Mineralogical,geochemical, and microbial investigation of a sulfide-rich tailings deposit characterized by neutral drainage

Mineralogical, geochemical and microbial characterization of tailings solids from the Greens Creek Mine, Juneau, Alaska, was performed to evaluate mechanisms controlling aqueous geochemistry of near-neutral pH pore water and drainage. Core samples of the tailings were collected from five boreholes ranging from 7 to 26 m in depth. The majority of the 51 samples (77%) were collected from the vadose zone, which can extend >18 m below the tailings surface. Mineralogical investigation indicates that the occurrence of sulfide minerals follows the general order: pyrite [FeS₂] >> sphalerite [(Zn,Fe)S] > galena [PbS], tetrahedrite [(Fe,Zn,Cu,Ag)₁₂Sb₄S₁₃] > arsenopyrite [FeAsS] and chalcopyrite [CuFeS₂]. Pyrite constitutes <20 to >35 wt.% of the tailings mineral assemblage, whereas dolomite [CaMg(CO₃)₂] and calcite [CaCO₃] are present at ?30 and 3 wt.%, respectively. The solid-phase geochemistry generally reflects the mineral assemblage. The presence of additional trace elements, including Cd, Cr, Co, Mo, Ni, Se and Tl, is attributed to substitution into sulfide phases. Results of acid–base accounting (ABA) underestimated both acid-generating potential (AP) and neutralization potential (NP). Recalculation of AP and NP based on solid-phase geochemistry and quantitative mineralogy yielded more representative results. Neutrophilic S-oxidizing bacteria (nSOB) and SO₄-reducing bacteria (SRB) are present with populations up to 10⁷ and 10⁵ cells g⁻¹, respectively. Acidophilic S-oxidizing bacteria (aSOB) and iron-reducing bacteria (IRB) were generally less abundant. Primary influences on aqueous geochemistry are sulfide oxidation and carbonate dissolution at the tailings surface, gypsum precipitation–dissolution reactions, as well as Fe reduction below the zone of sulfide oxidation. Pore-water pH values generally ranged from 6.5 to 7.5 near the tailings surface, and from approximately 7–8 below the oxidation zone. Elevated concentrations of dissolved SO₄, S₂O₃, Fe, Zn, As, Sb and Tl persisted under these conditions.     

Distribution of arsenic and nickel in uranium mill tailings,Rabbit Lake,Saskatchewan, Canada

The Rabbit Lake U mine in-pit tailings management facility (TMF) is located in northern Saskatchewan, Canada. The tailings body is approximately 425 m long×300 m wide and 91 m thick at its centre. An investigation of the TMF was performed to collect tailings samples from depth to quantify the distribution of As and Ni in the tailings with respect to ore type and assess the distribution of As and Ni with respect to tailings mineralogy. The tailings body consists of alternating layers of ice, frozen tailings and unfrozen tailings which varied in texture from a slurry to a firm silty sand. The tailings solids are predominately composed of quartz (16–36%), calcium sulphate (0.3–54%) and illite (3 and 14%). Arsenic and Ni concentrations in the tailings show similar patterns with depth which were strongly related to historical changes in As and Ni concentrations in the mill feed. Mineralogy of the ore bodies indicated that As and Ni in the mill feed occurred primarily as 1:1 molar ratio arsenides such as niccolite and gersdorffite. Arsenic and Ni concentrations in the tailings were also measured at a near 1:1 molar ratio. Mill process records showed that an average of 71% of the As in the mill feed was solubilized during leaching. SEM analysis suggested that solubilized As is precipitated as Ca²⁺, Fe³⁺ and Ni²⁺ arsenates during the neutralization process. Mill records indicated that 17,000 tonnes of As were discharged to the TMF of which approximately 88% was as arsenates and 12% as primary arsenides.     

