任意空间取向TI介质qP和qSV波解耦的波动方程

由于构造运动等作用,TI介质对称轴往往沿空间任意方向分布,具有任意空间取向对称轴的TI（ATI）介质更符合实际地质情况.VTI介质与ATI介质的相速度在形式上具有一致性,VTI介质中地震波的相角对应ATI介质对称轴与地震波传播方向的夹角.本文基于Tsvankin的VTI介质精确相速度公式,利用TI介质对称轴和地震波传播方向上单位向量的数量积和向量积来计算ATI介质的精确相速度.根据弱各向异性假设,导出qP波和qSV波的近似相速度,分析了近似公式的误差,讨论总结了ATI介质qP波和qSV波的相速度特征.本文中的单位向量采用观测坐标系表示,通过相角关系,可以较为方便地由ATI介质近似相速度导出频散关系,然后借助傅里叶逆变换推导出时间-波数域qP波和qSV波解耦的波动方程.数值算例表明本文的波动方程是qP波和qSV波解耦的,波场计算结果稳定,未出现明显的数值频散,验证了本文方法的有效性.     

几种弱向异性介质中qSV波速度和偏振异常

研究了在具有生趣对称轴的横向各向同性介质（ＴＩＶ介质）中ｑＳＶ波群速度及偏振矢量,给出了相应的精确和近似公式,进一步讨论了用较简单的近似公式来代替复杂精确公式的可靠性;最后展示了地球内部几种常见各向异性岩石矿物中地震ｓＳＶ波速度各向异性因子、偏振信息及其与传播方向之间的偏差。     

Approximate traveltime inversion in downhole microseismic monitoring

In downhole microseismic monitoring, accurate event location relies on the accuracy of the velocity model. The model can be estimated along with event locations. Anisotropic models are important to get accurate event locations. Taking anisotropy into account makes it possible to use additional data – two S-wave arrivals generated due to shear-wave splitting. However, anisotropic ray tracing requires iterative procedures for computing group velocities, which may become unstable around caustics. As a result, anisotropic kinematic inversion may become time consuming. In this paper, we explore the idea of using simplified ray tracing to locate events and estimate medium parameters. In the simplified ray-tracing algorithm, the group velocity is assumed to be equal to phase velocity in both magnitude and direction. This assumption makes the ray-tracing algorithm five times faster compared to ray tracing based on exact equations. We present a set of tests showing that given perforation-shot data, one can use inversion based on simplified ray-tracing even for moderate-to-strong anisotropic models. When there are no perforation shots, event-location errors may become too large for moderately anisotropic media.     

横向各向同性介质中地震波走时模拟

横向各向同性介质是地球内部广泛分布的一种各向异性介质.针对这种介质,我们对各向同性介质的最小走时树走时模拟方法进行了推广,推广后的方法可适用于非均匀、对称轴任意倾斜的横向各向同性介质模型.为保证计算效率,最小走时树的构建采用了一种子波传播区域随地震波传播动态变化的改进算法.对于弱各向异性介质,我们使用了一种新的地震波群速度近似表示方法,该方法基于用射线角近似表示相角的思想,对3种地震波（qP, qSV和qSH）均有较好的精度.应用本文地震波走时模拟方法对均匀介质、横向非均匀介质模型进行了计算,并将后者结果与弹性波方程有限元方法的模拟结果进行了对比,结果表明两者符合得很好.本文方法可用于横向各向同性介质的深度偏移及地震层析成像的深入研究.     

垂向非均匀介质中转换波转换点计算

转换点位置的计算是转换波资料处理中的一个关键问题. 本文提出了分别基于速度随深度线性变化、速度随垂直走时线性变化、慢度随深度线性变化和慢度随垂直走时线性变化四种等效垂向非均匀介质情况下转换点位置的计算方法. 研究了通过速度拟合、走时近似和相似系数谱三种方式选择合适的等效速度方法. 结合理论模型对非均匀介质转换点计算方法、渐进转换点计算方法、Thomsen近似公式和均匀介质解析计算方法的误差进行了分析,结果表明非均匀介质转换点计算方法能更准确地计算转换点位置.     

