混合型缓冲回填材料膨胀力试验研究

与纯膨润土相比,混合型缓冲回填材料（膨润土与石英砂混合物）能够实现防渗阻隔能力、热传导性能、力学强度和可施工性能的最佳组合。选用高庙子钠基膨润土（GMZ001）为缓冲回填材料的主料,添加不同比例的石英砂,对掺砂比分别为0、10%、20%、30%、40%和50%的膨润土-砂混合物压实试样进行室内试验。结果表明,混合物的液限、塑限随掺砂率的增大而线性降低;膨胀力随时间呈指数增长。初始含水率较大时,最大膨胀力随初始含水率的增大略有降低。掺砂率一定时,最大膨胀力随初始干密度指数增长。提出了有效黏土密度的概念,建立了一定初始含水率条件下,任意掺砂率和初始干密度的高庙子膨润土-砂混合物最大膨胀力归一化模型,为混合型缓冲回填材料膨胀力的预测与控制提供了依据。     

Delineation of compaction criteria for acceptable hydraulic conductivity of lateritic soil-bentonite mixtures designed as landfill liners

In current geoenvironmental practice, design engineers usually require that soil liners in waste landfills be compacted within a specified range of water content and dry unit weight. This specification is based primarily on the need to achieve a minimum dry unit weight for factors controlling the performance of compacted soil liners most especially the hydraulic conductivity, k. In this study, lateritic soil treated with up to 10% bentonite, prepared at various compaction states (dry of optimum, optimum and wet of optimum moisture content) was compacted with four compactive efforts (i.e., the reduced British Standard Light, British Standard Light, West African Standard, and British Standard Heavy) to simulate the range of compaction energies expected in the field. Prepared soil mixtures were permeated with water and specimens that yielded the permissible limit of k????1?×?10^?9?m/s were enclosed in an envelope (known as the acceptable zone) on the water content?Cdry unit weight curve. It was observed that compaction conditions resulting in moisture content slightly wet of optimum led to the lowest values of k and that the shapes and boundaries of the acceptable zones gradually increased in extent, shifting to wet side of optimum moisture content as the bentonite content increased to 10%. This approach provides good control over the quality of compacted soils and has great potential for field application.     

Dynamic compaction properties of bentonite-based materials

Dynamic compaction tests of bentonite-based materials (BBMs) with 100, 70 and 50% bentonite contents have been performed using five powdery bentonites with different physicochemical properties to establish the simplified evaluation method for dynamic compaction properties of BBMs. For a given bentonite content and a total compaction energy condition, the maximum dry density, ρ_dmax, and the optimum water content, w_opt, which are well-known indexes of compaction properties, for BBMs were determined according to the type of bentonite used for BBMs. For evaluation of those values of BBMs derived in this study, the plastic limit of BBM, w_pbbm, was defined as the plastic limit that was measured using the sample pulverized to a maximum grain size of less than 425 μm in the case of BBM with sand having a maximum grain size of more than 425 μm and was measured using the powdery bentonite itself in the case of BBM without sand. This study proposed equations for evaluating ρ_dmax and w_opt of BBMs with more than 50% bentonite content under the total compaction energy conditions of 551–2755 kN-m/m³ using w_pbbm. Finally, we related the equations derived in this study to the equation for evaluating hydraulic properties of compacted BBMs proposed in previous work and proposed the preparation method of BBMs with more than 50% bentonite content for constructing BBM buffer by in-situ compaction method.     

