Interpretation of a seismic-refraction survey across the Arabian shield in western Saudi Arabia

In February 1978 seismic-refraction profiles were recorded by the U.S. Geological Survey along a 1000 km line across the Arabian Shield in western Saudi Arabia. This report presents a traveltime and relative amplitude study in the form of velocity-depth functions for each individual profile assuming horizontally flat layering. The corresponding cross section of the lithosphere showing lines of equal velocity reaches to a depth of 60–80 km.The crust thickens abruptly from 15 km beneath the Red Sea Rift to about 40 km beneath the Arabian Shield. The upper crust of the western Arabian Shield yields relatively high-velocity material at about 10 km depth underlain by velocity inversions, while the upper crust of the eastern Shield is relatively uniform. The lower crust with a velocity of about 7 km/s is underlain by a transitional crust-mantle boundary. For the lower lithosphere beneath 40 km depth the data indicate the existence of a laterally discontinuous lamellar structure where high-velocity zones are intermixed with zones of lower velocities. Beneath the crust-mantle boundary of the Red Sea rift most probably strong velocity inversions exist. Here, the data do not allow a detailed modelling, velocities as low as 6.0 km/s seem to be encountered between 25 and 44 km depth.     

Crustal structure of the East African Rift zone

A review of seismological data on the crustal structure of the East African Rift zone is presented. The only refraction line is that along the Gregory Rift, which indicates a 7.5 km/sec refractor which is presumed to be the Moho. The bulk of data is provided by surface-wave dispersion studies. Some preliminary measurements of crustal and sub-Moho velocities using the University of Durham array at Kaptagat in Kenya are included.

There is now a growing body of evidence that the crust is generally of shield type over the whole rift zone. The exception is along the axis of the Gregory Rift, where a low-velocity Moho and some crustal modification is apparent. This is presumably the result of magma intrusions and suggests some crustal separation along this section of the rift. Sub-Moho velocities are probably normal outside the rifts themselves, though anomalously low upper-mantle velocities are to be associated with rifting. There is firm evidence for thinning of the lithosphere along the eastern branch of the rift. A cross-section of the Gregory Rift which is consistent with the current data is presented.     

2D model of the crust and uppermost mantle along rift profile, Siberian craton

A two-dimensional model of the crust and uppermost mantle for the western Siberian craton and the adjoining areas of the Pur-Gedan basin to the north and Baikal Rift zone to the south is determined from travel time data from recordings of 30 chemical explosions and three nuclear explosions along the RIFT deep seismic sounding profile. This velocity model shows strong lateral variations in the crust and sub-Moho structure both within the craton and between the craton and the surrounding region. The Pur-Gedan basin has a 15-km thick, low-velocity sediment layer overlying a 25-km thick, high-velocity crystalline crustal layer. A paleo-rift zone with a graben-like structure in the basement and a high-velocity crustal intrusion or mantle upward exists beneath the southern part of the Pur-Gedan basin. The sedimentary layer is thin or non-existent and there is a velocity reversal in the upper crust beneath the Yenisey Zone. The Siberian craton has nearly uniform crustal thickness of 40–43 km but the average velocity in the lower crust in the north is higher (6.8–6.9 km/s) than in the south (6.6 km/s). The crust beneath the Baikal Rift zone is 35 km thick and has an average crustal velocity similar to that observed beneath the southern part of craton. The uppermost mantle velocity varies from 8.0 to 8.1 km/s beneath the young West Siberian platform and Baikal Rift zone to 8.1–8.5 km/s beneath the Siberian craton. Anomalous high Pn velocities (8.4–8.5 km/s) are observed beneath the western Tunguss basin in the northern part of the craton and beneath the southern part of the Siberian craton, but lower Pn velocities (8.1 km/s) are observed beneath the Low Angara basin in the central part of the craton. At about 100 km depth beneath the craton, there is a velocity inversion with a strong reflecting interface at its base. Some reflectors are also distinguished within the upper mantle at depth between 230 and 350 km.     

