Variability of bedload transport and channel morphology in a braided river hydraulic model

This paper investigates variability in bedload transport and channel morphology for 11 replicate experimental runs in an approximately 1:50 braided river model. The experiments, each of 90 h duration, were carried out in a 20 × 3m tilting flume. All the experiments started with the same initial conditions. Bedload transport was measured at 5 min intervals in a collection drum at the exit from the flume. The model showed reasonable hydraulic similarity when compared to prototype rivers. Results show that mean bedload transport rates for the 11 runs vary in the range 0·98 to 1·49gs^?1 (mean + 1·21, coefficient of variation 11 per cent). Within-run transport rates commonly vary from close to zero, to two and occasionally three or four times the mean rate. Within the bedload series, several irregular phases of transport intensity can be observed, but time series analysis of the data show little underlying serial structure (an AR(2) autoregressive model is appropriate). Channel patterns are narrow/braided, are established quickly and remain relatively stable throughout the runs, although channel widths increase between 20 and 103 per cent over the 11 runs. Channel behaviour varies from aggradational to transitional between aggradation and degradation. Time-averaged bedload transport rate is weakly correlated with braiding intensity. In general, these results demonstrate that for a given set of controlling variables, bedload transport and channel morphology can be approximately replicated.     

Assessment of intermediate fine sediment storage in a braided river reach (southern French Prealps)

This paper presents a field investigation on river channel storage of fine sediments in an unglaciated braided river, the Bès River, located in a mountainous region in the southern French Prealps. Braided rivers transport a very large quantity of bedload and suspended sediment load because they are generally located in the vicinity of highly erosive hillslopes. Consequently, these rivers play an important role because they supply and control the sediment load of the entire downstream fluvial network. Field measurements and aerial photograph analyses were considered together to evaluate the variability of fine sediment quantity stored in a 2·5‐km‐long river reach. This study found very large quantities of fine sediment stored in this reach: 1100 t per unit depth (1 dm). Given that this reach accounts for 17% of the braided channel surface area of the river basin, the quantities of fine sediment stored in the river network were found to be approximately 80% of the mean annual suspended sediment yields (SSYs) (66 200 t year^?1), comparable to the SSYs at the flood event scale: from 1000 t to 12 000 t depending on the flood event magnitude. These results could explain the clockwise hysteretic relationships between suspended sediment concentrations and discharges for 80% of floods. This pattern is associated with the rapid availability of the fine sediments stored in the river channel. This study shows the need to focus on not only the mechanisms of fine sediment production from hillslope erosion but also the spatiotemporal dynamics of fine sediment transfer in braided rivers. Copyright © 2010 John Wiley & Sons, Ltd.     

Impacts of sediment retention by dams on delta shoreline recession: evidences from the Krishna and Godavari deltas,India

River deltas are the major repositories of terrestrial sediment flux into the world's oceans. Reduction in riverine inputs into the deltas due to upstream damming might lead to a relative dominance of waves, tides and currents that are especially exacerbated by coastal subsidence and sea‐level rise ultimately affecting the delta environment. Analysis of multi‐date satellite imagery and maps covering the Krishna and Godavari deltas along the east coast of India revealed a net erosion of 76 km² area along the entire 336‐km‐long twin delta coast during the past 43 years (1965–2008) with a progressively increasing rate from 1·39 km² yr^?1 between 1965 and 1990, to 2·32 km² yr^?1 during 1990–2000 and more or less sustained at 2·25 km² yr^?1 during 2000–2008. At present the Krishna has almost become a closed basin with decreased water discharges into the delta from 61·88 km³ during 1951–1959 to 11·82 km³ by 2000–2008; and the suspended sediment loads from 9 million tons during 1966–1969 to as low as 0·4 million tons by 2000–2005. In the case of the Godavari delta, although the water discharge data do not show any major change, there was almost a three‐fold reduction in its suspended sediment loads from 150·2 million tons during 1970–1979 to 57·2 million tons by 2000–2006. A comparison of data on annual sediment loads recorded along the Krishna and Godavari Rivers showed consistently lower sediment quantities at the locations downstream of dams than at their upstream counterparts. Reports based on bathymetric surveys revealed considerable reduction in the storage capacities of reservoirs behind such dams. Apparently sediment retention at the dams is the main reason for the pronounced coastal erosion along the Krishna and Godavari deltas during the past four decades, which is coeval to the hectic dam construction activity in these river basins. Copyright © 2010 John Wiley and Sons, Ltd.     