Palaeo-hydrogeological control on groundwater As levels in Red River delta,Vietnam

To study the geological control on groundwater As concentrations in Red River delta, depth-specific groundwater sampling and geophysical logging in 11 monitoring wells was conducted along a 45 km transect across the southern and central part of the delta, and the literature on the Red River delta’s Quaternary geological development was reviewed. The water samples (n = 30) were analyzed for As, major ions, Fe²⁺, H₂S, NH₄, CH₄, δ¹⁸O and δD, and the geophysical log suite included natural gamma-ray, formation and fluid electrical conductivity. The SW part of the transect intersects deposits of grey estuarine clays and deltaic sands in a 15–20 km wide and 50–60 m deep Holocene incised valley. The NE part of the transect consists of 60–120 m of Pleistocene yellowish alluvial deposits underneath 10–30 m of estuarine clay overlain by a 10–20 m veneer of Holocene sediments. The distribution of δ¹⁸O-values (range −12.2‰ to −6.3‰) and hydraulic head in the sample wells indicate that the estuarine clay units divide the flow system into an upper Holocene aquifer and a lower Pleistocene aquifer. The groundwater samples were all anoxic, and contained Fe²⁺ (0.03–2.0 mM), Mn (0.7–320 μM), SO₄ (<2.1 μM–0.75 mM), H₂S (<0.1–7.0 μM), NH₄ (0.03–4.4 mM), and CH₄ (0.08–14.5 mM). Generally, higher concentrations of NH₄ and CH₄ and low concentrations of SO₄ were found in the SW part of the transect, dominated by Holocene deposits, while the opposite was the case for the NE part of the transect. The distribution of the groundwater As concentration (<0.013–11.7 μM; median 0.12 μM (9 μg/L)) is related to the distribution of NH₄, CH₄ and SO₄. Low concentrations of As (?0.32 μM) were found in the Pleistocene aquifer, while the highest As concentrations were found in the Holocene aquifer. PHREEQC-2 speciation calculations indicated that Fe²⁺ and H₂S concentrations are controlled by equilibrium for disordered mackinawite and precipitation of siderite. An elevated groundwater salinity (Cl range 0.19–65.1 mM) was observed in both aquifers, and dominated in the deep aquifer. A negative correlation between aqueous As and an estimate of reduced SO₄ was observed, indicating that Fe sulphide precipitation poses a secondary control on the groundwater As concentration.     

The effect of Ca–Fe–As coatings on microbial leaching of metals in arsenic bearing mine waste

Globally arsenic (As) is a ubiquitous trace element derived from the natural weathering of As-bearing rock. With the onset of reducing conditions, the prevalence of aqueous As(III) may be intensified through biotic and abiotic processes. Here we evaluate the stability of arsenic bearing Ca–Fe hydroxide phases collected from exposed tailings at Ketza River mine, Yukon, Canada, during the reductive dissolution of both acid treated and untreated samples by Shewanella putrefaciens 200R and Shewanella sp. ANA-3. Samples were acid treated in order to remove Ca–Fe oxide coatings and evaluate the influence of these coatings on the rates of microbial Fe(III) and As(V) reduction. Environmental scanning electron microscope (ESEM) micrographs of the solid phase show significant differences in the chemistry and physical morphology of the material by the bacteria over time and are especially evident in the acid treated samples. Moreover, while solution chemistry showed similar As(III) respiration rates of the inoculated acid treated samples for both ANA3 and 200R at ~ 1.1 × 10⁻⁶ μM·s^− 1·m^− 2, the Fe(II) respiration rates differed at 1.4 × 10^− 7 and 9.5 × 10^− 8 μM·s^− 1·m⁻² respectively, thus suggesting strain specific metal reduction metabolic pathways Additionally, the enhanced metal reduction observed in the acid treated inoculated samples suggests that the presence of the Ca–Fe hydroxide phase in the untreated samples acted as a barrier, inhibiting the bacteria from accessing the metals. This has implications for increased mobilization of metals by metal reducing bacteria within areas of increased acidity, such as acid mine drainage sites and industrial tailings ponds that can come into contact with surface and ground water sources.     

Arsenic remobilization from sediments contaminated with mine tailings near the Adak mine in Västerbotten district (northern Sweden)

Weathering of mine tailings have resulted in high As concentrations in water (up to 2900 μg l^− 1) and sediment (up to 900 mg kg^− 1) samples around the Adak mine. Notably, As occurs as As(III) species (15–85%) in the oxic surface and ground water samples, which is not common. Time-series based sediment incubations were set up in the laboratory with contaminated sediments to study the microbial processes involved in transformation and remobilization of As across the sediment–water interface. The microcosm experiments indicate that microorganisms are capable of surviving in As-rich sediments and reduce As(V) to As(III). A decrease in total As concentration in sediments is coupled to an increase in As(III) concentration in the aqueous media. In contrast, the controls (treated with HgCl₂ and formaldehyde) did not show growth, and As(V) concentrations increased steadily in the sediments and aqueous medium. The results imply that active metabolism is necessary for As(V) reduction. These microorganisms possess reduction mechanisms that are not necessarily coupled to respiration, but most likely impart resistance to As toxicity.     