An upscaling method and a numerical analysis of swelling/shrinking processes in a compacted bentonite/sand mixture

This paper presents an upscaling concept of swelling/shrinking processes of a compacted bentonite/sand mixture, which also applies to swelling of porous media in general. A constitutive approach for highly compacted bentonite/sand mixture is developed accordingly. The concept is based on the diffuse double layer theory and connects microstructural properties of the bentonite as well as chemical properties of the pore fluid with swelling potential. Main factors influencing the swelling potential of bentonite, i.e. variation of water content, dry density, chemical composition of pore fluid, as well as the microstructures and the amount of swelling minerals are taken into account. According to the proposed model, porosity is divided into interparticle and interlayer porosity. Swelling is the potential of interlayer porosity increase, which reveals itself as volume change in the case of free expansion, or turns to be swelling pressure in the case of constrained swelling. The constitutive equations for swelling/shrinking are implemented in the software GeoSys/RockFlow as a new chemo‐hydro‐mechanical model, which is able to simulate isothermal multiphase flow in bentonite. Details of the mathematical and numerical multiphase flow formulations, as well as the code implementation are described. The proposed model is verified using experimental data of tests on a highly compacted bentonite/sand mixture. Comparison of the 1D modelling results with the experimental data evidences the capability of the proposed model to satisfactorily predict free swelling of the material under investigation. Copyright © 2004 John Wiley & Sons, Ltd.     

Hydromechanical modelling of the SEALEX experiments

Numerical modelling of coupled physical processes in bentonite–sand mixtures under the geological conditions is significant for designing and constructing sealing systems in deep underground repositories for highly radioactive nuclear waste. Within the framework of DECOVALEX 2015, Task A, this work presents the model validation of OpenGeoSys by numerical modelling of coupled hydromechanical (HM) processes in bentonite–sand mixtures. Parameters used in the HM model were determined by modelling the laboratory tests of the sealing experiment (SEALEX). Afterwards these parameters were applied for the modelling of a small-scale mock-up test considering the influence of technological gap and incidental fail of the seal in the sealing system. In order to investigate the availability of employing these HM parameters and numerical models directly to field predictions, the modelling results and measured data of an in situ SEALEX experiment were analysed comparatively. The modelling results reproduced well the main features in HM behaviour of the compacted bentonite–sand mixture, which denotes that the adopted HM models and parameters are adequate for describing the HM processes in the sealing system. It is necessary to take the elastoplastic behaviour and evolution of the permeability of bentonite–sand mixtures into account when using the adopted models to reproduce the HM processes of a sealing system.     

Influence of Infiltration of Sodium Chloride Solutions on SWCC of Compacted Bentonite–Sand Specimens

The degree of saturation of compacted bentonite buffer in deep geological repositories is subject to alterations from infiltration of groundwater and heat emanated from the waste canisters. The matric suction (ψ)–degree of saturation (S _r ) relations of unsaturated clays is represented by soil–water characteristics curves (SWCC) that are influenced by soil structure, initial compaction condition and stress history. Infiltration of groundwater besides increasing the degree of saturation can also alter the pore water chemistry; the associated changes in cation hydration and diffuse double layer thickness could impact the micro-structure and matric suction values. This study examines the influence of infiltrating sodium chloride solutions (1,000–5,000 mg/L) on the transient ψ–S _r relations of compacted bentonite–sand specimens. Analysis of the ψ–S _r plots, and X-ray diffraction measurements indicated that infiltration of sodium chloride solutions has progressively less influence on the micro-structure and SWCC relations of bentonite–sand specimens compacted to increasingly higher dry densities. The micro-structure and SWCC relations of specimens compacted to 1.5 Mg/m³ were most affected, specimens compacted to 1.75 Mg/m³ were less affected, while specimens compacted to 2 Mg/m³ remained unaffected upon infiltration with sodium chloride solutions.     

Determination of hydraulic conductivity of sand-bentonite mixtures for engineering purposes

Pollution of the environment due to leakage from waste repositories is a well-known and wide spread problem. Emphasis has therefore been put on design of liners for such repositories, focusing on hydraulic conductivity and its variation with time, liner composition, water content, compaction etc. The paper addresses the hydraulic conductivity of sand/bentonite mixtures, especially the variation of the hydraulic conductivity as a function of bentonite content, compaction and degree of saturation. In order to better understand the variation of the hydraulic conductivity of a sand–bentonite mixture a new parameter k ₁ has been proposed. The parameter reflects the amount of bentonite per pore volume and can easily be calculated based on the amount of bentonite and the dry density of the soil mixture. Thereby, the hydraulic conductivity can be predicted as a function of different degres of compaction. This method can be used for engineering purposes to predict the hydraulic conductivity at an early stage of a design to get an idea of the required design and hence, cost.     

