Estimating the longevity of limestone drains in treating acid mine drainage containing high concentrations of iron

Limestone drains are often implemented in the treatment of acid mine drainage (AMD), but when the AMD contains high levels of dissolved Fe their lifetime is dependent on the rate of precipitation of Fe hydroxide on the limestone surface. This study used a small-scale laboratory experiment to define the longevity of a limestone drain by determining the thickness of the Fe coating encapsulating the limestone particles when the system lost its maximum neutralising potential. Synthetic AMD (100 mg/L Fe, pH 4–4.8) was pumped through a column containing limestone particles for 1110 h, when the effluent pH had dropped from a maximum of 6.45–4.9. The decline in neutralisation during the experiment was due to the formation of Fe hydroxide coatings on the limestone grains. These coatings are composed of lepidocrocite/goethite in three distinct layers: an initial thick porous orange layer, overlain by a dense dark brown crust, succeeded by a layer of loosely-bound, porous orange globules. After 744 h, a marked increase in the rate of pH decline occurred, and the system was regarded as having effectively failed. At this time the Fe hydroxide crust effectively encapsulated the limestone grains, forming a diffusion barrier that slowed down limestone dissolution. Between the coating and the limestone substrate was a 60 μm wide void, so that agitation of the limestone sample would readily remove the coating from the limestone surface.     

Elevated stream trace and minor element concentrations in the foreland of receding tropical glaciers

Globally, the ongoing retreat of mountain glaciers will ultimately diminish fresh water supplies. This has already begun in watersheds with greatly reduced glacial coverage. Still unknown are the affects of glacial retreat on downstream water quality, including the threats to human and ecosystem health. In the Cordillera Blanca, retreating glaciers have exposed sulfide-rich rock outcrops, negatively affecting the quality of the glacial meltwater. This study has evaluated glacial melt stream hydrogeochemistry in the sulfide-bearing Rio Quilcay watershed (∼9°27′S, ∼77°22′W) during the 2008 dry season. Surface water samples were collected from the upper 12 km of the watershed during the 2008 dry season. Dissolved (0.4 μm) and unfiltered acidified (pH < 2) Al, Co, Cu, Fe, Ni, Mn, Pb, Zn and dissolved major ions and organic C (DOC) concentrations were quantified and pH and temperature were measured in the field. Twenty of 22 stream samples had pH values below 4, generating significantly (p < 0.01, α = 0.05) greater cation denudation normalized to discharge than other worldwide glacier-fed streams. Additionally, dissolved trace and minor element concentrations were comparable to acid mine drainage. Non-conservative dissolved element behaviors resulted from adsorption/desorption reactions in tributary mixing zones. At low pH values, hydrous Fe oxides acted as the dominant sorption surfaces. The poor water quality observed in Cordillera Blanca headwaters coupled with the likely exposure of additional sulfide-rich outcrops from ongoing glacial retreat may pose water quality challenges.     

Dissolution of calcitic marble and dolomitic rock in high iron concentrated acid mine drainage: application to anoxic limestone drains

Oxidation of sulphide mining waste can generate acid mine drainage (AMD) that has the potential to seriously affect the ecosystems. Acid mine drainage is characterised by a high acidity, high concentrations of sulphates and metals. To reduce the environmental impacts due to AMD, neutralisation using limestone drains is an option proposed in the literature and used around the world. The present study focuses on the influence of the carbonate rock mineralogy and their particle size on the neutralising capacity. The tests were performed in two different anoxic conditions: in batch reactors, and in columns having a hydraulic retention time of 15?h. The results showed that the neutralisation capacity of calcite was more important than for dolomitic rock, and smaller particle size gave higher alkalinity production (fine calcite dissolved faster in contact with AMD). A characterization of metal precipitate in sludge and in limestone coating was performed and demonstrated that gypsum, lepidocrocite and goethite were the predominant secondary minerals to be formed. Finally, this study underlines that anoxic limestone drain cannot be used alone to treat high iron concentrated AMD.     

