Increasing of efficiency of desulphurisation processes of coals during thermal destruction

As is well known, a high content of sulphur in coals is an effect of the post-depositional history of coal seams and one of the most important criteria of its use as a fuel. Sulphur in coals can cause a serious environmental and technological problem during their utilization. This problem is very actual for the Donetsk Basin because 734 mined seams out of the total of 1009 （73%） are comprised of coals with sulphur content -2%. The chemical pre-treatment as a first stage in their processing is widely used in order to effectively obtain the thermal destruction products of coals （such as semi-coke, coke, adsorbents, etc.） and to simultaneously utilize coal wastes. Development in pre-treatment methods for high-sulphur, low-rank coals is especially desirable for reducing the sulphur contents of the solid products. The aim of the present work is to investigate the influence of coal pre-treatment on the yield and composition of thermal destruction products, and the sulphur distribution among different components of the coals of different genetic types by reductivity （low-reduced LRC and reduced RC coals）. The thermal behavior of the coals was studied by means of the Fisher method （heated to 520℃, at a rate of 7℃/min）. The composition of the semi-coking gas was investigated by means of a VTI gas analyzer. The coal samples were chemically treated directly before thermal destruction by the introduction of 1-% solutions of radical polymerization initiator AAD （acrylic acid dinitrile C8H12N4） and products of coal-tar distillation （absorber oil）. Coal pre-treatment increases the semi-coke yield and its coking ability, and changes the liquid/gaseous product ratio.     

Quartz Cement in Middle Jurassic Reservoir Sandstones in North Sea A Review. Part II： Duration and Silica Sources

The timing and duration of quartz cementation in sandstones have been mainly inferred from diagenetic texture, relationship between pore filling minerals, fluid inclusions and isotopic data. Fluid inclusion temperatures from North Sea reservoir sandstones indicate that most of the quartz cement forms at temperature exceeding 90℃ and is continually proceeding after oil emplacement, based on the fluid inclusion temperatures in quartz overgrowth which is approaching the bottom-hole temperatures. The duration of quartz cement after oil emplacement depends upon the saturation of porewater and the distribution of pore water film and the property of water-wet or oil-wet of the reactants. The leaching of K-feldspar by meteoric water requires pore water flow to move the released potassium and sodium and silica out the solution, which suggests the mechanism does not appear to be a major source of silica for quartz cementation. The quartz cementation coincidence with the compaction and pressure solution suggests the major source of silica. The alteration of feldspar by illitization of kaolinite may serve as another important source of silica at deep burial depth. External sources are not need to call on for illustrating the quartz cementation, because there is no evidences for large scale convection of pore water flow occurred in the burial history of reservoir sandstones of middle Jurassic in the North Sea.     

A Mineralogical Study of Diatomite in Leizhou Peninsula

In this paper diatomite samples taken from the Leizhou Peninsula have been studied by chemical analysis, DTA, TG, XRD, IR ,SEM and X-ray Energy Spectroscopy.The study shows that the diatomaceous genera and species and their organic contents are variable with buried depth ,from Melosira to Stephanodiscus and then to Cyclotella. Various impurities in the samples, such as quartz, kaolinite and montmorillonite indicate different sedimentary environments. When heated, the diatom would change in shape due to the phase transformation in which amorphous silica crystallized from disordered opal to ordered cristobalite. The temperatures of phase transformation are different for various diatoms due to the presence of different impurities and constituents of diatomaceous genera and species.     

Spatial and temporal variation of heavy metal contamination in sediments of Dexing region, Jiangxi Province, China

Mining is one of the most important contamination sources of heavy metals in sediments. Mining and mineral processing in the Dexing region of China have been carried out for over forty years. The aim of this study was to assess the spatial and temporal va…     

Separation and Precise Measurement of Lithium Isotopes in Three Reference Materials Using Multi Collector‐Inductively Coupled Plasma Mass Spectrometry