基于牛顿迭代法求解群速度的地震波射线追踪模拟

地下介质中普遍存在着各向异性,当前基于各向异性的地震波射线追踪多是在弱各向异性介质中进行且采用群速度近似表示方法,这些近似方法在强各项异性介质中会导致很大误差而无法真正模拟地震波的传播规律。根据地下普遍存在各向异性的事实和地震波基本传播规律,提出利用牛顿迭代法高效求解群速度,基于Paraview平台自动化构建三维地质模型,采用最短路径法进行地震波射线追踪模拟及可视化,实现对复杂三维地质的速度不均匀性和各向异性的表达,为三维地质模型的构建和地震波射线追踪模拟及可视化提供一种新思路,并以华北克拉通山西断陷带北部局部区域为例进行研究。结果表明,该方法能够减少由各向异性对地震波传播模拟造成的影响,清晰表达了研究区地质结构和各向异性特点,在对复杂三维地质结构的解读中能够较好应用。     

TTI介质弹性波相速度与偏振特征分析

相速度和偏振方向是研究地震波传播规律和描述介质特性的重要参数,在理论研究和实际应用中有重要作用.本文假定倾斜横向各向同性(TTI)介质对称轴位于观测坐标系XOZ面内,在此观测坐标系下直接推导了TTI介质弹性波相速度和偏振方向的解析表达式,再进一步利用Thomsen弱各向异性理论,推导了弱各向异性近似条件下弹性波相速度以及qP波和qSV波偏振方向表达式.理论分析和数值试例表明,在相速度方面,随着各向异性介质参数改变,qP波和qSH波速度变化较为平缓,qSV波速度变化较为剧烈.弹性波相速度近似式误差均较小,能较好地近似精确相速度.在偏振方向方面,SH波偏振方向只是传播方向和对称轴倾角的函数,而与各向异性参数无关,SH波偏振方向既垂直于传播方向,又垂直于TTI介质对称轴方向.除特定方向外,qP波和qSV波的偏振方向与传播方向均成一定角度,并且随TTI介质对称轴倾角的改变而改变;在精确和近似情况下,qP波和qSV波的偏振方向始终垂直;在精度允许范围内,偏振方向的弱各向异性近似式与理论解析式吻合较好.     

应力诱导各向异性介质中地震波的传播

主要讨论了应力变化如何影响各向异性介质中波速度的问题。推导了一般各向异性介质在初始应力下的Christoffel方程,得到介质中3种波的相速度和初始应力的关系表达式;通过实验数据验证了单轴应力能够诱导各向异性,当施加单轴应力时,速度在沿应力的方向增加最大,在垂直应力的方向增加最小,实验结果与理论推导一致;用Christoffel方程的数值解模拟在3种对称情况下的弹性各向异性介质中初始应力对波速度的影响。数值结果表明:初始应力对各向异性介质中波传播速度的影响,随着各向异性强度的增加而增大,而且速度越慢,影响越大。     

A Fast Sweeping Scheme for Calculating P Wave First-Arrival Travel Times in Transversely Isotropic Media with an Irregular Surface

Seismic wave propagation shows anisotropic characteristics in many sedimentary rocks. Modern seismic exploration in mountainous areas makes it important to calculate P wave travel times in anisotropic media with irregular surfaces. The challenges in this context are mainly from two aspects. First is how to tackle the irregular surface in a Cartesian coordinate system, and the other lies in solving the anisotropic eikonal equation. Since for anisotropic media the ray (group) velocity direction is not the same as the direction of the travel-time gradient, the travel-time gradient no longer serves as an indicator of the group velocity direction in extrapolating the travel-time field. Recently, a topography-dependent eikonal equation formulated in a curvilinear coordinate system has been established, which is effective for calculating first-arrival travel times in an isotropic model with an irregular surface. Here, we extend the above equation from isotropy to transverse isotropy (TI) by formulating a topography-dependent eikonal equation in TI media in the curvilinear coordinate system, and then use a fast sweeping scheme to solve the topography-dependent anisotropic eikonal equation in the curvilinear coordinate system. Numerical experiments demonstrate the feasibility and accuracy of the scheme in calculating P wave travel times in TI models with an irregular surface.     

Elastic wave propagation in inhomogeneous anisotropic media

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｍｅｄｉａｉｎｅａｒｔｈａｒｅｑｕｉｔｅｃｏｍｐｌｅｘ．Ｔｈｅｒｅｅｘｉｓｔｓｅｖｅｒａｌｕｎｃｏｎｔｉｎｕｏｕｓｐｌａｉｎｓ．Ｎｏｒｍａｌｙ,ｉｔｉｓｕｓｅｄｔｏａｐｐｒｏｘｉｍａｔｅｒｅａｌｍｅｄｉｕｍｗｉｔｈｌａｙ...     