Sources of dissolved REE in mountainous streams draining granitic rocks, Sierras Pampeanas (Córdoba, Argentina)

Stream waters draining granitic terrains from the highest part (850 to 2200 m a.s.l.) of Sierras Pampeanas (Córdoba, Argentina, ∼32°S, ∼65°W) were sampled in order to define sources and distribution of dissolved rare earth elements (REE), and to describe the geochemical processes that govern their mobility. The contribution of the regional granite to the dissolved REE pool in stream water is limited due to the physical conditions predominating in the area (i.e., steep slopes and semiarid climate). Therefore, precipitation is considered a seasonally significant source controlling REE concentration in stream water. Dissolved REE concentrations are inversely correlated with monthly precipitation and rainfall frequency. During the rainy season (i.e., the austral summer) REE concentrations in stream water are lower than during the dry season (i.e., austral winter). Such low concentrations reflect the balance between the REE input from precipitation and their removal by adsorption. In contrast, during the dry season, the longer residence time of water within fractures and colluvium determines an increased REE concentration in the base flow. Lower pH values also contribute to raise REE concentration through desorption from mineral surfaces.     

Influence of Temporal Variations in River Discharge, pH, Alkalinity and Ca on the Speciation and Concentration of Heavy Metals in Some Mining Polluted Rivers

Dissolved (dialysis in situ) and total concentrations ofCu, Zn, Cd and Al in eight mining polluted rivers in the Røros area, central Norway, were determinedby atomic absorption spectrometry (flame and graphite furnace) and compared to pH, Caconcentration and alkalinity through seasonal variations in river discharge. Totalconcentrations of the metals were highest during early spring flood and during summer andautumn rain episodes. Dissolved concentrations also increased as the spring floodproceeded, but small discharge peaks within this 2 month period as well as a considerableautumn flood episode appeared to lower rather than to raise the dissolved metal concentrations.Consequently the dissolved fractions of Zn, Cd and Al showed a significant negative correlationwith river discharge, and were low at the discharge peaks. Possibly high sediment concentrationsoccurring at high flood conditions more than counteracted desorption induced by pHdecrease, and led to decreased dissolved fractions through adsorption. Cu speciationon the other hand seemed to be more closely linked to pH. Alkalinity and Ca concentration,both assumed to protect aquatic life from metal pollution, were significantly lowerduring episodes with high Cu and Al total concentrations.     

Diel variation of arsenic,molybdenum and antimony in a stream draining natural As geochemical anomaly

The Mokrsko Stream in the central Czech Republic is an oxic and slightly alkaline stream that drains a natural As geochemical anomaly. Although long-term monitoring has characterized the general seasonal trends in trace element concentrations (i.e., As, Mo, Cu, Zn) in this stream, little is known about solubility controls and sorption processes that influence diel cycles in trace element concentrations. Trace elements (including As species, Cu, Mn, Mo, Pb and Sb) and other parameters were monitored over two 24-h periods in unfiltered and filtered (0.1 μm) samples collected in August 2010 and June 2011. Copper and Pb were predominantly (>92% of the mass) associated with the particulate fraction (>0.1 μm). Arsenic, Mo and Sb were predominantly (>88% of the mass) in the “dissolved” (<0.1 μm) form. Particulate-associated elements displayed up to a factor of 13 differences between minimum and maximum concentrations, most likely due to increased streamflow related to rainfall events. Dissolved concentrations of the trace metal cations (Cu, Fe, Mn and Pb) were consistently low and displayed no diel trends. Dissolved As(V), Mo and Sb varied on a diel cycle, with increased concentrations (up to 36%) during the late afternoon and decreased concentrations during the nighttime. Diel trends in trace anionic elements are explained by temperature-dependent sorption, as the diel changes in pH during base flow were very small (0.07 std. units). Very low concentrations of As(III), which have been shown to vary in a diel cycle, were attributed to enhanced hydraulic exchange with As(III)-rich hyporheic water during rainfall events.     