Upper-mantle structure under the Arabian peninsula

The phase velocity of Rayleigh waves across the Arabian Peninsula has been measured for profiles SHI-HLW, JER-SHI in the northern part and SHI-AAE in the southern part of the peninsula. The phase velocities for the Arabian stable shelf are lower than those for the Canadian shield and higher than those for the Gulf coastal plain of the United States. Shear-velocity models obtained from the inversion of these experimental data show a pronounced low-velocity channel for S-waves which is found throughout the region with a velocity of S in the channel of 4.25–4.45 km/sec. The top of the channel is at 100–140 km depth. This structure differs from those under the Canadian shield and the Gulf Coast. Crustal thickness is 35 ± 8 km.     

Structure of the crust and uppermost mantle of the Yanshan Belt and adjacent regions at the northeastern boundary of the North China Craton from Rayleigh Wave Dispersion Analysis

We have used Rayleigh wave dispersion analysis and inversion to produce a high resolution S-wave velocity imaging profile of the crust and uppermost mantle structure beneath the northeastern boundary regions of the North China Craton (NCC). Using waveform data from 45 broadband NCISP stations, Rayleigh wave phase velocities were measured at periods from 10 to 48 s and utilized in subsequent inversions to solve for the S-wave velocity structure from 15 km down to 120 km depth. The inverted lower crust and uppermost mantle velocities, about 3.75 km/s and 4.3 km/s on average, are low compared with the global average. The Moho was constrained in the depth range of 30–40 km, indicating a typical crustal thickness along the profile. However, a thin lithosphere of no more than 100 km was imaged under a large part of the profile, decreasing to only ~ 60 km under the Inner Mongolian Axis (IMA) where an abnormally slow anomaly was observed below 60 km depth. The overall structural features of the study region resemble those of typical continental rift zones and are probably associated with the lithospheric reactivation and tectonic extension widespread in the eastern NCC during Mesozoic–Cenozoic time. Distinctly high velocities, up to ~ 4.6 km/s, were found immediately to the south of the IMA beneath the northern Yanshan Belt (YSB), extending down to > 100-km depth. The anomalous velocities are interpreted as the cratonic lithospheric lid of the region, which may have not been affected by the Mesozoic–Cenozoic deformation process as strongly as other regions in the eastern NCC. Based on our S-wave velocity structural image and other geophysical observations, we propose a possible lithosphere–asthenosphere interaction scenario at the northeastern boundary of the NCC. We speculate that significant undulations of the base of the lithosphere, which might have resulted from the uneven Mesozoic–Cenozoic lithospheric thinning, may induce mantle flows concentrating beneath the weak IMA zone. The relatively thick lithospheric lid in the northern YSB may serve as a tectonic barrier separating the on-craton and off-craton regions into different upper mantle convection systems at the present time.     

Crustal structure of mainland China from deep seismic sounding data

Since 1958, about ninety seismic refraction/wide angle reflection profiles, with a cumulative length of more than sixty thousand kilometers, have been completed in mainland China. We summarize the results in the form of (1) a new contour map of crustal thickness, (2) fourteen representative crustal seismic velocity–depth columns for various tectonic units, and, (3) a Pn velocity map. We found a north–south-trending belt with a strong lateral gradient in crustal thickness in central China. This belt divides China into an eastern region, with a crustal thickness of 30–45 km, and a western region, with a thickness of 45–75 km. The crust in these two regions has experienced different evolutionary processes, and currently lies within distinct tectonic stress fields. Our compilation finds that there is a high-velocity (7.1–7.4 km/s) layer in the lower crust of the stable Tarim basin and Ordos plateau. However, in young orogenic belts, including parts of eastern China, the Tianshan and the Tibetan plateau, this layer is often absent. One exception is southern Tibet, where the presence of a high-velocity layer is related to the northward injection of the cold Indian plate. This high-velocity layer is absent in northern Tibet. In orogenic belts, there usually is a low-velocity layer (LVL) in the crust, but in stable regions this layer seldom exists. The Pn velocities in eastern China generally range from 7.9 to 8.1 km/s and tend to be isotropic. Pn velocities in western China are more variable, ranging from 7.7 to 8.2 km/s, and may display azimuthal anisotropy.     

