雪峰山西侧贵州地区中生代构造特征及其演化

贵州中生代变形主要发生在燕山期,发育三幕褶皱变形、两幕逆冲和三幕走滑。根据区域对比、卷入褶皱的地层和褶皱间的叠加关系,判断三期褶皱的形成顺序依次为近东西向、北东向和南北向,时限在J_3—K_2之间。逆冲推覆构造主要由向北西或西逆冲的近南北向逆冲断层组成,大体与南北向褶皱同时形成;自雪峰构造带西缘向西,依次划分出根部带、中部带和前锋带。但是,在根部带识别出两幕逆冲推覆,其它两带各识别出一幕。走滑断层也有3个方向:东西向、北东向和近南北向。东西向走滑断层呈现出右行压扭的运动学特征,而大多数北东向走滑断层是左行张扭性质的。依据各个方向断层间的切割和限制关系,推测东西向走滑断层最早形成,其次是南北向逆冲断层,北东向走滑断层最晚活动。这些断裂和褶皱特征,总体表现出贵州多重多种复合联合的构造特征,最后,探讨了本区的构造成因模式。     

Folding of passive layers and forms of minor structures near terminations of blind thrust faults—application to the central Appalachian blind thrust

The existence of detachment surfaces or décollement zones beneath folded rocks of the Valley and Ridge and Plateau provinces of the Appalachians has been recognized as an important condition of folding. Large folds at the border between the two provinces resulted primarily from repetition of strata by thrusting of blocks over ramp faults that connect detachement surfaces at different horizons. Some investigators have suggested that folds in the Plateau province of Pennsylvania were produced by splay faults arising from detachment surfaces, but field observations and theoretical analyses by Sherwin and by Wiltschko & Chapple suggest that the folds are a result of buckling of multilayered rocks above a décollement. An exception may be the Burning Springs anticline in West Virginia, which appears to have formed at the termination of a detachment surface.Investigation of the translation of an homogenous, viscous material above a flat detachment surface that terminates laterally indicates that the termination produces a broad, low-amplitude anticline in passive layering as a result of thickening induced by a gradient of shear stresses in the vertical direction. This thickening above the termination of a detachment is a mechanism of folding. If the viscous fluid contained mechanical layering, the fold would become amplified by buckling. Computations of stresses in the material indicate that minor faults should be generated first near the termination of the flat detachment surface. The Burning Springs anticline probably was initiated by termination of a detachment surface and subsequently amplified by buckling.     

Development of bedding-normal boudins in the Pilot Mountains, Nevada

Boudins with long axes (BA) oriented subnormal to bedding and to associated fold axes are observed in folded rocks in a thrust sheet exposed near the base of a regionally extensive allochthon in west-central Nevada, USA. Formation of the boudins is related to development of a regional fold-set coeval with major thrusting. The axes of boudins lie at a high angle to bedding, and in some instances, boudins define tight to isoclinal folds which are geometrically associated with the regional deformation. Quartz c-axis fabrics from oriented thin-sections of the boudins indicate extension parallel to the boudin axes (BA).

These relations and other mesoscopic structural data indicate a complex deformational history for boudin development. The history involves thin layers (to become boudins) deformed in folds disharmonic to major structures within the thrust sheet followed by flattening and associated extension parallel to fold axes. During flattening, arcuation occurred within the deforming mass resulting in rotation of fold axes and boudin axes (BA) toward the axis of finite extension (X). Extension parallel to BA recorded in the petrofabrics of boudins records incremental strain axes oriented at a high angle (50°) to the finite X and is probably related to an early plane-strain state associated with disharmonic folding. The finite extension (X) is down-dip in axial planes of major folds formed during thrusting and indicates a northwest to southeast transport for the thrusts.     