Field observations on hyperconcentrated flows in mountain torrents

Field observations on hydraulics and sediment dynamics during extreme floods in two mountain torrents show the influence of man-made constructions such as bridges and check dams, in addition to the sediment supplied naturally by the basin and the channel network, on the formation of hyperconcentrated flows. In the Pyrenean Arás basin, hyperconcentrated flow occurred after collapse of a bridge, which in turn mobilized large volumes of sediment from the stream channel and, subsequently, destroyed a series of check dams. Boulders up to several metres in size were transported in a mixture of sand and fine material. A minimum of 100000 tonnes of sediment were deposited on the alluvial fan during the event. Prior to bridge destruction, mean bedload transport rates had reached 0.4t m⁻¹ s⁻¹ upstream. In the alpine Lainbach basin, the flood was characterized by transportation of large amounts of slope material, including debris flows. Along its main tributary an intensive hyperconcentrated flow occurred during the rising stage, whereas in the main valley smaller flows occurred after failure of check dams. The depth of coarse material deposited reached 80 cm. The effectiveness of the Aràs and Lainbach floods was attained due to exceptional rates of energy expediture. Flood power ranged from 20000 W m⁻² to 40000 W m⁻² on average. Copyright © 1999 John Wiley & Sons, Ltd.     

Reach-scale suspended sediment balance downstream from dams in a large Mediterranean river

Abstract

This paper presents a reach-scale sediment balance of a large impounded Mediterranean river (the lower Ebro, 1998–2008). Multi-temporal sediment storage and the influence of floods and tributaries on the sediment load were examined using continuous discharge and turbidity records. The mean annual suspended sediment load at the reach outlet (Xerta) is 0.12?×?10⁶ t, corroborating previous results. Suspended sediment concentrations were low (SSC_mean?=?13 mg L^-1), attaining a maximum of 274 mg L^-1. Erosion processes (channel-scour, bank erosion) are dominant, and net export of sediment occurs over the long term. Unexpectedly, ephemeral tributaries were found to contribute significantly: sediment delivered during torrential events attained 5% of the Ebro annual load, and was even larger than that in flushing flows. Overall, most of the suspended sediment load is transported by floods (up to 65% in some years). The results constitute basic information to underpin current management actions aiming to achieve the sustainability of the riverine and deltaic system.

Editor D. Koutsoyiannis; Associate editor D. Hughes

Citation Tena, A., Batalla, R.J. and Vericat, D., 2012. Reach-scale suspended sediment balance downstream from dams in a large Mediterranean river. Hydrological Sciences Journal, 57 (5), 831–849.     