混合型缓冲回填材料膨胀变形试验研究

选用高庙子钠基膨润土(GMZ001)为缓冲回填材料的主料,添加不同比例的石英砂,对掺砂率分别为0%、10%、20%、30%、40%和50%的膨润土-砂混合物压实试样进行室内膨胀变形试验。结果表明：膨胀率随时间呈指数增长;掺砂率一定时,最大膨胀率随初始干密度的增大而线性增长;初始干密度一定时,最大膨胀率与掺砂率呈二次函数关系。引入有效黏土密度的概念对最大膨胀率进行计算,建立了任意掺砂率和初始干密度条件下膨润土-砂混合物最大膨胀率归一化模型,为混合型缓冲回填材料在高放废物地质处置中膨胀行为的预测与控制提供了依据。     

Effect of wetting–drying cycles on swelling behavior of lime stabilized sand–bentonite mixtures

In the present study, influence of wetting–drying cycles on swelling pressures of sand–bentonite mixtures used in the construction of sanitary landfills to have an impermeable liner was investigated before and after lime treatment of the mixtures. Swelling pressure tests were conducted to see if the swelling pressures were affected by wetting–drying cycles. First series of specimens were prepared as a mixture of sand and bentonite only. In the first series of specimens, sand was mixed with bentonite in various proportions with their optimum water contents and compacted by using standard proctor energy. In the second series of the specimens, lime in various proportions was added to the mixtures of sand–bentonite. Then, the sand–bentonite mixtures stabilized by lime were compacted with the standard proctor energy at their optimum moisture contents. Five wetting–drying cycles were performed on each specimen and values of swelling pressures were measured at the end of each cycle. Results of swelling pressure tests indicated that the swelling pressure is decreased when lime is added to the mixtures. In addition, decrements were observed on swelling pressures by wetting–drying cycles. The results of the experiments of this investigation showed that the beneficial effect of lime stabilization to control the swelling pressures was partly lost by the wetting–drying cycles. However, the test results indicated that the swelling pressures of the specimens made of sand–bentonite mixtures stabilized by lime were lower than the swelling pressures of the specimens made of only sand–bentonite mixtures.     

砂-膨润土混合屏障材料渗透性影响因素研究

膨润土因具有渗透性低、阳离子交换能力高等优点被认为是最适合高放废物深地质处置库中屏障系统的缓冲材料,工程实践发现随着水化过程的进行,纯高压实膨润土强度不断降低,并最终影响到工程屏障系统功能的发挥。针对这一问题,在膨润土中加入一定比例的石英砂,可以有效地提高工程屏障的热传导特性、压实性、力学强度和长期稳定性,降低工程造价。本文研究了影响砂-膨润土混合物渗透性的主要因素,包括膨润土含量、粒径分布、含水量和干密度、压实方法以及膨润土类型等。结果表明,砂土混合物渗透性主要受膨润土的渗透性控制,渗透系数随着膨润土含量和干密度的增加而减小,当膨润土含量超过某一界限值后,继续增加膨润土含量对降低渗透系数的作用有限;细颗粒和级配良好的混合物渗透系数小,当土体内部发生渗透侵蚀将增大渗透系数;最优含水量条件下压实得到的渗透系数最低,高于最优含水量压实得到的渗透系数比低于最优含水量压实得到的渗透系数要小。     

缓冲／回填材料——砂-膨润土混合物研究进展

砂-膨润土混合物已被很多核能国家选为核废物地质处置库中理想的缓冲/回填材料。膨润土中加入砂可提高热传导系数和强度,维持适当的膨胀力,使其工程上易于处理并节省成本;但同时会导致其阻水能力和自愈性减弱。研究表明,影响砂-膨润土混合物以上各性质的主要因素为：砂/膨润土配合比、初始含水量、干密度等,它们综合决定着砂/膨润土最优配合比的选取。石英砂对混合物的渗透性、热传导性、强度等的影响,最优配合比选取,以及非饱和状态下吸力变化对混合物渗透性的影响等,应该是今后一段时间内砂-膨润土混合物研究的重点。     