Sorption of lead by phlogopite-rich mine tailings

The Pb sorption capacity of apatite ore mine tailings and its potential to act as a remediation agent in a Pb polluted areas were investigated. The tailings, originating from the Siilinjärvi carbonatite complex in Finland, consist mainly of phlogopite and calcite accompanied by apatite residues. The ability of the tailings to retain Pb from an aqueous solution was investigated using an isotherm technique. Furthermore, in a 3-month incubation experiment, uncontaminated mineral soil was amended with untreated tailings and with tailings artificially weathered with acid to increase the quantity of Al and Fe (hydr)oxides. Tailings of two particle-sizes (∅ > 0.2 mm and ∅ < 0.2 mm) somewhat differing in their mineralogical composition were investigated as separate amendments. All tailings materials were added to the soil in two dosages (5 g and 10 g of tailings per 125 g of soil). Following incubation, tailings-induced changes in the Pb sorption capacity of the soil were investigated with the isotherm technique. Finally, to investigate the distribution of sorbed Pb among various chemical pools, the soil samples amended with tailings were contaminated with Pb and then subjected to sequential fractionation analysis. The results revealed efficient removal of Pb from an aqueous solution by the tailings, presumably through precipitation and surface complexation mechanisms. Amending the soil with the tailings increased the mass-based maximum Pb sorption capacity from 10.8 mg kg⁻¹ of the control soil to 14–20.5 mg kg⁻¹ for the untreated tailings and to 32.1–72.1 mg kg⁻¹ for the acid-treated material. The tailings transferred Pb from the exchangeable pool to the non-extracted one and thereby substantially decreased its bioavailability. The material with a particle diameter of less than 0.2 mm had a higher mass-based Pb sorption capacity than the large-sized material. The results suggest that the tailings may potentially serve as an immobilizing agent in polluted areas.     

An evaluation of copper remobilization from mine tailings in sulfidic environments

A laboratory-based assessment of copper remobilization from Cu-rich mine tailings exposed to anoxic, sulfide rich waters was performed. The results from incubation experiments, conducted over a 20 day period, were compared to thermodynamic modelling calculations of copper speciation in sulfidic waters. The tailings materials were observed to react rapidly with added sulfide, consuming 159 μmol HS⁻ g⁻¹ (dry wt) within a 24 h period. The consumption of sulfide was attributed to a two stage process involving the reduction of Fe-hydroxy phases by sulfide followed by reaction with available Fe²⁺ and Cu²⁺ resulting in the formation Fe- and Cu-sulfide phases. During incubation experiments, the dissolved copper concentrations in the absence of sulfide were approximately 0.31 μmol l⁻¹, whereas in the presence of sulfide (0.5–5 mM) concentrations were typically 0.24 μmol l⁻¹. The experiments did not indicate enhanced solubility owing to the formation of soluble copper sulfide species. The predictions (based on the most recent thermodynamic data for aqueous Cu-sulfide and Cu-polysulfide species) did not accurately explain the laboratory observations. Model predictions were greatly influenced by the assumptions made about the oxidation state of copper under anoxic conditions and the solid sulfide phase controlling copper solubility. The study emphasizes the limitations of modelling copper speciation in sulfidic waters and the need for laboratory or field verification of predictions.     