The impact of pro‐glacial lakes on downstream sediment delivery in Norway

Glacier recessions caused by climate change may uncover pro‐glacial lakes that form important sedimentation basins regulating the downstream sediment delivery. The impact of modern pro‐glacial lakes on fluvial sediment transport from three different Norwegian glaciers: Nigardsbreen, Engabreen and Tunsbergdalsbreen, and their long‐term development has been studied. All of these lakes developed in modern times in overdeepened bedrock basins. The recession of Nigardsbreen uncovered a 1.8 km long and on average 15 m deep pro‐glacial lake basin during 1937 to 1968. Since then the glacier front has been situated entirely on land, and the sediment input and output of the lake has been measured. The suspended sediment transport into and out of the lake averaged 11 730 t yr^?1 and 2340 t yr^?1 respectively. Thus, 20% remained in suspension at the outlet. The measured mean annual bedload supplied to the lake was 11 800 t yr^?1, giving a total transport of 23 530 t yr^?1 which corresponds to a specific sediment yield of 561 t km^?2 yr^?1. A 1.9 km long and up to 90 m deep pro‐glacial lake basin downstream from Engabreen glacier was uncovered during 1890 to 1944. The average suspended sediment load delivered from the glacier during the years 1970–1981 amounted to 12 375 t yr^?1and the transport out of the lake was 2021 t yr^?1, giving an average of 16% remaining in suspension. The mean annual bedload was 8000 t yr^?1, thus the total transport was 20 375 t yr^?1, giving a specific sediment yield of 566 t km^?2 yr^?1. For Tunsbergdalsbreen glacier, measurements in the early 1970s indicated that the suspended sediment transport was on average 44 000 t yr^?1. From 1987 to 1993 the recession of the glacier uncovered a small pro‐glacial lake, 0.3 km long and around 9 m deep. Downstream from this, the suspended sediment load measured in 2009 was 28 000 t yr^?1, indicating that as much as 64% remained in suspension. Flow velocity, grain size of sediment, and morphology of the lake are important factors controlling the sedimentation rate in the pro‐glacial lakes. A survey of the sub‐glacial morphology of Tunsbergdalsbreen revealed that there are several overdeepened basins beneath the glacier. The largest is 4 km long and 100 m deep. When the glacier melts back they will become lakes and act as sedimentation basins. Despite an expected increase in sediment yield from the glacier, little sediment will pass these lakes and downstream sediment delivery will be reduced markedly. Beneath Nigardsbreen there was only a small depression that may form a lake and the sediment delivery will not be significantly affected. © 2014 The Authors. Earth Surface Processes and Landforms published by John Wiley & Sons Ltd.     

Sediment transport in an alpine river before and after a dambreak flood event

Fluvial sediment transport in the high mountain Partnach River (Reintal Valley, Bavarian Alps) was investigated during a 10‐year observation period (2001–2010). During this period, the downstream reach of the Partnach River was decoupled from upstream sediment throughput by a rockslide deposit until 2005. In August 2005, the dam was partially breached during a flood event resulting in renewed sediment coupling between the upstream and downstream reaches. A comparison of pre‐ and post‐dambreak river sediment load data showed that the dissolved load dominated sediment transport prior to August 2005 with a switch to the dominance of bedload transport, post‐dambreak. The higher post‐dambreak bedload rates were particularly evident during the first years after the dam failure due to significant coarse material coupling between active sediment sources (undercut banks/talus cones) and the Partnach River. In the last years of the observation period (2009 and 2010) the dominance of dissolved load transport was re‐established. Copyright © 2011 John Wiley & Sons, Ltd.     

Meso‐scale catchment sediment budgets: combining field surveys and modeling in the Dragonja catchment,southwest Slovenia

In this paper, we present a methodology to construct a sediment budget for meso‐scale catchments. We combine extensive field surveys and expert knowledge of the catchment with a sediment delivery model. The meso‐scale Mediterranean drainage basin of the Dragonja (91 km²), southwest Slovenia, was chosen as case study area. During the field surveys, sheet wash was observed on sloping agricultural fields during numerous rainfall events, which was found to be the main source of sediment. With the sediment yield model WATEM/SEDEM the estimated net erosion on the hillslopes 4·1 t ha^–1 y^–1 (91% of inputs). The second source, bank erosion (4·2%; 0·25 t ha^–1 y^–1) was monitored during several years with erosion pins and photogrammetric techniques. The last source, channel incision, was derived from geomorphological mapping and lichenomery and provided 3·8% (0·17 t ha^–1 y^–1) of the sediment input. The river transports its suspended sediment mainly during high‐flow events (sampled with automated water samplers). About 27% (1·2 t ha^–1 y^–1) of the sediment delivered to the channel is deposited on floodplains and low terraces downstream (estimated with geomorphological mapping, coring and cesium‐137 measurements). The sediment transported as bedload disintegrates during transport to the outlet due to the softness of the bedrock material. As a result, the river carries no bedload when it reaches the sea. The results imply a build‐up of sediment in the valleys catchment. However, extreme flood events may flush large amounts of sediment stored in the lower parts of the system. Geomorphological evidence exists in the catchment that such high magnitude, low frequency events have happened in the past. Copyright © 2009 John Wiley & Sons, Ltd.     

