂ injection in reservoirs. This provides fundamental data for site-specific characterisation for monitoring purposes. Baseline ??¹³C values at the Altmark site ranged between ?1.8 and ?11.5??? and DIC values were about 2?mmol?L^?1. These baseline values form the basis for a theoretical study on the influences of the ambient reservoir conditions on the state of geochemical and isotope equilibrium of the reservoir fluids. Transferring this theoretical study to the Altmark site enables predictions on geochemical trends during potential injection. Assuming that CO₂ would be injected at the Altmark site to pCO₂?=?100?bar and with a ??¹³C of ?30???, at isotopic and geochemical equilibrium, ??¹³C_DIC values would approach this end-member, and DIC concentrations of 1,000?mmol L^?1 would be expected. Laboratory experiments were conducted at low pCO₂ levels (4?C35?bars) to mimic the approach of a CO₂ plume at a monitoring well. These results support field investigations from other sites: that ??¹³C_DIC is a sensitive tool for monitoring CO₂ migration in the subsurface and simultaneously allows quantification of geochemical trapping of CO₂.     

Numerical simulation of carbon dioxide injection for enhanced gas recovery (CO2-EGR) in Altmark natural gas field

This paper studied the CO₂-EGR in Altmark natural gas field with numerical simulations. The hydro-mechanical coupled simulations were run using a linked simulator TOUGH2MP-FLAC3D. In order to consider the gas mixing process, EOS7C was implemented in TOUGH2MP. A multi-layered 3D model (4.4 km × 2 km × 1 km) which consists of the whole reservoir, caprock and base rock was generated based on a history-matched PETREL model, originally built by GDF SUEZ E&P Deutschland GmbH for Altmark natural gas field. The model is heterogeneous and discretized into 26,015 grid blocks. In the simulation, 100,000 t CO₂ was injected in the reservoir through well S13 within 2 years, while gas was produced from the well S14. Some sensitivity analyses were also carried out. Simulation results show that CO₂ tends to migrate toward the production well S14 along a NW–SE fault. It reached the observation wells S1 and S16 after 2 years, but no breakthrough occurred in the production well. After 2 years of CO₂ injection, the reservoir pressure increased by 2.5 bar, which is beneficial for gas recovery. The largest uplift (1 mm) occurred at the bottom of the caprock. The deformation was small (elastic) and caprock integrity was not affected. With the injection rate doubled the average pressure increased by 5.3 bar. Even then the CO₂ did not reach the production well S14 after 2 years of injection. It could be concluded that the previous flow field was established during the primary gas production history. This former flow field, including CO₂ injection/CH₄ production rate during CO₂-EGR and fault directions and intensity are the most important factors affecting the CO₂ transport.     

Influence of sedimentary facies on reservoir quality and distribution of diagenetic features in the Funing Formation,Wanglongzhuang Oilfield,Subei Basin,Eastern China

The Paleogene clastic sediments of the Funing Formation, which is characterized by slump-fan, delta-front, and beach-bar deposits, are important targets for oil and gas exploration in the Wanglongzhuang Oilfield, Subei Basin, eastern China. Three categories of reservoir quality are distinguished on the basis of petrographic and petrophysical experiments such as nuclear magnetic resonance (NMR) and mercury injection (MI). A paragenetic sequence for diagenetic evolution of each sedimentary facies has been reconstructed to determine the mechanisms for the variations in reservoir quality of the formation and the influence of the sedimentary facies on the distribution of diagenetic features in each of its members. The maturity of the organic material, textural relationships, and the distribution pattern of diagenetic minerals suggest that the study area underwent mainly mesodiagenesis. The mesodiagenesis A and mesodiagenesis B stages induced different diagenetic features in the target reservoir; the beach-bar sand of the E₁f₂ unit and the delta-front sand of the E₁f₄ unit underwent mostly only cementation; the delta-front deposits of the E₁f₃ unit, however, suffered more from mechanical and chemical compaction than from cementation. The loss of porosity in the fluxoturbidites of E₁f₄ due to compaction was just as large as the loss by cementation. The gravity-flow channel, sand-bar, and distributary-channel deposits have a higher porosity and permeability than the sand-beach and estuarine-bar deposits.     