Fault-related folding in the Ramshorn Peak area,Idaho-Wyoming thrust belt

The Ramshorn Peak area of the Idaho-Wyoming thrust belt lies in the toe of the Prospect thrust sheet along the eastern margin of the exposed part of the thrust belt. The terrain is folded with axes trending N-S and wavelengths ranging from 3 to 4.3 km. Thrusts occur exclusively along the eastern part of the map area where the toe of the Prospect thrust sheet is thinnest. The easternmost thrusts are backthrusts.Monoclinally folded rocks are thrust on less deformed rocks south of Ramshorn Peak. This fold and fault complex is interpreted to have formed by thrusting over a large oblique and small forward step. The oblique step is responsible for the formation of the monocline in the hanging wall of the thrust. All faults and associated folds are rotated by subsequent buckle folding.Second- and third-order folds (folds at the scale of the Ramshorn Peak fold and fault complex and smaller) appear to be isolated features associated with faults (fault-related folds rather than buckle folds) because they are not distributed throughout the map area. These folds were probably initiated by translation and adhesive drag. The early folding was terminated by large translation over a stepped thrust surface which caused additional folding as the hanging wall rocks conformed to the irregular shape of the footwall. The Rich model is utilized to explain the Ramshorn Peak complex because the fold is of monoclinal form and is an isolated feature rather than part of a buckle fold wave-train.     

Geometry and origin of folding in the Neogene sediments of the Gediz Graben,western Anatolia,Turkey

Abstract

A close relationship between formation of approximately upright folds with axes normal to the extension direction and ramp/flat extensional geometries is established for well exposed Neogene syn-extensional rocks on the presently low-angle Gediz detachment fault, along the southern margin of the Gediz Graben region of western Anatolia, Turkey. Three unconformity-bounded sedimentary sequences and several metamorphic extensional allochthons were mapped in the upper-plate of the Gediz detachment. The oldest sedimentary sequence consists of deformed and folded strata of sandstones and conglomerates that are regarded as being deposited in a supra-detachment basin during the Miocene-Early Pliocene. This unit rests unconformably on the extensional allochthonous, but directly in fault contact with the lower-plate mylonitic rocks. The younger slightly tilted Late Pliocene-Pleistocene sedimentary sequences are post-detachment units that are controlled by EW-trending high-angle normal faults. The youngest alluvium comprises the undeformed present-day basin fill of the Gediz Graben. The supra-detachment sedimentary rocks contain a number of kilometric-scale longitudinal folds that are nearly parallel to the east-west-trending fault system of the Gediz Graben. The folds have a steeply inclined bisecting surface, an interlimb angle of 130–150°, and a plunge of <10°. These folds may be interpreted to form as a result of bending in the underlying Gediz detachment fault. The bending may have an alternation of ramp and flat geometries on which a hanging-wall syncline and rollover anticline formed, respectively. This study again shows the importance of local geology in understanding of some spectacular structures of the extensional basins. © 2002 Éditions scientifiques et médicales Elsevier SAS. All rights reserved.     

Geometry and origin of folding in the Neogene sediments of the Gediz Graben,western Anatolia,Turkey

A close relationship between formation of approximately upright folds with axes normal to the extension direction and ramp/flat extensional geometries is established for well exposed Neogene syn-extensional rocks on the presently low-angle Gediz detachment fault, along the southern margin of the Gediz Graben region of western Anatolia, Turkey. Three unconformity-bounded sedimentary sequences and several metamorphic extensional allochthons were mapped in the upper-plate of the Gediz detachment. The oldest sedimentary sequence consists of deformed and folded strata of sandstones and conglomerates that are regarded as being deposited in a supra-detachment basin during the Miocene–Early Pliocene. This unit rests unconformably on the extensional allochthonous, but directly in fault contact with the lower-plate mylonitic rocks. The younger slightly tilted Late Pliocene–Pleistocene sedimentary sequences are post-detachment units that are controlled by EW-trending high-angle normal faults. The youngest alluvium comprises the undeformed present-day basin fill of the Gediz Graben. The supra-detachment sedimentary rocks contain a number of kilometric-scale longitudinal folds that are nearly parallel to the east-west-trending fault system of the Gediz Graben. The folds have a steeply inclined bisecting surface, an interlimb angle of 130–150°, and a plunge of <10°. These folds may be interpreted to form as a result of bending in the underlying Gediz detachment fault. The bending may have an alternation of ramp and flat geometries on which a hanging-wall syncline and rollover anticline formed, respectively. This study again shows the importance of local geology in understanding of some spectacular structures of the extensional basins.     

