隔震结构地震反应分析的实用计算方法

根据上部结构和隔震单元特性对隔震结构反应的影响,提出了可用于隔震结构反应分析的简易方法,避免从数学上求解耦联的非线性方程.将隔震层的恢复力模型等效线性化,以结构动力响应的Duhamel积分为基础,提出了一种新的结构动力响应的数值计算方法.     

结构偏心对基础隔震结构地震反应的影响

本文对基础隔震偏心结构在不同场地上的地震动作用下的反应进行了深入研究，探讨了上部结构偏心、隔震层偏心、场地条件等因素对于基础隔震结构地震反应的影响，选取了能反映结构偏心特性的参数，以便将分析各因素对隔震结构地震反应的影响转化为分析参数的影响。通过大量的数值计算与分析，得到了一些对实际工程有意义的结论。     

高层隔震结构的等效简化模型研究

Kelly和周锡元等曾对规则型隔震结构上部单自由度模型进行过讨论，给出了必要的计算公式。对各种中低层规则型隔震建筑，应用此公式可获得满意的结果。近来隔震技术逐渐被应用到高层建筑中。对于高层隔震体系，上部结构的高阶振型效应不能忽略，此时应用单自由度模型将产生较大误差。为此，本文采用上部结构周期和总基底剪力相等的准则，推导了等效模型的结构参数公式，并通过数值模拟分析给出了等效模型简化确定方法。通过对原结构和等效模型结构的地震反应分析，证明了这种等效方法是简便有效的。     

基于强震观测的隔震结构地震反应分析

福建省防灾减灾中心大楼是一栋高约40m,安装有强震观测系统的隔震大楼,目前该结构台阵已记录到30多次地震引起的大楼地震反应。本文利用具有强大非线性功能的ETABS软件建立大楼结构模型,同时考虑隔震结构的楼梯和填充墙对结构地震反应的影响,并利用台阵记录验证大楼结构模型线弹性地震反应的可靠性,说明隔震大楼结构模型能很好地模拟大楼的地震反应过程。在此基础上结合大楼原型动力性能实验的实测参数,以大楼自由场地的三个实际地震记录作为输人,对大楼在中小地震作用下非线性地震反应进行分析,结果表明大楼具有良好的隔震效果。     

摩擦摆隔震结构地震反应谱的计算分析

探讨了摩擦摆基底隔震结构的地震反应谱规律。采用上部结构-摩擦摆两质点模型并利用系统振动微分方程，计算绘制了设计参数(质量比、摩擦系数、滑道半径)不同取值下上部结构的绝对加速度、侧向位移和基底水平滑移反应谱。结果表明：摩擦摆系统对刚度较大的上部结构具有良好的隔震效果。摩擦系数对上部结构的加速度反应、层间水平侧移和系统滑移均有较大的影响，质量比的影响次之．而滑道半径仅对系统滑移有较为显著的作用。     

组合基础隔震结构双向地震反应分析

本文采用双向耦合恢复力模型模拟组合隔震系统中隔震支座的双向耦合效应,对组合基础隔震结构进行了单向和双向地震反应对比分析,分析表明在水平双向地震作用下结构各层的加速度反应较小,隔震层的层间位移较大,而上部结构的层间位移较小,并且在水平双向地震作用下,支座的最大位移明显大于单向地震作用时支座的最大位移,因而应考虑水平双向地震作用对组合基础隔震结构地震反应和隔震支座性能的影响。     

改进的基础隔震结构地震作用简化计算方法

在《建筑抗震设计规范》(GB50011-2001)关于隔震结构的简化计算方法中,水平向减震系数的表达式和定义有些不符,假定的隔震结构地震作用分布规律也与实际情况略有出入。本文基于水平向减震系数的定义和实际隔震结构的地震作用分布规律提出了一种改进的隔震结构水平向减震系数、隔震结构总地震作用、隔震结构上部地震作用分布的计算方法,并提出了总水平地震作用减震系数的新概念。本文提出的改进方法具有表达准确、物理意义明确的特点。将本文提出的改进算法计算结果与时程分析计算结果比较,结果显示,改进方法的计算结果与时程分析结果接近,且分布规律一致。     

层间隔震结构计算模型的简化分析

本文通过对层间隔震结构整体动力性能及时域反应的分析，用模态综合方法建立了该结构计算分析简化模型。该模型合理、可靠，为建立实用设计方法、推广层间隔震结构的应用提供了有效途径。     