Arsenic associations in sediments from the loess aquifer of La Pampa,Argentina

Groundwater from the Quaternary loess aquifer of La Pampa, central Argentina, has significant problems with high concentrations of As (up to 5300 μg L⁻¹) as well as other potentially toxic trace elements such as F, B, Mo, U, Se and V. Total As concentrations in 45 loess samples collected from the aquifer have a range of 3–18 mg kg⁻¹ with a mean of 8 mg kg⁻¹. These values are comparable to world-average sediment As concentrations. Five samples of rhyolitic ash from the area have As concentrations of 7–12 mg kg⁻¹. Chemical analysis included loess sediments and extracted porewaters from two specially cored boreholes. Results reveal a large range of porewater As concentrations, being generally higher in the horizons with highest sediment As concentrations. The displaced porewaters have As concentrations ranging up to 7500 μg L⁻¹ as well as exceptionally high concentrations of some other oxyanion species, including V up to 12 mg L⁻¹. The highest concentrations are found in a borehole located in a topographic depression, which is a zone of likely groundwater discharge and enhanced residence time. Comparison of sediment and porewater data does not reveal unequivocally the sources of the As, but selective extract data (acid-ammonium oxalate and hydroxylamine hydrochloride) suggest that much of the As (and V) is associated with Fe oxides. Primary oxides such as magnetite and ilmenite may be partial sources but given the weathered nature of many of the sediments, secondary oxide minerals are probably more important. Extract compositions also suggest that Mn oxide may be an As source. The groundwaters of the region are oxidising, with dissolved O₂, NO₃ and SO₄ normally present and As(V) usually the dominant dissolved As species. Under such conditions, the solubility of Fe and Mn oxides is low and As mobilisation is strongly controlled by sorption–desorption reactions. Desorption may be facilitated by the relatively high-pH conditions of the groundwaters in the region (7.0–8.8) and high concentrations of potential competitors (e.g. V, P, HCO₃). PHREEQC modelling suggests that the presence of V at the concentrations observed in the Pampean porewaters can suppress the sorption of As to hydrous Fe(III) oxide (HFO) by up to an order of magnitude. Bicarbonate had a comparatively small competitive effect. Oxalate extract concentrations have been used to provide an upper estimate of the amount of labile As in the sediments. A near-linear correlation between oxalate-extractable and porewater As in one of the cored boreholes investigated has been used to estimate an approximate K_d value for the sediments of 0.94 L kg⁻¹. This low value indicates that the sediments have an unusually low affinity for As.     

Dissolved metals and associated constituents in abandoned coal-mine discharges,Pennsylvania, USA. Part 1: Constituent quantities and correlations

Complete hydrochemical data are rarely reported for coal-mine discharges (CMD). This report summarizes major and trace-element concentrations and loadings for CMD at 140 abandoned mines in the Anthracite and Bituminous Coalfields of Pennsylvania. Clean-sampling and low-level analytical methods were used in 1999 to collect data that could be useful to determine potential environmental effects, remediation strategies, and quantities of valuable constituents. A subset of 10 sites was resampled in 2003 to analyze both the CMD and associated ochreous precipitates; the hydrochemical data were similar in 2003 and 1999. In 1999, the flow at the 140 CMD sites ranged from 0.028 to 2210 L s⁻¹, with a median of 18.4 L s⁻¹. The pH ranged from 2.7 to 7.3; concentrations (range in mg/L) of dissolved (0.45-μm pore-size filter) SO₄ (34–2000), Fe (0.046–512), Mn (0.019–74), and Al (0.007–108) varied widely. Predominant metalloid elements were Si (2.7–31.3 mg L⁻¹), B (<1–260 μg L⁻¹), Ge (<0.01–0.57 μg L⁻¹), and As (<0.03–64 μg L⁻¹). The most abundant trace metals, in order of median concentrations (range in μg/L), were Zn (0.6–10,000), Ni (2.6–3200), Co (0.27–3100), Ti (0.65–28), Cu (0.4–190), Cr (<0.5–72), Pb (<0.05–11) and Cd (<0.01–16). Gold was detected at concentrations greater than 0.0005 μg L⁻¹ in 97% of the samples, with a maximum of 0.0175 μg L⁻¹. No samples had detectable concentrations of Hg, Os or Pt, and less than half of the samples had detectable Pd, Ag, Ru, Ta, Nb, Re or Sn. Predominant rare-earth elements, in order of median concentrations (range in μg/L), were Y (0.11–530), Ce (0.01–370), Sc (1.0–36), Nd (0.006–260), La (0.005–140), Gd (0.005–110), Dy (0.002–99) and Sm (<0.005–79). Although dissolved Fe was not correlated with pH, concentrations of Al, Mn, most trace metals, and rare earths were negatively correlated with pH, consistent with solubility or sorption controls. In contrast, As was positively correlated with pH.     