A two-dimensional model for suspended sediment transport in the southern branch of the Rhine–Meuse estuary,The Netherlands

For the southern branch of the Rhine–Meuse estuary, The Netherlands, a two-dimensional horizontal suspended sediment transport model was constructed in order to evaluate the complicated water quality management of the area. The data needed to calibrate the model were collected during a special field survey at high river runoff utilizing a number of techniques: (1) turbidity probes were used to obtain suspended sediment concentration profiles; (2) air-borne remote sensing video recordings were applied in order to obtain information concerning the spatial distribution of the suspended sediment concentration; (3) an acoustic probe (ISAC) was used to measure cohesive bed density profiles and (4) an in situ underwater video camera (VIS) was deployed to collect video recordings of the suspended sediment. These VIS data were finally processed to fall velocity and diameter distributions and were mainly used to improve insight into the relevant transport processes, indicating significant erosion of sand from the upstream Rhine branch. For quantitative calibration of the model, the data from the turbidity profiles were used. Sedimentation and erosion were modelled according to Krone and Partheniades. The model results showed a good overall fit to the measurements, with a mean absolute error of 18 per cent (standard fault = 1 per cent), corresponding to concentrations of about 0·020 (upstream) to 0·005 kg m⁻³ (downstream). The overall correlation between observed and simulated suspended sediment concentrations was 0·85. The remote sensing video recordings were used for a qualitative calibration of the model. The distribution pattern of the suspended sediment on these photos was reproduced quite well by the model. However, a more accurate calibration technique is needed to enable the use of aerial remote sensing as a quantitative calibration method. Copyright © 1999 John Wiley & Sons, Ltd.     

Response of the Ohau River and delta to lake level lowering

The response of the Ohau River to a lowering of Lake Benmore of 4 m was monitored during a three-month period when the river was carrying mean daily flows between 100 and 400 m³/s from a power station. Initially, the river degraded by up to 0·8 m for a distance of 1·3 km upstream from the lake, but during the 52-day period of minimum lake level, the delta and lower channel aggraded by up to 0·4 m. During that period, an estimated 225 000 m³ of sediment was supplied to the delta, sufficient for rapid progradation of the delta front into the shallow lake and the observed aggradation of the channel and delta surface. Other factors, in this case receiving-basin geometry and sediment yield, may thus control the response of a river-delta system to relative base-level lowering.     

The impact of agriculture on solute and suspended sediment load on a Mediterranean watershed after intense rainstorms

The solute and suspended‐sediment load following five rainstorms (2005–2007) with varied intensities were studied at the Vernegà experimental watershed, north‐western Spain. Two land‐use areas are located within this watershed, the upstream one (forest) with 160 ha a 100% forested area, and the downstream one (agricultural) with 97 ha being 9 ha conventional agricultural field and 88 ha forest. This study investigates the capacity of each land‐use to yield water, suspended sediment concentration (SSC) and dissolved solid concentration (DSC). The hypothesis is that DSC and SSC from the agricultural area are greater than DSC and SSC of the forest area. Results showed that the agriculture area produced significantly greater mean DSC than in the forest area, the main contribution was the Ca²⁺ (24·68 ± 46·52 mg l^?1) ion at the agricultural area. A long‐term sediment production rate at the agricultural outlet was calculated (69·1 tonnes per 100 years) based on the total sediment discharge (TSD) and the recurrence interval of the largest event of the five rainstorms (October 2005). Geographic information system (GIS) spatial data layers of the watershed were produced to determine the relation of tracks, landforms, slopes and forest management to SSC yield in the forest outlet (133·89 ± 308·14 mg l^?1) during the five rainstorms. Agriculture practices are the main cause of soil erosion at the study area. Copyright © 2010 John Wiley & Sons, Ltd.     