Sensitivity study of pulsed neutron-gamma saturation monitoring at the Altmark site in the context of CO2 storage

The injection of CO₂ into depleted natural gas reservoirs has been proposed as a promising new technology for combining enhanced gas recovery and geological storage of CO₂. During the injection, application of suitable techniques for monitoring of the induced changes in the subsurface is required. Observing the movement and the changes in saturation of the fluids contained in the reservoir and the confining strata is among the primary aims here. It is shown that under conditions similar to the Altmark site, Germany, pulsed neutron-gamma logging can be applied with limitations. The pulsed neutron-gamma method can be applied for detection and quantification of changes in brine saturation and water content, whereas changes in the gas composition are below the detection limit. A method to account for the effects of salt precipitation resulting from evaporation of residual brine is presented.     

Chemical changes in fluid composition due to CO2 injection in the Altmark gas field: preliminary results from batch experiments

Dissolution?Cprecipitation phenomena induced by CO₂ injection to Altmark Permian sandstone were observed through laboratory experiments carried out under simulated reservoir conditions (125?°C and 50 bars of pressure). The rock sample was collected from the Altmark gas reservoir, which is being considered for enhanced gas recovery. Two sets of experiments were performed with pulverized rock samples in a closed batch reactor with either pure water (run 1) or 3?M aqueous NaCl solution (run 2) and reacted with injected CO₂ for 3, 5, and 9?days. The liquid samples were analyzed by inductively coupled plasma optical emission spectroscopy and total reflection X-ray fluorescence, where the latter proved to be a feasible alternative to conventional analytical techniques, especially since only small sample volumes (about 10???l) are needed. Chemical analysis for both fluids (water and NaCl brine) indicated a significant dissolution of calcite and anhydrite in the solution, which might be a crucial process during CO₂ injection. The brine solution enhanced the dissolution of calcite and anhydrite compared to pure water at the beginning of the reaction. Moreover, the progressive higher Si⁴⁺/Al³⁺ molar ratios (in average by a factor of 3) in the brine experiments indicated quartz dissolution. Thermodynamic calculations of mineral saturation indices highlighted the dissolution of the Ca-bearing minerals, which was in agreement with experimental results. Modeling enabled an evaluation of the dissolution processes of minerals in a low-salinity region, yet hindrances to model more saline conditions emphasize the need for further laboratory studies in order to parameterize models for deep aquifer conditions.     

Effect of injected CO2 on geochemical alteration of the Altmark gas reservoir in Germany

Capturing CO₂ from point sources and storing it in geologic formations is a potential option for allaying the CO₂ level in the atmosphere. In order to evaluate the effect of geological storage of CO₂ on rock-water interaction, batch experiments were performed on sandstone samples taken from the Altmark reservoir, Germany, under in situ conditions of 125 °C and 50 bar CO₂ partial pressure. Two sets of experiments were performed on pulverized sample material placed inside a closed batch reactor in (a) CO₂ saturated and (b) CO₂ free environment for 5, 9 and 14 days. A 3M NaCl brine was used in both cases to mimic the reservoir formation water. For the “CO₂ free” environment, Ar was used as a pressure medium. The sandstone was mainly composed of quartz, feldspars, anhydrite, calcite, illite and chlorite minerals. Chemical analyses of the liquid phase suggested dissolution of both calcite and anhydrite in both cases. However, dissolution of calcite was more pronounced in the presence of CO₂. In addition, the presence of CO₂ enhanced dissolution of feldspar minerals. Solid phase analysis by X-ray diffraction and Mössbauer spectroscopy did not show any secondary mineral precipitation. Moreover, Mössbauer analysis did not show any evidence of significant changes in redox conditions. Calculations of total dissolved solids’ concentrations indicated that the extent of mineral dissolution was enhanced by a factor of approximately 1.5 during the injection of CO₂, which might improve the injectivity and storage capacity of the targeted reservoir. The experimental data provide a basis for numerical simulations to evaluate the effect of injected CO₂ on long-term geochemical alteration at reservoir scale.     