Precipitation of aluminum and magnesium secondary minerals from uranium mill raffinate (pH 1.0–10.5) and their controls on aqueous contaminants

Models of geochemical controls on elements of concern (EOCs; e.g., As, Se, Mo, Ni) in U tailings are dominated by ferrihydrite. However, the evolution of aqueous concentrations of Al and Mg through the Key Lake (KL) U mill bulk neutralization process indicates that secondary Al and Mg minerals comprise a large portion of the tailings solids. X-ray diffraction, Al K-edge XAS, and TEM elemental mapping of solid samples collected from a pilot-scale continuous-flow synthetic raffinate neutralization system of the KL mill indicate the secondary Al–Mg minerals present include Mg–Al hydrotalcite, amorphous Al(OH)₃, and an amorphous hydrobasaluminite-type phase. The ferrihydrite present contains Al and may be more accurately described as Al–Fe(OH)₃. In the final combined tailings sample (pH 10.5) collected from the model experiments using raffinate with Al, Mg, and Fe, solid phase EOCs were associated with Al–Fe(OH)₃ and Mg–Al hydrotalcite. In model experiments using raffinate devoid of Fe, aqueous EOC concentrations decreased greatly at pH 4.0 (i.e., where ferrihydrite would precipitate) and largely remained in the solid phase when increased to the terminal pH of 10.5; this suggests Al–Mg minerals can control aqueous concentrations of EOCs in the raffinate in the absence of Fe. Maximum adsorption capacities for individual and mixtures of adsorbates by Mg–Al hydrotalcite were determined. A revised model of the geochemical controls in U mill tailings is presented in which Al and Mg minerals co-exist with Fe minerals to control EOC concentrations.     

Predicting arsenic concentrations in the porewaters of buried uranium mill tailings

The proposed JEB Tailings Management Facility (TMF) to be emplaced below the groundwater table in northern Saskatchewan, Canada, will contain uranium mill tailings from McClean Lake, Midwest and Cigar Lake ore bodies, which are high in arsenic (up to 10%) and nickel (up to 5%). A serious concern is the possibility that high arsenic and nickel concentrations may be released from the buried tailings, contaminating adjacent groundwaters and a nearby lake. Laboratory tests and geochemical modeling were performed to examine ways to reduce the arsenic and nickel concentrations in TMF porewaters so as to minimize such contamination from tailings buried for 50 years and longer. The tests were designed to mimic conditions in the mill neutralization circuit (3 hr tests at 25°C), and in the TMF after burial (5–49 day aging tests). The aging tests were run at, 50, 25 and 4°C (the temperature in the TMF). In order to optimize the removal of arsenic by adsorption and precipitation, ferric sulfate was added to tailings raffinates¹ having Fe/As ratios of less that 3–5. The acid raffinates were then neutralized by addition of slaked lime to nominal pH values of 7, 8, or 9.Analysis and modeling of the test results showed that with slaked lime addition to acid tailings raffinates, relatively amorphous scorodite (ferric arsenate) precipitates near pH 1, and is the dominant form of arsenate in slake limed tailings solids except those high in Ni and As and low in Fe, in which cabrerite-annabergite (Ni, Mg, Fe(II) arsenate) may also precipitate near pH 5–6. In addition to the arsenate precipitates, smaller amounts of arsenate are also adsorbed onto tailings solids.The aging tests showed that after burial of the tailings, arsenic concentrations may increase with time from the breakdown of the arsenate phases (chiefly scorodite). However, the tests indicate that the rate of change decreases and approaches zero after 72 hrs at 25°C, and may equal zero at all times in the TMF at 4°C. Consistent with a kinetic model that describes the rate of breakdown of scorodite to form hydrous ferric oxide, the rate of release of dissolved arsenate to tailings porewaters from slake limed tailings: (1) is proportional to pH above pH 6–7; (2) decreases exponentially as the total molar Fe/As ratio of tailings raffinates is increased from 1/1 to greater than 5/1; and (3) is proportional to temperature with an average Arrhenius activation energy of 13.4 ± 4.2 kcal/mol.Study results suggest that if ferric sulfate and slaked lime are added in the tailings neutralization circuit to give a raffinate Fe/As molar ratio of at least 3–5 and a nominal (initial) pH of 8 (final pH of 7–8), arsenic and nickel concentrations of 2 mg/L or less, are probable in porewaters of individual tailings in the TMF for 50 to 10,000 yrs after tailings disposal. However, the tailings will be mixed in the TMF, which will contain about 35% tailings with Fe/As = 3.0, and 65% tailings with Fe/As = 5.0–7.7. Thus, it seems likely that average arsenic pore water concentrations in the TMF may not exceed 1 mg/L.     