大高宽比隔震结构地震反应的实用分析方法

本文提出了高层隔震结构等大高宽比隔震结构体系地震反应分析的单质点、2质点和3质点剪切型简化计算模型,同时还提出了高宽比影响系数的概念和计算式。这种纯剪切的简化计算模型成功地模拟了剪切加转动多质点计算模型的动力特性,通过高宽比影响系数对剪切型计算模型得到的剪力系数进行非线性放大,使数十质点的隔震结构体系都能够简化成单质点、2质点和3质点体系进行地震反应分析。文末对22层高宽比为5．01的某22层隔震结构进行了算例分析,简化计算理论的计算结果和时程分析法计算结果一致性良好。     

隔震悬挂结构体系的单质点等效动力计算模型

通过研究双质点模型自由振动特性发现,当质量比与刚度比在某一特定范围内时,二阶振型的贡献度远小于一阶振型的.因此,隔震悬挂结构可由双质点模型等效简化为单质点模型进行计算分析.数值计算对比分析结果表明:由等效单质点模型计算的体系基本自振频率与双质点模型的一阶频率非常接近,最多相差0.3% 左右;两种模型计算的被悬挂结构相对...     

Simplified seismic fragility analysis of structures with two types of friction devices

This paper presents a method and results of seismic fragility estimation of frame structures with friction devices and with friction devices and restrictors. The seismic intensity parameter, defined as the mean value of the pseudovelocity spectrum in a specified periods band, is proved to allow the use of linear regression analysis of the response parameters of the considered non‐linear structures on seismic intensity. A simplified method of fragility estimation is proposed, based on the concept of ‘mean seismic excitation’ and linear regression of the seismic response parameters on seismic intensity parameter. The key risk contributors for the system with friction devices and for the system with friction devices and restrictors are identified on the basis of the fragility analysis, and recommendations for improvement of the seismic response of the respective systems are derived. The results of the fragility study show that when the initial ‘bare’ frame is retrofitted by rigidly connected bracings the effect is much lower than in the case of connecting the bracings by friction devices and especially by friction devices and restrictors. Copyright © 2000 John Wiley & Sons, Ltd.     

隔震立式储罐地震反应谱分析

基于反应谱理论,研究了的基底隔震储罐的地震响应问题.将储罐简化为三质点体系力学模型,罐内连续液体质量等效为对流质量、脉冲质量和刚性质量,并引入隔震刚度.与时程分析对比,验证反应谱法的适用性,分析隔震立式储罐的地震响应并研究主要参数对隔震储液罐地震响应的影响,主要考虑的参数有:(1)场地类别;(2)隔震周期;(3)高径比.结果表明:反应谱法计算隔震立式储罐地震响应是偏于安全的;随着场地类别和隔震周期的增大,基底剪力减震率逐渐降低,晃动波高变化不明显,隔震后,液动压力呈线性变化,液动压力随着场地类别和高径比的增大而增大,随着隔震周期的增大而减小;高径比存在一定的优化段,在优化段内,基底剪力减震率较大,隔震效果较好.     

Numerical investigation on seismic performance of a shallow buried underground structure with isolation devices

A design procedure for improving the seismic performance of unequal-span underground structures by installing isolation devices at the top end of columns is proposed based on the seismic failure mode of frame-type underground structures and the design concept of critical support columns. A two-dimensional finite element model (FEM) for a soil-underground structure with an unequal-span interaction system was established to shed light on the effects of a complex subway station with elastic sliding bearings (ESB) and lead rubber bearings (LRB) on seismic mitigation. It was found that the stiffness and internal force distribution of the underground structure changed remarkably with the installation of isolation devices at the top end of the columns. The constraints of the beam-column joints were significantly weakened, resulting in a decrease in the overall lateral stiffness and an increase in the structural lateral displacement. The introduction of the isolation device effectively reduces the internal force and seismic damage of the frame column; however, the tensile damage to the isolation structure, such as the roof, bottom plate, and sidewall, significantly increased compared to those of the non-isolation structure. Although the relative slip of the ESB remains within a controllable range under strong earthquake excitation as well as frame columns with stable vertical support and self-restoration functions, the LRB shows a better performance during seismic failure and better lateral displacement response of the unequal-span underground structure. The analysis results provide new ideas and references for promoting the application of seismic isolation technology in underground structures.     