Quaternary reactivation of flexural-slip folds by diapiric activity: example from the western Ebro Basin (Spain)

In the western sector of the Ebro Basin two types of structures deform the Quaternary terraces and pediments developed by the Ebro River and its tributaries: (1) folds up to 10 km long in the lower levels of fluvial terraces and (2) normal listric faults that produce tilting and rollover anticlines of the Quaternary deposits. Both types of structures are linked to the geometrical and lithological features of the Tertiary beds that underlie the Quaternary deposits. Quaternary folds, whose axes are parallel to the strike of the Tertiary beds, are the result of reactivation of Tertiary large-scale (60 km long) folds due to diapirism of their gypsum cores, where the gypsum units reach a maximum thickness of 3 000 m. This reactivation produced flexural-slip in some beds on the limbs of the folds, bringing about the folding of the overlying Quaternary terraces. The mechanism of Quaternary folding involves layer-parallel shear in alternating Tertiary units and folding linked to detachments and reverse layer-parallel faults. Normal listric faults are widespread throughout the studied area. They are partly parallel to low dipping Tertiary beds and are the result of a NNE-SSW tectonic extension, compatible with minor structures and focal mechanisms of recent earthquakes. The relationship between the two kinds of Quaternary structures indicates that diapirism of the gypsum cores of the anticlines was activated by extensional tectonics.     

Role of extensional structures on the location of folds and thrusts during tectonic inversion (northern Iberian Chain,Spain)

The Aguilón Subbasin (NE Spain) was originated daring the Late Jurassic-Early Cretaceous rifting due to the action of large normal faults, probably inherited from Late Variscan fracturing. WNW-ESE normal faults limit two major troughs filled by continental deposits (Valanginian to Early Barremian). NE-SW faults control the location of subsidiary depocenters within these troughs. These basins were weakly inverted during the Tertiary with folds and thrusts striking E-W to WNW-ESE involving the Mesozoic-Tertiary cover with a maximum estimated shortening of about 12 %. Tertiary compression did not produce the total inversion of the Mesozoic basin but extensional structures are responsible for the location of major Tertiary folds. Shortening of the cover during the Tertiary involved both reactivation of some normal faults and development of folds and thrusts nucleated on basement extensional steps. The inversion style depends mainly on the occurrence and geometry of normal faults limiting the basin. Steep normal faults were not reactivated but acted as buttresses to the cover translation. Around these faults, affecting both basement and cover, folds and thrusts were nucleated due to the stress rise in front of major faults. Within the cover, the buttressing against normal faults consists of folding and faulting implying little shortening without development of ceavage or other evidence of internal deformation.     

川渝湘鄂薄皮构造带多层拆离滑脱系的岩石力学性质及其对构造变形样式的控制

川渝湘鄂多层拆离推覆构造发育于秦岭-大别造山带、雪峰山厚皮构造带与四川盆地之间。这个薄皮构造带是在晚中生代沿一系列岩石薄弱层从南东向北西多层拆离滑脱构造作用下形成的,然而单纯的地表构造地质调查无法揭示各滑脱层是如何控制区内褶皱-断层关系的。因此,对拆离滑脱层进行识别是认识区内构造样式及其成因机制的关键。利用单轴岩石力学实验方法,对取自区内沿达县-大庸地质剖面不同岩性地层组合的样品进行岩石力学分析,并结合前人在区内已经获得的数据,结果表明区内至少发育5个可能的区域性拆离滑脱层。这些滑脱层主要由泥质岩、粉砂岩和泥质灰岩组成的,分别沿下寒武统牛碲塘组(Det I)、下志留统罗惹坪组和龙马溪组 (Det II)、下二叠统栖霞组(Det III)、下三叠统大冶组(Det IV)和中三叠统巴东组 (Det V)发育。野外调查表明,Det I控制了深部构造层次的断弯褶皱和叠瓦扇, Det II 可能控制了中部构造层次的断展褶皱和拆离褶皱,Det III则可能与Det IV和Det V一起,共同控制了上部构造层次的侏罗山式褶皱。     