Models of compacted fine-grained soils used as mineral liner for solid waste

To prevent the leakage of pollutant liquids into groundwater and sublayers, the compacted fine-grained soils are commonly utilized as mineral liners or a sealing system constructed under municipal solid waste and other containment hazardous materials. This study presents the correlation equations of the compaction parameters required for construction of a mineral liner system. The determination of the characteristic compaction parameters, maximum dry unit weight (γ _dmax) and optimum water content (w _opt) requires considerable time and great effort. In this study, empirical models are described and examined to find which of the index properties correlate well with the compaction characteristics for estimating γ _dmax and w _opt of fine-grained soils at the standard compactive effort. The compaction data are correlated with different combinations of gravel content (G), sand content (S), fine-grained content (FC = clay + silt), plasticity index (I _p), liquid limit (w _L) and plastic limit (w _P) by performing multilinear regression (MLR) analyses. The obtained correlations with statistical parameters are presented and compared with the previous studies. It is found that the maximum dry unit weight and optimum water content have a considerably good correlation with plastic limit in comparison with liquid limit and plasticity index.     

A new approach for stabilization of lateritic soil with Portland cement and sand: strength and durability

The presence of lateritic soils occurs in tropical and subtropical regions. The improvement of lateritic soils that are not suitable for a particular purpose through techniques that combine modification of grain size through the insertion of sand, incorporation of Portland cement and densification through compaction is seen as an alternative. In this context, a dosage method to use a local lateritic soil as construction material in a most rational way reducing the economic and environmental impacts related to this activity is still missing. Therefore, the current research aims to evaluate the performance of a lateritic soil via modification of grain size through the insertion of sand, incorporation of Portland cement and densification through compaction. For this, unconfined compression, and durability (wetting and drying) tests were carried out on specimens of compacted clayey gravel lateritic soil, whose granulometry was modified by the insertion of distinct amounts (from zero to 45%) of weathered sand, treated with distinct Portland cement contents (from 4 to 10%), molded at different dry unit weights (from 16.8 to 20.1 kN/m³) and cured for 7 and 28 days. Results of the mechanical tests have shown the significant influence exerted by cement content and dry unit weight of the blend, followed by curing time and finally sand insertion. Satisfactory correlations between the response variables (q_u and ALM) and the adjusted porosity/cement index (η/C_v) were obtained. Furthermore, an innovative approach to replacing the laborious durability test is proposed.

     

掺绿砂改良膨胀土室内试验研究

绿砂高额的处理费用与其具有的再利用潜力相比,使绿砂再利用的研究得到重视,尤其对公路路基改良具有很大的利用潜力。针对膨胀土路基的胀缩问题,围绕绿砂及膨胀土-绿砂混合物进行一系列室内土工试验,探讨绿砂作为公路膨胀土路基改良剂的可行性。在不同含水率及不同配比条件下,对绿砂以及绿砂改良后膨胀土的基本物理性质、击实特性、力学特性等进行室内对比试验分析。分析结果表明,绿砂改良膨胀土试样的强度主要取决于试样的含水率、掺砂率;随着掺砂率的增加,塑性指数逐渐降低,最佳含水率也随之减小,最大干密度增大的幅度变化很小,无侧限抗压强度先降低而后提高,其后又降低。     

Effects of compaction moisture content on the shear strength of an unsaturated clay