Laboratory and field evaluation of a flushable oxic limestone drain for treatment of net-acidic drainage from a flooded anthracite mine, Pennsylvania, USA

This paper demonstrates the use of dissolution-rate data obtained in the laboratory to indicate the potential quality of effluent from a field-scale oxic limestone drain (OLD) treatment system for neutralization of dilute acidic mine drainage (AMD). Effluent from the Reevesdale Mine South Dip Tunnel, a large source of AMD and base flow to the Wabash Creek and Little Schuylkill River in the Southern Anthracite Coalfield of east-central Pennsylvania, is representative of AMD with low concentrations but high loadings of dissolved Fe, Al and other metals because of a high flow rate. In January 2003, rapid neutralization of the AMD from the Reevesdale Mine was achieved in laboratory tests of its reaction rate with crushed limestone in closed, collapsible containers (Cubitainers). The tests showed that net-alkaline effluent could be achieved with retention times greater than 3 h and that effluent alkalinities and associated dissolution rates were equivalent for Fe(OH)₃-coated and uncoated limestone. On the basis of the laboratory results, a flushable OLD containing 1450 metric tons of high-purity calcitic limestone followed by two 0.7-m deep wetlands were constructed at the Reevesdale Mine. During the first year of operation, monthly data at the inflow, outflow and intermediate points within the treatment system were collected (April 2006–2007). The inflow to the treatment system ranged from 6.8 to 27.4 L/s, with median pH of 4.7, net acidity of 9.1 mg/L CaCO₃, and concentrations of dissolved Al, Fe and Mn of 1.0, 1.9 and 0.89 mg/L, respectively. The corresponding effluent from the OLD had computed void-volume retention times of 4.5–18 h, with median pH of 6.6, net acidity of −93.2 mg/L CaCO₃, and concentrations of dissolved Al, Fe and Mn of <0.1, 0.08 and 0.52 mg/L, respectively. The wetlands below the OLD were effective for retaining metal-rich solids flushed at monthly or more frequent intervals from the OLD, but otherwise had little effect on the effluent quality. During the first year of operation, approximately 43 metric tons of limestone were dissolved and 2 metric tons of Al, Fe and Mn were precipitated within the OLD. However, because of the accumulation of these metals within the OLD and possibly other debris from the mine, the effectiveness of the treatment system declined. Despite the installation of a flush-pipe network at the base of the OLD to remove precipitated solids, the limestone bed clogged near the inflow. Consequently, a large fraction of the AMD bypassed the treatment system. To promote flow through the OLD, the flush pipes were open continuously during the last 4 months of the study; however, this effluent was only partially treated because short-circuiting through the pipes decreased contact between the effluent and limestone. A reconfiguration of the flow path through the limestone bed from horizontal to vertical upward could increase the limestone surface area exposed to the metal-laden influent, increase the cross-sectional area perpendicular to flow, decrease the flow path for solids removal, and, consequently, decrease potential for clogging.     

Characterization of limestone reacted with acid-mine drainage in a pulsed limestone bed treatment system at the Friendship Hill National Historical Site,Pennsylvania, USA