基于岩石物理相的砂砾岩储层分类评价--以准噶尔盆地玛131井区块百二段为例

勘探实践表明,准噶尔盆地玛北斜坡主力油层段百二段砂砾岩储层非均质性强,孔隙结构差异大,需要综合影响储层的各种地质因素对其进行分类评价。利用岩芯、薄片、钻测井、物性、工业CT等资料,对准噶尔盆地玛北斜坡玛131井区块百二段砂砾岩储层沉积相、成岩相、裂缝相特征进行了研究,在此基础上分析了百二段储层岩石物理相,并基于岩石物理相对储层进行分类评价,预测有利储层发育区。通过沉积微相、成岩相的叠加聚类,对研究区百二段砂砾岩储层岩石物理相进行分类,划分出水下分流河道-不稳定组分溶蚀等岩石物理相;按照沉积相、成岩相对储层孔隙结构的建设与破坏作用归纳出3大类岩石物理相。依据三类岩石物理相将储层划分为3类,并结合压汞、薄片、CT、产能等资料进行表征与评价,其中一类和二类岩石物理相储集性能较好,三类岩石物理相为致密遮挡层。最后以亚段为单位,对百二段岩石物理相进行平面成图,预测有利储层分布区。     

Geochemistry of shallow aquifers and soil gas surveys in a feasibility study at the Rivara natural gas storage site (Po Plain,Northern Italy)

A geochemical survey, in shallow aquifers and soils, has been carried out to evaluate the feasibility of natural gas (CH₄) storage in a deep saline aquifer at Rivara (MO), Northern Italy. This paper discusses the areal distribution of CO₂ and CH₄ fluxes and CO₂, CH₄, Rn, He, H₂ concentrations both in soils and shallow aquifers above the proposed storage reservoir. The distribution of pathfinder elements such as ²²²Rn, He and H₂ has been studied in order to identify potential faults and/or fractures related to preferential migration pathways and the possible interactions between the reservoir and surface. A geochemical and isotopic characterization of the ground waters circulating in the first 200 m has allowed to investigation of (i) the origin of the circulating fluids, (ii) the gas–water–rock interaction processes, (iii) the amount of dissolved gases and/or their saturation status. In the first 200 m, the presence of CH₄-rich reducing waters are probably related to organic matter (peat) bearing strata which generate shallow-derived CH₄, as elsewhere in the Po Plain. On the basis of isotopic analysis, no hints of thermogenic CH₄ gas leakage from a deeper reservoir have been shown. The δ¹³C(CO₂) both in ground waters and free gases suggests a prevalent shallow origin of CO₂ (i.e. organic and/or soil-derived). The acquisition of pre-injection data is strategic for the natural gas storage development project and as a baseline for future monitoring during the gas injection/withdrawing period. Such a geochemical approach is considered as a methodological reference model for future CO₂/CH₄ storage projects.     

Experimental Study of Cement - Sandstone/Shale - Brine - CO2 Interactions

Background

Reactive-transport simulation is a tool that is being used to estimate long-term trapping of CO₂, and wellbore and cap rock integrity for geologic CO₂ storage. We reacted end member components of a heterolithic sandstone and shale unit that forms the upper section of the In Salah Gas Project carbon storage reservoir in Krechba, Algeria with supercritical CO₂, brine, and with/without cement at reservoir conditions to develop experimentally constrained geochemical models for use in reactive transport simulations.