Lower crustal intrusions beneath the southern Baikal Rift Zone: Evidence from full-waveform modelling of wide-angle seismic data

The Cenozoic Baikal Rift Zone (BRZ) is situated in south-central Siberia in the suture between the Precambrian Siberian Platform and the Amurian plate. This more than 2000-km long rift zone is composed of several individual basement depressions and half-grabens with the deep Lake Baikal at its centre. The BEST (Baikal Explosion Seismic Transect) project acquired a 360-km long, deep seismic, refraction/wide-angle reflection profile in 2002 across southern Lake Baikal. The data from this project is used for identification of large-scale crustal structures and modelling of the seismic velocities of the crust and uppermost mantle. Previous interpretation and velocity modelling of P-wave arrivals in the BEST data has revealed a multi layered crust with smooth variation in Moho depth between the Siberian Platform (41 km) and the Sayan-Baikal fold belt (46 km). The lower crust exhibits normal seismic velocities around the rift structure, except for beneath the rift axis where a distinct 50–80-km wide high-velocity anomaly (7.4–7.6 ± 0.2 km/s) is observed. Reverberant or “ringing” reflections with strong amplitude and low frequency originate from this zone, whereas the lower crust is non-reflective outside the rift zone. Synthetic full-waveform reflectivity modelling of the high-velocity anomaly suggests the presence of a layered sequence with a typical layer thickness of 300–500 m coinciding with the velocity anomaly. The P-wave velocity of the individual layers is modelled to range between 7.4 km/s and 7.9 km/s. We interpret this feature as resulting from mafic to ultra-mafic intrusions in the form of sills. Petrological interpretation of the velocity values suggests that the intrusions are sorted by fractional crystallization into plagioclase-rich low-velocity layers and pyroxene- and olivine-rich high-velocity layers. The mafic intrusions were probably intruded into the ductile lower crust during the main rift phase in the Late Pliocene. As such, the intrusive material has thickened the lower crust during rifting, which may explain the lack of Moho uplift across southern BRZ.     

Crustal studies of the Koyna region using explosion data from deep seismic soundings

This study is based on the seismic data collected as a result of explosions carried out during the 1976 and 1978 Deep Seismic Sounding (DSS) field operations in the Koyna region. These shots were exploded from twelve shot points by the National Geophysical Research Institute along the Guhagar-Chorochi and Kelsi-Loni profiles.Refraction studies of the records reveal a two-layered crust. The top layer consists 17 km of granite and the second layer 19 km of basalt, giving the average depth of the Moho as 36 km in the region. The velocities of the phases P_g, P* and P_n have been computed as 5.82 ± 0.01, 6.61 ± 0.05 and 8.23 ± 0.05 km/sec respectively and those of S_g, S* and S_n as 3.41 ± 0.00, 4.09 ± 0.07 and 4.60 ± 0.08 km/sec respectively. The shear wave velocity in the basement rock has been found to be lower in comparison with other regions of the peninsular India.In some cases reflections were recorded both from the Moho as well as from the intermediate layer. These reveal a crustal thickness of 39 km with 19 km of granitic and 20 km of basaltic layers.Coda signal durations from DSS explosions recorded by microearthquake seismographs indicate a lateral heterogeneity in the crust on either side of Karad in an east-west direction.     

Upper mantle structure of the South American continent and neighboring oceans from surface wave tomography