Hydrogeochemistry of arsenic and other inorganic constituents in groundwaters from La Pampa,Argentina

Groundwaters from Quaternary loess aquifers in northern La Pampa Province of central Argentina have significant quality problems due to high concentrations of potentially harmful elements such as As, F, NO₃-N, B, Mo, Se and U and high salinity. The extent of the problems is not well-defined, but is believed to cover large parts of the Argentine Chaco-Pampean Plain, over an area of perhaps 10⁶ km². Groundwaters from La Pampa have a very large range of chemical compositions and spatial variability is considerable over distances of a few km. Dissolved As spans over 4 orders of magnitude (<4–5300 μg l⁻¹) and concentrations of F have a range of 0.03–29 mg l⁻¹, B of 0.5–14 mg l^−l, V of 0.02–5.4 mg l⁻¹, NO₃–N of <0.2–140 mg l⁻¹, Mo of 2.7–990 μg l⁻¹ and U of 6.2–250 μg l⁻¹. Of the groundwaters investigated, 95% exceed 10 μg As l⁻¹ (the WHO guideline value) and 73% exceed 50 μg As l⁻¹ (the Argentine national standard). In addition, 83% exceed the WHO guideline value for F (1.5 mg l⁻¹), 99% for B (0.5 mg l⁻¹), 47% for NO₃-N (11.3 mg l⁻¹), 39% for Mo (70 μg l⁻¹), 32% for Se (10 μg l⁻¹) and 100% for U (2 μg l⁻¹). Total dissolved solids range between 730 and 11400 mg l⁻¹, the high values resulting mainly from evaporation under ambient semi-arid climatic conditions. The groundwaters are universally oxidising with high dissolved-O₂ concentrations. Groundwater pHs are neutral to alkaline (7.0–8.7). Arsenic is present in solution predominantly as As(V). Groundwater As correlates positively with pH, alkalinity (HCO₃), F and V. Weaker correlations are also observed with B, Mo, U and Be. Desorption of these elements from metal oxides, especially Fe and Mn oxides under the high-pH conditions is considered an important control on their mobilisation. Mutual competition between these elements for sorption sites on oxide minerals may also have enhanced their mobility. Weathering of primary silicate minerals and accessory minerals such as apatite in the loess and incorporated volcanic ash may also have contributed a proportion of the dissolved As and other trace elements. Concentrations of As and other anions and oxyanions appear to be particularly high in groundwaters close to low-lying depressions which act as localised groundwater-discharge zones. Concentrations up to 7500 μg l⁻¹ were found in saturated-zone porewaters extracted from a cored borehole adjacent to one such depression. Concentrations are also relatively high where groundwater is abstracted from close to the water table, presumably because this zone is a location of more active weathering reactions. The development of groundwaters with high pH and alkalinity results from silicate and carbonate reactions, facilitated by the arid climatic conditions. These factors, together with the young age of the loess sediments and slow groundwater flow have enabled the accumulation of the high concentrations of As and other elements in solution without significant opportunity for flushing of the aquifer to enable their removal.     

Environmental geochemistry of an active Hg mine in Xunyang,Shaanxi Province,China

The Xunyang Hg mine (XMM) situated in Shaanxi Province is an active Hg mine in China. Gaseous elemental Hg (GEM) concentrations in ambient air were determined to evaluate its distribution pattern as a consequence of the active mining and retorting in the region. Total Hg (HgT) and methylmercury (MeHg) concentrations in riparian soil, sediment and rice grain samples (polished) as well as Hg speciation in surface water samples were measured to show local dispersion of Hg contamination. As expected, elevated concentrations of GEM were found, ranging from 7.4 to 410 ng m⁻³. High concentrations of HgT and MeHg were also obtained in riparian soils, ranged from 5.4 to 120 mg kg⁻¹ and 1.2 to 11 μg kg⁻¹, respectively. Concentrations of HgT and MeHg in sediment samples varied widely from 0.048 to 1600 mg kg⁻¹ and 1.0 to 39 μg kg⁻¹, respectively. Surface water samples showed elevated HgT concentrations, ranging from 6.2 to 23,500 ng L⁻¹, but low MeHg concentrations, ranging from 0.022 to 3.7 ng L⁻¹. Rice samples exhibited high concentrations of 50–200 μg kg⁻¹ in HgT and of 8.2–80 μg kg⁻¹ in MeHg. The spatial distribution patterns of Hg speciation in the local environmental compartments suggest that the XMM is the source of Hg contaminations in the study area.     