褶皱相关断裂构造形成条件与发育机制:燕山中部露头尺度变形研究为例

总结了褶皱相关断裂发育机制的3个构造几何学模型:同心圆褶皱模型、膝折带褶皱模型和弯流褶皱模型。基于燕山中部中、新元古界地层中发育的5个露头尺度褶皱及其中、小型断裂构造的实例剖析,探讨了收缩变形过程中褶皱与断裂构造发育时序与褶皱相关断裂构造的产生机制。研究指出,规模与所在褶皱构造相当或略小的断裂构造当中,既有形成时间早于褶皱变形的断层,也有在褶皱变形过程中调节褶皱不同部位应变差异的褶皱相关断裂构造,而且卷入后期变形的早期断裂可能成为制约褶皱成核位置的影响因素,以及成为枢纽叠覆楔构造的形成方式之一。断层位移-距离曲线特征和断层与褶皱变形几何学、运动学关系分析,可用来判断断层、褶皱变形发生相对时序。认为影响褶皱相关断裂构造发育的机制主要有3种:(1)纵弯滑褶皱作用中,翼部顺层滑动受到限制而无法持续时,将通过断层向上切层的方式予以调节,从而形成翼部或转折端揳入逆冲断裂以及背离向斜和指向背斜逆冲断层;(2)各种因素导致的褶皱曲率变化是褶皱相关断裂产生的重要机制之一,褶皱曲率变化可由褶皱轴面的合并和新生直观反映,轴面合并引起褶皱曲率变化的层位,可能是诱发褶皱相关断裂,如背离向斜和指向背斜逆冲构造开始产生的重要部位;(3)能干性差异和强硬层之间距离较大的岩层组合发生纵弯褶皱变形时,软弱岩系在褶皱核部的聚集和逃逸,是迫使递进收缩的强硬层产生褶皱相关断裂构造的重要机制。     

Three-dimensional strain produced by >50 My of episodic extension, Horse Prairie basin area, SW Montana, U.S.A.

The Horse Prairie basin of southwestern Montana is a complex, east-dipping half-graben that contains three angular unconformity-bounded sequences of Tertiary sedimentary rocks overlying middle Eocene volcanic rocks. New mapping of the basin and its hanging wall indicate that five temporally and geometrically distinct phases of normal faulting and at least three generations of fault-related extensional folding affected the area during the late Mesozoic (?) to Cenozoic. All of these phases of extension are evident over regional or cordilleran-scale domains. The extension direction has rotated 90° four times in the Horse Prairie area resulting in a complex three-dimensional strain field with 60% east–west and >25% north–south bulk extension. Extensional folds with axes at high angles to the associated normal fault record most of the three-dimensional strain during individual phases of extension (phases 3a, 3b, and 4). Cross-cutting relationships between normal faults and Tertiary volcanic and sedimentary rocks constrain the ages of each distinct phase of deformation and show that extension continued episodically for more than 50 My. Gravitational collapse of the Sevier fold and thrust belt was the ultimate cause of most of the extension.     

Growing folds and sedimentation of the Gosau Group, Muttekopf, Northern Calcareous Alps, Austria

Analysis of the three-dimensional geometry of Upper Cretaceous clastics in the Muttekopf area (Northern Calcareous Alps, Austria) indicate fold and fault structures active during deposition. Coniacian continental to neritic sedimentation (Lower Gosau Subgroup) was contemporaneous with displacements on NW-trending faults and minor folding along NE-trending axes. From the Santonian onwards (sedimentation of the deep-marine Upper Gosau Subgroup) the NW-trending faults were sealed and large folds with WSW-trending axes developed. The direction of contraction changed to N-S after the end of Gosau deposition in the Danian (Paleocene). Synorogenic sedimentation patterns indicate continuous contraction from the Coniacian to the Late Maastrichtian/?Danian. Therefore, large-scale extension as observed in the central part of the Eastern Alps cannot be documented in the western parts of the Northern Calcareous Alps. A combination of subduction tectonic erosion for the frontal parts and gravitational adjustment of an unstable orogen after nappe stacking for the internal parts possibly accounts for the different development of Gosau basins in the frontal and trailing regions of the Austroalpine wedge.     

雪峰山西侧贵州地区中生代构造特征及其演化

贵州中生代变形主要发生在燕山期,发育三幕褶皱变形、两幕逆冲和三幕走滑。根据区域对比、卷入褶皱的地层和褶皱间的叠加关系,判断三期褶皱的形成顺序依次为近东西向、北东向和南北向,时限在J3—K2之间。逆冲推覆构造主要由向北西或西逆冲的近南北向逆冲断层组成,大体与南北向褶皱同时形成; 自雪峰构造带西缘向西,依次划分出根部带、中部带和前锋带。但是,在根部带识别出两幕逆冲推覆,其它两带各识别出一幕。走滑断层也有3个方向：东西向、北东向和近南北向。东西向走滑断层呈现出右行压扭的运动学特征,而大多数北东向走滑断层是左行张扭性质的。依据各个方向断层间的切割和限制关系,推测东西向走滑断层最早形成,其次是南北向逆冲断层,北东向走滑断层最晚活动。这些断裂和褶皱特征,总体表现出贵州多重多种复合联合的构造特征,最后,探讨了本区的构造成因模式。     