Armoring of limestone is a common cause of failure in limestone-based acid-mine drainage (AMD) treatment systems. Limestone is the least expensive material available for acid neutralization, but is not typically recommended for highly acidic, Fe-rich waters due to armoring with Fe(III) oxyhydroxide coatings. A new AMD treatment technology that uses CO₂ in a pulsed limestone bed reactor minimizes armor formation and enhances limestone reaction with AMD. Limestone was characterized before and after treatment with constant flow and with the new pulsed limestone bed process using AMD from an inactive coal mine in Pennsylvania (pH=2.9, Fe =150 mg/l, acidity =1000 mg/l CaCO₃). In constant flow experiments, limestone is completely armored with reddish-colored ochre within 48 h of contact in a fluidized bed reactor. Effluent pH initially increased from the inflow pH of 2.9 to over 7, but then decreased to <4 during the 48 h of contact. Limestone grains developed a rind of gypsum encapsulated by a 10- to 30-μm thick, Fe-Al hydroxysulfate coating. Armoring slowed the reaction and prevented the limestone from generating any additional alkalinity in the system. With the pulsed flow limestone bed process, armor formation is largely suppressed and most limestone grains completely dissolve resulting in an effluent pH of >6 during operation. Limestone removed from a pulsed bed pilot plant is a mixture of unarmored, rounded and etched limestone grains and partially armored limestone and refractory mineral grains (dolomite, pyrite). The ∼30% of the residual grains in the pulsed flow reactor that are armored have thicker (50- to 100-μm), more aluminous coatings and lack the gypsum rind that develops in the constant flow experiment. Aluminium-rich zones developed in the interior parts of armor rims in both the constant flow and pulsed limestone bed experiments in response to pH changes at the solid/solution interface.     

Colloid formation and metal transport through two mixing zones affected by acid mine drainage near Silverton,Colorado

Stream discharges and concentrations of dissolved and colloidal metals (Al, Ca, Cu, Fe, Mg, Mn, Pb, and Zn), SO₄, and dissolved silica were measured to identify chemical transformations and determine mass transports through two mixing zones in the Animas River that receive the inflows from Cement and Mineral Creeks. The creeks were the dominant sources of Al, Cu, Fe, and Pb, whereas the upstream Animas River supplied about half of the Zn. With the exception of Fe, which was present in dissolved and colloidal forms, the metals were dissolved in the acidic, high-SO₄ waters of Cement Creek (pH 3.8). Mixing of Cement Creek with the Animas River increased pH to near-neutral values and transformed Al and some additional Fe into colloids which also contained Cu and Pb. Aluminium and Fe colloids had already formed in the mildly acidic conditions in Mineral Creek (pH 6.6) upstream of the confluence with the Animas River. Colloidal Fe continued to form downstream of both mixing zones. The Fe- and Al-rich colloids were important for transport of Cu, Pb, and Zn, which appeared to have sorbed to them. Partitioning of Zn between dissolved and colloidal phases was dependent on pH and colloid concentration. Mass balances showed conservative transports for Ca, Mg, Mn, SO₄, and dissolved silica through the two mixing zones and small losses (<10%) of colloidal Al, Fe and Zn from the water column.     

Hydrological and geochemical control of metals and arsenic in a Mediterranean river contaminated by acid mine drainage (the Amous River,France); preliminary assessment of impacts on fish (Leuciscus cephalus)

Dissolved and particulate concentrations of metals (Fe, Al, Mn, Co, Ni, Cu, Zn, Cd, Tl, Pb) and As were monitored over a 5 year period in the Amous River downstream of its confluence with a creek severely affected by acid mine drainage (AMD) originating from a former Pb–Zn mine. Water pH ranged from 6.5 to 8.8. Metals were predominantly in dissolved form, except Fe and Pb, which were in particulate form. In the particulate phase, metals were generally associated with Al oxides, whereas As was linked to Fe oxides. Metal concentrations in the dissolved and/or particulate phase were generally higher during the wet season due to higher generation of AMD. Average dissolved (size < 0.22 μm) metal concentrations (μg/L) were 1 ± 4 (Fe), 69 ± 49 (Al), 140 ± 118 (Mn), 4 ± 3 Co, 6 ± 4 (Ni), 1.3 ± 0.8 (Cu), 126 ± 81 (Zn), 1.1 ± 0.7 (Cd), 0.9 ± 0.5 (Tl), 2 ± 3 (Pb). Dissolved As concentrations ranged from 5 to 134 μg/L (30 ± 23 μg/L). During the survey, the concentration of colloidal metals (5 kDa < size < 0.22 μm) was less than 25% of dissolved concentrations. Dissolved metal concentrations were generally higher than the maximum concentrations allowed in European surface waters for priority substances (Ni, Cd and Pb) and higher than the environmental quality standards for other compounds. Using Diffusion Gradient in Thin Film (DGT) probes, metals were shown to be in potentially bioavailable form. The concentrations in Leuciscus cephalus were below the maximum Pb and Cd concentrations allowed in fish muscle for human consumption by the European Water Directive. Amongst the elements studied, only As, Pb and Tl were shown to bioaccumulate in liver tissue (As, Pb) or otoliths (Tl). Bioaccumulation of metals or As was not detected in muscle.     