Lithium separation technique for three reference materials has been established together with precise determination of lithium isotope using a Neptune multi collector-inductively coupled plasma mass spectrometry (MC-ICP-MS). The solutions of lithium element standard reference materials, potassium, calcium, sodium, magnesium and iron single element, were used to evaluate analytical methods applied. Three separate stages of ion-exchange chromatography were carried out using organic cation-exchange resin (AG 50W-X8). Lithium was enriched for the three stages using different eluants, which are 2.8 M HCl, 0.15 M HCl and 0.5 M HCl in 30% ethanol, respectively. The columns for the first and second stages are made of polypropylene, and those for the third stage are made of quartz. Total reagent volume for the entire chemical process was 35 mL for three reference materials. The recovery yielded for the three stages is 98.9–101.2% with an average of 100.0%, 97.6–101.9% with an average of 99.9%, and 99.8–103.3% with an average of 100.6%, respectively. The precision of this technique is conservatively estimated to be ±0.72–1.04‰ (2σ population), which is similar to the precision obtained by different authors in different laboratories with MC-ICP-MS. The δ7Li values (7Li/6Li relative to the IRMM-016 standard) determined for andesite (AGV-2) and basalt (BHVO-2) are 5.68‰ (n=18), 4.33‰ (n=18), respectively. The δ7Li value (7Li/6Li relative to the L-SVEC standard) determined for IRMM-016 is –0.01‰ (n=15). All these analytical results are in good agreement with those previously reported. In addition, the results for the same kinds of samples analyzed at the MLR Key Laboratory of Metallogeny and Mineral Assessment, Institute of Mineral Resources, Chinese Academy of Geological Sciences, are consistent with those obtained at the Plasma Laboratory, University of Maryland, within analytical uncertainty. According to these experiment results, it is concluded that this proposed procedure is a suitable method for determining the lithium isotopic composition of natural samples.     

Mineralogy, geochemistry and release of heavy metals in wastes from indigenous zinc smelting in Northwest Guizhou

Environmental impact resulting from mining activities is serious and ubiquitous all over the world, and it has become one of the important aspects in environmental geochemistry. The environment was seriously damaged by wastes from historical zinc smelting in Northwest Guizhou. The geochemical distributions of Pb and Zn in the different grain-size fractions of wastes indicate that the coarser particles show similar or even higher heavy metal concentrations than finer ones in the samples, although the concentrations of heavy metals tend generally to increase as the size fractions get finer. The heavy metal contents are very high, with maximum values of 31631, 57178, 2367 and 311.5 mg/kg for Pb, Zn, Cu and Cd, respectively. It is also shown that the residual fraction of Pb is less than that of Zn, accounting for 0.39%-15.75% and 14.3%-46.2%, respectively, of the total, and this is likely relative to Zn-silicate minerals formed from smelting. Although the relative partitioning of Pb and Zn is very low （0.03%- 1.3.% for Pb; 0.03% -3.3% for Zn）, the exchangeable fraction of the waste contains large amounts of heavy metals （1.5%-385 μg/g for Pb; 3-590 μg/g for Zn）. Heavy metals in exchangeable forms have the highest solubility to give the highest potential bioavailability in contrast to other chemical forms. Mineralogical study indicates that the wastes were found to be highly heterogeneous materials, dominated by quartz, feldspar, carbonatite, iron or/and aluminum vitric compounds and a few secondary mineral phases, and their contents vary with the type of smelting wastes. The secondary minerals formed from smelting and sequentially weathering are the major chemical phase for heavy metals. Complex composition of many phases and substitution of elements suggested that many of the phases were found to be non-stoichiometric compounds. Pb was found to be the main Pb phase in the wastes by precipitation or/and adsorption.     

Leaching Behavior of Fly Ashes from Power Plants

The Yanzhou mine district, located in southwestern Shandong Province, is about 1300 km2 with more than 8×109tons of proved coal reserves and there are 10 big power plants in this area. A large amount of coal ashes, which are regarded as waste materials, have been stockpiled in the area and have influenced the environment of the mine district. In this paper, analysis of fly ash samples from three power plants is carried out, the enrichment and concentration of trace elements, Pb, Zn, Cu and As, in coal ashes are analyzed, and petrological and mineralogical characteristics and chemical compositions of coal ashes are studied. The aim of this work is to provide basic scientific data for utilization of ashes and reduction of environmental pollutions.     