Geological evolution and structural style of the Palaeozoic Tafilalt sub‐basin,eastern Anti‐Atlas (Morocco,North Africa)

The Tafilalt is one of a number of generally unexplored sub‐basins in the eastern Anti‐Atlas of Morocco, all of which probably underwent a similar tectono‐stratigraphic evolution during the Palaeozoic Era. Analysis of over 1000 km of 2‐D seismic reflection profiles, with the interpretation of ten regional seismic sections and five isopach and isobath maps, suggests a multi‐phase deformation history for the Palaeozoic‐aged Tafilalt sub‐basins. Extensional phases were probably initiated in the Cambrian, followed by uniform thermal subsidence up to at least the end of the Silurian. Major extension and subsidence did not begin prior to Middle/Upper Devonian times. Extensional movements on the major faults bounding the basin to the north and to the south took place in synchronisation with Upper Devonian sedimentation, which provides the thickest part of the sedimentary sequence in the basin. The onset of the compressional phase in Carboniferous times is indicated by reflectors in the Carboniferous sequence progressively onlapping onto the Upper Devonian sequence. This period of compression developed folds and faults in the Upper Palaeozoic‐aged strata, producing a structural style characteristic of thin‐skinned fold and thrust belts. The Late Palaeozoic units are detached over a regional décollement with a northward tectonic vergence. The folds have been formed by the process of fault‐propagation folding related to the thrust imbricates that ramp up‐section from the décollement. Copyright © 2007 John Wiley & Sons, Ltd.     

Kinematics of compressional fold development in convergent wrench terranes

Kinematic models are presented for compressional fold development in wrench and convergent wrench terranes that relate fold shortening, axial rotation, and axial extension. Fold shortening may be derived from final fold geometry. Existing fold geometry and axial orientation, two readily measurable quantities, provide the data needed to determine the relative components of shearing and convergence within the fold system. Analyses utilizing these kinematic models indicate that folds developed in sedimentary rocks in the wrench borderlands of both the Rineonada and San Andreas wrench faults in central California are the product of strongly convergent wrenching. The axes of these folds have been rotated no more than a few degrees during the course of their development. In contrast, folds developed in the Alpine Schists along the Alpine fault in New Zealand and in Pleistocene sediments along the southern limit of the San Andreas fault suggest an almost pure wrench setting and large (>25 °) axial rotations.

Significant axial extension is inherent in wrench-related compressional folds. This axial extension is commonly manifest in the form of normal and strike-slip faults that are internal to the folds and trend at high angles to the fold axes. The relative amount of axial extension diminishes as the degree of convergence increases. This axial extension, and the associated extensional features, can be a diagnostic indication of the influence of wrenching.     

Structural control on gold mineralization at Walhalla,Victoria

Gold mineralization associated with quartz reefs is related to the structural history of the Early Devonian, Walhalla Group. These reefs are situated in the Walhalla Synclinorium, developed during the Middle to Late Devonian Tabberabberan Orogeny. A pervasive north‐south‐trending axial planar cleavage and two styles of folding were produced during regional east‐west compression. The first are upright, open to close folds with sub‐horizontal fold axes. The second are plunging inclined, close to tight folds with fold axes that plunge steeply to the north and south. An extensional event is associated with the emplacement of the Woods Point Dyke swarm and a set of normal faults that offset all earlier structures. High‐angle reverse faults, which post‐date the folding and the emplacement of the dykes, were utilized as conduits for hydrothermal fluids and preferentially localize mineralization to laminated quartz veins. En echelon vein arrays formed during initial stages of reverse faulting became deformed during prolonged shearing to produce ptygmatic veins. Laminated quartz veins within high‐angle reverse faults contain arsenopyrite and pyrite in vein margins and gold in fractures that cross‐cut continuous quartz crystals. Gold, galena, chalcopyrite and sphalerite may also be deposited adjacent to and within fractured arsenopyrite and pyrite. Late‐stage, cross faults developed in a regime of north‐south compression and post‐date the laminated quartz veins and mineralization.     