An empirical method for estimating instream pre-mining pH and dissolved Cu concentration in catchments with acidic drainage and ferricrete

Methods for assessing natural background water quality of streams affected by historical mining are vigorously debated. An empirical method is proposed in which stream-specific estimation equations are generated from relationships between either pH or dissolved Cu concentration in stream water and the Fe/Cu concentration ratio in Fe-precipitates presently forming in the stream. The equations and Fe/Cu ratios for pre-mining deposits of alluvial ferricrete then were used to reconstruct estimated pre-mining longitudinal profiles for pH and dissolved Cu in three acidic streams in Montana, USA. Primary assumptions underlying the proposed method are that alluvial ferricretes and modern Fe-precipitates share a common origin, that the Cu content of Fe-precipitates remains constant during and after conversion to ferricrete, and that geochemical factors other than pH and dissolved Cu concentration play a lesser role in determining Fe/Cu ratios in Fe-precipitates. The method was evaluated by applying it in a fourth, naturally acidic stream unaffected by mining, where estimated pre-mining pH and Cu concentrations were similar to present-day values, and by demonstrating that inflows, particularly from unmined areas, had consistent effects on both the pre-mining and measured profiles of pH and Cu concentration. Using this method, it was estimated that mining has affected about 480 m of Daisy Creek, 1.8 km of Fisher Creek, and at least 1 km of Swift Gulch. Mean values of pH decreased by about 0.6 pH units to about 3.2 in Daisy Creek and by 1–1.5 pH units to about 3.5 in Fisher Creek. In Swift Gulch, mining appears to have decreased pH from about 5.5 to as low as 3.6. Dissolved Cu concentrations increased due to mining almost 40% in Daisy Creek to a mean of 11.7 mg/L and as much as 230% in Fisher Creek to 0.690 mg/L. Uncertainty in the fate of Cu during the conversion of Fe-precipitates to ferricrete translates to potential errors in pre-mining estimates of as much as 0.25 units for pH and 22% for dissolved Cu concentration. The method warrants further testing in other mined and unmined watersheds. Comparison of pre-mining water-quality estimates derived from the ferricrete and other methods in single watersheds would be particularly valuable. The method has potential for use in monitoring remedial efforts at mine sites with ferricrete deposits. A reasonable remediation objective might be realized when the downstream pattern of Fe/Cu ratios in modern streambed Fe-precipitates corresponds to the pattern in pre-mining alluvial ferricrete deposits along a stream valley.     

Water management for acid mine drainage control at the polymetallic Zn–Pb–(Ag–Bi–Cu) deposit Cerro de Pasco, Peru