Resources of Kaolinite Rocks in China Coal Measures

The kaolinite rocks are very abundant in China coal mea-sures,most of which are very pure,excellent and in goodquality for industrial use.The geological feature,occurrence,origin and processing techniques are largely different fromthose of the traditional kaolins.The kaolinite rocks in Chinacoal measures are marvelous,but a large-scale kaolinite de-posit is rare in the world.The origin of kaolinite rocks in thecoal measures is under debate for a long time(Liu and Zhang,1 997;Liang,1 995;Boho…     

Distribution and Elimination of Lead Species in Soils Related to GAP of Chinese Medicinal Materials of Ligusticum Chuanxiong Hort

In this paper, the sequential extraction procedure was used for the selection of fractions of lead in seven stages corresponding to lead exchangeable, lead bounded to carbonates, to manganese oxides, to organic matters, to amorphous iron, and lead associated to crystallized iron, and to residuals. The vertical distributions of lead species were carried out in the soils related to good agriculture progress (GAP) of Chinese medical materials of Ligusticum chuanxiong Hort in Dujiangyan city and Wenchuan County, Sichuan Province. Based on those researches, it is found that the plant of Glycine Max (L.) Merr. has the character of lead enrichment and sorption, which is not reported in the literature. Using Glycine Max (L.) Merr. alternate planting with Ligusticum chuanxiong Hort is a valuable recommended in order to produce a high quality Chinese medical materials in order to eliminate the barrier on the beyond the lead limit for the import and export of Ligusticum chuanxiong Hort.     

Study on the forecasting method of tight gas "sweet" in the Shahezi group in Xujiaweizi

<正>The burial depth and the structural complexity of the layer in Shahezi groups are very difficult to predict the reservoir prediction due to the volcanic disturbance.In order to solve these difficulties,the reservoir prediction is carried out by dividing sequence in the vertical,dividing facies in the horizontal and the geological mode facies controlling.First of all,we need to analysis the petrophysical for different sequences based on wellbore     

Permeable Reactive Barrier for the treatment of contaminated surface water in Katedan industrial development area, Hyderabad, India

Permeable Reactive Barrier （PRB） is an emplacement of inert material （s） in the subsurface, designed to intercept a contaminated plume, provides a preferential flow path through the reactive media, and transforms the contaminant into environmentally acceptable forms to attain concentration remediation goals at the discharge of the barrier. The phenomena, which help in remediation within PRB, are adsorption/sorption, precipitation, oxidation/reduction and biodegradation. Various materials like zero-valent iron, zero-valent bi-metals, natural zeolites, organic carbon, fly ash, zeolites, limestone, activated alumina, apatites, etc. have been tried by many researchers to remove organic and inorganic contaminants. In USA, Canada, and many European countries commercial full-scale and pilot scale PRBs are successfully working. The design and installation of full scale PRBs needs laboratory treatability and dynamic flow column experiments？ The concept of PRB is being applied to treat contaminated surface water in the Katedan industrial area, Hyderabad, India. National Geophysical Research Institute （NGRI）, Hyderabad, India, conducted systematic studies in collaboration with Norwegian Geotechnical Institute （NGI）, Norway, to develop PRB technique to decontaminate the surface water pollution due to industrial effluent. A site assessment study in the Katedan Industrial Area, were carried out and water, soil and sediment from the lakes of the area were found to be polluted with high concentrations of heavy metals like As, Pb, Cr, Cd, Ni, etc. Adsorption studies at NGRI with synthetic samples and in-situ industrial effluent using different reactive media for removing contaminants like arsenic, chromium, cadmium, copper, nickel, lead and zinc have been carried out and yielded satisfactory results. The performance of zero-valent iron and limestone is encouraging in removing As,     

The Hizeh-Jan Kaolin Deposit of NW Iran:the TetradEffect in REE Distribution Patterns

The Hizeh-Jan kaolin deposit(northwest of Varzeghan, East-Azarbaidjan Province, NW Iran) is a product of the alteration of Eocene andesitic rocks. Based on mineralogical examinations, kaolinite, quartz, smectite, pyrophyllite, muscovite-illite, alunite, calcite, diaspore, goethite and hematite are the most abundant mineral phases in this deposit. The geochemical indicators, such as Y/Ho and Zr/Hf, indicate the non-CHARAC(non-Charge-radius control) behavior of these pairs, which are likely to be due to the occurrence of the tetrad effect phenomenon in this deposit. Simultaneous concave and convex shapes in the chondrite-normalized REE distribution patterns are a remarkable feature of the kaolin samples. Bivariate diagrams of the size of the third tetrad effect(T_3) versus geochemical parameters such as Y/Ho, Nb/Ta and Zr/Hf ratios display two distinct populations for the kaolin samples. The first population is characterized by high T_3 values(>0.13), which are near or on the fault zone. The second population is characterized by low T_3 values(<0.13), and are farther from the fault zone. The obtained results from the geochemical data have furnished compelling evidence that fluidrock interaction, overprint of hypogene processes by supergene ones, and structural control, are key controlling factors for the occurrence of tetrad effects in REE distribution patterns in the Hizeh-Jan kaolin deposit.     