Trace elements and ions in Italian bottled mineral waters: Identification of anomalous values and human health related effects

Microbiological studies have always had an important role in the evaluation of drinking water quality. However, since geological processes are the most important factors controlling the source and distribution of chemical elements in natural waters, the importance of geochemical data must not be underestimated. This study presents data on pH, conductivity and concentrations of 69 elements and ions (Ag, Al, As, B, Ba, Be, Bi, Ca, Cd, Ce, Co, Cr, Cs, Cu, Dy, Er, Eu, Fe, Ga, Gd, Ge, Hf, Hg, Ho, I, K, La, Li, Lu, Mg, Mn, Mo, Na, Nb, Nd, Ni, Pb, Pr, Rb, Sb, Sc, Se, Sm, Sn, Sr, Ta, Tb, Te, Th, Ti, Tl, Tm, U, V, W, Y, Yb, Zn, Zr, Br⁻, HCO₃⁻, Cl⁻, F⁻, NH₄⁺, NO₂⁻, NO₃⁻, PO₄³⁻, SO₄²⁻, SiO₂) from 186 bottled mineral waters of 158 different Italian name brands. Analyses show a large range in concentrations for most of these elements, with variations up to four orders of magnitude. Our data demonstrate that some elements (such as Be), generally considered unlikely to occur, can instead reach surprisingly high levels in drinking water, and also how packaging can release some trace elements to the bottled water. Data analysis shows that the implementation of an international database of bottled water geochemistry and of potential toxicological effects is of paramount importance to provide a robust data set which would be useful to set international action levels and guidelines to secure bottled water quality, whose consumption has steadily increased in the recent years. A new formula to calculate nitrate and nitrite tolerable concentration levels in waters intended for human consumption is proposed, to take into account that about 5% of dietary nitrate in humans is converted to nitrite.     

Ni(II) sorption on natural chlorite

Sorption of Ni(II) onto chlorite surfaces was studied as a function of pH (5–10), ionic strength (0.01–0.5 M) and Ni concentration (10⁻⁸–10⁻⁶ M) in an Ar atmosphere using batch sorption with radioactive ⁶³Ni as tracer. Such studies are important since Ni(II) is one of the major activation products in spent nuclear fuel and sorption data on minerals such as chlorite are lacking. The sorption of Ni(II) onto chlorite was dependent on pH but not ionic strength, which indicates that the process primarily comprises sorption by surface complexation. The maximum sorption was at pH ∼ 8 (K_d = ∼10⁻³ cm³/g). Desorption studies over a period of 1–2 weeks involving replacement of the aqueous solution indicated a low degree of desorption. The acid–base properties of the chlorite mineral were determined by titration and described using a non-electrostatic surface complexation model in FITEQL. A 2-pK NEM model and three surface complexes, Chl_OHNi²⁺, Chl_OHNi(OH)⁺ and Chl_OHNi(OH)₂, gave the best fit to the sorption results using FITEQL. The high K_d values and low degree of desorption observed indicate that under expected groundwater conditions, a large fraction of Ni(II) that is potentially leachable from spent nuclear fuel may be prevented from migrating by sorption onto chlorite surfaces.     

Irrigation produces elevated arsenic in the underlying groundwater of a semi-arid basin in Southwestern Idaho

The shallow aquifer beneath the Western Snake River Plain (Idaho, USA) exhibits widespread elevated arsenic concentrations (up to 120 μg L⁻¹). While semi-arid, crop irrigation has increased annual recharge to the aquifer from approximately 1 cm prior to a current rate of >50 cm year⁻¹. The highest aqueous arsenic concentrations are found in proximity to the water table (all values >50 μg L⁻¹ within 50 m) and concentrations decline with depth. Despite strong vertical redox stratification within the aquifer, spatial distribution of aqueous species indicates that redox processes are not primary drivers of arsenic mobilization. Arsenic release and transport occur under oxidizing conditions; groundwater wells containing dissolved arsenic at >50 μg L⁻¹ exhibit elevated concentrations of O₂ (average 4 mg L⁻¹) and NO₃ (average 8 mg L⁻¹) and low concentrations of dissolved Fe (<20 μg L⁻¹). Sequential extractions and spectroscopic analysis of surficial soils and sediments indicate solid phase arsenic is primarily arsenate and is present at elevated concentrations (4–45 mg kg⁻¹, average: 17 mg kg⁻¹) relative to global sedimentary abundances. The highest concentrations of easily mobilized arsenic (up to 7 mg kg⁻¹) are associated with surficial soils and sediments visibly stained with iron oxides. Batch leaching experiments on these materials using irrigation waters produce pore water arsenic concentrations approximating those observed in the shallow aquifer (up to 152 μg L⁻¹). While As:Cl aqueous phase relationships suggest minor evaporative enrichment, this appears to be a relic of the pre-irrigation environment. Collectively, these data indicate that infiltrating irrigation waters leach arsenic from surficial sediments to the underlying aquifer.     