The anatomy of effective discharge: the dynamics of coarse sediment transport revealed using continuous bedload monitoring in a gravel‐bed river during a very wet year

Indirect, passive approaches for monitoring coarse bedload transport could allow cheaper, safer, higher‐resolution, longer‐term data that revolutionises bedload understanding and informs river management. Here, insights provided by seismic impact plates in a downstream reach of a flashy gravel‐bed river (River Avon, Devon, UK) are explored in the context of plate performance. Monitoring of a centrally‐situated plate (IP1) during an extremely wet 12‐month period demonstrated that impacts were related to discharge as a measure of transport potential (R² = 0.38) but that factors other than transport limitations are important. Analysis of discrete flow events revealed consistent rising‐limb and falling‐limb impact spikes biased toward the latter for larger events. Such patterns may result from disruption of the upstream armour layer (rising limb) and supply enhancements related to both upstream mass bank failures and/or flood routing of non‐local sediment sources (falling limb). Installation of additional impact plates indicated that plate IP1 was indeed dominantly related to instantaneous discharge, that a three‐plate lateral array somewhat better explained impact variability (R² = 0.49), and that the bedload track shifts laterally with discharge. Aggregating event‐total IP1 impacts against volumetric discharge further increases explanation as intra‐event and stochastic bedload factors are subsumed but left 26% unexplained variance related to the unsampled bedload mass, inter‐event supply differences, and attributes of plate performance. Annualising the data created an impact‐based 'effective discharge’ for this extremely wet year that was closer to morphological bar‐full in magnitude than bankfull, but the preceding results imply this outcome is related as much to supply limitations as transport limitations. Overall, passive approaches offer a liberating prospect for bedload monitoring, capable of producing insights only achievable through high resolution, extended time periods. Such results could potentially inform threshold conditions and geomorphological effectiveness of flows for future river management strategies. Copyright © 2015 John Wiley & Sons, Ltd.     

The Ganges and Brahmaputra rivers in Bangladesh: basin denudation and sedimentation

Every year the Ganges and Brahmaputra rivers in Bangladesh transport 316 and 721 million tonnes of sediment, respectively. These high loads of suspended sediment reflect the very high rate of denudation in their drainage basins. The average mechanical denudation rate for the Ganges and Brahmaputra basins together is 365 mm 10³ yr⁻¹. However, the rate is higher in the Brahmaputra Basin than that in the Ganges Basin. Several factors, including mean trunk channel gradient, relief ratio, runoff, basin lithology and recurring earthquakes are responsible for these high denudation rates. Of the total suspended sediment load (i.e. 1037 million tonnes) transported by these rivers, only 525 million tonnes (c. 51% of the total load) are delivered to the coastal area of Bangladesh and the remaining 512 million tonnes are deposited within the lower basin, offsetting the subsidence. Of the deposited load, about 289 million tonnes (about 28% of the total load) are deposited on the floodplains of these rivers. The remaining 223 million tonnes (about 21% of the total load) are deposited within the river channels, resulting in aggradation of the channel bed at an average rate of about 3·9 cm yr⁻¹. Although the Brahmaputra transports a higher sediment load than the Ganges, the channel bed aggradation rate is much higher for the Ganges. This study also documents a wide range of interannual, seasonal and daily variation in suspended sediment transport and water discharge. Interannual variation in sediment deposition within the basin is also suggested. Copyright © 1999 John Wiley & Sons, Ltd.     

Sediment yield and transport process assessment from reservoir monitoring in a semi‐arid mountainous river