Results

We observe marked changes in solution composition when CO₂ reacted with cement, sandstone, and shale components at reservoir conditions. The geochemical model for the reaction of sandstone and shale with CO₂ and brine is a simple one in which albite, chlorite, illite and carbonate minerals partially dissolve and boehmite, smectite, and amorphous silica precipitate. The geochemical model for the wellbore environment is also fairly simple, in which alkaline cements and rock react with CO₂-rich brines to form an Fe containing calcite, amorphous silica, smectite and boehmite or amorphous Al(OH)₃.

Conclusions

Our research shows that relatively simple geochemical models can describe the dominant reactions that are likely to occur when CO₂ is stored in deep saline aquifers sealed with overlying shale cap rocks, as well as the dominant reactions for cement carbonation at the wellbore interface.     

Development of a long-term wellbore sealing concept based on numerical simulations and in situ-testing in the Altmark natural gas field

This paper presents an innovative well abandonment concept developed for the long-term containment of CO₂ in depleted Rotliegend gas reservoirs. The new concept aims at amending the conventional standard well abandonment procedure, taking advantage of the natural creeping ability of the thick, homogeneous Zechstein rock salt formation located around 3,000?m in depth (Altmark area) and consists of four main sealing units: (1) a standard sealing element with cement from the reservoir to the impermeable caprock, (2) a salt plug created in the formerly reamed section of casing within the plastic Zechstein (Upper Permian) rock salt formation, (3) two bridge plugs at the bottom and top of the salt plug and (4) a standard sealing element with cement from the top bridge plug until the ground surface. This site-specific study mainly lays emphasis on the development and field testing of the naturally created salt plug, as a key component of the long-term wellbore sealing concept. Comprehensive numerical simulations conducted prior to and during the field test in 2010 and 2011 successfully predicted the evolution of convergence using downhole measurement data. Preliminary results comprise (1) proven convergence of the rock salt formation, (2) a successful coring and (3) restored integrity of Zechstein salt formation, as proven by the formation integrity test. Based on these results, the new long-term sealing concept has been successfully tested at the Altmark natural gas field and successful application of the concept on other sites with similar geological conditions is foreseen to be likely.     

Exploring the effects of data quality,data worth,and redundancy of CO2 gas pressure and saturation data on reservoir characterization through PEST inversion

This study examined the impacts of reservoir properties on carbon dioxide (CO₂) migration after subsurface injection and evaluated the possibility of characterizing reservoir properties using CO₂ monitoring data such as spatial–temporal distributions of gas pressure, which can be reasonably monitored in practice. The injection reservoir was assumed to be located 1,400–1,500 m below the ground surface such that CO₂ remained in the supercritical state. The reservoir was assumed to contain layers with alternating conductive and resistive properties, which is analogous to actual geological formations such as the Mount Simon Sandstone unit. The CO₂ injection simulation used a cylindrical grid setting in which the injection well was situated at the center of the domain, which extended out 8,000 m from the injection well. The CO₂ migration was simulated using the latest version of the simulator, subsurface transport over multiple phases (the water–salt–CO₂–energy module), developed by Pacific Northwest National Laboratory. A nonlinear parameter estimation and optimization modeling software package, Parameter ESTimation (PEST), is adopted for automated reservoir parameter estimation. The effects of data quality, data worth, and data redundancy were explored regarding the detectability of reservoir parameters using gas pressure monitoring data, by comparing PEST inversion results using data with different levels of noises, various numbers of monitoring wells and locations, and different data collection spacing and temporal sampling intervals. This study yielded insight into the use of CO₂ monitoring data for reservoir characterization and how to design the monitoring system to optimize data worth and reduce data redundancy. The feasibility of using CO₂ saturation data for improving reservoir characterization was also discussed.     