On the Chemical Evolution of Upper Mantle of the Early Earth—An Experimental Study on Melting of the Silicate Phase in Jilin Chondrite at High Pressures

Relatively old ages of chondrites(normally around 4.5Ga)suggest that their parent bodies did not experience any mely-fractionation under high temperature and high pressure conditions pertaining to the interior of terrestrial plaets.Therefore,it is reasonable to take chondrites as starting materials in the study of the chemical evolution of the early earth.The sillicate phase in the Jilin chondrite (H5)was chosen for this purpose because it possesses a chemical composition similar to that of the primitive mantle.The melting experiment was carried out at 20-30 k bar and has rsulted in a product which contains1-5% melts in addition to solid cryustal phase.The chemical composition of the melt phases and the partitioning of various elements between the coexisting silicate melts are geochemically similar to those of anatectic rocks on the earth.This can thus serve as the basis for discussing the chemical evolution of the early upper mantle.     

Sorption properties of 1, 3, 5-trichlorobenznene on kerogen

Kerogen is an important organic matter fraction widely spread in soils and sediments. It plays a major role in the sorption and sequestration of hydrophobic organic contaminants （HOCs） such as trichlorobenzene （TCB）. It is known that kerogen is geochemically heterogeneous due to the differences in source materials and diagenesis history. We hypothesized that kerogen derived from different source materials and diagenetic history exhibits different sorption properties for TCB. We employed two different kerogen materials （coals） as the original materials and two series of kerogen for a given series with an identical source material but different alteration history were yielded through thermal treatment at temperature ranging from 200 to 500℃. The original and treated materials were characterized for their physicochemical properties. Sorption experiments were conducted with batch reactor systems using 1, 3, 5-TCB as the HOCs sorbates and the original and treated materials as the sorbents.     

Geochemical and Mineralogical Characteristics of Pleistocene Lignites and Associated Sediments of Marathousa Coal Field,Central Peloponnese,Greece

The mineralogy and geochemistry data are presented for thirty-seven shales,four concretions,two carbonate sediments and seven lignites from the Marathousa coal field of the Megalopolis Basin in Greece.The argillaceous rocks consist of chlorite,illite,kaolinte,albite,quartz.opal-A,calcite and dolomite;the concretions of aragonite,gypsum and pyrite;and the carbonate rocks of calcite,quartz and illite.The mineral matter in the lignites consists of gypsum,quartz,albite,chlorite,illite,opal-A,dolomite,pyrite,and rarely calcite and kaolinite Athree-factor model explains the total variaition of major and trace elements in the argillaceous sediments.The first factor is an aluminosilicate factor and involves the following elements:Al,Si,Mg,Na,K,Ti,Mn,Nb,Y,Rb,Zn,Cu,Ni,Cr,Nband V,associated with chlorite,albite and illite.The second factor involves the elements Ca,Sr,Ba,Znand Sc and is related to carbonate lithology and mainly the carbonate concretions with gypsum.The third factor involves Fe and Ce with a weak association with Mn.The diagenesis of the Marathousa sediments and lignites was not very advanced as indicated by (a) the total thickness of the sequence (500m),(b) the presence of biogenic silica(opal-A) and (c) the age of the deposit(Pleistocene).FOr these reasons the rpresence of chlorite,illite and kaolinite in the sediments and lignite is due not to diagenetic reactions but to weathering of the flysch and metamorphic rocks at the edges of the Megalopolis Basin and transport of the weathering products(illite,chlorite,kaolinite)into the basin of deposition.The diagenetic minerals of the Marathousa sequence include pyrite,gypsum,dolomite and aragonite.     