基础隔震单层偏心结构扭转地震反应分析

采用微分型滞回恢复力模型模拟隔震支座的恢复力特性，对基础隔震单层偏心结构的扭转地震反应进行分析，研究隔震系统偏心距和上部结构偏心距对结构扭转反应的影响。结果表明，采用隔震技术可以显著降低隔震结构的扭转地震反应。     

多层建筑结构水平剪扭-竖向地震反应的智能复合隔震控制

本文在提出了“碟形弹簧-橡胶隔震垫”和MR阻尼器组合而成的智能复合隔震系统的基础上，建立了智能复合隔震系统对多层建筑结构“水平剪扭-竖向”地震反应控制的设计计算方法。提出了智能复合隔震系统对建筑结构水平地震反应的模糊半主动控制策略和对建筑结构竖向地震反应的被动控制方法。以一个五层框架结构为例进行了仿真分析。分析结果表明，本文提出的智能复合隔震系统是一种十分简单和有效的隔震系统。它可克服建筑结构常规隔震系统的两个主要缺点，有效地抑制多层建筑结构的多维地震反应。     

Optimal yield level of bilinear seismic isolation devices

The yield level of an insulator is one of the important parameters which are related to responses and absorbing energy under seismic input energy in isolated structures. The purpose of this paper is to determine the optimal ratios of yield force of the isolator (Q_y) to the total weight of the structures (W). To obtain the optimal ratio, 1044 two-degree-of-freedom isolated bridge models, which have bilinear isolators, were selected. These 2-DOF isolated bridge models with superstructure isolation can consider pier flexibility and various parameters of the isolator. Two formulas for determining the optimal yield ratio are proposed and compared with the previous researches. RAE (the ratio of absorbed energy by the isolator to the total input energy) is related directly to structural responses, and Optimal Yield Ratio (OYR), defined as a yield ratio at maximum RAE, can be obtained from the relationship between RAE and Q_y/W. Here, we found that RAE is a reliable factor to evaluate OYR, and it is proportional to earthquake amplitudes under the same kinds of earthquake loadings. Using the proposed formulas, OYR is determined and the optimal yield force of the isolator can be obtained easily and reliably at a seismic isolation design stage. Copyright © 1999 John Wiley & Sons, Ltd.     

核心筒部分悬挂结构抗震分析的简化力学模型

提出了核心筒部分悬挂结构体系,在已有该体系振动台试验基础上,建立了该体系的抗震分析简化力学模型及其理论公式。按小震、中震和大震3种不同的地震作用情况,分析了该结构体系力学模型和动力方程的差异。利用有限元分析程序SAP2000,对这种结构体系进行了小震和大震作用下的结构地震反应分析,计算结果与试验结果吻合较好。     

Inelastic response of RC frame buildings with seismic isolation

A comprehensive parametric study on the inelastic seismic response of seismically isolated RC frame buildings, designed for gravity loads only, is presented. Four building prototypes, with 23 m × 10 m floor plan dimensions and number of storeys ranging from 2 to 8, are considered. All the buildings present internal resistant frames in one direction only, identified as the strong direction of the building. In the orthogonal weak direction, the buildings present outer resistant frames only, with infilled masonry panels. This structural configuration is typical of many existing RC buildings, realized in Italy and other European countries in the 60s and 70s. The parametric study is based on the results of extensive nonlinear response‐time history analyses of 2‐DOF systems, using a set of seven artificial and natural seismic ground motions. In the parametric study, buildings with strength ratio (F_y/W) ranging from 0.03 to 0.15 and post‐yield stiffness ratio ranging from 0% to 6% are examined. Three different types of isolation systems are considered, that is, high damping rubber bearings, lead rubber bearings and friction pendulum bearings. The isolation systems have been designed accepting the occurrence of plastic hinges in the superstructure during the design earthquake. The nonlinear response‐time history analyses results show that structures with seismic isolation experience fewer inelastic cycles compared with fixed‐base structures. As a consequence, although limited plastic deformations can be accepted, the collapse limit state of seismically isolated structures should be based on the lateral capacity of the superstructure without significant reliance on its inherent hysteretic damping or ductility capacity. Copyright © 2012 John Wiley & Sons, Ltd.     

摩擦隔震结构中不同摩擦力模型在地震作用下结构响应分析

本文选用两种摩擦力模型来分析隔震结构的地震响应，运用newmark方法推导了隔震结构采用库仑摩擦力模型在地震作用下结构响应的计算公式。并编程计算了实例，进行了综合分析，得出质量比、摩擦系数对隔震效果的影响；并给出在其他结构参数相对稳定的条件下，滑移面摩擦系数的取值范围。