Role of Geomechanics in Assessing the Feasibility of CO2 Sequestration in Depleted Hydrocarbon Sandstone Reservoirs

Carbon dioxide (CO₂) sequestration in depleted sandstone hydrocarbon reservoirs could be complicated by a number of geomechanical problems associated with well drilling, completions, and CO₂ injection. The initial production of hydrocarbons (gas or oil) and the resulting pressure depletion as well as associated reduction in horizontal stresses (e.g., fracture gradient) narrow the operational drilling mud weight window, which could exacerbate wellbore instabilities while infill drilling. Well completions (casing, liners, etc.) may experience solids flowback to the injector wells when injection is interrupted due to CO₂ supply or during required system maintenance. CO₂ injection alters the pressure and temperature in the near wellbore region, which could cause fault reactivation or thermal fracturing. In addition, the injection pressure may exceed the maximum sustainable storage pressure, and cause fracturing and fault reactivation within the reservoirs or bounding formations. A systematic approach has been developed for geomechanical assessments for CO₂ storage in depleted reservoirs. The approach requires a robust field geomechanical model with its components derived from drilling and production data as well as from wireline logs of historical wells. This approach is described in detail in this paper together with a recent study on a depleted gas field in the North Sea considered for CO₂ sequestration. The particular case study shows that there is a limitation on maximum allowable well inclinations, 45° if aligning with the maximum horizontal stress direction and 65° if aligning with the minimum horizontal stress direction, beyond which wellbore failure would become critical while drilling. Evaluation of sanding risks indicates no sand control installations would be needed for injector wells. Fracturing and faulting assessments confirm that the fracturing pressure of caprock is significantly higher than the planned CO₂ injection and storage pressures for an ideal case, in which the total field horizontal stresses increase with the reservoir re-pressurization in a manner opposite to their reduction with the reservoir depletion. However, as the most pessimistic case of assuming the total horizontal stresses staying the same over the CO₂ injection, faulting could be reactivated on a fault with the least favorable geometry once the reservoir pressure reaches approximately 7.7 MPa. In addition, the initial CO₂ injection could lead to a high risk that a fault with a cohesion of less than 5.1 MPa could be activated due to the significant effect of reduced temperature on the field stresses around the injection site.     

Impact of CO<Subscript>2</Subscript> injection rate on heat extraction at the HDR geothermal field of Zhacanggou,China

CO₂ is now considered as a novel heat transmission fluid to extract geothermal energy. It can achieve the goal of energy exploitation and CO₂ geological sequestration. Taking Zhacanggou as research area, a “Three-spot” well pattern (one injection with two production), “wellbore–reservoir” coupled model is built, and a constant injection rate is set up. A fully coupled wellbore–reservoir simulator—T2Well—is introduced to study the flow mechanism of CO₂ working as heat transmission fluid, the variance pattern of each physical field, the influence of CO₂ injection rate on heat extraction and the potential and sustainability of heat resource in Guide region. The density profile variance resulting from temperature differences of two wells can help the system achieve “self-circulation” by siphon phenomenon, which is more significant in higher injection rate cases. The density of CO₂ is under the effect of both pressure and temperature; moreover, it has a counter effect on temperature and pressure. The feedback makes the flow process in wellbore more complex. In low injection rate scenarios, the temperature has a dominating impact on the fluid density, while in high rate scenario, pressure plays a more important role. In most scenarios, it basically keeps stable during 30-year operation. The decline of production temperature is <5 °C. However, for some high injection rate cases (75 and 100 kg/s), due to the heat depletion in reservoir, there is a dramatic decline for production temperature and heat extraction rate. Therefore, a 50-kg/s CO₂ injection rate is more suitable for “Three-spot” well pattern in Guide region.     

Geomechanical and geochemical effects on sandstones caused by the reaction with supercritical CO2: an experimental approach to in situ conditions in deep geological reservoirs