The geochemical and mineralogical study of the Quiulacocha tailings impoundment has shown that the hydrological connection of the three studied mine-waste systems at Cerro de Pasco (Pyrite-rich waste-rock dump Excelsior, old tailings impoundment Quiulacocha, and the active tailings impoundment Ocroyoc) is a critical concern for effective acid mine drainage (AMD) control and mine-waste management. The Quiulacocha tailings covered 114 ha, comprising 79 Mt of tailings, which contained  50 wt.% pyrite, and are located at 4340 m altitude in a tropical puna climate with about 1025 mm/a rainfall and 988 mm/a of evaporation. The tailings were partially overlain by the Excelsior waste-rock dump, which contains about 26,400,000 m³ of waste rocks that cover 94 ha and contained  60 wt.% of pyrite, which origin from a massive pyrite-quartz replacement body. Therefore, these two mine-waste deposits had a direct hydrological connection, resulting in the export of AMD produced at Excelsior towards Quiulacocha. In the Quiulacocha impoundment there are two different types of tailings recognized, that interact with the AMD from Excelsior: 1) Zn–Pb-rich tailings and 2) Cu–As-rich tailings. During the sampling, the Zn–Pb-rich part of Quiulacocha was not producing important excesses of AMD from the oxidation zone, since the pH increased to near neutral values at 1 m depth. The underlying tailings were still able to neutralize the acidity produced in the oxidation zone through sulfide oxidation by the carbonates (mainly dolomite and siderite) contained in the Zn–Pb mineral assemblage. The main source of AMD in this mine-waste system is the Excelsior waste-rock dump. Its acid seepage infiltrates into Quiulacocha forming a Fe–Zn–Pb plume with a pH 5.5–6.1 and containing up to 7440 mg/L Fe, 627 mg/L Zn, and 1.22 mg/L Pb. The plume was detected at 10–13 m depth in the stratigraphy of Quiulacocha tailings. Additionally, the AMD seepage outcropping at the base of the Excelsior waste-rock dump was channeled on the tailings surface into the Quiulacocha pond (pH 2.3), which covered the Cu–As-rich tailings. Infiltration of this Fe(III)-rich AMD increased tailings oxidation in the southwestern part of the impoundment, and subsequently liberated arsenic by enargite oxidation. Additionally, the AMD collected in the Quiulacocha pond was pumped into the active Ocroyoc tailings impoundment, where sulfide oxidation was strongly enhanced by the input of dissolved Fe(III). Therefore, the AMD management and a hydrological separation of the different mine-waste systems could be a first step to prevent further extension of the AMD problem in order to prevent increased sulfide oxidation by Fe(III)-rich solutions.     

Interaction of acid mine drainage with waters and sediments at the Corona stream, Lousal mine (Iberian Pyrite Belt, Southern Portugal)

This study investigates the geochemical characteristics of the acid mine drainage discharged from the abandoned mine adits and tailing piles in the vicinity of the Lousal mine and evaluates the extent of pollution on water and on the stream sediments of the Corona stream. Atmospheric precipitation interacting with sulphide minerals in exposed tailings produces runoff water with pH values as low as 1.9–2.9 and high concentrations of (9,249–20,700 mg l⁻¹), Fe (959–4,830 mg l⁻¹) and Al (136–624 mg l⁻¹). The acidic effluents and mixed stream water carry elevated Cu, Pb, Zn, Cd and As concentrations that exceed the water quality standards. However, the severity of contamination generally decreases 4 km downstream of the source due to mixing with fresh waters, which causes the dilution of dissolved toxic metals and neutralization of acidity. Some natural attenuation of the contaminants also occurs due to the general reduced solubility of most trace metals, which may be removed from solution, by either co-precipitation or adsorption to the iron and aluminium precipitates.     

Oxygen and sulfur isotope systematics of sulfate produced by bacterial and abiotic oxidation of pyrite