Late Cretaceous extension overprinting a steep belt in the Northern Calcareous Alps (Schesaplana, R?tikon, Switzerland and Austria)

The Triassic to Cretaceous sediment succession of the Lechtal Nappe in the western part of the Northern Calcareous Alps (NCA) has been deformed into large-scale folds and crosscut by thrust and extensional faults during Late Cretaceous (Eoalpine) and Tertiary orogenic processes. The following sequence of deformation is developed from overprinting relations in the field: (D1) NW-vergent folds related to thrusting; (D2) N–S shortening leading to east–west-trending folds and to the formation of a steep belt (Arlberg Steep Zone) along the southern border of the NCA; (D3) E–W to NE–SW extension and vertical shortening, leading to low-angle normal faulting and recumbent “collapse folds” like the Wildberg Syncline. D1 and D2 are Cretaceous in age and predate the Eocene emplacement of the Austroalpine on the Penninic Nappes along the Austroalpine basal thrust; the same is probably true for D3. Finally, the basal thrust was deformed by folds related to out-of-sequence thrusting. These results suggest that the NCA were at least partly in a state of extension during the sedimentation of the Gosau Group in the Late Cretaceous.     

Ancient synsedimentary structural control on thrust ramp development: an example from the Northern Apennines, Italy

The Umbria-Marche-Sabina foreland fold and thrust belt (Northern Apennines, Italy) provides excellent test-cases for the hypothesis of ancient syndepositional structural features controlling thrust ramp development. The sedimentary cover, Late Triassic to Miocene in age, is made of platform and pelagic carbonates, whose deposition was controlled by significant synsedimentary extension. Normal faulting, mainly during the Jurassic and the Late Cretaceous-Palaeogene, determined sensible lateral thickness variations within the relative sequences. By late Miocene the sedimentary cover was detached from its basement along a mainly evaporitic horizon, and was deformed by means of eastward-verging folds and thrusts.
In order to locate the points where thrust ramps branch-off the basal detachment, both line-length and equal-area techniques were used in the construction of a balanced cross-section through three major fault-related folds in southeastern Umbria. The nucleation of thrust ramps was controlled by the occurrence of Jurassic and Cretaceous-Palaeogene synsedimentary normal faults. These interrupted the lateral continuity of the evaporitic unit (the Late Triassic Anidriti di Burano Fm.) at the base of the sedimentary cover, and acted as obstacles to the eastward propagation of the thrust system, giving rise to major folds which originated from tip-line folding processes.
Therefore, the inferred relationships between ancient normal faults and late thrusts indicate that synsedimentary tectonic structures and the related lateral stratigraphic variations can be envisaged as mechanically important perturbations, which effectively control the nucleation and development of thrust ramps.     

MULTISTAGE SUPERIMPOSED DEFORMATION AND THEEVOLUTION OF THE NORTHEASTERN MARGIN OF YANGTZE BLOCK

Multistage superimposed deformation has been discussed systematically based on the progress of the stratigraphic sequences of the northeastern margin of Yangtze Block. The new-discovered first stage deformation of those sequences occurred from the middle Triassic to the end of early Jurassic together with development of regional folding, which was resulted from the deep detachment shearing tending toward NW-WNW. The folds dip to east and fall down toward west, and were superimposed by the main stage folding. Thereafter, a series of folds were developed with axes trending toward northeast. Consequently normal folds occurred on the normal limbs while overturned fold on the overturned limbs during the first stage folding. The detachment or thrust was form edfrom late Jurassic to early Cretaceous. Due to the uplifting of Dabie and the Wannan Mountains in the north and south sides, the bi-directional thrusting belt was formed by gravity flowing from the Mountains toward the center of the basin along the north side of Xuancheng and south side of Guichi. The deformation geodynamics was discussed simply based on the newly recognized information about the tectonic evolution.     

河南木厂河区银、金、铜矿床的构造控矿特征

河南木厂河地区,位于秦岭-大别山中央造山带的东部,桐柏-大别构造亚带东段。区内以长期活动的NWW-近EW向深大断裂及派生的NWW向,SN向断裂以及平行于东部郯庐断裂带的NE向断裂为主要特征,褶皱表现为形态复杂的宽缓线形。通过调查研究,确认了木厂河矿区存在三个构造岩石单元:核杂岩单元(CC)、超高压单元(UHP)、高压单元(HP).各单元之间发育有大型的拆离断层,有利于成矿元素富集。本区矿床的形成与大别山超高压变质带折返后的伸展拆离作用密切相关。矿体形成部位主要在核杂岩单元之上,超高压单元之下的拆离断层带。拆离断层对本区的矿化起了重要的控制作用。