2021年3月5日新西兰克马德克群岛M7.8面波震级测定差异分析

2021年3月5日新西兰克马德克群岛发生M7.8地震,本文计算了全球台网692个台站和中国地震台网全球监测台网112个台站的面波震级,并对此震级进行了偏差分析.结果表明:由于面波震级测定公式的不同,我国和美国测震的面波震级偏差为0.2;面波震级的测定受震源破裂过程的影响,由于此次地震主要破裂方向沿北东向,地震的多普勒效...     

THE APPLICATION OF PML BOUNDARY CODITIONS IN THE SIMULATION OF SEISMIC WAVE BY THE HIGH-ORDER STAGGERED-GRID FINITE DIFFERENCES AT THE TRANSVERSELY ISOTROPIC MEDIA

In the realm of the numerical simulation, finite difference method and finite element method are more intuitive and effective than other simulation methods. In the process of simulating seismic wave propagation, the finite differences method is widely used because of its high computational efficiency and the advantage of the algorithm is more efficient. With the demand of precision, more and more researchers have proposed more effective methods of finite differences, such as the high-order staggered-grid finite differences method, which can restore the actual process of wave propagation on the premise of ensuring accuracy and improving the efficiency of operation. In the past numerical simulation of seismic wave field, different models of isotropic medium are mostly used, but it is difficult to reflect the true layer situation. With the research demand of natural seismology and seismic exploration, the research on anisotropic media is more and more extensive. Transversely isotropic(TI)media can well simulate the seismic wave propagation in the formation medium, such as gas-bearing sandstone, mudstone, shale et al., the character of TI media is reflected by introducing the Thomsen parameters to reflect its weak anisotropy of vertical direction by using Thomson parameter. Therefore, studying the process of seismic wave propagation in TI media can restore the true information of the formation to the greatest extent, and provide a more reliable simulation basis for the numerical simulation of seismic wave propagation. In the geodynamic simulation and the numerical simulation of the seismic wave field, under the limited influence of the calculation area, if no boundary conditions are added, a strong artificial boundary reflection will be generated, which greatly reduces the validity of the simulation. In order to minimize the influence of model boundaries on the reflection of seismic waves, it is often necessary to introduce absorbing boundary conditions. At present, there are three types of absorption boundary conditions: one-way wave absorption boundary, attenuation absorption boundary, and perfectly matched layer(PML)absorption boundary. In terms of numerical simulation of seismic waves, the boundary absorption effect of PML is stronger than the first two, which is currently the most commonly used method, and it also represents the cutting-edge development direction of absorption boundary technology. The perfectly matched layer absorbing boundary is effectively applied to eliminating the reflective waves from model boundaries, but for transversely isotropic medium, the effect of the absorbing is not very well. For this reason, the elastic dynamic wave equations in transversely isotropic media are derived, and we describe a second-order accurate time, tenth-order accurate space, formulation of the Madariaga-Virieux staggered-grid finite difference methods with the perfectly matched layer(PML)are given. In addition, we have established vertical transversely isotropic(VTI)media and arbitrary inclined tilted transversely isotropic(TTI)media models, using a uniform half-space velocity model and a two-layer velocity model, respectively. By combining the actual geoscience background, we set the corresponding parameters and simulation conditions in order to make our model more research-oriented. When setting model parameters, different PML thickness, incident angle, source frequency and velocity layer models were transformed to verify the inhibition of boundary reflection effect by PML absorption boundary layer. The implementations of this simulation show that the formula is correct and for the transversely isotropic(TI)media of any angular symmetry axis, when the thickness of the PML layer reaches a certain value, the seismic wave reflection effect generated by the artificial boundary can be well suppressed, and the absorption effect of PML is not subject to changes in incident angle and wave frequency. Therefore, the results of our study indicate that our research method can be used to simulate the propagation process of seismic waves in the transversely isotropic(TI)media without being affected by the reflected waves at the model boundary to restore the actual formation information and more valuable geological research.     