The geochemical and geomechanical behaviour of reservoir rocks from deep saline aquifers during the injection and geological storage of CO₂ is studied in laboratory experiments. A combination of geochemical and geomechanical studies was carried out on various sandstones from the North German Basin. After the mineralogical, geochemical and petrophysical characterization, a set of sandstone samples was exposed to supercritical (sc)CO₂ and brine for 2–4 weeks in an autoclave system. One sample was mineralogically and geochemically characterised and then loaded in a triaxial cell under in situ pressure and temperature conditions to study the changes of the geomechanical rock properties. After treatment in the autoclaves, geochemical alterations mainly in the carbonate, but also in the sheet silicate cements as well as in single minerals of the sandstones were observed, affecting the rocks granular structure. In addition to partial solution effects during the geochemical experiments, small grains of secondary carbonate and other mineral precipitations were observed within the pore space of the treated sandstones. Results of additional geomechanical experiments with untreated samples show that the rock strength is influenced by the saturation degree, the confining pressure, the pore fluid pressure and temperature. The exposure to pure scCO₂ in the autoclave system induces reduced strength parameters, modified elastic deformation behaviour and changes of the effective porosity in comparison to untreated sandstone samples. Experimental results show that the volume of pore fluid fluxing into the pore space of the sandstones clearly depends on the saturation level of the sample.     

Thermo-hydro-mechanical modeling of carbon dioxide injection for enhanced gas-recovery (CO2-EGR): a benchmarking study for code comparison

The objective of this paper was to investigate the THM-coupled responses of the storage formation and caprock, induced by gas production, CO₂-EGR (enhanced gas recovery), and CO₂-storage. A generic 3D planer model (20,000?×?3,000?×?100?m, consisting of 1,200?m overburden, 100?m caprock, 200?m gas reservoir, and 1,500?m base rock) is adopted for the simulation process using the integrated code TOUGH2/EOS7C-FLAC3D and the multi-purpose simulator OpenGeoSys. Both simulators agree that the CO₂-EGR phase under a balanced injection rate (31,500?tons/year) will cause almost no change in the reservoir pressure. The gas recovery rate increases 1.4?% in the 5-year CO₂-EGR phase, and a better EGR effect could be achieved by increasing the distance between injection and production wells (e.g., 5.83?% for 5?km distance, instead of 1.2?km in this study). Under the considered conditions there is no evidence of plastic deformation and both reservoir and caprock behave elastically at all operation stages. The stress path could be predicted analytically and the results show that the isotropic and extensional stress regime will switch to the compressional stress regime, when the pore pressure rises to a specific level. Both simulators agree regarding modification of the reservoir stress state. With further CO₂-injection tension failure in reservoir could occur, but shear failure will never happen under these conditions. Using TOUGH-FLAC, a scenario case is also analyzed with the assumption that the reservoir is naturally fractured. The specific analysis shows that the maximal storage pressure is 13.6?MPa which is determined by the penetration criterion of the caprock.     

吉林新立油田下白垩统泉头组成岩储集相及储集空间演化

吉林新立油田位于吉林省松原市郭县以北新庙乡境内。综合应用25口取心井薄片、镜质体反射率、铸体、电镜、X衍射等岩心分析资料，研究了泉头组的成岩作用、成岩演化序列、成岩阶段划分及储集空间类型。根据成岩作用及特有的储集空间组合，划分了4种成岩储集相类型，即A相(不稳定组分强溶解次生孔隙成岩储集相)、B相(中等压实弱-中胶结混合孔隙成岩储集相)、C相(强压实中等胶结残余粒间孔成岩储集相)、D相(碳酸盐强胶结微孔隙成岩储集相)；并阐述了各类成岩储集相的特征，其中A相储集物性最好，B相次之，C相较差，D相最差。最后探讨了泉头组储集空间演化，在中成岩阶段A期形成了大量次生溶蚀孔隙，为首次在该区泉头组特低渗储层中预测相对有利的成岩储集相带提供了研究思路和科学依据，也为改善特低渗油田的开发效果奠定了坚实的地质基础。     

A review of continuous soil gas monitoring related to CCS – Technical advances and lessons learned