To better understand reaction pathways of pyrite oxidation and biogeochemical controls on δ¹⁸O and δ³⁴S values of the generated sulfate in acid mine drainage (AMD) and other natural environments, we conducted a series of pyrite oxidation experiments in the laboratory. Our biological and abiotic experiments were conducted under aerobic conditions by using O₂ as an oxidizing agent and under anaerobic conditions by using dissolved Fe(III)_aq as an oxidant with varying δ¹⁸O_H2O values in the presence and absence of Acidithiobacillus ferrooxidans. In addition, aerobic biological experiments were designed as short- and long-term experiments where the final pH was controlled at ∼2.7 and 2.2, respectively. Due to the slower kinetics of abiotic sulfide oxidation, the aerobic abiotic experiments were only conducted as long term with a final pH of ∼2.7. The δ³⁴S_SO4 values from both the biological and abiotic anaerobic experiments indicated a small but significant sulfur isotope fractionation (∼−0.7‰) in contrast to no significant fractionation observed from any of the aerobic experiments. Relative percentages of the incorporation of water-derived oxygen and dissolved oxygen (O₂) to sulfate were estimated, in addition to the oxygen isotope fractionation between sulfate and water, and dissolved oxygen. As expected, during the biological and abiotic anaerobic experiments all of the sulfate oxygen was derived from water. The percentage incorporation of water-derived oxygen into sulfate during the oxidation experiments by O₂ varied with longer incubation and lower pH, but not due to the presence or absence of bacteria. These percentages were estimated as 85%, 92% and 87% from the short-term biological, long-term biological and abiotic control experiments, respectively. An oxygen isotope fractionation effect between sulfate and water (ε¹⁸O_SO4-H2O) of ∼3.5‰ was determined for the anaerobic (biological and abiotic) experiments. This measured value was then used to estimate the oxygen isotope fractionation effects between sulfate and dissolved oxygen in the aerobic experiments which were −10.0‰, −10.8‰, and −9.8‰ for the short-term biological, long-term biological and abiotic control experiments, respectively. Based on the similarity between δ¹⁸O_SO4 values in the biological and abiotic experiments, it is suggested that δ¹⁸O_SO4 values cannot be used to distinguish biological and abiotic mechanisms of pyrite oxidation. The results presented here suggest that Fe(III)_aq is the primary oxidant for pyrite at pH < 3, even in the presence of dissolved oxygen, and that the main oxygen source of sulfate is water-oxygen under both aerobic and anaerobic conditions.     

Seasonality of diel cycles of dissolved trace-metal concentrations in a Rocky Mountain stream

Substantial diel (24-h) cycles in dissolved (0.1-m filtration) metal concentrations were observed during summer low flow, winter low flow, and snowmelt runoff in Prickly Pear Creek, Montana. During seven diel sampling episodes lasting 34–61.5 h, dissolved Mn and Zn concentrations increased from afternoon minimum values to maximum values shortly after sunrise. Dissolved As concentrations exhibited the inverse timing. The magnitude of diel concentration increases varied in the range 17–152% for Mn and 70–500% for Zn. Diel increases of As concentrations (17–55%) were less variable. The timing of minimum and maximum values of diel streamflow cycles was inconsistent among sampling episodes and had little relation to the timing of metal concentration cycles, suggesting that geochemical rather than hydrological processes are the primary control of diel metal cycles. Diel cycles of dissolved metal concentrations should be assumed to occur at any time of year in any stream with dissolved metals and neutral to alkaline pH.Electronic Supplementary Material Supplementary material is available for this article if you access the article at . A link in the frame on the left on that page takes you directly to the supplementary material.     

Diel behavior of iron and other heavy metals in a mountain stream with acidic to neutral pH: Fisher Creek, Montana, USA