Soil loss, fluvial erosion, and sedimentation are major problems in semi‐arid environments due to the high associated costs of decreasing services such as provisioning and regulating water resources. The objective of this research is to analyse sediment yield in a mountainous semi‐arid basin, paying special attention to the sources of sediment, the associated uncertainties, and the transport processes involved. The segregation hypothesis along a reservoir of the sediment coming from hillslopes or fluvial systems is also evaluated. For this purpose, bottom‐set and deltaic deposits of a reservoir (110 hm³ ) in southern Spain have been measured and compared with basin erosion and fluvial transport monitoring over a 12‐year period. The volume of sediment stored at the bottomset of the reservoir shows a relative match with parametric predictions based on the Revised Universal Soil Loss Equation/Modified Universal Soil Loss Equation hillslope models and rating curves, estimated as being between 7 and 13 t·ha^?1·year^?1. Similarly, the measured volume of deltaic deposit fits the average value of stochastic simulations from different bedload transport equations. These contributions represent 50–65% of the total volume measured regarding suspended sediment inputs, way above that described in previous works. This highlights the importance of considering bedload when estimating the useful life of reservoirs in semi‐arid environments. The major differences in sediment grain size between hillslopes and river systems, and the size fractions measured along the reservoir, support the assertion of segregation hypothesis. Nonetheless, based on the processes observed and the uncertainty related to modelling, that assertion has to be taken with caution. At basin scale, a specific sediment yield of between 19 and 24 t·ha^?1·year^?1 has been estimated, which includes hillslopes and fluvial contributions. This rate is in the range of sediment yield reported for Mediterranean mountain areas of a torrential character. The pulse‐like nature of the system and the spatial heterogeneity of fluvial and hillslope erosion rates points out the importance of considering mid to long‐term and process‐based approaches and emphasizes the limitations of annual estimations for management purposes.     

The nature and transport of the fine‐grained component of Swift Creek Landslide,Northwest Washington

Extreme sedimentation in Swift Creek, located in the Cascades foothills in NW Washington (48°55′N, 122°16′W), results from erosion of the oversteepened, unvegetated toe of a large (55 hectares) active landslide. Deposition of landslide‐derived sediment has necessitated costly mitigation projects in the channel including annual dredging and temporary sediment traps in an attempt to reduce the risk of flooding and damage to man‐made structures downstream. This study attempts to understand the process of sediment production along with the corresponding erosion rates of the sediment source to help with the development of mitigation plans and construction of optimal sediment reservoirs. The bedload and suspended sediment in the creek are a direct result of the weathering process of the serpentinitic bedrock underlying the landslide. The serpentinite does not weather to smectite clay, as previously thought. Instead, it weathers to asbestiform chrysotile with minor amounts of chlorite, illite and hydrotalcite, all of which occur in clay seeps on the unvegetated surface of the landslide. The chrysotile fibers average 2 µm in length and make up at least 50%, by volume, of the suspended load transported in Swift Creek. This study does not address the environmental or health implications of the asbestiform chrysotile transport or deposition. During the sampled time between February 2005 and February 2006, 127 discrete suspended sediment samples were collected and discharge was measured 66 times. The suspended sediment concentrations ranged from 0·02 g L^?1 to 41·6 g L^?1 and the discharge ranged from 0·0 m³ s^?1 to 0·5 m³ s^?1. A nonlinear functional model estimated the total suspended sediment flux from detailed precipitation records and discrete suspended sediment concentration and discharge measurements to be 910 t km^?2 yr^?1. When the suspended sediment flux is coupled with estimates of downstream deposition of coarse sediment, the estimated erosion rate for the entire Swift Creek landslide is 158 mm yr^?1. The majority of the material entering Swift Creek is presumed to originate on the unvegetated toe of the landslide, for which the erosion rate is thus approximately 1 m yr^?1. Copyright © 2010 John Wiley & Sons, Ltd.     

Uranium and thorium isotopes in the rivers of the Amazonian basin: hydrology and weathering processes