Transient heterogeneity in an aquifer undergoing bioremediation of hydrocarbons

Localized, transient heterogeneity was studied in a sand aquifer undergoing benzene, toluene, ethylbenzene, and xylene bioremediation using a novel array of multilevel, in situ point velocity probes (PVPs). The experiment was conducted within a sheet-pile alleyway to maintain a constant average flow direction through time. The PVPs measured changes in groundwater velocity direction and magnitude at the centimeter scale, making them ideal to monitor small-scale changes in hydraulic conductivity (K). Velocities were shown to vary nonuniformly by up to a factor of 3 when a source of oxygen was established down-gradient of the petroleum spill. In spite of these local variations, the average groundwater velocity within the 7 m × 20 m sheet-piled test area only varied within ± 25%. The nonuniform nature of the velocity variations across the gate indicated that the changes were not due solely to seasonal hydraulic gradient fluctuations. At the conclusion of the experiment, microbial biomass levels in the aquifer sediments was approximately 1 order of magnitude higher in the oxygen-amended portion of the aquifer than at the edge of the plume or in locations up-gradient of the source. These data suggest that the transient velocities resulted, at least in part, from enhanced biological activity that caused transient heterogeneities in the porous medium.     

地声与地震相关性的初步探讨

为探索震前声发射的方向与地震的关系,假定声速仅与深度有关,在这种条件下得到的方向公式应该与恒速条件下得到的方向公式一致。为了简化起见,可以用实测时差作为公式中的时差,其误差是允许的。报告中介绍了用互相关函数求时差的方法,并给出部分地声方向的计算结果,初步表明震前声发射的方向与未来震中有着密切关系。     

三维TTI介质相速度和群速度

相速度和群速度是研究地震波传播规律和描述介质特性的重要参数,是弹性波传播理论中的核心内容,在理论研究和实际应用中有重要作用.本文根据VTI介质的刚度矩阵,利用Bond变换建立了TTI介质刚度矩阵.再利用TTI介质刚度矩阵,结合弹性动力学的本构方程、牛顿运动微分方程和几何方程,得到了三维TTI介质弹性波波动方程和Christoffel方程.通过本征值方法求解Christoffel方程,推导了三维TTI介质弹性波相速度的解析表达式.利用Berryman和Crampin推导各向异性介质群速度公式,根据三维TTI介质的相速度解析式推导了三维TTI介质群速度解析表达式.数值试例表明,随着各向异性介质参数改变,TI介质弹性波相速度变化较为平缓,群速度变化较为剧烈,qP波和SH波速度变化较为平缓,qSV波速度变化较为剧烈.     

2.5D modelling, inversion and angle migration in anisotropic elastic media

2.5D modelling approximates 3D wave propagation in the dip‐direction of a 2D geological model. Attention is restricted to raypaths for waves propagating in a plane. In this way, fast inversion or migration can be performed. For velocity analysis, this reduction of the problem is particularly useful. We review 2.5D modelling for Born volume scattering and Born–Helmholtz surface scattering. The amplitudes are corrected for 3D wave propagation, taking into account both in‐plane and out‐of‐plane geometrical spreading. We also derive some new inversion/migration results. An AVA‐compensated migration routine is presented that is simplified compared with earlier results. This formula can be used to create common‐image gathers for use in velocity analysis by studying the residual moveout. We also give a migration formula for the energy‐flux‐normalized plane‐wave reflection coefficient that models large contrast in the medium parameters not treated by the Born and the Born–Helmholtz equation results. All results are derived using the generalized Radon transform (GRT) directly in the natural coordinate system characterized by scattering angle and migration dip. Consequently, no Jacobians are needed in their calculation. Inversion and migration in an orthorhombic medium or a transversely isotropic (TI) medium with tilted symmetry axis are the lowest symmetries for practical purposes (symmetry axis is in the plane). We give an analysis, using derived methods, of the parameters for these two types of media used in velocity analysis, inversion and migration. The kinematics of the two media involve the same parameters, hence there is no distinction when carrying out velocity analysis. The in‐plane scattering coefficient, used in the inversion and migration, also depends on the same parameters for both media. The out‐of‐plane geometrical spreading, necessary for amplitude‐preserving computations, for the TI medium is dependent on the same parameters that govern in‐plane kinematics. For orthorhombic media, information on additional parameters is required that is not needed for in‐plane kinematics and the scattering coefficients. Resolution analysis of the scattering coefficient suggests that direct inversion by GRT yields unreliable parameter estimates. A more practical approach to inversion is amplitude‐preserving migration followed by AVA analysis. SYMBOLS AND NOTATION A list of symbols and notation is given in Appendix D .     

Surface waves in isotropic,laterally inhomogeneous media

Summary Two different viewpoints of the phase velocities of the elastic surface waves in isotropic, laterally inhomogeneous media have led to inconsistent results. Arguments in terms of surface wave modes give the conclusion that the phase velocity is independent of the propagation direction, while the outcome of calculations based on a constructive interference of body waves in a surface layer is that the phase velocity is dependent on the propagation direction. Both arguments are summarized and an error in the calculations giving dependence is pointed out. The calculations and observations of surface wave amplitude changes in laterally inhomogeneous media are also summarized.     