Three simultaneous 24-h samplings at three sites over a downstream pH gradient were conducted to examine diel fluctuations in heavy metal concentrations in Fisher Creek, a small mountain stream draining abandoned mine lands in Montana. Average pH values at the upstream (F1), middle (F2), and downstream (F3) monitoring stations were 3.31, 5.46, and 6.80, respectively. The downstream increase in pH resulted in precipitation of hydrous ferric oxide (HFO) and hydrous aluminum oxide (HAO) on the streambed. At F1 and F2, Fe showed strong diel cycles in dissolved concentration and Fe(II)/Fe(III) ratio; these cycles were attributed to daytime photoreduction of Fe(III) to Fe(II), reoxidation of Fe(II) to Fe(III), and temperature-dependent hydrolysis and precipitation of HFO. At the near-neutral downstream station, no evidence of Fe(III) photoreduction was observed, and suspended particles of HFO dominated the total Fe load. HFO precipitation rates between F2 and F3 were highest in the afternoon, due in part to reoxidation of a midday pulse of Fe²⁺ formed by photoreduction in the upper, acidic portions of the stream. Dissolved concentrations of Fe(II) and Cu decreased tenfold and 2.4-fold, respectively, during the day at F3. These changes were attributed to sorption onto fresh HFO surfaces. Results of surface complexation modeling showed good agreement between observed and predicted Cu concentrations at F3, but only when adsorption enthalpies were added to the thermodynamic database to take into account diel temperature variations. The field and modeling results illustrate that the degree to which trace metals adsorb onto actively forming HFO is strongly temperature dependent. This study is an example of how diel Fe cycles caused by redox and hydrolysis reactions can induce a diel cycle in a trace metal of toxicological importance in downstream waters.     

Molecular characterization of uranium(VI) sorption complexes on iron(III)-rich acid mine water colloids

A mixing of metal-loaded acid mine drainage with shallow groundwater or surface waters usually initiates oxidation and/or hydrolysis of dissolved metals such as iron (Fe) and aluminum (Al). Colloidal particles may appear and agglomerate with increasing pH. Likewise chemical conditions may occur while flooding abandoned uranium mines. Here, the risk assessment of hazards requires reliable knowledge on the mobility of uranium (U). A flooding process was simulated at mesocosm scale by mixing U-contaminated acid mine water with near-neutral groundwater under oxic conditions. The mechanism of U-uptake by fresh precipitates and the molecular structure of U bonding were determined to estimate the mobility of U(VI). Analytical and spectroscopic methods such as Extended X-ray Absorption Fine-Structure (EXAFS) spectroscopy at the Fe K-edge and the U L_III-edge, and Attenuated Total Reflectance Fourier Transform Infrared (ATR-FTIR) spectroscopy were employed. The freshly formed precipitate was identified as colloidal two-line ferrihydrite. It removed U(VI) from solution by sorption processes, while surface precipitation or structural incorporation of U was not observed. EXAFS data suggest a mononuclear inner-sphere, edge-sharing complex of U(VI) with ferrihydrite in the absence of dissolved carbonate. By employing a novel EXAFS analysis method, Monte Carlo Target Transformation Factor Analysis, we could for the first time ascertain a 3-D configuration of this sorption complex without the necessity to invoke formation of a ternary complex. The configuration suggests a slightly tilted position of the adsorbed unit relative to the edge-sharing Fe(O, OH)₆ octahedra. In the presence of dissolved carbonate and at pH ∼8.0, a distal carbonate O-atom at ∼4.3 Å supports formation of ternary U(VI)-carbonato surface complexes. The occurrence of these complexes was also confirmed by ATR-FTIR. However, in slightly acidic conditions (pH 5-6) in equilibrium with atmospheric CO₂, the U(VI) sorption on ferrihydrite was dominated by the binary complex species Fe(O)₂UO₂, whereas ternary U(VI)-carbonato surface complexes were of minor relevance. While sulfate and silicate were also present in the mine water, they had no detectable influence on U(VI) surface complexation. Our experiments demonstrate that U(VI) forms stable inner-sphere sorption complexes even in the presence of carbonate and at slightly alkaline pH, conditions which previously have been assumed to greatly accelerate the mobility of U(VI) in aqueous environments. Depending on the concentrations of U(VI) and carbonate, the type of surface complexes may change from binary uranyl-ferrihydrite to ternary carbonato-uranyl-ferrihydrite complexes. These different binding mechanisms are likely to influence the binding stability and retention of U(VI) at the macroscopic level.