One of the most vigorously discussed issues related to Carbon Capture and Storage (CCS) in the public and scientific community is the development of adequate monitoring strategies. Geological monitoring is mostly related to large scale migration of the injected CO₂ in the storage formations. However, public interest (or fear as that) is more related to massive CO₂ discharge at the surface and possible affects on human health and the environment. Public acceptance of CO₂ sequestration will only be achieved if secure and comprehensible monitoring methods for the natural habitat exist. For this reason the compulsory directive 2009/31/EG of the European Union as well as other international regulations demand a monitoring strategy for CO₂ at the surface. The variation of CO₂ emissions of different soil types and vegetation is extremely large. Hence, reliable statements on actual CO₂ emissions can only be made using continuous long-term gas-concentration measurements. Here the lessons learned from the (to the authors’ knowledge) first world-wide continuous gas concentration monitoring program applied on a selected site in the Altmark area (Germany), are described.This paper focuses on the authors’ technical experiences and recommendations for further extensive monitoring programs related to CCS. Although many of the individual statements and suggestions have been addressed in the literature, a comprehensive overview is presented of the main technical and scientific issues. The most important topics are the reliability of the single stations as well as range of the measured parameters. Each selected site needs a thorough pre-investigation with respect to the depth of the biologically active zone and potential free water level. For the site installation and interface the application of small drill holes is recommended for quantifying the soil gas by means of a closed circuit design. This configuration allows for the effective drying of the soil gas and avoids pressure disturbance in the soil gas. Standard soil parameters (humidity, temperature) as well as local weather data are crucial for site specific interpretation of the data. The complexity, time and effort to handle a dozen (or even more) single stations in a large case study should not be underestimated. Management and control of data, automatic data handling and presentation must be considered right from the beginning of the monitoring. Quality control is a pre-condition for reproducible measurements, correct interpretation and subsequently for public acceptance. From the experience with the recent monitoring program it is strongly recommended that baseline measurements should start at least 3 a before any gas injection to the reservoir.     

Production of gas from coal seams in the Upper Silesian Coal Basin in Poland in the post-injection period of an ECBM pilot site

A pilot site for CO₂ storage in coal seams was set-up in the Upper Silesian Coal Basin in Poland in the scope of the RECOPOL project, funded by the European Commission. About 760 tons CO₂ were injected into the reservoir from August 2004 to June 2005. Breakthrough of the injected CO₂ was established, which resulted in the production of about 10% of the injected CO₂ in this period. This paper reports on activities performed under the European Commission project MOVECBM that aimed at the assessment of the storage performance of the reservoir in the follow-up period, i.e. whether the injected CO₂ was adsorbed onto the coal or whether it was still present as free gas in the pore space. The injection well was used for this purpose, as the production well had to be abandoned for permitting reasons. Several operational periods can be defined between the last injection in June 2005 and the abandonment of the well in October 2007. In the first period the well was shut-in to observe the pressure fall-off, from about 15.0 MPa at the wellhead after the last injection until about 4.5 MPa at the end of 2005. This pressure fall-off curve showed that the reservoir permeability was very low. This seemed to confirm the observed swelling of the coal during the injection period. In the first months of 2006 the pressure at the wellhead was decreased by releasing gas in a controlled way. The amount and composition of the gas were measured. As a result of the pressure reduction, the well flooded with water. A production pump was placed on the former injection well, enabling active production from the coal from March to September 2007. Results of these operations showed that whereas the gas production rates were as expected based on the experience with the production well, the water production was remarkably low. This could be related to permeability issues or, alternatively, indicate a drying effect of the CO₂ in the reservoir. Further, the gas composition showed a predominance of CO₂ over CH₄ during the gas release that changed gradually into a predominance of CH₄ over CO₂ during the production phase. Although stabilization was not reached within the given production period, the composition approached a 60% methane, 40% CO₂ ratio. This indicates that the exchange of these gases is more complex than often envisaged. After removal of the pump the well was filled with water, which ceased the gas release. This indicates that the pressure in the reservoir was back to its original, hydrostatic, state. As the total volume of CO₂ produced was only a fraction of the amount that was injected, it can be concluded that the CO₂ was taken up by the coal and is currently adsorbed. This gives confidence in the long-term stability of the injected CO₂.