The arsenic source term for an in-pit uranium mine tailings facility and its long-term impact on the regional groundwater

Detailed field sampling and analyses and laboratory-based diffusion-cell experiments were used in conjunction with 3-D reactive transport modeling (MODFLOW and MT3D99) to quantify the fate and long-term (10 ka) transport of As in the Rabbit Lake In-pit Tailings Management Facility (RLITMF), northern Saskatchewan, Canada. The RLITMF (300 m × 425 m × 90 m thick) was engineered to ensure solute transport within the RLITMF is dominated by diffusion. Concentrations of As in the tailings pore fluids ranged from 0.24 to 140 mg/L (n = 43). Arsenic speciation analyses indicate 90% of this arsenic exists as As⁵⁺. This observation is supported by pH–Eh measurements of pore fluids (n = 135). Geochemical analyses yielded a strong inverse correlation between the Fe/As molar ratio in the tailings solids and the corresponding concentration of dissolved As, which is attributed to the adsorption of As to secondary 2-line ferrihydrite present in the tailings. Diffusion-cell testing yielded values for the effective diffusion coefficient, sorption coefficient, and effective porosity of As in the tailings of 4.5 × 10⁻¹⁰ m²/s, 2–4 cm³/g and 0.36, respectively. Reactive transport simulations using the field and laboratory data show adsorption of As to the tailings and diffusive transport of dissolved As in the tailings should reduce the source term concentration of As to between 40% and 70% of the initial concentrations over the 10 ka simulation period. Based on these simulations, the As concentrations in the regional groundwater, 50 m down gradient of the tailings facility, should be maintained at background concentrations of 0.001 mg/L over the 10 ka period. These findings suggest the engineered in-pit disposal of U mine tailings can provide long-term protection for the local groundwater regime from As contamination.     

Spatial distribution and source diagnosis of polycyclic aromatic hydrocarbons in soils from Chengdu Economic Region,Sichuan Province,western China

Surface soils from the Chengdu Economic Region (CER) were analyzed for sixteen United States Environment Protection Agency priority polycyclic aromatic hydrocarbons (PAHs) to study the spatial distribution and to identify the sources of PAHs. Relatively high concentrations (more than 1500 ngg^− 1) of high molecular weight PAHs were found in Chengdu Plain, in the middle of CER, while high concentrations (more than 500 ng g^− 1) of low molecular weight PAHs were detected in the surrounding mountains. The concentrations of ∑₁₆-PAHs in topsoil samples from CER (12.52–75,431.47 ngg^− 1, average value was 3233.92 ngg^− 1) were higher than that from the southern China (21.91–3077 ngg^− 1, average value was less than 500 ngg^− 1), and they were comparable to concentrations in soils from the northern China (366–254,080 ngg^− 1, mean value was more than 3000 ngg^− 1). The concentrations from CER were also much higher than the concentrations of some world clean regions such as Antarctic (34.9–171 ngg^− 1), European high mountains (9–11,000 ngg^− 1, mean value was 158 ngg^− 1) and some Europe residential (736 ngg^− 1) and arable soils (60–145 ngg^− 1, mean value was 66 ngg^− 1). The ratio of tracer compounds (BaA/(BaA + Chr), Flo/(Flo + Pyr), and IcdP/(IcdP + BghiP)) indicated that the high concentrations of PAHs in soils were mainly derived from fossil fuels combustion in mountain region and from the incomplete combustion of petroleum in developed plain area (such as Chengdu and Deyang). From the above distribution characteristics and ratios of tracer compounds, we inferred the reasons for the distribution pattern of PAHs in CER were the domestic heating, emissions, and the physicochemical properties of PAHs.