The Slab-Mantle Interaction in Continental Subduction Channels

<正>The subduction channel is the dynamic site of mass and energy exchange between the slab and mantle.It is evolved into the subduction factory by processing raw materials into different products.The raw materials are sedimentary crust,igneous crust,and lithospheric mantle(juvenile or ancient).They are carried with the subducting     

Distribution and Elimination of Lead Species in Soils Related to GAP of Chinese Medicinal Materials of Ligusticum Chuanxiong Hort

In this paper，the sequential extraction procedure was used for the selection of fractions of lead in seven stages corresponding to lead exchangeable，lead bounded to carbonates，to manganese oxides，to organic matters，to amorphous iron，and lead associated to crystallized iron，and to residuals． The vertical distributions of lead species were carried out in the soils related to good agriculture progress（GAP）of Chinese medical materials of Ligusticum chuanxiong Hort in Dujiangyan city and Wenchuan County，Sichuan Province．Based on those researches，it is found that the plant of Glycine Max（L．） Merr．has the character of lead enrichment and sorption， which is not reported in the literature．Using Glycine Max（L．）Merr．alternate planting with Ligusticum chuanxiong Hort is a valuable recommended in order to produce a high quality Chinese medical materials in order to iminate the barrier on the beyond the lead limit for the import and export of Ligusticum chuanxiong Hort．     

http://www.sciencedirect.com/science/article/pii/S1674987111000478

Convective heat transfer associated with the circulation of pore-fluid in porous rocks and fractures within the upper crust of the Earth is substantial when the temperature gradient is sufficiently high.In order to understand the process of Sn-polymetallic mineralization in the Dachang ore district of Guangxi,a finite element method has been used in this study to simulate both pore-fluid flow and heat transfer in this district.On the basis of related geological,tectonic and geophysical constraints,a computational model was established.It enables a computational simulation and sensitivity analysis to be carried out for investigating ore-forming pore-fluid flow and other key factors that may affect hydrothermal ore genesis in the district.The related simulation results have indicated that:(1) permeable fault zones in the Dachang ore district can serve as preferential pathways for pore-fluid flow on a regional-scale;and(2) the pore-fluid flow can affect the salinity distribution.This latter factor is part of the reason why Sn-polymetallic mineralization has taken place in this district.     

Measurements of ^222Rn and ^220Rn with a Large Size Collector of Radon Progeny

Radon concentrations in high background radiation areas in the south are higher than those of others in China, especially ^220Rn concentration is significantly high. Therefore, measurements of ^222Rn and ^220Rn concentrations should be carried out there. This paper introduces a large size collector of radon progeny and its applications. The collector is a sheet of polyvinyl chloride fiber with electrostatics of (-500 V)-(-700 V). Its size (60 mm in diameter) is larger than those of others (26 mm in diameter) that work with the same principle. The collector is more effective to adsorb radon progeny than most of others. The equipment of ZnS(Ag) Scintillation Counting System is available for large size collectors to detect radon progeny. Therefore, its sensitivity of measurement is higher than that of others. According to the different half lives of radon progeny, and based on both theory and experiments, a formula for discrimination and calculation of ^222Rn and ^220Rn concentrations is deduced. The ^222Rn and ^220Rn concentrations were surveyed with electrostatic collectors of radon progeny on the campus of commercial school and some other areas in Hainan, southern China. Neither ^222Rn nor ^220Rn concentration was found significantly high. However, several faults underground were delineated. The collector is also used to study radon transportation. Results indicate that radon changes regularly with date when it has transported for a certain distance. Velocities of radon migration in the four media are quite different. Radon migrates more quickly in vertical tube than in the horizontal tube.     

ROLE OF ORGANIC MATTER IN THE FORMATION OF KAOLINITE ROCKS OF LATE-PALAEOZOIC COAL MEASURES, NORTH CHINA

1. IntroductionThe kaolinite rocks (including tonstein, flint clay and soft kaolin clay) are very abundant in Late-Palaeozoic coal measures of North China, most of which are very pure, good quality and excellent materials for industrial application. In the last two decades, many origin models of kaolinite rocks in coal-bearing strata, especially of tonsteins, have been proposed by geologists all over the world (Williamson I A, 1970; Bohor B F, 1993; Liu Qinfu, 1997). The common view for t…