利用伪谱法模拟横向各向同性介质中的波

介质的弹性常数为三维四阶张量的分量,共有８１个,由于应力张量和应变张量的对称性及能量密度是应变的二次函数,一般各向异常性介质的独立弹性常数可减为２１个,如果介质具有较高的对称性,独立弹性常数的数目会更少。 对于地壳和上地幔,具有５个独立弹性常数的横向各向同性介质是一个非常好的近似,本研究中横向各向同性介质的对称轴方向可以是任意的（即对称轴可以不平等于铅直方向）,在此情况下,需要进行坐标变换,如果已知介质在某一坐标系（其坐标轴平行或垂直于介质的对称轴）中的弹性常数,我们能够容易地利用变换公式得到变换后新坐标系中的弹性常数。 本文提出了一种方案,利用伪谱法既能模拟横向各向同性介质中的平面波,也能模拟点源激发的波场。在勘探地球物理和地震学中,模拟横向各向同性介拮中传播的平面波及区域源产生的波是最重要的研究课题之一。然而在一般各向异性介质中,很难或不可能确定弹性波的相速度和偏振方向,但在横向各向同性介质中,则可以通过坐标变换来实现,这里我们所提出的方法可以用于横向各向同性介质中弹性波的模拟。     

Generalized Dix equation and analytic treatment of normal-moveout velocity for anisotropic media*

Despite the complexity of wave propagation in anisotropic media, reflection moveout on conventional common-midpoint (CMP) spreads is usually well described by the normal-moveout (NMO) velocity defined in the zero-offset limit. In their recent work, Grechka and Tsvankin showed that the azimuthal variation of NMO velocity around a fixed CMP location generally has an elliptical form (i.e. plotting the NMO velocity in each azimuthal direction produces an ellipse) and is determined by the spatial derivatives of the slowness vector evaluated at the CMP location. This formalism is used here to develop exact solutions for the NMO velocity in anisotropic media of arbitrary symmetry. For the model of a single homogeneous layer above a dipping reflector, we obtain an explicit NMO expression valid for all pure modes and any orientation of the CMP line with respect to the reflector strike. The contribution of anisotropy to NMO velocity is contained in the slowness components of the zero-offset ray (along with the derivatives of the vertical slowness with respect to the horizontal slownesses) — quantities that can be found in a straightforward way from the Christoffel equation. If the medium above a dipping reflector is horizontally stratified, the effective NMO velocity is determined through a Dix-type average of the matrices responsible for the ‘interval’ NMO ellipses in the individual layers. This generalized Dix equation provides an analytic basis for moveout inversion in vertically inhomogeneous, arbitrarily anisotropic media. For models with a throughgoing vertical symmetry plane (i.e. if the dip plane of the reflector coincides with a symmetry plane of the overburden), the semi-axes of the NMO ellipse are found by the more conventional rms averaging of the interval NMO velocities in the dip and strike directions. Modelling of normal moveout in general heterogeneous anisotropic media requires dynamic ray tracing of only one (zero-offset) ray. Remarkably, the expressions for geometrical spreading along the zero-offset ray contain all the components necessary to build the NMO ellipse. This method is orders of magnitude faster than multi-azimuth, multi-offset ray tracing and, therefore, can be used efficiently in traveltime inversion and in devising fast dip-moveout (DMO) processing algorithms for anisotropic media. This technique becomes especially efficient if the model consists of homogeneous layers or blocks separated by smooth interfaces. The high accuracy of our NMO expressions is illustrated by comparison with ray-traced reflection traveltimes in piecewise-homogeneous, azimuthally anisotropic models. We also apply the generalized Dix equation to field data collected over a fractured reservoir and show that P-wave moveout can be used to find the depth-dependent fracture orientation and to evaluate the magnitude of azimuthal anisotropy.     

多次透射公式的一种高频失稳机制

本文利用一维双曲型偏微分方程组初边值问题数值稳定性的GKS定理的物理解释和推广，分析了多次透射公式在数值实现中可能出现的一种高频失稳机制，即在多维离散网格，沿某一空间方向的外行简谐波，由于与其他空间方向节点运动的耦合效应可以使能量传播方向反向。文中通过数值试验对这一失稳机制作了初步验证。