We present a new three-dimensional SV-wave velocity model for the upper mantle beneath South America and the surrounding oceans, built from the waveform inversion of 5850 Rayleigh wave seismograms. The dense path coverage and the use of higher modes to supplement the fundamental mode of surface waves allow us to constrain seismic heterogeneities with horizontal wavelengths of a few hundred kilometres in the uppermost 400 km of the mantle.The large scale features of our tomographic model confirm previous results from global and regional tomographic studies (e.g. the depth extent of the high velocity cratonic roots down to about 200–250 km).Several new features are highlighted in our model. Down to 100 km depth, the high velocity lid beneath the Amazonian craton is separated in two parts associated with the Guyana and Guapore shields, suggesting that the rifting episode responsible for the formation of the Amazon basin has involved a significant part of the lithosphere. Along the Andean subduction belt, the structure of the high velocity anomaly associated with the sudbduction of the Nazca plate beneath the South American plate reflects the along-strike variation in dip of the subducting plate. Slow velocities are observed down to about 100 km and 150 km at the intersection of the Carnegie and Chile ridges with the continent and are likely to represent the thermal anomalies associated with the subducted ridges. These lowered velocities might correspond to zones of weakness in the subducted plate and may have led to the formation of “slab windows” developed through unzipping of the subducted ridges; these windows might accommodate a transfer of asthenospheric mantle from the Pacific to the Atlantic ocean. From 150 to 250 km depth, the subducting Nazca plate is associated with high seismic velocities between 5°S and 37°S. We find high seismic velocities beneath the Paraná basin down to about 200 km depth, underlain by a low velocity anomaly in the depth range 200–400 km located beneath the Ponta Grossa arc at the southern tip of the basin. This high velocity anomaly is located southward of a narrow S-wave low velocity structure observed between 200 and 500–600 km depth in body wave studies, but irresolvable with our long period datasets. Both anomalies point to a model in which several, possibly diachronous, plumes have risen to the surface to generate the Paraná large igneous province (LIP).     

Crustal structure from deep seismic soundings along the Koyna II (Kelsi-Loni) profile in the Deccan Trap area, India

The crustal depth section obtained from deep seismic soundings along the Koyna II (Kelsi-Loni) profile, which lies near latitude 18°N roughly in the east-west direction in that part of the Deccan Trap Maharashtra State, India, shows a number of reflection segments below the Deccan Traps down to the Moho discontinuity. A deep fault below the Deccan Traps 13 km east of Mahad divides the entire cross-section including the Moho boundary into two crustal blocks. The reflection segments show updip towards the west coast in the western block. The Moho discontinuity which is at a depth of 39 km near the deep fault starts rising towards the coast, reaching a depth of 31.5 km at the west coast. The eastern block is thrown up by 1.5 km with respect to the western block along the deep fault. A structural contour map of the Moho discontinuity for the Koyna reservoir area has been prepared from the present results and the crustal information obtained along the Koyna I profile (Kaila et al., 1979a), shows that the deep fault in the Koyna area is aligned in the NNW-SSE direction.Refraction seismic data analysis by the wave front method reveals that the thickness of the Deccan Trap increases towards the west coast. The Deccan Trap is 600–700 m thick in the eastern region between Nira (SP 130) and Loni (SP 200) and attains a thickness of 1500 m at 10 km east of the west coast. The longitudinal wave velocity in the Deccan Traps along the profile varies from 4.8 to 5.0 km/sec and in the crystalline basement from 6.0 to 6.15 km/sec. A tentative isopach contour map of the Deccan Traps and a tentative structural contour map of the Pre-Deccan Trap contact have been prepared for the Koyna reservoir area from the results along the Koyna II and Koyna I profiles. A flexure aligned in a NNW-SSE direction, in the Pre-Deccan Trap contact, which is an expression of the deep fault into the basement, has been clearly brought out. The flexure coincides in general with the orientation of the Deccan volcanic scarp in this area.     