Two expeditions (October 1989 and May 1992) were carried out to two points of the main Amazon River channel and four tributaries. The Solimões and Madeira rivers, taking their origin in the Andes, are whitewater rivers. The Negro River is a typical acid, blackwater river. The Trombetas River flows through bauxite‐rich areas, and is characterized by low concentrations of dissolved humic substances. The ²³⁸U, ²³⁴U, ²³²Th and ²³⁰Th activities were recorded from dissolved, suspended particulate phases and river bank sediments. The latter were analysed for their ²²⁶Ra, ²²⁸Ra and ²¹⁰Pb contents, and also subjected to leaching with 0·2 M hydroxylamine–hydrochloride solution to determine the concentrations of radionuclides bound to amorphous Fe hydroxides and Mn oxides and hydroxides. The dissolved U average concentration in the Amazon system is ten times lower than the mean world river concentration. The uranium concentration observed at Óbidos in the lower Amazon (0·095 µg L^?1), where the U content in the river bank sediments and suspended matter is lowest, suggests U release from the solid phase during river transport. About 485 t of U are transported annually to the Amazon delta area in dissolved form, and 1943 t bound to suspended particulate matter. Total U and Th concentrations in the river bank sediments ranged from 1·59 to 7·14 µg g^?1 and from 6·74 to 32 µg g^?1, respectively. The highest concentrations were observed in the Trombetas River. The proportion extracted by means of the hydroxylamine solution (HL) was relatively high for U in the Trombetas river bank sediment (31%) and for Th in the Solimões sediment (30%). According to the alpha recoil effects, the ²³⁴U/²³⁸U activity ratios of the Andean river waters and downstream Amazon water (Óbidos) were >1, but were <1 in the Negro River (at Manaus). The activity ratios of dissolved U correlate with pH and also with the U activity ratios in the river bank sediment hydroxylamine extracts. As expected, the ²³⁴U/²³⁸U activity ratios in river bank sediments were <1 in the Andean rivers and in the downstream Amazon, but they were >1 in the Trombetas and Negro rivers. Such ratios probably result from the binding of dissolved uranium to solid sediment. The ²²⁸Th/²³²Th ratios of river bank sediments were close to unity (except for the Negro River, where it is lower), suggesting no significant Th exchanges between the river water and the sediment. The ²²⁶Ra/²³²Th activity ratios were <1, and the ²²⁶Ra/²²⁸Ra activity ratios generally were significantly higher than the activity ratios of their respective parents. This perhaps is the result of easier leaching of the ²²⁶Ra parent, ²³⁰Th, from solid material (owing to the alpha recoil effect) than of the ²²⁸Ra parent. Uranium and thorium isotopes were used as tools to evaluate the chemical weathering rate of rocks in the Amazon system, which was estimated to be 2·7 cm 1000 year^?1 s^?1. Copyright © 2002 John Wiley & Sons, Ltd.     

Geomorphic effects of large debris flows on channel morphology at North Fork Mountain,eastern West Virginia,USA

Extreme rainfall in June 1949 and November 1985 triggered numerous large debris flows on the steep slopes of North Fork Mountain, eastern West Virginia. Detailed mapping at four sites and field observations of several others indicate that the debris flows began in steep hillslope hollows, propagated downslope through the channel system, eroded channel sediment, produced complex distributions of deposits in lower gradient channels, and delivered sediment to floodwaters beyond the debris-flow termini. Based on the distribution of deposits and eroded surfaces, up to four zones were identified with each debris flow: an upper failure zone, a middle transport/erosion zone, a lower deposition zone, and a sediment-laden floodwater zone immediately downstream from the debris-flow terminus. Geomorphic effects of the debris flows in these zones are spatially variable. The initiation of debris flows in the failure zones and passage through the transport/erosion zones are characterized by degradation; 2300 to 17 000 m³ of sediment was eroded from these zones. The total volume of channel erosion in the transport/erosion zones was 1·3 to 1·5 times greater than the total volume of sediment that initially failed, indicating that the debris flows were effective erosion agents as they travelled through the transport/erosion zones. The overall response in the deposition zones was aggradation. However, up to 43 per cent of the sediment delivered to these zones was eroded by floodwaters from joining tributaries immediately after debris-flow deposition. This sediment was incorporated into floodwaters downstream from the debris-flow termini causing considerable erosion and deposition in these channels. © 1998 John Wiley & Sons, Ltd.     