This paper deals with the results of an experimental study carried out on compacted clay (PL=23%) to investigate the influence of compaction water content on the shear strength of the clay. For the measurement of shear strength parameters, direct shear tests were done on samples compacted at optimum moisture content (i.e. w=24%), at the dry side of optimum (i.e. w=18%, 20% and 22%) and at the wet side of optimum (i.e. w=26% and 28%). Thermocouple psychrometers were used for suction measurements and the suction-moisture content relationship of the soil sample was obtained. The trends for suction, angle of friction and cohesion, which change below and above optimum moisture content, were analyzed. The compacted clay behaves like a granular soil on the dry side of optimum water content; and a reduction in angle of friction and an increase in cohesion are observed as the compaction water contents approach the optimum value. The angle of friction is not affected by soaking, but after soaking cohesion of the sample reduces. This revised version was published online in July 2006 with corrections to the Cover Date.     

Effects of Post-compaction Residual Lateral Stress and Electrolyte Concentration on Swelling Pressures of a Compacted Bentonite

The effects of post-compaction residual lateral stress and salt concentration in the hydrating fluid on swelling pressures of compacted MX80 bentonite is brought out in this paper. In order to release the residual lateral stresses, following the static compaction process during preparation of specimens, compacted bentonite specimens were extruded from the specimen rings and then inserted back prior to testing them for swelling pressures in isochoric condition. The swelling pressure tests were carried out at several dry densities of the bentonite with distilled water and solutions of NaCl (0.1 and 1.0 M) as the hydrating fluids. With water, the test results showed that specimens that underwent extrusion and insertion processes exhibited about 10–15 % greater swelling pressures as compared to the specimens those that were compacted and tested. The influence of saline solutions was found to reduce the swelling pressure of the bentonite, but their impact was less significant at high compaction dry densities.     

Shrinkage and desiccation cracking in bentonite–sand landfill liners

Data are reported on the shrinkage and desiccation cracking exhibited by bentonite-enhanced sand mixtures (BES) upon air-drying. Mixtures containing 10 and 20% bentonite by dry weight, compacted at moisture contents ranging from 8 to 32%, were investigated. Hydraulic conductivity data for BES specimens saturated and tested immediately after compaction, and for similar specimens that had no visible damage after air-drying, are also presented.

All the mixtures exhibited volumetric shrinkage upon air-drying with the amount of shrinkage increasing with increasing moisture content during compaction. At any initial moisture content mixtures containing 20% bentonite shrink more than those containing 10% bentonite, but the shrinkage is insensitive to the compactive effort. Compacted beds of BES containing 10 and 20% bentonite exhibit no visible desiccation cracking as the top surface is dried when compacted at 15 and 14% moisture content, respectively, and only minor cracking when compacted at initial moisture contents of 20 and 15%, respectively. For the range of mixtures tested, it appears that cracking only occurs when BES undergoes more than about 4% volumetric shrinkage when air-dried. The saturated hydraulic conductivity of intact BES specimens is unaffected by a drying episode prior to testing.     

Performance evaluation of soil mixtures treated with graphite and used as barrier fill material for high-level radioactive waste repository

Buffer/backfill material is an important engineering barrier in a deep geological repository of high-level radioactive waste (HLW). Its thermo-hydro-mechanical (THM) performance is very important for the safe and stable operation of the HLW repository system. Natural graphite powder mixed with sodium bentonite forms a buffer/backfill material that can dissipate heat quickly and provide strong isolation. In this paper, the THM characteristics of bentonite–sand–graphite–polypropylene fiber (BSGF) mixtures, used as a buffer/backfill material, were studied through a series of laboratory tests. The influence of graphite and polypropylene fiber contents on thermal conductivity, swelling pressure, hydraulic conductivity, and strength properties of BSGF mixtures with different sand contents was analyzed. Experimental results indicated that the graphite content, the maximum graphite mesh number, and the initial dry density of bentonite–graphite mixtures influenced the thermal conductivity of bentonite–graphite mixtures. The addition of polypropylene fiber was found to enhance the shear strength and inhibit cracking without significantly affecting the expansivity, permeability, and thermal conductivity of the BSGF mixtures. This study provides a new buffer/backfill material that can improve the stability, functionality, and thermal efficiency of the HLW repository.