Seismic refraction study of the continental edge off the eastern united states

Three long, strike-parallel, seismic-refraction profiles were made on the continental shelf edge, slope and upper rise off New Jersey during 1975. The shelf edge line lies along the axis of the East Coast Magnetic Anomaly (ECMA), while the continental rise line lies 80 km seaward of the shelf edge. Below the unconsolidated sediments (1.7–3.6 km/sec), high-velocity sedimentary rocks (4.2–6.2 km/sec) were found at depths of 2.6–8.2 km and are inferred to be cemented carbonates. Although multichannel seismic-reflection profiles and magnetic depth-to-source data predicted the top of oceanic basement at 6–8 km beneath the shelf edge and 10–11 km beneath the rise, no refracted events occurred as first arrivals from either oceanic basement (layer 2, approximately 5.5 km/ sec) or the upper oceanic crust (layer 3A, approximately 6.8 km/sec). Second arrivals from 10.5 km depth beneath the shelf edge are interpreted as events from a 5.9 km/sec refractor within igneous basement. Other refracted events from either layers 2 or 3A could not be resolved within the complex second arrivals. A well-defined crustal layer with a compressional velocity of 7.1–7.2 km/sec, which can be interpreted as oceanic layer 3B, occurred at 15.8 km depth beneath the shelf and 12.9 km beneath the upper rise. A well-reversed mantle velocity of 8.3 km/sec was measured at 18–22 km depth beneath the upper continental rise. Comparison with other deep-crustal profiles along the continental edge of the Atlantic margin off the United States, specifically in the inner magnetically quiet zone, indicates that the compressional wave velocities and layer depths determined on the U.S.G.S. profiles are very similar to those of nearby profiles. This suggests that the layers are continuous and that the interpretation of the oceanic layer 3B under the shelf edge east of New Jersey implies progradation of the shelf outward over the oceanic crust in that area. This agrees with magnetic anomaly evidence which shows the East Coast Magnetic Anomaly landward of the shelf edge off New Jersey and with previous seismic reflection data which reveal extensive outbuilding of the shelf edge during the Jurassic and Lower Cretaceous, probably by carbonate bank-margin accretion.     

3-D crustal structure of the extensional Granada Basin in the convergent boundary between the Eurasian and African plates

Three-dimensional P and S wave velocity models of the crust under the Granada Basin in Southern Spain are obtained with a spatial resolution of 5 km in the horizontal direction and 2 to 4 km in depth. We used a total of 15407 P and 13704 S wave high-quality arrival times from 2889 local earthquakes recorded by both permanent seismic networks and portable stations deployed in the area. The computed P and S wave velocities were used to obtain three-dimensional distributions of Poisson's ratio (σ) and the porosity parameter (V_p×V_s). The 3-D velocity images show strong lateral heterogeneities in the region. Significant velocity variations up to ±7% in P and S velocities are revealed in the crust below the Granada Basin. At shallow depth, high-velocity anomalies are generally associated with Mesozoic basement, while the low-velocity anomalies are related to the neogene sedimentary rocks. The south–southeastern part of the Granada Basin exhibits high σ values in the shallowest layers, which may be associated with saturated and unconsolidated sediments. In the same area, V_p×V_s is high outside the basin, indicating low porosity of the mesozoic basement. A low-velocity zone at 18-km depth is found and interpreted as a weak–ductile crust transition that is related to the cut-off depth of the seismic activity. In the lower crust, at 34-km depth, a clear slow V_p and V_s anomalous zone may indicate variations in lithology and/or with the rigidity of the lower crust rocks.     

Crustal and upper mantle S-wave velocity structure beneath the Bransfield Strait (West Antarctica) from regional surface wave tomography

Regional surface wave tomography in the sub-Antarctic Scotia Sea is helpful in revealing the nature of the crust and the S-wave seismic velocity profile beneath the Bransfield Strait. The joint use of our regional network, global seismographic network stations and local temporary arrays provide better lateral resolution than that obtained in our previous studies concerning the Scotia Sea region.Tomographic analysis of data obtained using 10 broad band seismic stations and more than 300 regional events, shows that the Bransfield Basin is characterised by a strong group velocity reduction of 8% with respect to the surrounding areas, in the period range from 15 s to 50 s.The crustal and upper mantle models of the eastern, central and western Bransfield Basin are obtained by joint inversion of Rayleigh and Love local dispersion curves from 15 s to 50 s. In addition our data set is expanded to a broader period interval (1–80 s), in central Bransfield Strait in order to better constrain the upper mantle and shallow crust.The main results can be summarized as follows: (a) the crust thins distinctly from W toward E; the variation is consistent with the type of volcanism, earthquake distribution and bathymetric observations, (b) low upper mantle velocities (soft lid) extend down to depths exceeding 70 km as a consequence of elevated temperatures, (c) the crust beneath the central Bransfield Basin displays continental characteristics with a gradually increasing S-wave velocity distribution versus depth analogous to the East African Rift structure of Kenya, (d) negative velocity gradients are present in the lower crust beneath the eastern Bransfield Basin; these could be interpreted as magmatic bodies originating from decompression melting of the mantle.     