Breaching in a wave-dominated barrier spit: The trabucador bar (north-eastern spanish coast)

The Trabucador Bar is a barrier coast linking the main lobe of the Ebro Delta with its southern spit. This coastal stretch, which may be considered as a microtidal transgressive barrier, is the most vulnerable area of the deltaic coast to storm-induced geomorphologic changes. During the second week of October 1990 a severe storm affected the Ebro Delta causing serious erosion, in which the Trabucador Bar was one of the most damaged zones. A breach 800 m long and with a maximum depth of 0·4 m below the mean water level was created. During the breaching process approximately 70 000 m³ of sand were removed from the subaerial barrier in a few hours. Three factors are normally responsible for the loss of sediment, longshore transport gradient, offshore transport and overwash processes, most of the eroded sediment (60 000 m³) was transported towards the inner bay due to overwash processes. The post-storm recovery of the zone was slow and far from complete, as the breach remained a conduit for onshore sediment transport under a regime of breaking and reforming waves. An artificial dune was subsequently constructed to close the breach and thus allow beachface recovery.     

Sediment concentration in interrill flow: interactions between soil surface conditions,vegetation and rainfall

A database composed of 673 natural rainfall events with sediment concentration measurements at the field or plot scale was analysed. Measurements were conducted on similar soil type (loess soils prone to sealing phenomenon) to apprehend the variability and complexity involved in interrill erosion processes attributable to soil surface conditions. The effects of the dominant controlling factors are not described by means of equations; rather, we established a classification of potential sediment concentration domain according to combination of the dominant parameters. Thereby, significant differences and evolution trends of mean sediment concentration between the different parameter categories are identified. Further, when parameter influences interact, it allows us to discern the relative effects of factors according to their respective degree of expression. It was shown that crop cover had a major influence on mean sediment concentration, particularly when soil surface roughness is low and when maximum 6‐min intensity of rainfall events exceeds 10 mm h^?1: mean sediment concentration decreases from 8·93 g l^?1 for 0–20 per cent of coverage to 0·97 g l^?1 for 21–60 per cent of coverage. The established classification also indicates that the increase of the maximum 6‐min intensity of the rainfall factor leads to a linear increase of mean sediment concentration for crop cover over 21 per cent (e.g. from 2·96 g l^?1 to 14·44 g l^?1 for the 1–5 cm roughness class) and to an exponential increase for low crop cover (e.g. from 3·92 g l^?1 to 58·76 g l^?1 for the 1–5 cm roughness class). The implication of this work may bring perspective for erosion prediction modelling and give references for the development of interrill erosion equation. Copyright © 2002 John Wiley & Sons, Ltd.     

Dynamics of bedload transport in Turkey brook,a coarse-grained alluvial channel

Automatic and continuously recording samplers are deployed in a Hertfordshire gravel-bed stream to show that bedload transport is related to stream power. The pattern is similar to that already established for North American channels but, because the record is so detailed, it is possible to identify the cause of the considerable scatter that is normal in such relationships. A major factor is the occurrence of rhythmic pulses in bedload discharge that are not matched by similar fluctuations in hydraulic variables. It is suggested that these pulses reflect downstream differences in the concentration of mobile particles in a slow-moving traction carpet, and that they may be likened to kinematic waves. The record also reveals that the threshold of sediment transport—always presumed hithero to be associated with incipient motion—is related to the cessation of bedload transport in a river flood. Indeed, the mean value of stream power at the finish of bedload transport is only 20 percent of that prevailing at the moment of incipient sediment motion. Because of this, there is an inevitably poor correlation between actual bedload transport rates and those predicted by bedload equations which rely upon a single traction threshold. These new data show that the general inverse relationship between bedload discharge and water-depth : grain-size ratio proposed by Bagnold (1977, 1980) is not universal. Transport efficiency for this gravel-bed stream is typically 0.05 per cent of available stream power, which compares with 1.6 per cent for a river moving both gravel and sand, and 5 per cent for another channel where bedload is composed predominantly of sand-sized particles. It is argued that coarse and fine-grained alluvial channels may need to be considered separately. By allowing for differences in traction threshold at the beginning and end of bedload events, and by averaging bedload discharge flood by flood in order to smooth out the effect of pulses, it is possible to achieve a reasonably good prediction of average bedload transport rate in terms of stream power.