On the P-wave velocity and plate-tectonics implications for the Tyrrhenian deep-earthquake zone

P-wave velocities in the Tyrrhenian mantle have been determined for the 230–480 km depth range. Analysis of P-wave travel times for a set of Tyrrhenian deep earthquakes gives a velocity-distribution law which shows different behaviours in the 230–300 km and 300–480 km depth intervals. For the first interval the velocity gradient is 0.64 · 10⁻² sec⁻¹ and for the second one it is 0.59 · 10⁻² sec⁻¹. At a depth of 300 km the velocity decreases rapidly from 8.75 to 8.43 km/sec.The results have been analyzed in the framework of a Tyrrhenian structural model characterized by a lithospheric slab dipping 55–60° in the WNW direction.It is also pointed out that the analysis of some geodynamic features of the slabs of Pacific island arcs carried out by Oliver et al. (1973) and Sleep (1973) can be applied to the Tyrrhenian mantle geodynamic features.     

Crustal structure of the Southern Alps beneath the intersection with the European Geotraverse

Newly digitized and amplitude controlled record sections from the 1977 Southern Alps refraction campaign permitted a reinterpretation of the crustal structure in the area between western Lombardy and the Giudicaria fault. The resulting model exhibits considerable lateral heterogeneity: in the west, below 7.5 km of sediments of the Lombardy Basin, the crust reaches a depth of only 31 km, whereas it thickens towards the more mountainous area in the east, reaching a depth of 46 km below the Adamello Massif. Although the signal character of the corresponding reflections is somewhat erratic, the data are satisfied best by models with a low-velocity zone in the upper crust. An additional small velocity discontinuity from 6.2 to 6.4 km/s was found in the middle crust at around 20 km. Earlier interpretations, based on travel-times alone, included a layer with a velocity of about 7 km/s at this depth. This high-velocity layer was then interpreted as lower-crustal material of the Adriatic — African plate, which had been overthrust onto the European plate during the Alpine orogeny, thus explaining the uplift of the Southern Alps. However, this model of crustal doubling is questionable, because such a mid-crustal high-velocity layer is not in agreement with the amplitude data. The relatively thin crystalline part of the crust under the Lombardy Basin is interpreted, in accordance with geological evidence, as a relic of a Late Hercynian rifting event.     

利用体波层析成像技术研究欧亚及邻区地幔三维速度结构

根据体波层析成像技术,利用大量走时数据,做出0°～180°E,30°S～90°S范围内0～2889km深的三维速度分布图像,得到欧亚地区局部区域岩石圈及地幔的高分辨率速度结构,并从地球动力学角度出发对这些成像结果做进一步解释。     

The lithosphere-asthenosphere system in Fennoscandia

We present a summary of the available information on Rayleigh-wave dispersion data for the Fennoscandian region. The observations have been combined to produce regional dispersion relations which have then been subjected to the “hedgehog” inversion procedure. The results are presented on a map outlining the thickness of the lid and the shear velocities in both the lid and the asthenosphere channel. Lid thickness up to around 135 km is found in the Bothnia-north-central Finland area with, if any, weak shear velocity contrast to the underlying layer. The surrounding areas are characterized by lid thickness up to around 75 km; a stronger low-velocity zone to lid contrast may be found in the Caledonian and Baltic Sea area (0.25÷0.45 km/s). Taking into account Moho depth data and the aforementioned results, a map of the lithosphere-asthenosphere system was derived.     

Structure of the crust and upper mantle in Canada

The seismic probing of the crust and upper mantle in Canada started in 1938 and since then has involved many government and university groups using a wide variety of techniques. These have included simple profiling with both wide and narrow station spacing, areal time-term surveys, detailed deep reflection experiments, very long-range refraction studies and the analysis of surface wave dispersion between stations of the Canadian Standard Network.

A review of the published interpretation leads to the general conclusion that:

1. (1) P_n-velocities vary from a value possibly as low as 7.7 km/sec under Vancouver Island to 8.6 km/sec and higher in the extreme eastern part of the shield and some parts of the Atlantic coast.

2. (2) Large areas of Canada have a crustal thickness of 30–40 km, with Vancouver Island, the southwestern Prairies, the Lake Superior basin and parts of the eastern shield of Quebec being thicker. No continental area in Canada is known to have a crust thinner than 29 km.

3. (3) The Riel discontinuity — a deep intra-crustal reflector and sometime refractor, is widely reported in the Prairies and Manitoba. It is not seen to the north in the vicinity of Great Slave Lake, nor in the Hudson Bay, Lake Superior and Maritime regions, nor in the interior of British Columbia. It may be present in some areas of the eastern shield.

4. (4) As experiments have become more detailed, crustal structures of greater complexity have been revealed. The concept that crustal structure becomes simpler with increasing depth is apparently unfounded.

Long-range refraction studies suggest that the Gutenberg P-wave low-velocity channel is poorly developed under the Canadian Shield. The analysis of the dispersion of surface waves, however, suggests that the channel is better developed for S-waves, and is present throughout the country. The lid of the channel is deepest under the central shield and shallowest under the Cordillera.     

The East African Rift System and the impact of orographic changes on regional climate and the resulting aridification

Several proxy data indicate an aridification of the East African climate during the Neogene, which might be influenced by the orographic changes of the East African Rift System (EARS) induced by tectonic forcing during the last 20 million years. To investigate the impact of the orography and especially of the rifts, the regional climate model CCLM is used, covering the EARS with Lake Victoria in the centre of the model domain. CCLM is driven by the ERA-Interim reanalysis and applied with a double-nesting method resulting in a very high spatial resolution of 7 km. The resolution clearly shows the shoulders and rifts of the western and eastern branch of the EARS and the Rwenzoris within the western branch. To analyse the orographic influence on climate, a new technique of modifying the orography is used in this sensitivity study. The shoulders of the branches are lowered and the rifts are elevated, resulting in a smoothed orography structure with less altitude difference between the shoulders and rifts. The changes in 2 m-temperature are very local and associated with the changes in the orography. The vertically integrated moisture transport is characterised by less vortices, and its zonal component is increased over the branches. The resulting amount of precipitation is mainly decreased west of the western branch and increased in the rift of the western branch. In the eastern branch, however, the changes in the amount of precipitation are not significant. The changes in the precipitation and temperature patterns lead to a shift of biomes towards a vegetation coverage characterised by more humid conditions in the northern part of the model domain and more arid conditions in the South. Thus, the aridification found in the proxy data can be attributed to the orographic changes of the rifts only in the northern model domain.     

S-wave velocity images of the Dead Sea Basin provided by ambient seismic noise

Based on passive seismic interferometry applied to ambient seismic noise recordings between station pairs belonging to a small-scale array, we have obtained shear wave velocity images of the uppermost materials that make up the Dead Sea Basin. We extracted empirical Green’s functions from cross-correlations of long-term recordings of continuous data, and measured inter-station Rayleigh wave group velocities from the daily correlation functions for positive and negative correlation time lags in the 0.1–0.5 Hz bandwidth. A tomographic inversion of the travel times estimated for each frequency is performed, allowing the laterally varying 3-D surface wave velocity structure below the array to be retrieved. Subsequently, the velocity-frequency curves are inverted to obtain S-wave velocity images of the study area as horizontal depth sections and longitude- and latitude-depth sections. The results, which are consistent with other previous ones, provide clear images of the local seismic velocity structure of the basin. Low shear velocities are dominant at shallow depths above 3.5 km, but even so a spit of land with a depth that does not exceed 4 km is identified as a salt diapir separating the low velocities associated with sedimentary infill on both sides of the Lisan Peninsula. The lack of low speeds at the sampling depth of 11.5 km implies that there are no sediments and therefore that the basement is near 10–11 km depth, but gradually decreasing from south to north. The results also highlight the bowl-shaped basin with poorly consolidated sedimentary materials accumulated in the central part of the basin. The structure of the western margin of the basin evidences a certain asymmetry both whether it is compared to the eastern margin and it is observed in north–south direction. Infill materials down to ∼8 km depth are observed in the hollow of the basin, unlike what happens in the north and south where they are spread beyond the western Dead Sea shore.